Mesoscale Interrogation Reveals Mechanistic Origins of Lithium Filaments along Grain Boundaries in I
Explore the source record for details and available documents.
Vishnugopi, Bairav S.↗
SEARCH · Engineering Papers
Results for “Voids”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Investigation and Suppression of Oxygen Release by LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode under Overcharge Conditions
The safety issue of lithium-ion batteries is a crucial factor limiting their large-scale application. Therefore, it is of practical significance to evaluate the impact of their overcharge behavior because of the severe levels of oxygen release of cathode materials during this process. Here, by combining a variety of in situ techniques of spectroscopy and electron microscopy, this work studies the structural degradation of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) accompanying the oxygen release in the overcharge process. It is observed that a small amount of O 2 evolves from the initial surface at ≈4.7V. When charging to a higher voltage (≈5.5V), a large amount of O 2 evolves on the newly formed surface due to the occurrence of microcracks. Based on experimental results and theoretical calculations, it is determined that the oxygen release mainly occurs in the near-surface regions, where the remaining oxygen vacancies accumulate to create voids. To suppress the oxygen release, single-crystalline NCM811 with integrated structure is introduced and serves as a cathode, which can effectively inhibit morphology destruction and reduce the activation of lattice oxygen in the surface region. These findings provide a theoretical basis and effective strategy for improving the safety performance of Ni-rich cathode materials in practical applications.
25 ENERGY STORAGE↗
Unveiling the Mechanical and Electrochemical Evolution of Nanosilicon Composite Anodes in Sulfide-Based All-Solid-State Batteries
The utilization of silicon anodes in all-solid-state lithium batteries provides good prospects for facilitating high energy density. However, the compatibility of sulfide solid-state electrolytes (SEs) with Si and carbon is often questioned due to potential decomposition. Here, in this paper, operando X-ray absorption near-edge structure (XANES) spectroscopy, ex situ scanning electron microscopy (SEM), and ex situ X-ray nanotomography (XnT) are utilized to investigate the chemistry and structure evolution of nano-Si composite anodes. Results from XANES demonstrate a partial decomposition of SEs during the first lithiation stage, which is intensified by the presence of carbon. Nevertheless, the performances of first three cycles in Si–SE–C are stable, which proves that the generated media is ionically conductive. XnT and SEM results show that the addition of SEs and carbon improves the structural stability of the anode, with fewer pores and voids. A chemo-elasto-plastic model reveals that SEs and carbon buffer the volume expansion of Si, thus enhancing mechanical stability. The balance between the pros and cons of SEs and carbon in enhancing reaction kinetics and structural stability enables the Si composite anode to demonstrate the highest Si utilization with higher specific capacities and a better rate than pure Si and Si composite anodes with only SEs.
36 MATERIALS SCIENCE↗
Accelerated Short Circuiting in Anode-Free Solid-State Batteries Driven by Local Lithium Depletion
“Anode-free” solid-state batteries (SSBs), which have no anode active material, can exhibit extremely high energy density (≈1500 Wh L -1 ). However, there is a lack of understanding of the lithium plating/stripping mechanisms at initially lithium-free solid-state electrolyte (SSE) interfaces because excess lithium metal is often used. Here, it is demonstrated that commercially relevant quantities of lithium (>5 mAh cm -2 ) can be reliably plated at moderate current densities (1 mA cm -2 ) using the sulfide SSE Li 6 PS 5 Cl. Investigations of lithium plating/stripping mechanisms, in conjunction with cryo-ocused ion beam (FIB) imaging, synchrotron tomography, and phase-field modeling, reveal that the cycling stability of these cells is fundamentally limited by the nonuniform presence of lithium during stripping. Local lithium depletion causes isolated lithium regions toward the end of stripping, decreasing electrochemically active area and resulting in high local current densities and void formation. This accelerates subsequent filament growth and short circuiting compared to lithium-excess cells. Despite this degradation mode, here it is shown that anode-free cells exhibit comparable Coulombic efficiency to lithium-excess cells, and improved resistance to short circuiting is achieved by avoiding local lithium depletion through retention of thicker lithium at the interface. These new insights provide a foundation for engineering future high-energy anode-free SSBs.
