Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A Solution to Asymmetric Marangoni GTA Weld Behavior in a Dissimilar Chemistry Stainless Steel Joint [Slides]

Asymmetric and irregular weld morphology is an issue with the 9516 shipping container GTA weld. Observation of the weld puddle and cross sections showed the weld was biased toward the body side of the joint. This issue is attributed to a difference in the sulfur content and Marangoni fluid flow characteristics of the lid (150 ppm) and body (10 ppm) components of the weld joint. An additional contributing factor in this issue is the large difference in mass between the ½” thick lid and 1/8” thick body. A solution was developed comprised of a preliminary partial penetration weave pass across the joint intended to homogenize the sulfur content prior to the full penetration pass.

42 ENGINEERING↗
DOE OSTI2023

Impact of Plate Thickness and Joint Geometry on Residual Stresses in 347H Stainless Steel Welds

Weldments of 347H stainless steel are potentially susceptible to stress relaxation cracking at elevated service temperatures. Mitigation of stress relaxation cracking susceptibility within a multipass weld requires a good understanding of welding practices and manufacturing techniques to control high tensile residual stresses. Here in this work, the dependence of residual stress distribution in 347H stainless steel on base plate thickness, joint geometry design, and preheating condition was systematically investigated by using three-dimensional finite element models. The finite element models were validated through good agreement between neutron diffraction measurements and calculated elastic strains. The single-V-groove welds with and without a preheating step all produced similar peak von Mises residual stresses, above 450 MPa, within both the fusion zone and heat-affected zone (HAZ). In plates thicker than 0.5 in. (12.7 mm), high tensile residual stress could be observed in a relatively large area, from the middle of the plate thickness to underneath the top surface. A double-V groove shifted the high tensile stress area to the middle thickness of the weld. A single-J-groove weld was able to confine the residual stress to a very small region near the middle thickness within the fusion zone and suppressed the von Mises residual stress within the HAZ to below 400 MPa.

14 SOLAR ENERGY↗
DOE OSTI2025

Rotary Inertia Friction Welding of Dissimilar High-Strength 422 Martensitic Stainless Steel and 4140 Low Alloy Steel for Heavy-Duty Engine Piston Fabrication

AISI 422 martensitic stainless steel with superior high temperature performance (oxidation resistance and strength) is under evaluation for replacing current heavy-duty piston crown materials, AISI 4140 martensitic steel and micro alloyed steel (MAS) 38MnSiVS5, to fabricate a multimaterial piston. This multimaterial piston concept further improved power density and fuel economy by allowing heavyduty diesel engines to operate at higher temperatures and pressures. Joining AISI 422 steel piston crowns with AISI 4140 steel piston skirts is a key manufacturing step for this multimaterial piston. However, the significant differences in strength, elevated temperature flow stress, alloy chemistry, and temper resistance between these two martensitic steels cause some weldability issues (cracking) and metallurgical challenges (alloying element migration/segregation) when using conventional fusion-based welding processes. Rotary inertia friction welding (RIFW), a solid-state welding process, has been the preferred method to join 4140 crowns to 4140 skirts (and MAS crowns to MAS skirts) in high-volume production of current heavy-duty diesel engine pistons. It has been used to join these two materials with relatively comparable alloy chemistry to fabricate pistons with MAS skirts and 4140 crowns. Meanwhile, RIFW has also been a preferred method of dissimilar metal welding. However, RIFW of dissimilar high-strength martensitic steels has yet to be widely pursued. The interfacial microstructure complexities created by the thermomechanical process and highly nonequilibrium phase transformations during RIFW are a significant challenge for understanding and predicting their joining behavior and have not been reported in detail. Here, in this work, defect-free AISI 422 steel-AISI 4140 multimaterial pistons were successfully fabricated using the RIFW process. The interfacial microstructure and mechanical properties of dissimilar 422/4140 steel RIFW in the as-welded condition were experimentally studied in detail. The results provide critical baseline information for understanding RIFW mechanisms and guiding subsequent postweld heat treatment (PWHT) practice.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Analysis of the Fatigue Strength of Welds in Terms of Local Stress

A local approach is developed for calculating the fatigue strength of welded metal structures, selecting the basic weld structure, and identifying the group of welded structures corresponding to that basic structure. To that end, the stress state of typical welded structures is analyzed on the basis of two-level stress concentrators. The results may be used to develop standards for calculating the fatigue strength of welded metal structures.

