Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “combustion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Implications of Low Particulate Matter Emissions on System Fuel Efficiency for High Efficiency Clean Combustion

Advanced diesel combustion regimes such as High Efficiency Clean Combustion (HECC) offer the benefits of reduced engine out NOX and particulate matter (PM) emissions. Lower PM emissions during advanced combustion reduce the demand on diesel particulate filters (DPFs) and can, thereby, reduce the fuel penalty associated with DPF regeneration. In this study, a SiC DPF was loaded and regenerated on a 1.7-liter 4-cylinder diesel engine operated in conventional and advanced combustion modes at different speed and load conditions. A diesel oxidation catalyst (DOC) and a lean NOX trap (LNT) were also installed in the exhaust stream. Five steady-state speed and load conditions were weighted to estimate Federal Test Procedure (FTP) fuel efficiency. The DPF was loaded using lean-rich cycling with frequencies that resulted in similar levels of NOX emissions downstream of the LNT. The pressure drop across the DPF was measured at a standard point (1500 rpm, 5.0 bar) before and after loading, and a P rise rate was determined for comparison between conventional and advanced combustion modes. Higher PM emissions in conventional combustion resulted in a higher rate of backpressure rise across the DPF at all of the load points leading to more frequent DPF regenerations and higher fuel penalty. The fuel penalty during conventional combustion was 4.2% compared with 3.1% for a mixture of conventional and advanced modes.

33 ADVANCED PROPULSION SYSTEMS↗

Combustion characteristics and kinetics of partial gasified coal char

Combustion characteristics and kinetics of partial gasified coal char (PGC-char) were investigated in this article. Two-stage distributed activation energy model (TS-DAEM) and simple model were used to model the combustion kinetics. The experimental results showed that the combustion characteristics of PGC-chars varied with coal types and percentage of gasification. Modeling results showed that TS-DAEM could suitably describe the combustion of PGC-char. The activation energy and pre-exponential factor increased with the increasing of PGC-char gasification percentage, but the percent of high reactivity part decreased. This indicated that the difficulty reactive part in the partial gasified coal char became more and more with the gasification conversion. However, simple model wasn't fit to describe the combustion of PGC-char, especially for PGC-chars with obvious second peak in combustion DTG curves.

01 COAL, LIGNITE, AND PEAT↗

Effect of Oxyfuel Combustion on Superheater Corrosion

Combustion of coal in an oxygen environment (as opposed to air) will facilitate the sequestering of carbon dioxide by minimizing the amount of nitrogen in the exit gas stream. The presence of higher levels of certain gases associated with oxyfuel combustion (eg, CO2, SO2, and H2O) may impact the corrosion of waterwalls, superheaters, headers, reheaters, and other boiler components. Research is being conducted on bare and ash-embedded boiler tube materials in simulated oxyfuel- combustion and air-combustion environments at a superheater temperature of 675°C. Alloys were exposed at temperature to two different gaseous environments. Preliminary results show: (1) an increase in corrosion rate of bare K02707, K11547, K21590, K91560, K92460, S30409, S34700, and N06617 exposed to the oxyfuel combustion environment when compared to the air combustion environment; (2) an increase in corrosion rate of alloys K21590, K92460, S34700, and N06617, when embedded in ash in comparison to bare exposure; and (3) no effect of gaseous environment on alloy corrosion rate when embedded in ash.

36 MATERIALS SCIENCE↗

Greenhouse impact due to the use of combustible fuels: Life cycle viewpoint and relative radiative forcing commitment

Extensive information on the greenhouse impacts of various human actions is important in developing effective climate change mitigation strategies. The greenhouse impacts of combustible fuels consist not only of combustion emissions but also of emissions from the fuel production chain and possible effects on the ecosystem carbon storages. It is important to be able to assess the combined, total effect of these different emissions and to express the results in a comprehensive way. In this study, a new concept called relative radiative forcing commitment (RRFC) is presented and applied to depict the greenhouse impact of some combustible fuels currently used in Finland. RRFC is a ratio that accounts for the energy absorbed in the Earth system due to changes in greenhouse gas concentrations (production and combustion of fuel) compared to the energy released in the combustion of fuel. RRFC can also be expressed as a function of time in order to give a dynamic cumulative picture on the caused effect. Varying time horizons can be studied separately, as is the case when studying the effects of different climate policies on varying time scales. The RRFC for coal for 100 years is about 170, which means that in 100 years 170 times more energy is absorbed in the atmosphere due to the emissions of coal combustion activity than is released in combustion itself. RRFC values of the other studied fuel production chains varied from about 30 (forest residues fuel) to 190 (peat fuel) for the 100-year study period. The length of the studied time horizon had an impact on the RRFC values and, to some extent, on the relative positions of various fuels.