25 ENERGY STORAGE↗
Mechanical Milling – Induced Microstructure Changes in Argyrodite LPSCl Solid-State Electrolyte Critically Affect Electrochemical Stability
Microstructure of argyrodite solid-state electrolyte (SSE) critically affects lithium metal electrodeposition/dissolution. While the stability of unmodified SSE is mediocre, once optimized state-of-the-art electrochemical performance is achieved (symmetric cells, full cells with NMC811) without secondary interlayers or functionalized current collectors. Planetary mechanical milling in wet media (m-xylene) is employed to alter commercial Li 6 PS 5 Cl (LPSCl) powder. Quantitative stereology demonstrates how milling progressively refines grain and pore size/distribution in the SSE compact, increases its density, and geometrically smoothens the SSE-Li interface. Mechanical indentation demonstrates that these changes lead to reduced site-to-site variation in the compact's hardness. Milled microstructures promote uniform early-stage electrodeposition on foil collectors and stabilize solid electrolyte interphase (SEI) reactivity. Analysis of half-cells with bilayer electrolytes demonstrates the importance of microstructure directly contacting current collector, with interface roughness due to pore and grain size distribution being key. For the first time, short-circuiting Li metal dendrite is directly identified, employing 1.5 mm diameter “mini” symmetrical cell and cryogenic focused ion beam (cryo-FIB) electron microscopy. The branching sheet-like dendrite traverses intergranularly, filling the interparticle voids and forming an SEI around it. Importantly, mesoscale modeling reveals the relationship between Li-SSE interface morphology and the onset of electrochemical instability, based on underlying reaction current distribution.
25 ENERGY STORAGE↗
Operando Investigation on the Role of Densification and Chemo-Mechanics on Solid-State Cathodes
All solid-state batteries are desirable for a range of energy storage applications which require high energy density. Achieving a high energy density in a solid-state battery requires the operation of an energy dense anode with a composite solid-state cathode. Pores and/or voids within a solid state cathode are ion-blocking and thus control over the concentration and distribution of pores in the initial electrode and cycled electrode is desirable. This study provides an understanding of the interplay between electrode microstructure and mechanics on active material utilization in solid state cathodes composed of NCM 811 and Li 6 PS 5 Cl. Decreasing the solid electrolyte particle size leads to greater active material-electrolyte contact and less total deformation when exposed to an external load. Composite cathodes with greater compliance can potentially decrease strain between the active material and solid electrolyte, decrease delamination events and result in higher overall active material utilization and high capacity retention.
25 ENERGY STORAGE↗
Evaluating Pressure‐dependent Discharge Behavior of Foil Versus In situ Plated Lithium Metal Anodes in Solid‐State Batteries
Abstract Anode‐free manufacturing of solid‐state batteries (SSBs) shows promise to maximize energy density by eliminating excess lithium (Li) and simplifying battery production. However, high reversibility during discharge (stripping of Li) is necessary for long‐lifetime SSBs with a limited Li reservoir. Further, the plastic flow of Li changes depending on the Li thickness, leading to possible differences in discharge performance under stack pressure. This work investigates the pressure‐dependent discharge performance of anode‐free manufactured SSBs with in situ plated Li and compares the performance to that of conventional thick Li foil cells. Distinct stripping behavior is observed at low pressures (0–1 MPa), where Li diffusivity and initial interfacial contact may control accessible capacity, compared to high pressures (3–10 MPa) where mechanical deformation of Li likely governs stripping behavior. Analysis of impedance spectra collected during stripping shows that additional stack pressure delays the formation of deep, as opposed to lateral, voids in the Li anode. These results provide insights to guide the transition from thick Li foil anodes to anode‐free manufactured SSBs.
Haslam, Catherine G.↗
Quantifying the impact of temporal analysis of products reactor initial state uncertainties on kinetic parameters
The temporal analysis of products (TAP) reactor, a transient kinetic tool, provides users with information as the catalyst state evolves. However, the state of the art for TAP uncertainty quantification only considers the experimental noise present in the outlet flow signal. Additional sources of uncertainty, including, but not limited to, initial surface coverages, the catalyst zone location, the inert void fraction, and the gas pulse intensity and pulse delay, are not included. For this reason, a framework for quantifying all uncertainty sources present in TAP experiments is presented and applied to a carbon monoxide oxidation case study. Herein, two methods for quantifying these sources of uncertainty are introduced. The first utilizes initial state sensitivities to approximate the parameter variances, as well as to provide insights into the structural certainty of the model. The second generates parameter confidence distributions through an ensemble-based sampling algorithm. This initial state covariance matrix can ultimately be merged with the experimental noise covariance matrix, providing a unified description of the parameter uncertainties for a single TAP experiment.