42 ENGINEERING↗
DOE OSTI2014

Friction Stir Welding of Line-Pipe Steels

Friction stir welding (FSW) offers both economic and technical advantages over conventional fusion welding practices for welding line-pipe. For offshore line-pipe construction, the economic savings has been shown to be considerable, approaching a calculated 25%. Offshore pipe is relatively small diameter but heavy wall compared to onshore pipe. One concern is the ability to achieve consistent full weld penetration in an on-site offshore FSW operation, e.g., on a lay-barge. In addition, depending on the size and morphology of the unwelded zone, lack of penetration at the weld root can be difficult if not impossible to detect by conventional NDE methods. Thus, an approach to assure consistent full penetration via process control is required for offshore line-pipe construction using FSW. For offshore construction, an internal structural mandrel can be used offering the opportunity to use a sacrificial anvil FSW approach. With this approach, a small volume of sacrificial material can be inserted into the structural anvil. The FSW tool penetrates into the sacrificial anvil, beyond the inner diameter of the pipe wall, thus assuring full penetration. The sacrificial material is subsequently removed from the pipe inner wall. In the work presented herein, FSW studies were completed on both 6 mm and 12 mm wall thickness line-pipe. Lastly, post-FSW evaluations including radiography, root-bend tests, and metallography demonstrated the merits of the sacrificial anvil approach to achieve consistent full penetration.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2012

Influence of Alloy and Solidification Parameters on Grain Refinement in Aluminum Weld Metal due to Inoculation

The goals are: (1) Establish how much Ti/B grain refiner is need to completely refine aluminum weld metal for different alloys and different welding conditions; (2) Characterize how alloy composition and solidification parameters affect weld metal grain refinement; and (3) Apply relevant theory to understand observed behavior. Conclusions are: (1) additions of Ti/B grain refiner to weld metal in Alloys 1050, 5083, and 6082 resulted in significant grain refinement; (2) grain refinement was more effective in GTAW than LBW, resulting in finer grains at lower Ti content - reason is limited time available for equiaxed grain growth in LBW (inability to occlude columnar grain growth); (3) welding travel speed did not markedly affect grain size within GTAW and LBW clusters; and (4) application of Hunt CET analysis showed experimental G to be on the order of the critical G{sub CET}; G{sub CET} was consistently higher for GTAW than for LBW.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Implementation of ASME Code, Section XI, Code Case N-770, on Alternative Examination Requirements for Class 1 Butt Welds Fabricated with Alloy 82/182

In May 2010, the NRC issued a proposed notice of rulemaking that includes a provision to add a new section to its rules to require licensees to implement ASME Code Case N-770, ‘‘Alternative Examination Requirements and Acceptance Standards for Class 1 PWR Piping and Vessel Nozzle Butt Welds Fabricated with UNS N06082 or UNS W86182 Weld Filler Material With or Without the Application of Listed Mitigation Activities, Section XI, Division 1,’’ with 15 conditions. Code Case N-770 contains baseline and inservice inspection (ISI) requirements for unmitigated butt welds fabricated with Alloy 82/182 material and preservice and ISI requirements for mitigated butt welds. The NRC stated that application of ASME Code Case N-770 is necessary because the inspections currently required by the ASME Code, Section XI, were not written to address stress corrosion cracking Alloy 82/182 butt welds, and the safety consequences of inadequate inspections can be significant. The NRC expects to issue the final rule incorporating this code case into its regulations in the spring 2011 time frame. This paper discusses the new examination requirements, the conditions that NRC is imposing , and the major concerns with implementation of the new Code Case.