01 COAL, LIGNITE, AND PEAT↗

Spatiotemporal flame propagations, combustion and solid particle emissions from lean and stoichiometric gasoline direct injection engine operation

Increased particle number and mass emissions in gasoline direct injection (GDI) engines should require to investigate in-cylinder flame and combustion characteristics associated with primary source of particle emissions. In this article, in-cylinder spatiotemporal flame luminosity is quantitatively characterized to features combustion process and solid particle emissions from a GDI engine operating in two lean and one stoichiometric modes. Low- and high-steady state operating points were used to compare combustion strategies on flame development and emission characteristics. A fiber-optic sensor composed of eight measurement channels detected the flame front and the direction of the flame propagation in the combustion chamber. Solid particle emissions in the exhaust were measured using an engine exhaust particle sizer and a micro soot sensor. Results of the experiments showed that two lean combustion modes by injection strategies resulted in distinct combustion and flame development. Lean combustion modes generated high diffusion flame by burning stratified rich-mixture. Although the lean cases resulted in strong diffusion flames, the lean-homogeneous produced similar particle size distributions with the stoichiometric mode with high ash particles. Piston pool fires on the piston surface in the lean-stratified mode induced a large accumulation mode with high particle mass concentrations.

42 ENGINEERING↗

Numerical and experimental studies on effects of moisture content on combustion characteristics of simulated municipal solid wastes in a fixed bed

Highlights: • The effects of moisture content on the burning process of MSW are investigated. • A two-dimensional mathematical model was built to simulate the combustion process. • Temperature distributions, process rates, gas species were measured and simulated. • The The conversion ratio of C/CO and N/NO in MSW are inverse to moisture content. - Abstract: In order to reveal the features of the combustion process in the porous bed of a waste incinerator, a two-dimensional unsteady state model and experimental study were employed to investigate the combustion process in a fixed bed of municipal solid waste (MSW) on the combustion process in a fixed bed reactor. Conservation equations of the waste bed were implemented to describe the incineration process. The gas phase turbulence was modeled using the k–ε turbulent model and the particle phase was modeled using the kinetic theory of granular flow. The rate of moisture evaporation, devolatilization rate, and char burnout was calculated according to the waste property characters. The simulation results were then compared with experimental data for different moisture content of MSW, which shows that the incineration process of waste in the fixed bed is reasonably simulated. The simulation results of solid temperature, gas species and process rate in the bed are accordant with experimental data. Due to the high moisture content of fuel, moisture evaporation consumes a vast amount of heat, and the evaporation takes up most of the combustion time (about 2/3 of the whole combustion process). The whole bed combustion process reduces greatly as MSW moisture content increases. The experimental and simulation results provide direction for design and optimization of the fixed bed of MSW.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantum Chemical Study of Supercritical Carbon Dioxide Effects on Combustion Kinetics

In oxy-fuel combustion, the pure oxygen (O 2 ), diluted with CO 2 is used as oxidant instead air. Hence, the combustion products (CO 2 and H 2 O) are free from pollution by nitrogen oxides. Moreover, high pressures results in the near-liquid density of CO 2 at supercritical state (sCO 2 ). Unfortunately, the effects of sCO 2 on the combustion kinetics are far from being understood. In order to assist in this understanding, in this work we are using quantum chemistry methods. Here we investigate potential energy surfaces of important combustion reactions in the presence of carbon dioxide melocule. All transition states, reactant and product complexes are reported for three reactions: H 2 CO+HO 2 →HCO+H 2 O 2 (R1), 2HO 2 →H 2 O 2 +O 2 (R2), and CO+OH→CO 2 +H (R3). In the reaction R3, covalent binding of CO 2 to OH radical and then CO molecule opens a new pathway, including hydrogen transfer from oxygen to carbon atoms followed by CH bond dissociation. Compared to bimolecular OH+CO mechanism, this pathway reduces the activation barrier by 5 kcal/mol, and is expected to accelerate the reaction. This is the first report of autocatalytic effect in combustion. In case of hydroperoxyl self-reaction 2HO 2 →H 2 O 2 +O 2 the intermediates, containing covalent bonds to CO 2 were found not to be competitive. However, the spectator CO 2 molecule is able to stabilize the cyclic transition state and lower the barrier by 3 kcal/mol. Formation of covalent intermediates was also discovered in H 2 CO+HO 2 →HCO+H 2 O 2 reaction, but these specie lead to substantially higher activation barriers which makes them unlikely to play role in hydrogen transfer kinetics. The van der Waals complexation with carbon dioxide also stabilized transition state and reduces reaction barrier. Lastly, these results indicate that CO 2 environment is likely to have catalytic effect on combustion reactions, which needs to be included in kinetic combustion mechanisms in supercritical CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Leaching hierarchies in co-combustion residues