36 MATERIALS SCIENCE↗
Observation of Ion Electrosorption in Metal–Organic Framework Micropores with In Operando Small-Angle Neutron Scattering
A molecular-level understanding of transport and adsorption mechanisms of electrolyte ions in nanoporous electrodes under applied potentials is essential to control the performance of double-layer capacitors. In this paper, in operando small-angle neutron scattering (SANS) is used to directly detect ion movements into the nanopores of a conductive metal–organic framework (MOF) electrode under operating conditions. Neutron-scattering data reveals that most of the void space within the MOF is accessible to the solvent. Upon the addition of the electrolyte sodium triflate (NaOTf), the ions are adsorbed on the outer surface of the protrusions to form a 30 Å layer instead of entering the ionophobic pores in the absence of an applied charging potential. The changes in scattering intensity when potentials are applied suggests the ion rearrangement in the micropores following different mechanisms depending on the electrode polarization. These observations shed insights on ion electrosorption in electrode materials.
36 MATERIALS SCIENCE↗
Enhanced Reactivity of Accessible Protons in Sodalite Cages of Faujasite Zeolite
Abstract Faujasite (FAU) zeolites (with Si/Al ratio of ca. 1.7) undergo mild dealumination at moderate ion exchange conditions (0.01 to 0.6 M of NH 4 NO 3 solutions) resulting in protons circumscribed by sodalite cages becoming accessible for reaction without conspicuous changes to bulk crystallinity. The ratio of protons in sodalite cages (H SOD ) to supercages (H SUP ) can be systematically manipulated from 0 to ca. 1 by adjusting ammonium concentrations used in ion exchange. The fraction of accessible protons in the sodalite cages is assessed by virtue of infrared spectra for H‐D exchange of deuterated propane based on the band area ratio of OD 2620 /OD 2680 (OD SOD /OD SUP ). Protons in sodalite cages (H SOD ) show higher rate constants of propane dehydrogenation ( k D ) and cracking ( k C ) than protons in supercages (H SUP ) plausibly due to confinement effects being more prominent in smaller voids. Rate constants of dehydrogenation and cracking including k D / k C ratios are also augmented as the fraction of accessible protons in the sodalite cages is enhanced. These effects of accessibility and reactivity of protons in sodalite cages hitherto inconspicuous are revealed herein via methods that systematically increase accessibility of cations located in sodalite cages.
Li, Xinyu↗
Influence of Potassium Metal‐Support Interactions on Dendrite Growth
Abstract Combined synchrotron X‐ray nanotomography imaging, cryogenic electron microscopy (cryo‐EM) and modeling elucidate how potassium (K) metal‐support energetics influence electrodeposit microstructure. Three model supports are employed: O‐functionalized carbon cloth (potassiophilic, fully‐wetted), non‐functionalized cloth and Cu foil (potassiophobic, nonwetted). Nanotomography and focused ion beam (cryo‐FIB) cross‐sections yield complementary three‐dimensional (3D) maps of cycled electrodeposits. Electrodeposit on potassiophobic support is a triphasic sponge, with fibrous dendrites covered by solid electrolyte interphase (SEI) and interspersed with nanopores (sub‐10 nm to 100 nm scale). Lage cracks and voids are also a key feature. On potassiophilic support, the deposit is dense and pore‐free, with uniform surface and SEI morphology. Mesoscale modeling captures the critical role of substrate‐metal interaction on K metal film nucleation and growth, as well as the associated stress state.
