Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “body wave”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Effects of forebody strakes and Mach number on overall aerodynamic characteristics of configuration with 55 deg cropped delta wing

A wind tunnel data base was established for the effects of chine-like forebody strakes and Mach number on the longitudinal and lateral-directional characteristics of a generalized 55 degree cropped delta wing-fuselage-centerline vertical tail configuration. The testing was conducted in the 7- by 10-Foot Transonic Tunnel at the David Taylor Research Center at free-stream Mach numbers of 0.40 to 1.10 and Reynolds numbers based on the wing mean aerodynamic chord of 1.60 x 10(exp 6) to 2.59 x 10(exp 6). The best matrix included angles of attack from 0 degree to a maximum of 28 degree, angles of sidesip of 0, +5, and -5 degrees, and wing leading-edge flat deflection angles of 0 and 30 degrees. Key flow phenomena at subsonic and transonic conditions were identified by measuring off-body flow visualization with a laser screen technique. These phenomena included coexisting and interacting vortex flows and shock waves, vortex breakdown, vortex flow interactions with the vertical tail, and vortices induced by flow separation from the hinge line of the deflected wing flap. The flow mechanisms were correlated with the longitudinal and lateral-directional aerodynamic data trends.

Erickson, Gary E.↗
NASA NTRS1999

Hypersonic Flow Control Using Upstream Focused Energy Deposition

A numerical study of centerline and off-centerline power deposition at a point upstream of a two-dimensional blunt body at Mach 6.5 at 30 km altitude are presented. The full Navier-Stokes equations are used. Wave drag, lift, and pitching moment are presented as a function of amount of power absorbed in the flow and absorption point location. It is shown that wave drag is considerably reduced. Modifications to the pressure distribution in the flow field due to the injected energy create lift and a pitching moment when the injection is off-centerline. This flow control concept may lead to effective ways to improve the performance and to stabilize and control hypersonic vehicles.

Riggins David W.↗
NASA NTRS2004

Seal for a rotating member

A face seal assembly is provided having an annular seal body mounted in an axially moveable relationship to a seal support structure. A piston ring is disposed between the annular seal body and the seal support structure forming a secondary seal. A first locator spring, which is an annular wave spring, is disposed between said seal support structure and the piston ring to urge the piston ring in an axial direction. Optionally, a second locator spring, also a wave spring, may be disposed between the piston ring and the seal support structure for urging the piston ring in a radial direction.

Brauer, John Christopher↗
NASA NTRS2014

Data Processing and Experimental Design for Micrometeorite Impacts in Small Bodies

Comets and asteroids have been altered from their original "pristine" state by impacts occurring throughout their 4.5 billion year lives: [1]. Proof of shock deformation has been detected in the crystal structure of several Stardust samples from Comet Wild 2 [2, 3]. Analyses indicated that the planar dislocations in the crystal structure of the minerals had been imparted by impacts sustained during their lives, and not due to the aerogel capture process. Distortions to crystal structure also affect the ideal absorption spectra in the infrared, and [4], thus providing indirect evidence of its impact history and a means of remotely investigating the impact history of small bodies through comparing laboratory spectra with spectra observed by telescopes or spacecraft. -The effects of impacts propagating shock waves through minerals were investigated through laboratory impact experiments. Utilizing NASA Johnson Space Center's Experimental Impact Laboratory, projectiles were fired from the vertical gun at velocities ranging from 2.0 to 2.8 km/sec, projected impact velocities between Kuiper Belt Objects. Two types of projectiles were used, including spherical alumina ceramic, whose density mimics that of rock, and cylinders made from the same material that they impacted. The target materials chosen for testing included: OLIVINES forsterite (Mg2SiO4) and fayalite, Fe2SiO4); PYROXENES enstatite (Mg2Si2O6) and diopside (MgCaSi2O6); and CARBONATES magnesite (MgCO3) and siderite (FeCO3). Targets were impacted at either 25 C or cooled to -20 C to examine the effects of temperature, if any, on lattice distortions during the shock propagation. As comets and asteroids can undergo a wide range of temperatures in their orbital lifetimes, the effect of temperature on the equation of state of minerals being shocked needs to be examined for interpreting the results of these experiments. The porosity of the target mineral is varied by either grinding it into a powder/granular texture or as whole mineral rocks to investigate the differences in shock propagation when voids are present. By varying velocity, ambient temperature, and porosity, we can investigate different variables affecting impacts in the solar system. -Data indicates that there is a non-linear relationship between peak shock pressure and the variation in infrared spectral absorbances by the distorted crystal structure. The maximum variability occurs around 37 GPa in enstatite and forsterite. The particle size distribution of the impacted material similarly changes with velocity/peak shock pressure. -The experiments described above are designed to measure the near- to mid-IR effects from these changes to the mineral structure. See Lederer et al., this meeting for additional experimental results.