alloy 82/182↗
DOE OSTI2020

Process Development of the Vaporizing Foil Actuator Welding Technique

The industrial focus on continuous improvement for products is leading design engineers to consider multi-material design concepts more frequently. The design concepts use the advantages of each material while simultaneously minimizing the drawbacks. It also allows for the overall weight of the products to be reduced. Some traditional joining methods, though, struggle to join dissimilar material combinations. A technique known as vaporizing foil actuator welding, which was developed around ten years ago, is a solid-state joining method that has the potential to overcome the barriers to dissimilar material joining. The biggest drawbacks of vaporizing foil actuator welding are that it is still exclusively used in laboratory settings and early in the technology development process. As such, there is not enough confidence in the process for it to be transitioned to manufacturing environments yet. This work begins by analyzing the current state of the technology and identifying a roadmap to achieve a transition to manufacturing. The analysis found that increased confidence in the technology requires sample to sample repeatability to be improved. Beyond that, the process also needs to be fully automated before it can be considered as a viable technique for mass production. In order to further develop the technique, a fully automated work cell was constructed. By removing the human element from the process, this cell helped identify iii the aspects which contribute to process variability. The positioning of the vaporizing foil actuator was identified as the most important factor in process stability. A small set of samples were made in the automated cell with the addition of one component epoxy adhesive around the perimeter of the weld. These samples showed improved process repeatability compared with the samples made without adhesive. This indicates that small amounts of adhesive may be critical in using the process in industrial settings. Additionally, work was performed with manual positioning and adhesive dispensing. This work found that a hybrid joint behaves like traditional weld bonding, where the addition of adhesive makes the joint stronger than if either of the two joining methods were used on their own. To realize this performance with vaporizing foil actuator welding, though, the adhesive needs to be protected from burning during the rapid compression of air during the impact process.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Laser Welded Edge Seals for Polymer-Free Glass/Glass Modules

This presentation covers fs lasers which enable crack-free and stress-free glass/glass welds. Welds are nearly as strong as the glass (KI, weld ~ KI, glass) and static load test passed, enabling: 1) polymer-free; 2) hermetically sealed; and 3) recyclable modules. Next steps are: 1) follow-on funding; 2) develop feed throughs (metal/glass welds already achieved for other devices); and 3) weld mini modules for further IEC module testing.

DuraMAT↗
DOE OSTI2018

Remote In-bore Laser Cutting and Welding Tools for use in Future Nuclear Fusion Reactors - 18348

The maintenance, replacement and decommissioning of future nuclear fusion reactors will require quick and reliable cutting and joining of in-vessel pipework. Initial design studies for nuclear fusion reactors for power generation have estimated cutting and welding could account for up to 60% of the maintenance duration using conventional in-situ processing techniques (dry-mechanical cutting and arc welding) and that new methods are required to expedite the process. Additionally, the expected radioactivity and limited access at the cutting and welding sites mean that these processes cannot be done manually and robotic tools are required. To this end, remote in-bore laser cutting and welding tools have been developed for use in 90 mm internal diameter steel pipes. Here, we will present the designs of the remote in-bore laser cutting and welding tools, and how the tools fit within the overall remote maintenance strategy of a nuclear fusion reactor. Initial high-power laser trials were performed with prototype tools which successfully demonstrated their laser processing, thermal management and dust protection functionality. Although the tools described herein have been developed specifically for use within the fusion reactor environment, however the tool design and technology demonstrated here is readily transferable to many remote applications in challenging environments such as fission reactor maintenance, nuclear decommissioning and other in-accessible pipework. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

ELECTRIC FIELD-ASSISTED DIFFUSION WELDING TO FABRICATE ALLOY 617 COMPACT HEAT EXCHANGERS

Compact heat exchangers are of interest for a number of applications including advanced reactors. Alloy 617 is one of the top candidate materials for the gas-cooled reactor intermediate heat exchanger. Previous endeavors to diffusion weld Alloy 617 utilized hot pressing (HP). It was reported that grain boundary migration across the interface was hindered by extensive precipitation. Bonds of this nature have been observed to reduce the elevated-temperature mechanical properties compared to the wrought-product form. It was hypothesized that the electric current applied during electric-field-assisted sintering (EFAS) can overcome these challenges, resulting in improved diffusion welding (DW). This study investigated DW of Alloy 617 via EFAS. Stacks composed of three sheets that were 20 mm in diameter were welded using EFAS. Specimens were welded with an applied electric current, a pressure of 30 MPa, hold time of 30 min, and temperatures of 1050°C, 1100°C, and 1150°C. DW using HP as the zero-current analog of EFAS was also performed at the most promising EFAS conditions. Results revealed that both the applied electric current and temperature played a key role in precipitation and grain boundary migration in diffusion-welded Alloy 617. Precipitates were observed at the interface of the hot-pressed samples which limited grain boundary migration. Electric current was found to prevent precipitate formation along the interface at 1150°C. The electric current coupled with a temperature of 1150°C during EFAS resulted in significant grain boundary migration across the interface.