Liu, Pengcheng↗
Tighter Confinement Increases Selectivity of d-Glucose Isomerization Toward l-Sorbose in Titanium Zeolites
Aqueous-phase isomerization of D-glucose to D-fructose and L-sorbose is catalyzed in parallel by Lewis acidic Ti sites in siliceous frameworks. Glucose isomerization rates (per Ti, 373 K) are undetectable when Ti sites are confined within mesoporous voids (Ti-MCM-41, TiO 2 -SiO 2 ) and increase to detectable values when Ti sites are confined within the smaller 12-membered ring (12-MR) micropores of Ti-Beta. Furthermore, isomerization rates decrease to lower values (by ≈20×) with further decreases in micropore size as Ti sites are confined within 10-MR pores (Ti-MFI, Ti-CON), likely because of intrapore reactant diffusion restrictions, and reach undetectable values within the 8-MR pores of Ti-CHA as size exclusion prevents glucose from accessing active sites. Remarkably, the selectivity toward l -sorbose over d -fructose increases systematically as spatial constraints around Ti sites become tighter, and is >10 on Ti-MFI. These findings demonstrate the marked influence of confinement around Ti active sites on the selectivity between parallel stereoselective sugar isomerization pathways.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Enhanced Reactivity of Accessible Protons in Sodalite Cages of Faujasite Zeolite
We report Faujasite (FAU) zeolites (with Si/Al ratio of ca. 1.7) undergo mild dealumination at moderate ion exchange conditions (0.01 to 0.6 M of NH 4 NO 3 solutions) resulting in protons circumscribed by sodalite cages becoming accessible for reaction without conspicuous changes to bulk crystallinity. The ratio of protons in sodalite cages (H SOD ) to supercages (H SUP ) can be systematically manipulated from 0 to ca. 1 by adjusting ammonium concentrations used in ion exchange. The fraction of accessible protons in the sodalite cages is assessed by virtue of infrared spectra for H-D exchange of deuterated propane based on the band area ratio of OD 2620 /OD 2680 (OD SOD /OD SUP ). Protons in sodalite cages (H- SOD ) show higher rate constants of propane dehydrogenation (k D ) and cracking (k C ) than protons in supercages (H SUP ) plausibly due to confinement effects being more prominent in smaller voids. Rate constants of dehydrogenation and cracking including k D /k C ratios are also augmented as the fraction of accessible protons in the sodalite cages is enhanced. These effects of accessibility and reactivity of protons in sodalite cages hitherto inconspicuous are revealed herein via methods that systematically increase accessibility of cations located in sodalite cages.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Influence of Potassium Metal-Support Interactions on Dendrite Growth
We report combined synchrotron X-ray nanotomography imaging, cryogenic electron microscopy (cryo-EM) and modeling elucidate how potassium (K) metal-support energetics influence electrodeposit microstructure. Three model supports are employed: O-functionalized carbon cloth (potassiophilic, fully-wetted), non-functionalized cloth and Cu foil (potassiophobic, nonwetted). Nanotomography and focused ion beam (cryo-FIB) cross-sections yield complementary three-dimensional (3D) maps of cycled electrodeposits. Electrodeposit on potassiophobic support is a triphasic sponge, with fibrous dendrites covered by solid electrolyte interphase (SEI) and interspersed with nanopores (sub-10 nm to 100 nm scale). Lage cracks and voids are also a key feature. On potassiophilic support, the deposit is dense and pore-free, with uniform surface and SEI morphology. Mesoscale modeling captures the critical role of substrate-metal interaction on K metal film nucleation and growth, as well as the associated stress state.
36 MATERIALS SCIENCE↗
On the Electride Nature of Na–hP4
Early quantum mechanical models suggested that pressure drives solids towards free-electron metal behavior where the ions are locked into simple close-packed structures. The prediction and subsequent discovery of high-pressure electrides (HPEs), compounds assuming open structures where the valence electrons are localized in interstitial voids, required a paradigm shift. Our quantum chemical calculations on the iconic insulating Na-hP4 HPE show that increasing density causes a 3s→3pd electronic transition due to Pauli repulsion between the 1s2s and 3s states, and orthogonality of the 3pd states to the core. The large lobes of the resulting Na-pd hybrid orbitals point towards the center of an 11-membered penta-capped trigonal prism and overlap constructively, forming multicentered bonds, which are responsible for the emergence of the interstitial charge localization in Na-hP4. As a result, these multicentered bonds facilitate the increased density of this phase, which is key for its stabilization under pressure.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
PDMS ‐silica composite gas separation membranes by direct ink writing
Abstract Polydimethylsiloxane (PDMS)‐based membranes containing amine‐functionalized and unfunctionalized silica particles were fabricated via direct ink writing for CO 2 /N 2 gas separation. The printability of the inks was evaluated by rheological measurements, while spectroscopy, microscopy, thermal measurements, and mechanical testing were employed to characterize the printed membranes. The surface morphology of the membranes revealed the absence of voids, demonstrating their suitability for gas separation. The printed membranes also exhibited desirable thermal and mechanical properties (i.e., thermal degradation temperature of 518 °C and tensile strength as high as 1.178 MPa with 529% elongation). The PDMS‐based membranes generally displayed high permeability for CO 2 but slightly low selectivity for the CO 2 /N 2 gas pair. The best‐combined permeability‐selectivity performance of 8794 barrer and selectivity of 11.64 was demonstrated by the printed PDMS membrane containing no SiO 2 fillers. The inclusion of unfunctionalized SiO 2 particles generally increased the membrane's gas permeability but compromised the selectivity. In contrast, membranes with amine‐functionalized silica showed improved selectivity compared to membranes containing unfunctionalized silica. Overall, the performance and characteristics offered by the PDMS/silica composite membranes demonstrated the potential of 3D printing as an economical and sustainable fabrication approach to developing materials for carbon capture applications.