Jensen, E.↗
NASA NTRS1990

The sound of moving bodies

The importance of the quadrupole source term in the Ffowcs, Williams, and Hawkings (FWH) equation was addressed. The quadrupole source contains fundamental components of the complete fluid mechanics problem, which are ignored only at the risk of error. The results made it clear that any application of the acoustic analogy should begin with all of the source terms in the FWH theory. The direct calculation of the acoustic field as part of the complete unsteady fluid mechanics problem using CFD is considered. It was shown that aeroelastic calculation can indeed be made with CFD codes. The results indicate that the acoustic field is the most susceptible component of the computation to numerical error. Therefore, the ability to measure the damping of acoustic waves is absolutely essential both to develop acoustic computations. Essential groundwork for a new approach to the problem of sound generation by moving bodies is presented. This new computational acoustic approach holds the promise of solving many problems hitherto pushed aside.

Brentner, Kenneth Steven↗
NASA NTRS1994

Semiclassical Study of the Wave Vector Dependence of the Interband Impact Ionization Rate in Bulk Silicon

We present calculations of the interband impact ionization rate calculated using a wave vector dependent (k-dependent) semiclassical formulation of the transition rate. The transition rate is determined using Fermi's golden rule from a two-body screened Coulomb interaction assuming energy and momentum conservation. The transition rate is calculated for the first two conduction bands of silicon by numerically integrating over the full Brillouin zone. The overlap integrals in the expression for the transition rate are determined numerically using a 15 band k-p calculation. It is found that the transition rate depends strongly on the initiating electron wave vector (k vector) and that the transition rate is greatest for electrons originating within the second conduction band than the first conduction band. An ensemble Monte Carlo simulation, which includes the numerically determined ionization transition rate as well as the full details of the first two conduction bands, is used to calculate the total impact ionization rate in bulk silicon. Good agreement with the experimentally determined electron ionization rate data is obtained.

Wang, Yang↗
NASA NTRS1992

Finite-difference algorithms for the time-domain Maxwell's equations - A numerical approach to RCS analysis

The applications of two CFD-based finite-difference methods to computational electromagnetics are investigated. In the first method, the time-domain Maxwell's equations are solved using the explicit Lax-Wendroff scheme and in the second method, the second-order wave equations satisfying the Maxwell's equations are solved using the implicit Crank-Nicolson scheme. The governing equations are transformed to a generalized curvilinear coordinate system and solved on a body-conforming mesh using the scattered-field formulation. The induced surface current and the bistatic radar cross section are computed and the results are validated for several two-dimensional test cases involving perfectly-conducting scatterers submerged in transverse-magnetic plane waves.

Vinh, Hoang↗
NASA NTRS1999

Sonic Boom Prediction and Minimization of the Douglas Reference OPT5 Configuration