36 - MATERIALS SCIENCE↗
DOE OSTI2017

High performance computation of residual stress and distortion in laser welded 301L stainless sheets

Transient thermo-mechanical simulation of stainless plate laser welding process was performed by a highly efficient and accurate approach-hybrid iterative substructure and adaptive mesh method. Especially, residual stress prediction was enhanced by considering various heat effects in the numerical model. The influence of laser welding heat input on residual stress and welding distortion of stainless thin sheets were investigated by experiment and simulation. X-ray diffraction (XRD) and contour method were used to measure the surficial and internal residual stress respectively. Effect of strain hardening, annealing and melting on residual stress prediction was clarified through a parametric study. It was shown that these heat effects must be taken into account for accurate prediction of residual stresses in laser welded stainless sheets. Reasonable agreement among residual stresses by numerical method, XRD and contour method was obtained. Buckling type welding distortion was also well reproduced by the developed thermo-mechanical FEM.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fusion welding of refractory metals and ZrB 2 -SiC-ZrC ceramics

Molybdenum and a molybdenum alloy were fusion welded to ZrB2-based ceramics to determine if the electrical and thermal properties of the metals and ceramics affected their weldability. Commercial ceramic powders were hot pressed, machined into coupons, and preheated to 1600 °C before joining the ceramics to commercial metals using plasma arc welding. Weldability varied as indicated by the range of porosity observed within the fusion zones. Measured thermal and electrical properties appeared to have little to no effect on the weldability of metal-ceramic welds despite the large range of values measured across each property. Differences in melting temperatures between metal and ceramic coupons did affect weldability by changing the weld penetration depth into ceramic coupons. Finally, future studies on metal-ceramic welds are suggested to investigate the effect that work function, melt viscosity, wetting, or other properties have on weldability.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Analysis of attenuation data from the decommissioned ZIon unit 1 reactor pressure vessel beltline weld

In order to examine the attenuation of radiation damage through the thickness of an irradiated reactor pressure vessel (RPV), four segments were acquired from the Zion Unit 1 power plant RPV after the plant was decommissioned. The Zion Unit 1 RPV Beltline Weld Segment 1 was cut into seven blocks, consisting of five base metal and two beltline welds from the high fluence region of the segment. Through-wall test specimens were machined and tested. Specimens included those used for Charpy impact, Master Curve fracture toughness testing, and chemical analysis. The observed through-thickness ductile-to-brittle transition temperatures in the beltline weld deviated significantly from the expected behavior based on the attenuation of fast fluence as a function of depth into the RPV. Beginning at the inside surface, the 41-J Charpy transition temperature was either flat or slightly increasing until the ¾ -T location. The results of a simple, model-based analysis of the Zion beltline weld material that included the irradiation conditions and material chemistry were generally consistent with industry trend curves and the standard attenuation model, rather than the observed data. Although there was no archive material from the RPV available to permit measurement of the unirradiated properties, fracture toughness specimens fabricated from archive surveillance weld were used to obtain an estimate of the initial through-thickness values of the Charpy transition temperature. The Charpy shifts obtained using this approach were similarly in disagreement with the predictions of the US NRC Regulatory Guide 1.99, Rev. 2. However, testing of irradiated Charpy specimens taken from the RPV following post-irradiation annealing (10 hr. at 500 °C) provided a quite different estimate of the unirradiated properties which improved the agreement between the inferred through-thickness Charpy shifts and exponential attenuation model included in Regulatory Guide 1.99/2. In conclusion, the analysis of the Zion data and data obtained in previous post-mortem examinations of decommissioned RPVs indicates that more work is needed to understand the through-thickness properties of RPV materials in order to properly assess through-wall damage attenuation.