The leaching propensities from co-combustion residues of 10 trace elements (Be, V, Cr, Zn, As, Se, Cd, Ba, Hg, Pb) were evaluated. Eight fuels varying from coal blends to coal and secondary fuel mixtures to ternary mixtures were co-combusted in two reactor configurations and at two temperatures (850 and 950{sup o}C). The ash was subjected to a miniaturized toxicity characteristic leaching procedure (TCLP) developed for this study, and the trace element content in the leachate was analyzed, andpercentage retentions of elements in the ashes and leachates were calculated. Hg and Se were almost completely volatilized during combustion and, therefore, were largely absent from the ashes, in all cases. For the other trace elements, it was not possible to establish a hierarchy of relative trace-element retention. Retention was primarily a function of the combustion method, with no clear effect of temperature retention being observed. The measured trace-element retentions were compared to those predicted by thermodynamic equilibrium modeling, using the MTDATA software. The model successfully predicted the measured values in many cases; however, many anomalies were also noted. From trace-element analysis in the leachates, an extent-of-leaching hierarchy could be established. The elements that underwent low degrees of leaching were Zn, Hg, Pb, low to moderate leaching were Be, Cr, and Cd, and thoseleached to a greater extent were V, As, Se, and Ba. This hierarchy was observed for all fuels and conditions studied. Leaching was found to be a strong function of the combustion temperature and combustion method. When assessing the potential toxicity of leachate from co-combustion residues, Zn, Hg, and Pb may be deemed of least concern, while a greater emphasis should be placed in mitigating the release of the remaining elements. 18 refs., 7 tabs.

01 COAL, LIGNITE, AND PEAT↗

Characteristics of particulate carbon emissions from real-world Chinese coal combustion

Particulate matter emissions from a series of different Chinese coal combustion systems were collected and analyzed for elemental and organic carbon (EC, OC), and molecular markers. Emissions from both industrial boilers and residential stoves were investigated. The coal used in this study included anthracite, bituminite, and brown coal, as well as commonly used coal briquettes produced in China for residential coal combustion. Results show significant differences in the contribution of carbonaceous species to particulate mass emissions. Industrial boilers had much higher burn out of carbon yielding particulate matter emissions with much lower levels of OC, EC, and speciated organic compounds, while residential stoves had significantly higher emissions of carbonaceous particulate matter with emission rates of approximately 100 times higher than that of industrial boilers. Quantified organic compounds emitted from industrial boilers were dominated by oxygenated compounds, of which 46-68% were organic acids, whereas the dominate species quantified in the emissions from residential stoves were PAHs (38%) and n-alkanes (20%). An important observation was the fact that emission factors of PAHs and the distribution of hopanoids were different among the emissions from industrial and residential coal combustion even using the same coal for combustion. Although particulate matter emissions from industrial and residential combustion were different in many regards, picene was detected in all samples with detectable OC mass concentrations, which supports the use of this organic tracer for OC from all types of coal combustion. 17{alpha}(H),21{beta}(H)-29-norhopane was the predominant hopanoid in coal combustion emissions, which is different from mobile source emissions and may be used to distinguish emissions from these different fossil fuel sources. 32 refs., 4 figs., 1 tab.

01 COAL, LIGNITE, AND PEAT↗

Selective Chemical Looping Combustion of Terminal Alkynes in Mixtures with Alkenes