Conventional CFD methods and grids do not yield adequate resolution of the complex shock flow pattern generated by a real aircraft geometry. As a result, a unique grid topology and supersonic flow solver was developed at Northrop Grumman based on the characteristic behavior of supersonic wave patterns emanating from the aircraft. Using this approach, it was possible to compute flow fields with adequate resolution several body lengths below the aircraft. In this region, three-dimensional effects are diminished and conventional two-dimensional modified linear theory (MLT) can be applied to estimate ground pressure signatures or sonic booms. To accommodate real aircraft geometries and alleviate the burdensome grid generation task, an implicit marching multi-block, multi-grid finite-volume Euler code was developed as the basis for the sonic boom prediction methodology. The Thomas two-dimensional extrapolation method is built into the Euler code so that ground signatures can be obtained quickly and efficiently with minimum computational effort suitable to the aircraft design environment. The loudness levels of these signatures can then be determined using a NASA generated noise code. Since the Euler code is a three-dimensional flow field solver, the complete circumferential region below the aircraft is computed. The extrapolation of all this field data from a cylinder of constant radius leads to the definition of the entire boom corridor occurring directly below and off to the side of the aircraft's flight path yielding an estimate for the entire noise "annoyance" corridor in miles as well as its magnitude. An automated multidisciplinary sonic boom design optimization software system was developed during the latter part of HSR Phase 1. Using this system, it was found that sonic boom signatures could be reduced through optimization of a variety of geometric aircraft parameters. This system uses a gradient based nonlinear optimizer as the driver in conjunction with a computationally efficient Euler CFD solver (NIIM3DSB) for computing the three-dimensional near-field characteristics of the aircraft. The intent of the design system is to identify and optimize geometric design variables that have a beneficial impact on the ground sonic boom. The system uses a simple wave drag data format to specify the aircraft geometry. The geometry is internally enhanced and analytic methods are used to generate marching grids suitable for the multi-block Euler solver. The Thomas extrapolation method is integrated into this system, and hence, the aircraft's centerline ground sonic boom signature is also automatically computed for a specified cruise altitude and yields the parameters necessary to evaluate the design function. The entire design system has been automated since the gradient based optimization software requires many flow analyses in order to obtain the required sensitivity derivatives for each design variable in order to converge on an optimal solution. Hence, once the problem is defined which includes defining the objective function and geometric and aerodynamic constraints, the system will automatically regenerate the perturbed geometry, the necessary grids, the Euler solution, and finally the ground sonic boom signature at the request of the optimizer.

Siclari, Michael J.↗
NASA NTRSDate not supplied

Parameterized Study of Heat Load Trends in a Subscale Rotating Detonation Rocket Engine

NASA has developed a subscale rotating detonation rocket engine platform, enabling rapid parameterization of components and their associated performances. A major performance metric of interest for RDREs is the total heat absorbed at a given operating condition and wave mode operation. To investigate this, several sets of hardware were produced to have variation of the contraction ratio, injector geometry, and length. A wide range of total mass flow rates and mixture ratios were also explored using gaseous methane/oxygen. All hardware was produced using laser powder bed fusion GRCop-42, GRX-810, or C-103 alloys depending on the component cooling requirements. Outer and inner body hardware were made from GRCop-42 where heat fluxes were expected to be high and were water cooled through integrated coolant channels. Nozzles were made from C-103 which are radiatively cooled. Finally, the injectors were produced using GRCop-42 or GRX-810 as passive cooling via propellant injection has previously found to be sufficient given the small gap width of exposed injection surface. Total heat load and bulk heat flux measurements to the hot walls are reported. Trends in heat load and heat flux are shown with relation to parameters such as chamber pressure, area ratio, and wave mode. Heat loads between the inner and outer bodies and the chamber and shroud section are compared.

Heat Flux↗
NASA NTRSDate not supplied

Parameterized Study of Heat Load Trends in a Subscale Rotating Detonation Rocket Engine

NASA has developed a subscale rotating detonation rocket engine platform, enabling rapid parameterization of components and their associated performances. A major performance metric of interest for RDREs is the total heat absorbed at a given operating condition and wave mode operation. To investigate this, several sets of hardware were produced to have variation of the contraction ratio, injector geometry, and length. A wide range of total mass flow rates and mixture ratios were also explored using gaseous methane/oxygen. All hardware was produced using laser powder bed fusion GRCop-42, GRX-810, or C-103 alloys depending on the component cooling requirements. Outer and inner body hardware were made from GRCop-42 where heat fluxes were expected to be high and were water cooled through integrated coolant channels. Nozzles were made from C-103 which are radiatively cooled. Finally, the injectors were produced using GRCop-42 or GRX-810 as passive cooling via propellant injection has previously found to be sufficient given the small gap width of exposed injection surface. Total heat load and bulk heat flux measurements to the hot walls are reported. Trends in heat load and heat flux are shown with relation to parameters such as chamber pressure, area ratio, and wave mode. Heat loads between the inner and outer bodies and the chamber and shroud section are compared.