Charpy impact↗
DOE OSTI2014

Growth kinetics of Al–Fe intermetallic compounds during annealing treatment of friction stir lap welds

In this study, we explored the growth kinetics of the Al–Fe intermetallic (IM) layer at the joint interface of the St-12/Al-5083 friction stir lap welds during post-weld annealing treatment at 350, 400 and 450 °C for 30 to 180 min. Optical microscope (OM), field emission gun scanning electron microscope (FEG-SEM) and transmission electron microscope (TEM) were employed to investigate the structure of the weld zone. The thickness and composition of the IM layers were evaluated using image analysis system and electron back-scatter diffraction (EBSD), respectively. Moreover, kernel average misorientation (KAM) analysis was performed to evaluate the level of stored energy in the as-welded state. The results showed that the growth kinetics of the IM layer was not governed by a parabolic diffusion law. Presence of the IM compounds as well as high stored energy near the joint interface of the as-welded sample was recognized to be the origin of the observed deviation from the parabolic diffusion law. - Highlights: • This work provided a new insight into growth kinetics of Al–Fe IM thickness. • The growth kinetics of IM layer was not governed by a parabolic diffusion law. • IM near the joint interface was the origin of deviation from the parabolic law. • High stored energy at joint interface was origin of deviation from parabolic law.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure and mechanical behavior of laser remelted amorphous Al-Ni-La welds

To explore the feasibility of using laser powder bed fusion systems to print bulk amorphous Al alloys, a single autogenous weld produced by laser remelting on a cast Al-5La-9Ni (at.%) alloy was studied for its microstructure and mechanical behavior. The solidification rates experienced by material within the welds were high enough to produce entirely amorphous regions within the welds. Welds were characterized using SEM, STEM, and APT and were found to contain Ni-rich amorphous clusters. Micropillar compression tests were used to assess mechanical properties of the welds and found that all of the amorphous regions exhibited yield strengths around 1 GPa. In conclusion, these results are discussed in the context of diffusivity of Ni and rare earth elements in liquid, glass forming ability, thermodynamic driving force for phase formation during solidification, free volume concentrations in bulk metallic glasses, and cluster-related softening.

APT↗
DOE OSTI2014

Matrix phased array (MPA) imaging technology for resistance spot welds

A three-dimensional MPA probe has been incorporated with a high speed phased array electronic board to visualize nugget images of resistance spot welds. The primary application area of this battery operated portable MPA ultrasonic imaging system is in the automotive industry which a conventional destructive testing process is commonly adopted to check the quality of resistance spot welds in auto bodies. Considering an average of five-thousand spot welds in a medium size passenger vehicle, the amount of time and effort given to popping the welds and measuring nugget size are immeasurable in addition to the millions of dollars' worth of scrap metals recycled per plant per year. This wasteful labor intensive destructive testing process has become less reliable as auto body sheet metal has transitioned from thick and heavy mild steels to thin and light high strength steels. Consequently, the necessity of developing a non-destructive inspection methodology has become inevitable. In this paper, the fundamental aspects of the current 3-D probe design, data acquisition algorithms, and weld nugget imaging process are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Nondestructive Evaluation of Stress Corrosion Cracking in a Welded Steel Plate Using Guided Ultrasonic Waves

Stress corrosion cracking (SCC) had occurred in early-generation high-level nuclear waste tanks constructed by welding carbon steel. This paper describes an ultrasonic inspection system and its fundamental ability to detect and quantify the length of SCC on thick welded steel plates. The finite element method (FEM) was applied to simulate the welding process to estimate the welding residual stress field. Growth of stress corrosion cracks is driven by crack stress intensities exceeding the subcritical cracking threshold intensity. The subject plate was experimentally inspected with ultrasonic nondestructive evaluation (NDE) techniques to characterize the extent of SCC. The NDE system uses a piezoelectric transducer to generate guided waves in the thick steel plate, and a scanning laser Doppler vibrometer (SLDV) to measure multidimensional time–space wavefield data over a user-defined scanning area in the plate surface. The measured wavefield data can show wave interactions in a localized area in the plate due to the presence of the discontinuities of the SCC. To generate an inspection image that can precisely show the crack’s location and/or the dimension, the wavefield data are further processed to generate inspection image that maps the entire sample plate so the crack can be clearly identified in the plate while its length can be readily estimated. In conclusion, the ultrasonic test results for crack length agree well with the visually estimated length and are close to that predicted by the FEM for cracks in the weld residual stress field.

36 MATERIALS SCIENCE↗