Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VELOCITY MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Fuel spray diagnostics

Several laser measurement methods are being studied to provide the capability to make droplet size and velocity measurements under a variety of spray conditions. The droplet sizing interferometer (DSI) promises to be a successful technique because of its capability for rapid data acquisition, compilation and analysis. Its main advantage is the ability to obtain size and velocity measurements in air-fuel mixing studies and hot flows. The existing DSI at NASA Lewis is a two-color, two-component system. Two independent orthogonal measurements of size and velocity components can be made simultaneously. It also uses an off-axis large-angle light scatter detection. The fundamental features of the system are optics, signal processing and data management system. The major component includes a transmitter unit, two receiver units, two signal processors, two data management systems, two Bragg cell systems, two printer/plotters, a laser, power supply and color monitor.

Bosque, M. A.↗

Progress on a Rayleigh Scattering Mass Flux Measurement Technique

A Rayleigh scattering diagnostic has been developed to provide mass flux measurements in wind tunnel flows. Spectroscopic molecular Rayleigh scattering is an established flow diagnostic tool that has the ability to provide simultaneous density and velocity measurements in gaseous flows. Rayleigh scattered light from a focused 10 Watt continuous-wave laser beam is collected and fiber-optically transmitted to a solid Fabry-Perot etalon for spectral analysis. The circular interference pattern that contains the spectral information that is needed to determine the flow properties is imaged onto a CCD detector. Baseline measurements of density and velocity in the test section of the 15 cm x 15 cm Supersonic Wind Tunnel at NASA Glenn Research Center are presented as well as velocity measurements within a supersonic combustion ramjet engine isolator model installed in the tunnel test section.

Mielke-Fagan, Amy F.↗

Plate motion in sheared granular fault system

Plate motion near the fault gouge layer, and the elastic interplay between the gouge layer and the plate under stick-slip conditions, is key to understanding the dynamics of sheared granular fault systems. Here, a two-dimensional implementation of the combined finite-discrete element method (FDEM), which merges the finite element method (FEM) and the discrete element method (DEM), is used to explicitly simulate a sheared granular gouge fault system. In this work we focus on investigating the influence of normal load, driving shear velocity and plate stiffness on the velocities and displacements in the direction parallel to the shear direction (x-direction) measured at locations on the upper and lower plates just adjacent to the gouge. The simulations show that during slip phases the magnitudes of the measured velocities on the upper and lower plates are proportional to the normal load and may be inversely proportional to the square root of the plate's shear modulus. Whereas, the driving shear velocity does not show distinct influence on the measured velocities. Additionally, large slip velocities are generally associated with large macroscopic friction coefficient drops. For the models subjected to smaller normal loads, larger shear velocities and with stiffer shear plates, the same magnitude of slip velocity could cause a larger drop of macroscopic friction coefficient. During stick phases, the velocities of the upper and lower plates are respectively slightly greater and slightly smaller than half of the driving shear velocity and are both in the same direction of shear. The shear strain rate of the gouge is calculated from this velocity difference between the upper and lower plate during stick phases and thus the gouge effective shear modulus can be calculated. The results show that the gouge effective shear modulus increases proportionally with normal load, while the influence of shear velocity and plate stiffness on gouge effective shear modulus is minor. The simulations address the dynamics of a laboratory-scale fault gouge system and may aid in revealing the complexities of earthquake frictional dynamics.

58 GEOSCIENCES↗

WIYN open cluster study. LIX. Radial velocity membership of the evolved population of the old open cluster NGC 6791