Heat Loads↗
NASA NTRS1984

Research in millimeter wave techniques

Work on the development of an improved 183 GHz subharmonic mixer was concentrated in two areas. First, there was an improved performance from current mixer body designs by testing different diodes and varying the whisker lengths. Second, there is the design of a new body structure. The whisker and diode pinsare in the same piece of the mixer that holds the substrate, reducing any motion of the parts that form the ohmic contacts of the diodes circuit. The broadband, low loss, quasi-optical diplexer, which is designed for use with a single ended mixer, has been developed. It uses a Gaussian beam waveguide as its transmission medium. The difference between the diplexer and other diplexers is the use of a Fabry Perot parallel plate filter. One is a multichannel radiometer system. Another approach is a quasi-optical RF polarization diplexer and another receiver. Some of the receivers developed were flown in aircraft and degraded considerably because of an LO failure. A technique for adding a 118 GHz channel to the existing Atmospheric Moisture Microwave Scanner radiometer system, using the RF diplexing scheme, is presented.

Forsythe, R. E.↗
NASA NTRS1980

Sound transmission into a laminated composite cylindrical shell

In the context of the transmission of airborne noise into an aircraft fuselage, a mathematical model is presented for the transmission of an oblique plane sound wave into a laminated composite circular cylindrical shell. Numerical results are obtained for geometry typical of a narrow-bodied jet transport. Results indicate that from the viewpoint of noise attenuation on laminated composite shell does not appear to offer any significant advantage over an aluminum shell. However, the transmission loss of a laminated composite shell is sensitive to the orientation of the fibers and this suggests the possibility of using a laminated composite shell to tailor the noise attenuation characteristics to meet a specific need.

Koval, L. R.↗
NASA NTRS1982

Implantable telemetry for small animals

A series of totally implantable telemetry devices for use in measuring deep body parameters in small animals were developed. Under a collaborative agreement with NASA, several of these systems; the continuous wave Doppler ultrasonic flowmeter, the multichannel telemetry system, and the inductively-powered dual channel cardiac pacer were evaluated in a series of ten mongrel dogs (15 to 20 kg.). These systems were used to measure ascending aortic and coronary blood flow, aortic pressure, and subcutaneous EKG.

Source record↗
NASA NTRS1985

Finite-amplitude steady waves in plane viscous shear flows

Computations of two-dimensional solutions of the Navier-Stokes equations are carried out for finite-amplitude waves on steady unidirectional flow. Several cases are considered. The numerical method employs pseudospectral techniques in the streamwise direction and finite differences on a stretched grid in the transverse direction, with matching to asymptotic solutions when unbounded. Earlier results for Poiseuille flow in a channel are re-obtained, except that attention is drawn to the dependence of the minimum Reynolds number on the physical constraint of constant flux or constant pressure gradient. Attempts to calculate waves in Couette flow by continuation in the velocity of a channel wall fail. The asymptotic suction boundary layer is shown to possess finite-amplitude waves at Reynolds numbers orders of magnitude less than the critical Reynolds number for linear instability. Waves in the Blasius boundary layer and unsteady Rayleigh profile are calculated by employing the artifice of adding a body force to cancel the spatial or temporal growth. The results are verified by comparison with perturbation analysis in the vicinity of the linear-instability critical Reynolds numbers.

Milinazzo, F. A.↗
NASA NTRS1955

Minimum-drag ducted and pointed bodies of revolution based on linearized supersonic theory

The linearized drag integral for bodies of revolution at supersonic speeds is presented in a double-integral form which is not based on slender-body approximations but which reduces to the equal slender-body expression in the proper limit. With the aid of a suitably chosen auxiliary condition, the minimum-external-wave-drag problem is solved for a transition section connecting two semi-infinite cylinders. The projectile tip is a special case and is compared with the Von Karman projectile tip. Calculations are presented which indicate that the method of analysis gives good first-order results in the moderate supersonic range.