The selective combustion of terminal alkynes in mixtures with alkenes is demonstrated during anaerobic reduction half-cycles on bulk bismuth oxide (Bi 2 O 3 ) as an approach to remove alkynes, which act as inhibitors in olefin polymerization. Bi 2 O 3 combusts phenylacetylene in styrene, 3-methylphenylacetylene in 3-methylstyrene, propyne in propylene, 1-hexyne in 1-hexene, and 1-octyne in 1-octene, with alkyne combustion selectivities exceeding 96%. Near unity reaction orders for hydrocarbon consumption during reduction half-cycles are consistent with combustion pathways initiated by rate-determining initial C–H activation, which drive selective alkyne combustion through intrinsic differences in the first-order rate constants for alkyne and alkene combustion rather than preferential adsorption of alkynes on Bi 2 O 3 surfaces. Computational assessments of initial C–H activation pathways for alkynes and alkenes on (010) α-Bi 2 O 3 surfaces using density functional theory illustrate that heterolytic transition states which form proton-carbanion pairs on Bi–O sites kinetically favor the activation of alkynes rather than alkenes due to differences in C–H bond acidity, and the barrier for heterolytic C–H activation is dictated in part by the sum of the molecular deprotonation energy and the energy to bind an R – carbanion to a Bi site in its transition-state geometry. Finally, these heterolytic reactivity channels during selective chemical looping combustion present novel routes for purifying olefin gas streams containing alkyne impurities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Co-combustion of pellets from Soma lignite and waste dusts of furniture works

In this work, volatiles and char combustion behaviors of the fuel pellets prepared from a low quality lignite and the dusts of furniture works and their various blends were investigated in an experimental fixed bed combustion system through which air flowed by natural convection. Combustion data obtained for varied bed temperatures, mass of pellets, and blend compositions has showed that ignition times of the pellets decreased and volatiles combustion rates tended to increase with the burning temperature. It was concluded that some synergy had existed between lignite and lower ratios of furniture work dusts, which was indicated by a prompt effect on the volatiles combustion rates. Char combustion rates of blend pellets have depended predominantly on the amount of lignite in the blend. The amounts of combustion residues of the pellets were considerably higher than those calculated from individual ash contents of the raw materials and related to lignite ratio in the blends.

01 COAL, LIGNITE, AND PEAT↗

Oxy-Combustion Modeling for Direct-Fired Supercritical CO 2 Power Cycles

We report that supercritical CO 2 power cycles for fossil energy power generation will likely employ oxy-combustion at very high pressures, possibly exceeding 300 bar. At these high pressures, a direct fired oxy-combustor is more likely to behave like a rocket engine than any type of conventional gas turbine combustor. Issues such as injector design, wall heat transfer, and combustion dynamics may play a challenging role in combustor design. Computational fluid dynamics modeling will not only be useful, but may be a necessity in the combustor design process. To accurately model turbulent reacting flows, combustion submodels appropriate for the conditions of interest as defined by the turbulent time and length scales as well as chemical kinetic time scales are necessary. Here, this paper presents a comparison of various turbulence–chemistry interaction (TCI) modeling approaches on a canonical, single injector, direct-fired sCO 2 combustor. Large eddy simulation is used to model the turbulent combustion process with varying levels of injector oxygen concentration while comparing the effect of the combustion submodel on CO emissions and flame shape. While experimental data are not yet available to validate the simulations, the sensitivity of CO production and flame shape can be studied as a function of combustion modeling approach and oxygen concentration in an effort to better understand how to approach combustion modeling at these unique conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Double-Wiebe Function for Reactivity Controlled Compression Ignition Combustion Using Reformate Diesel

Abstract Reactivity controlled compression ignition (RCCI) combustion has previously been proposed as a method to achieve high fuel conversion efficiency and reduce engine emissions. A single-fuel RCCI combustion strategy can have decreased fuel system complexity by using a reformate fuel for port fuel injection and the parent fuel (diesel) for direct injection. This paper presents a one-dimensional computational model of a compression ignition engine with single-fuel RCCI. A Wiebe function is used to predict the combustion process by representing the mass fraction burned (MFB) on a crank angle resolved basis. One single-Wiebe function (SWF) and two double-Wiebe functions(DWFs) were fitted to experimentally derive MFB data using the least-square method. The fitted results were compared with MFBs calculated from experimental data to verify the accuracy. The SWF did not fully capture the MFB curve with high fidelity while the detailed DWF captured the MFB curve within a root mean square error of 1.4%. The reduced double-Wiebe function (RDWF) also resulted in a predicted combustion profile with similar accuracy. Hence, the RDWF was used in a GT-power thermodynamic study to understand the effects of the low-temperature heat release (LTHR) fraction and combustion phasing on combustion characteristics. At optimum phasing of 5–10 crank angle degree after the top dead center, increasing the LTHR fraction from 20% to 60% resulted in the fuel conversion efficiency increasing from 39.5% to 41.1%, thus suggesting that the reformate fuel-based RCCI strategy is viable to unlock improved combustion performance.