The open cluster NGC 6791 has been the focus of much recent study due to its intriguing combination of old age and high metallicity (∼8 Gyr, [Fe/H] = +0.30), as well as its location within the Kepler field. As part of the WIYN Open Cluster Study, we present precise (σ = 0.38 km s{sup –1}) radial velocities for proper motion candidate members of NGC 6791 from Platais et al. Our survey, extending down to g' ∼ 16.8, is comprised of the evolved cluster population, including blue stragglers, giants, and horizontal branch stars. Of the 280 proper-motion-selected stars above our magnitude limit, 93% have at least one radial velocity measurement and 79% have three measurements over the course of at least 200 days, sufficient for secure radial-velocity-determined membership of non-velocity-variable stars. The Platais et al. proper motion catalog includes 12 anomalous horizontal branch candidates blueward of the red clump, of which we find only 4 to be cluster members. Three fall slightly blueward of the red clump and the fourth is consistent with being a blue straggler. The cleaned color-magnitude diagram shows a richly populated red giant branch and a blue straggler population. Half of the blue stragglers are in binaries. From our radial velocity measurement distribution, we find the cluster's radial velocity dispersion to be σ {sub c} = 0.62 ± 0.10 km s{sup –1}. This corresponds to a dynamical mass of ∼4600 M {sub ☉}.

79 ASTRONOMY AND ASTROPHYSICS↗

Doppler instrumentation for measuring blood velocity and flow

Doppler ultrasonic blood flowmeters are reviewed in detail. The importance of measurement accuracy for transcutaneous flowmeters and their clinical application is stressed. Doppler imaging was combined with conventional pulse echo imaging, and diagnostic information was extracted from flow signals. The range and extent of applications of Doppler instruments was also presented.

Gill, R. W.↗

Atmospheric Limitations in Stellar Seismology: Should One Measure Radial Velocity or Brightness Fluctuations?

Low degree p-modes of the Sun have been measured in spatially integrated sunlight (the Sun as a star) both in Doppler shift and in intensity fluctuations. These observations are a good starting point for the discussion of the best way to collect equivalent data on other stars. It is assumed that the Sun is removed far enough in space to become an ordinary star of magnitude zero to one. Evidently another star will oscillate with different frequencies and different amplitudes, but some reference must be made to start with. Using this scheme, a detailed investigation of the limitations of observational accuracy in the search for global p-modes is made. The sources of noise stand in the Sun itself, in the instrumentation, in the observing time duration, in the corpuscular nature of the light and mostly in the Earth atmosphere in the case of ground based observations.

Fossat, E.↗

Laser Doppler velocimetry application in the Langley 0.3-meter Transonic Cryogenic Tunnel

The problems and the potential use of a nonintrusive flow velocity measuring technique in the Langley 0.3 meter transonic cryogenic tunnel (TCT) were investigated. A laser velocimeter (LV) was used. It was concluded that free-stream velocity measurements can be successfully made in the Langley 0.3-m TCT using a low-power (15-mW) LV system. The measured and calculated mean velocities typically agreed within one percent. The overall normalized standard deviation was less than one percent. Tunnel vibration and temperature had no detrimental effects on the optical system. It is recommended that the LV work should be further investigated for future use in the Langley 0.3-m TCT.

Gartrell, L. R.↗

Finding a contaminant source in a volume of flowing fluid

A method includes: mapping a boundary of a volume of flowing fluid; partitioning the volume by a computational mesh; finding a contaminant location at a first sensor that is disposed within the volume; obtaining a measured velocity of the flowing fluid within the volume; generating a reversed velocity vector field within the mesh, in response to the measured velocity; time stepping the contaminant location from the first sensor along the reversed velocity vector field until the contaminant location intersects the boundary of the volume; and finding a contaminant source at the intersection of the time stepped contaminant location with the boundary of the volume.

Lopez-Marrero, Vanessa↗

Rayleigh Scattering Diagnostic for Measurement of Velocity and Density Fluctuation Spectra

A new molecular Rayleigh scattering based flow diagnostic is used for the first time to measure the power spectrum of gas density and radial velocity component in the plumes of high speed jets. The technique is based on analyzing the Rayleigh scattered light with a Fabry-Perot interferometer used in the static, imaging mode. The PC based data acquisition system is capable of simultaneous sampling of velocity and density at rates to 100 kHz and data record lengths to 10 million. Velocity and density power spectra and velocity-density cross spectra are presented for a subsonic jet, an underexpanded screeching jet, and for Mach 1.4 and Mach 1.8 supersonic jets. Software and hardware interfaces were developed to allow computer control of all aspects of the experiment and data acquisition.