Parker, Hermon M↗
NASA NTRS1960

The Blunt Plate In Hypersonic Flow

The sonic-wedge characteristics method has been used to obtain the shock shapes and surface pressure distributions on several blunt two-dimensional shapes in a hypersonic stream for several values of the ratio of specific heats. These shapes include the blunt slab at angle of attack and power profiles of the form yb = a)P, where 0 les than m less than 1, Yb and x are coordinates of the body surface, and a is a constant. These numerical results have been compared with the results of blast-wave theory, and methods of predicting the pressure distributions and shock shapes are proposed in each case. The effects of a free-stream conical-flow gradient on the pressure distribution on a blunt slab in hypersonic flow were investigated by the sonic-wedge characteristics method and were found to be sizable in many cases. Procedures which are satisfactory for reducing pressure data obtained in conical flows with small gradients are presented.

Baradell, Donald L.↗
NASA NTRS2005

DEVELOPMENT OF AN INFLIGHT COUNTERMEASURE TO MITIGATE POSTFLIGHT GAIT DYSFUNCTION

Following spaceflight crewmembers experience gait and postural instabilities due to inflight adaptive alterations in sensorimotor function. These changes can pose a risk to crew safety if nominal or emergency vehicle egress is required immediately following long-duration spaceflight. At present, no operational countermeasure is available to mitigate postflight locomotor disturbances. Therefore, the goal of this study is to develop an inflight training regimen that facilitates the recovery of locomotor function after long-duration spaceflight. The countermeasure we are developing is based on the concept of variable practice. During this type of training the subject gains experience producing the appropriate adaptive motor behavior under a variety of sensory conditions and response constraints. This countermeasure is built around current ISS treadmill exercise activities. Crewmembers will conduct their nominal inflight treadmill exercise while being exposed to variations in visual flow patterns. These variations will challenge the postural and locomotor systems repeatedly, thereby promoting adaptive reorganization in locomotor behavior. As a result of this training a subject learns to solve a class of motor problems, rather than a specific motor solution to one problem, Le., the subject learns response generalizability or the ability to "learn to learn" under a variety of environmental constraints. We anticipate that this training will accelerate recovery of postural and locomotor function during readaptation to gravitational environments following spaceflight facilitating neural adaptation to unit (Earth) and partial (Mars) gravity after long-duration spaceflight. The study calls for one group of subjects to perform the inflight treadmill training regimen while a control group of subjects performs only the nominal exercise procedures. Locomotor function in both groups is assessed before and after spaceflight using two tests of gait function: The Integrated Treadmill Locomotion Test (ITLT) and the Functional Mobility Test (FMT). The ITLT characterizes alterations in the integrated function of multiple sensorimotor subsystems responsible for the control of locomotion. This test calls for subjects to walk on a motorized treadmill while we assess changes in dynamic postural stability, head-trunk coordination, short-latency head stabilization responses, dynamic visual acuity, lower limb coordination strategies and gait cycle timing. To make these assessments we measure the following parameters while subjects walk on the treadmill: 1) full body 3-dimensional kinematics using a motion capture system (Motion Analysis Corp., Santa Rosa, CA); 2) the shock-wave transmitted from heel-strike to the head using triaxial accelerometers placed on the tibia and head (Entran, Fairfield, NJ); 3) vertical forces using an instrumented treadmill (Kistler Instrument Corp., Amherst, NY); 4) Dynamic visual acuity using Landolt Cs presented on a laptop computer located 4m from the eyes and 5) Gait cycle timing using foot-switches (Motion Lab Systems, Inc., Baton Rouge, LA) attached to the plantar surface of each shoe at the heel and toe. The FMT evaluates a subject's ability to perform challenging locomotor maneuvers similar to those encountered during an egress from a space vehicle. Subjects step over and duck under obstacles along with negotiating a series of pylons set up on a base of 10 cm thick medium density foam. The dependent measures for the FMT are time to complete the course and the number of obstacles touched. To date, we have collected pre and postflight locomotion data from Expeditions 5-9 who will serve as part of the control group for this study. Preliminary results comparing the recovery rates in gait control sub-systems obtained from the ITLT and FMT performance showed two recovery patterns: 1) a concordant recovery trend between gait control parameters and FMT performance indicating a restitution pattern of recovery and 2) gait controecovery that lagged recovery in FMT performance suggesting that improvement in locomotor function was attained through a pattern of substitution. These data suggest that recovery of postflight locomotor function may occur through adaptive mechanisms that lead to either restitution or substitution of function. Understanding the modes of postflight readaptation has implications for countermeasure development and testing and in astronaut postflight rehabilitation.