Energy & Fuels↗

Experimental Combustion and Flame Characterization of a Chemical Looping-Based Oxidative Dehydrogenation Byproduct Fuel Mixture Containing High CO2 Dilution

Abstract This study investigates the combustion performance of a CO2-rich fuel mixture containing ethane and methane as active species using a constant volume combustion chamber. This fuel is obtained as a byproduct of a chemical looping-based oxidative dehydrogenation (Cl-ODH) process ethylene production. The byproduct gas mixture has 40.79% CO2, 39.49% ethane, and 4.88% methane by weight with other minor compounds. Using this fuel for energy extraction would improve the process efficiency of the ethane to ethylene conversion. After initial combustion modeling, the gas fuel mixture was reduced to just the major species: CO2, ethane, and methane. The mixture was then tested for flammability limits and combustion performance under spark-ignition conditions. Effects of ambient conditions like temperatures between 300 and 400 K with initial pressures from 1 to 10 bar were tested. The effects of stoichiometry were tested to understand flame velocities and heat release. The fuel mixture showed an overall reduced flame velocity compared to gasoline. Instability in combustion was believed to be caused by the dissociation of ethane under elevated conditions. At higher pressures, the flame produces lower cumulative heat release. Simulations were also performed using a model tuned to replicate the operations of the combustion chamber used in the experiments. Heat release and unburnt fuel mass data were calculated to identify the discrepancies in the combustion completeness at elevated pressures. The effects of CO2 quenching the flame coupled with the increased dissociation of the fuel species can lead to up to more than 75% of the fuel mixture being unburnt. Data from this study were used to modify a small-scale spark-ignition engine to use this fuel and produce usable energy.

Energy & Fuels↗

A control-oriented combustion model framework for compression ignition engines operating on low-reactivity fuel

This work focuses on zero-dimensional modeling of the heat release rate in a compression ignition engine operating on gasoline-like fuels. Due to the properties of gasoline, such as high volatility and longer ignition delay than diesel, the injection strategies can vary significantly from the operation with conventional diesel fuel. Different injection strategies are commonly used to achieve varying degrees of in-cylinder stratification in order to shape the combustion event and maximize efficiency. The proposed zero-dimensional combustion model was developed to account for the different stages in combustion caused by the fuel stratification. As the ignition delay model is an integral part of the entire combustion process and significantly affects the prediction accuracy, special attention has been paid to local phenomena influencing ignition delay. A one-dimensional spray model by Musculus and Kattke was employed in conjunction with a Lagrangian tracking approach in order to estimate the local air–fuel ratio within the spray tip, as a proxy for reactivity. The local air–fuel ratio, in-cylinder temperature and pressure were used in an integral fashion to estimate the ignition delay. Heat release rates were modeled using first-order non-linear differential equations. The proposed combustion model was validated against experimental data of a heavy-duty compression ignition engine with up to three injection events at mostly 1038 r/min and 14 bar brake mean effective pressure. Further validation of the model was carried out at other engine loads and speeds. Model prediction errors in CA50 of less than 1 °CA across all conditions were found. Modeling results of other combustion metrics such as combustion duration and indicated mean effective pressure are also highly satisfactory. In addition, the model has been shown to be capable of estimating the ringing intensity for most conditions.

Pamminger, Michael↗

Exploring the potential benefits of high-efficiency dual-fuel combustion on a heavy-duty multi-cylinder engine for SuperTruck I

In support of the Daimler SuperTruck I team’s 55% brake thermal efficiency (BTE) pathway goal, researchers at Oak Ridge National Laboratory performed an experimental investigation of the potential efficiency and emissions benefits of dual-fuel advanced combustion approaches on a modified heavy-duty 15-L Detroit™ DD15 engine. For this work, a natural gas port fuel injection system with an independent injection control for each cylinder was added to the DD15 engine. For the dual-fuel strategies investigated, 65%–90% of the total fuel energy was supplied through the added port fuel injection natural gas (NG) fueling system. The remaining fuel energy was supplied by one or more direct injections of diesel fuel using the production high pressure diesel fueling system. The production DD15 air handling system and combustion geometry were unmodified for this study. Efficiency and emissions with dual-fuel strategies including both low temperature combustion (LTC) and non-LTC approaches such as dual fuel direct-injection were investigated along with control authority over combustion phasing. Parametric studies of dual-fuel NG/diesel advanced combustion were conducted in order to experimentally investigate the potential of high-efficiency, dual-fuel combustion strategies to improve BTE in a multi-cylinder engine, understand the potential reductions in engine-out emissions, and characterize the range of combustion phasing controllability. Characterization of mode transitions from mixing-controlled diesel pilot ignition to kinetically controlled ignition is presented. Key findings from this study included a reproducible demonstration of BTE approaching 48% at up to a 13-bar brake mean effective pressure with significant reductions in engine-out NOx and soot emissions. Additional results from investigating load transients in dual-fuel mode and initial characterization of particle size distribution during dual-fuel operation are presented.