Seasholtz, Richard G.↗

Considerations for Calibrating a Laser Doppler Anemometer

Laser Doppler Anemometers have long been the device-of-choice for air velocity measurements due to their avoidance of turbulence induced by insertion-method air velocity measurement devices. At first glance, the use of a Laser Doppler Anemometer (LDA) for calibrating air velocity meters appears to be a relatively simple and straightforward process. As is typical in most metrological applications the process becomes much more complex when attempting to use the apparatus to make high-performance, metrology measurements. This paper focuses on the considerations for calibration of a LDA beginning with a discussion why an LDA needs to be calibrated. Other areas of discussion include alignment of the optics, dealing with imperfections in the alignment process, establishing the traceability of measurements from the apparatus and design and development of and experiences with using a calibration apparatus.

"air speed"↗

MASS OF THE SOUTHERN BLACK HOLE IN NGC 6240 FROM LASER GUIDE STAR ADAPTIVE OPTICS

NGC 6240 is a pair of colliding disk galaxies, each with a black hole in its core. We have used laser guide star adaptive optics on the Keck II telescope to obtain high-resolution ({approx}0.''06) near-infrared integral-field spectra of the region surrounding the supermassive black hole in the south nucleus of this galaxy merger. We use the K-band CO absorption bandheads to trace stellar kinematics. We obtain a spatial resolution of about 20 pc and thus directly resolve the sphere of gravitational influence of the massive black hole. We explore two different methods to measure the black hole mass. Using a Jeans Axisymmetric Multi-Gaussian mass model, we investigate the limit that a relaxed mass distribution produces all of the measured velocity dispersion, and find an upper limit on the black hole mass at 2.0 {+-} 0.2 Multiplication-Sign 10{sup 9} M{sub Sun }. When assuming the young stars whose spectra we observe remain in a thin disk, we compare Keplerian velocity fields to the measured two-dimensional velocity field and fit for a mass profile containing a black hole point mass plus a radially varying spherical component, which suggests a lower limit for the black hole mass of 8.7 {+-} 0.3 Multiplication-Sign 10{sup 8} M{sub Sun }. Our measurements of the stellar velocity dispersion place this active galactic nucleus within the scatter of the M{sub BH}-{sigma}{sub *} relation. As NGC 6240 is a merging system, this may indicate that the relation is preserved during a merger at least until the final coalescence of the two nuclei.

79 ASTRONOMY AND ASTROPHYSICS↗

Wind tunnel seeding particles for laser velocimeter

The design of an optimal air foil has been a major challenge for aerospace industries. The main objective is to reduce the drag force while increasing the lift force in various environmental air conditions. Experimental verification of theoretical and computational results is a crucial part of the analysis because of errors buried in the solutions, due to the assumptions made in theoretical work. Experimental studies are an integral part of a good design procedure; however, empirical data are not always error free due to environmental obstacles or poor execution, etc. The reduction of errors in empirical data is a major challenge in wind tunnel testing. One of the recent advances of particular interest is the use of a non-intrusive measurement technique known as laser velocimetry (LV) which allows for obtaining quantitative flow data without introducing flow disturbing probes. The laser velocimeter technique is based on measurement of scattered light by the particles present in the flow but not the velocity of the flow. Therefore, for an accurate flow velocity measurement with laser velocimeters, two criterion are investigated: (1) how well the particles track the local flow field, and (2) the requirement of light scattering efficiency to obtain signals with the LV. In order to demonstrate the concept of predicting the flow velocity by velocity measurement of particle seeding, the theoretical velocity of the gas flow is computed and compared with experimentally obtained velocity of particle seeding.