Bloomberg, J. J.↗
NASA NTRS2005

Development of an Inflight Countermeasure to Mitigate Postflight Gait Dysfunction

Following spaceflight crewmembers experience gait and postural instabilities due to inflight adaptive alterations in sensorimotor function. These changes can pose a risk to crew safety if nominal or emergency vehicle egress is required immediately following long-duration spaceflight. At present, no operational countermeasure is available to mitigate postflight locomotor disturbances. Therefore, the goal of this study is to develop an inflight training regimen that facilitates the recovery of locomotor function after long-duration spaceflight. The countermeasure we are developing is based on the concept of variable practice. During this type of training the subject gains experience producing the appropriate adaptive motor behavior under a variety of sensory conditions and response constraints. This countermeasure is built around current ISS treadmill exercise activities. Crewmembers will conduct their nominal inflight treadmill exercise while being exposed to variations in visual flow patterns. These variations will challenge the postural and locomotor systems repeatedly, thereby promoting adaptive reorganization in locomotor behavior. As a result of this training a subject learns to solve a class of motor problems, rather than a specific motor solution to one problem, Le., the subject learns response generalizability or the ability to "learn to learn" under a variety of environmental constraints. We anticipate that this training will accelerate recovery of postural and locomotor function during readaptation to gravitational environments following spaceflight facilitating neural adaptation to unit (Earth) and partial (Mars) gravity after long-duration spaceflight. The study calls for one group of subjects to perform the inflight treadmill training regimen while a control group of subjects performs only the nominal exercise procedures. Locomotor function in both groups is assessed before and after spaceflight using two tests of gait function: The Integrated Treadmill Locomotion Test (ITLT) and the Functional Mobility Test (FMT). The ITLT characterizes alterations in the integrated function of multiple sensorimotor subsystems responsible for the control of locomotion. This test calls for subjects to walk on a motorized treadmill while we assess changes in dynamic postural stability, head-trunk coordination, short-latency head stabilization responses, dynamic visual acuity, lower limb coordination strategies and gait cycle timing. To make these assessments we measure the following parameters while subjects walk on the treadmill: 1) full body 3-dimensional kinematics using a motion capture system (Motion Analysis Corp., Santa Rosa, CA); 2) the shock-wave transmitted from heel-strike to the head using triaxial accelerometers placed on the tibia and head (Entran, Fairfield, NJ); 3) vertical forces using an instumented treadmill (Kistler Instrument Corp., Amherst, NY); 4) Dynamic visual acuity using Landolt Cs presented on a laptop computer located 4m from the eyes and 5) Gait cycle timing using foot-switches (Motion Lab Systems, Inc., Baton Rouge, LA) attached to the plantar surface of each shoe at the heel and toe. The FMT evaluates s. subject's ability to perform challenging locomotor maneuvers similar to those encountered during an egress from a space vehicle. Subjects step over and duck under obstacles along with negotiating a series of pylons set up on a base of 10 cm thick medium density foam. The dependent measures for the FMT are time to complete the course and the number of obstacles touched. To date, we have collected pre and postflight locomotion data from Expeditions 5-9 who will serve as part of the control group for this study. Preliminary results comparing the recovery rates in gait control sub-systems obtained from the ITLT and FMT performance showed two recovery patterns: 1) a concordant recovery trend between gait control parameters and FMT performance indicating a restitution pattern of recovery and 2) gait controecovery that lagged recovery in FMT performance suggesting that improvement in locomotor function was attained through a pattern of substitution. These data suggest that recovery of postflight locomotor function may occur through adaptive mechanisms that lead to either restitution or substitution of function. Understanding the modes of postflight readaptation has implications for countermeasure development and testing and in astronaut postflight rehabilitation.

Bloomberg, J. J.↗