Gutierrez, Dianne B.↗
Consequences of Intrapore Liquids on Reactivity, Selectivity, and Stability for Aldol Condensation Reactions on Anatase TiO 2 Catalysts
Abstract This study provides evidence and mechanistic interpretations for the significant consequences of intrapore non‐polar liquids on acetone aldol condensation turnover rates, selectivity to primary dimer products, and catalyst stability for reactions at Lewis acid‐base site pairs on TiO 2 surfaces. These non‐polar liquids confer such benefits through the preferential stabilization of transition states (TS) for adsorption (“entry”) and desorption (“exit”) steps, which place their respective reactants or products within a solvating outer sphere environment. The extent to which non‐polar fluids ( n ‐heptane) form an intrapore liquid phase within TiO 2 voids was obtained from N 2 uptakes using established formalisms that consider the different molal volume, surface tension, and volatility between N 2 and n ‐heptane. Acetone condensation rates are limited by C−H activation, an “entry” step that forms bound prop‐1‐en‐2‐olates via a TS stabilized by intrapore liquids, leading to higher aldol condensation turnover rates as n ‐heptane pressure increases and active TiO 2 surfaces become increasingly immersed within a non‐polar liquid phase. These liquids solvate the late TS structures that mediate the desorption of primary C 6 condensation products even more effectively than those involved in prop‐1‐en‐2‐olate formation or in nucleophilic attack events that later form C−C bonds. Such preferential solvation favors desorption over C−C coupling events, thus disfavoring the formation of larger oligomers that become stranded at active sites, thus leading to much slower deactivation. Moreover, solvation by non‐polar liquids also leads to C 6 alkanones as the sole products formed in a single surface sojourn. These effects of a non‐polar dense phase circumvent the inherent stability, reactivity, and selectivity hurdles that have precluded practical aldol condensation catalysis on Lewis acid‐base pairs at oxide surfaces; these consequences are demonstrated here for TiO 2 catalysts, acetone aldol condensation reactions, and n ‐heptane as the non‐polar liquid but through strategies, concepts, and mechanistic features that extend to other systems. More generally, these observations and their mechanistic origins demonstrate how a contacting liquid preferentially solvates TS structures for elementary steps that involve either reactants arriving from or products entering into an outer sphere environment that contains a dense non‐polar phase.
Kadam, Shashikant A.↗
Thermal conductivity of salvaged fused cast alumina used in the glass industry
Fused cast alumina (FCA) has been and continues to be used as a refractory material in energy intensive industries such as glass melting and chemical processing. In-service degradation due to high temperature exposure in harsh environment affects the designed furnace thermal profiles and energy consumption. Phase transformation may occur at the refractory hot face during glass melting altering the properties. Three FCA blocks recovered from industrial furnaces were investigated in this study. The as-received FCA consists primarily of a mixture of alpha (α) and beta (β) alumina that has a thermal conductivity value of 5–6 W/mK. The Hot Disk method was used to obtain thermal conductivity directly on the refractory blocks. At the hot face, a transformation from β to α alumina occurred and was confirmed by an X-ray diffraction study. Thermal conductivity measurements as a function of position also showed a clear transition from β to α alumina at both ends of a complete block with no voids. Thermal conductivity of the α alumina tripled compared to β alumina. This study provides important information of heat transfer and thermal conductivity evolution to refractory manufacturers and users.
36 MATERIALS SCIENCE↗