Ghorieshi, Anthony↗

Phase-Resolved Measurements of Ion Velocity in a Radio-Frequency Sheath

The time-dependent argon-ion velocity distribution function above and within the plasma sheath of an rf-biased substrate has been measured using laser-induced fluorescence in a commercial plasma processing tool. Discharge parameters were such that the 2.2 MHz rf-bias period was on the order of the ion transit time through the sheath ({tau}{sub ion}/{tau}{sub rf}=0.3). This work embodies the first time-resolved measurement of ion velocity distribution functions within an rf-biased sheath over a large area (30 cm diameter) silicon wafer substrate.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Physical and mathematical modelling of ladle metallurgy operations

Experimental measurements are reported, on the velocity fields and turbulence parameters on a water model of an argon stirred ladle. These velocity measurements are complemented by direct heat transfer measurements, obtained by studying the rate at which ice rods immersed into the system melt, at various locations. The theoretical work undertaken involved the use of the turbulence Navier-Stokes equations in conjunction with the kappa-epsilon model to predict the local velocity fields and the maps of the turbulence parameters. Theoretical predictions were in reasonably good agreement with the experimentally measured velocity fields; the agreement between the predicted and the measured turbulence parameters was less perfect, but still satisfactory. The implications of these findings to the modelling of ladle metallurgical operations are discussed.

El-Kaddah, N.↗

Applications of Digital Image Processing 11

A new technique, digital image velocimetry, is proposed for the measurement of instantaneous velocity fields of time dependent flows. A time sequence of single-exposure images of seed particles are captured with a high-speed camera, and a finite number of the single-exposure images are sampled within a prescribed period in time. The sampled images are then digitized on an image processor, enhanced, and superimposed to construct an image which is equivalent to a multiple exposure image used in both laser speckle velocimetry and particle image velocimetry. The superimposed image and a single-exposure Image are digitally Fourier transformed for extraction of information on the velocity field. A great enhancement of the dynamic range of the velocity measurement is accomplished through the new technique by manipulating the Fourier transform of both the single-exposure image and the superimposed image. Also the direction of the velocity vector is unequivocally determined. With the use of a high-speed video camera, the whole process from image acquisition to velocity determination can be carried out electronically; thus this technique can be developed into a real-time capability.

Cho, Y. -C.↗

ORBITS, DISTANCE, AND STELLAR MASSES OF THE MASSIVE TRIPLE STAR σ ORIONIS

We present interferometric observations of the σ Orionis triple system using the CHARA Array, NPOI, and VLTI. Using these measurements, we spatially resolve the orbit of the close spectroscopic binary (Aa,Ab) for the first time and present a revised orbit for the wide pair (A,B). Combining the visual orbits with previously published radial velocity measurements and new radial velocities measured at CTIO, we derive dynamical masses for the three massive stars in the system of M{sub Aa} = 16.99 ± 0.20 M{sub ⊙}, M{sub Ab} = 12.81 ± 0.18 M{sub ⊙}, and M{sub B} = 11.5 ± 1.2 M{sub ⊙}. The inner and outer orbits in the triple are not coplanar, with a relative inclination of 120°–127°. The orbital parallax provides a precise distance of 387.5 ± 1.3 pc to the system. This is a significant improvement over previous estimates of the distance to the young σ Orionis cluster.

79 ASTRONOMY AND ASTROPHYSICS↗

Note: Accuracy of velocity correction for impact of a laser-accelerated miniature flyer with lithium fluoride shock-compressed along the [100] axis

We performed miniature flyer impact experiments to investigate the relationship between the apparent (u{sub a}) and actual (u{sub A}) particle velocities measured by a velocity interferometer in single-crystal lithium fluoride (LiF) that was shock-compressed along the [100] axis. The miniature flyer was accelerated to velocities in the range 652.5-1937.6 m/s by a tabletop pulsed laser. An empirical relationship of u{sub a}= (1.2749 {+-} 0.0102)u{sub A} was obtained. The obtained relationship agreed well with the results of a previous study within the experimental errors and its uncertainty was less than {+-}1%. This result indicates that the present experimental technique is effective for measuring the relationship between u{sub a} and u{sub A} of shocked transparent materials with a comparable accuracy to conventional methods.

36 MATERIALS SCIENCE↗

Angular width of the Cherenkov radiation with inclusion of multiple scattering

Visible Cherenkov radiation can offer a method of the measurement of the velocity of charged particles. The angular width of the radiation is important since it determines the resolution of the velocity measurement. In this article, the angular width of Cherenkov radiation with inclusion of multiple scattering is calculated through the path-integral method, and the analytical expressions are presented. The condition that multiple scattering processes dominate the angular distribution is obtained.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