33 ADVANCED PROPULSION SYSTEMS↗

Development and evaluation of a skeletal mechanism for EHN additized gasoline mixtures in large Eddy simulations of HCCI combustion

Advanced Low Temperature Combustion modes, such as the Sandia proposed Additive-Mixing Fuel Injection (AMFI), can unlock significant potential to boost fuel conversion efficiency and ultimately improve the energy conversion of internal combustion engines. This is a novel improved combustion process that is enabled by supplying small (<5%) variable amounts of autoignition improver to the fuel to enhance the engine operation and control. Common, diesel-fuel ignition-quality enhancing additive, 2-ethylexyl nitrate (EHN), is doped into gasoline to enable Sandia LTGC + AMFI combustion. This manuscript focuses on the development of a reduced sub-mechanism for EHN chemical kinetics at engine relevant conditions that is implemented into a skeletal mechanism for chemical kinetic studies of gasoline surrogate fuels. The mechanism validation utilized zero-dimensional numerical simulations and comparison to shock tube ignition-delay data of pure and EHN-doped n-heptane. Additional validation is presented with Homogeneous Charge Compression-Ignition (HCCI) engine data of pure and EHN-doped research-grade E10 gasoline. Then, the mechanism was deployed in a 3-D computational fluid dynamics (CFD) using Large Eddy Simulations (LES) to model the HCCI engine experiments of 0.4% vol EHN additized E10 gasoline at several equivalence ratios. Simulations showed a very good performance of the mechanism, and the model accurately reproduced (a) the ignition point, (b) combustion phasing, (c) combustion duration, and (d) the peak of the heat release rates of the engine experiments. The results show that EHN promotes Low-Temperature Heat Release, ultimately driving the gasoline to autoignite at thermodynamic conditions where the fuel would not otherwise ignite. Overall, this work demonstrates a viable reduced chemical-kinetic mechanism for EHN and shows that it can be combined with a skeletal gasoline mechanism for CFD-LES analysis of well-mixed LTGC that matches well with experimental results. The CFD-LES analysis also shows the spatial distribution of EHN-fuel interactions that control the autoignition throughout the combustion chamber.

Guleria, Gaurav↗

Oxy-Combustion Boiler Material Development

Under U.S. Department of Energy Cooperative Agreement No. DE-NT0005262 Foster Wheeler North America Corp conducted a laboratory test program to determine the effect of oxy-combustion on boiler tube corrosion. In this program, CFD modeling was used to predict the gas compositions that will exist throughout and along the walls of air-fired and oxy-fired boilers operating with low to high sulfur coals. Test coupons of boiler tube materials were coated with deposits representative of those coals and exposed to the CFD predicted flue gases for up to 1000 hours. The tests were conducted in electric tube furnaces using oxy-combustion and air-fired flue gases synthesized from pressurized cylinders. Following exposure, the test coupons were evaluated to determine the total metal wastage experienced under air and oxy-combustions conditions and materials recommendations were made. Similar to air-fired operation, oxy-combustion corrosion rates were found to vary with the boiler material, test temperature, deposit composition, and gas composition. Despite this, comparison of air-fired and oxy-fired corrosion rates showed that oxy-firing rates were, for the most part, similar to, if not lower than those of air-firing; this finding applied to the seven furnace waterwall materials (wrought and weld overlay) and the ten superheater/reheater materials (wrought and weld overlay) that were tested. The results of the laboratory oxy-combustion tests, which are based on a maximum bulk flue gas SO 2 level of 3200 ppmv (wet) / 4050 ppmv (dry), suggest that, from a corrosion standpoint, the materials used in conventional subcritical and supercritical, air-fired boilers should also be suitable for oxy-combustion retrofits. Although the laboratory test results are encouraging, they are only the first step of a material evaluation process and it is recommended that follow-on corrosion tests be conducted in coal-fired boilers operating under oxy-combustion to provide longer term (one to two year) data. The test program details and data are presented herein.

20 FOSSIL-FUELED POWER PLANTS↗