Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TWIST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Weavability of dry polymer powder towpreg

Carbon fiber yarns (3k, 6k, 12k) were impregnated with LARC (tm) thermoplastic polyimide dry powder. Parameters for weaving these yarns were established. Eight-harness satin fabrics were successfully woven from each of the three classes of yarns and consolidated into test specimens to determine mechanical properties. It was observed that for optimum results warp yarns should have flexural rigidities between 10,000 and 100,000 mg-cm. Tow handling minimization, low tensioning, and tow bundle twisting were used to reduce fiber breakage, the separation of filaments, and tow-to-tow abrasion. No apparent effect of tow size or twist was observed on either tension or compression modulus. However, fiber damage and processing costs favor the use of 12k yarn bundles versus 3k or 6k yarn bundles in the weaving of powder-coated towpreg.

Hugh, Maylene K.↗
NASA NTRS1995

An active magnetic bearing with high T(sub c) superconducting coils and ferromagnetic cores

A proof-of-feasibility demonstration showed that high-T(sub c) superconductor (HTS) coils can be used in a high-load, active magnetic bearing in LN2. A homopolar radial bearing with commercially wound HTS (Bi 2223) bias and control coils produced over 890 N (200 lb) radial load capacity (measured non-rotatings) and supported a shaft to 14,000 rpm. The goal was to show that HTS coils can operate stably with ferromagnetic cores in a feedback controlled system at a current density similar to that for Cu in LN2. The bias coil, wound with non-twisted, multifilament HTS conductor, dissipated negligible power for its direct current. The control coils, wound with monofilament HTS sheathed in Ag, dissipated negligible power for direct current. AC losses increased rapidly with frequency and quadratically with AC amplitude. Above about 2 Hz, the effective resistance of the control coils exceeds that of the silver which is in electrical parallel with the oxide superconductor. These results show that twisted multifilament conductor is not needed for stable levitation but may be desired to reduce control power for sizable dynamic loads.

Brown, G. V.↗
NASA NTRS1995

Magnetohydrodynamic simulations of outflows from accretion disks

Magnetohydrodynamic simulations have been made of the formation of outflows from a Keplerian disk threaded by a magnetic field. The disk is treated as a boundary condition, where matter is ejected with Keplerian azimuthal speed and poloidal speed less than the slow magnetosonic velocity, and where boundary conditions on the magnetic field correspond to a highly conducting disk. Initially, the space above the disk, the corona, is filled with high specific entropy plasma in thermal equilibrium in the gravitational potential of the central object. The initial magnetic field is poloidal and is represented by a superposition of monopoles located below the plane of the disk. The rotation of the disk twists the initial poloidal magnetic field, and this twist propagates into the corona pushing and collimating matter into jetlike outflow in a cylindrical region. Matter outflowing from the disk flows and accelerates in the z-direction owing to both the magnetic and pressure gradient forces. The flow accelerates through the slow magnetosonic and Alfven surfaces and at larger distances through the fast magnetosonic surface. The flow velocity of the jet is approximately parallel to the z-axis, and the collimation results from the pinching force of the toroidal magnetic field. For a nonrotating disk no collimation is observed.

Ustyugova, G. V.↗
NASA NTRS1995

Coronal loop formation resulting from photospheric convection

We have demonstrated the dynamic formation of coronal magnetic loops in three dimensions as a result of horizontal vortex-like convection on the photosphere. Localized plasma motions twist bipolar magnetic field lines which are tied to the dense photosphere by high electrical conductivity. The twists propagate into the corona along the field and create a narrow quasi-toroidal region where the field lines interwind. At the same time, this tubeline region rises in altitude, expands in cross section, and distorts into a slight S shape before settling into an equilibrium state. The MHD stability of such line-tied magnetic loop structures is directly exhibited by this dynamic simulation.

Hoven, G. Van↗
NASA NTRS1995

An MHD simulation study of the poloidal mode field line resonance in the Earth's dipole magnetosphere

The poloidal mode field line resonance in the Earth's dipole magnetic field is investigated using cold plasma ideal MHD simulations in dipole geometry. In order to excite the poloidal mode resonance, we use either an initial or a continuous velocity perturbation to drive the system. The perturbation is localized at magnetic shell L = 7 with plasma flow in the radial direction (electric field component in the azimuthal direction). It is found that with the initial perturbation alone, no polodial mode resonance can be obtained and the initially localized perturbation spreads out across all magnetic L shells. With the continuous perturbation, oscillating near the poloidal resonance frequency, a global-scale poloidal cavity mode can be obtained. For the first time, a localized guided poloidal mode resonance is obtained when a radial component of electric field is added to the initial perturbation such that the curl of the electric field is everywhere perpendicular to the background dipole magnetic field. During the localized poloidal resonance, plasma vortices parallel/antiparallel to the background dipole magnetic field B(sub 0). This circular flow, elongated radially, results in twisting of magnetic field flux tubes, which, in turn, leads to the slowdown of the circular plasma flow and reversal of the plasma vortices. The energy associated with the localized poloidal resonance is conserved as it shifts back and forth between the oscillating plasma vortices and the alternately twisted magnetic flux tubes. In the simulations the eigenfunctions associated with the localized poloidal resonance are grid-scale singular functions. This result indicates that ideal MHD is inadequate to describe the underlying problem and nonideal MHD effects are needed for mode broadening.

Ding, D. Q.↗
NASA NTRS1996

Development and testing of airfoils for high-altitude aircraft

Specific tasks included airfoil design; study of airfoil constraints on pullout maneuver; selection of tail airfoils; examination of wing twist; test section instrumentation and layout; and integrated airfoil/heat-exchanger tests. In the course of designing the airfoil, specifically for the APEX test vehicle, extensive studies were made over the Mach and Reynolds number ranges of interest. It is intended to be representative of airfoils required for lightweight aircraft operating at extreme altitudes, which is the primary research objective of the APEX program. Also considered were thickness, pitching moment, and off-design behavior. The maximum ceiling parameter M(exp 2)C(sub L) value achievable by the Apex-16 airfoil was found to be a strong constraint on the pullout maneuver. The NACA 1410 and 2410 airfoils (inverted) were identified as good candidates for the tail, with predictable behavior at low Reynolds numbers and good tolerance to flap deflections. With regards to wing twist, it was decided that a simple flat wing was a reasonable compromise. The test section instrumentation consisted of surface pressure taps, wake rakes, surface-mounted microphones, and skin-friction gauges. Also, a modest wind tunnel test was performed for an integrated airfoil/heat-exchanger configuration, which is currently on Aurora's 'Theseus' aircraft. Although not directly related to the APEX tests, the aerodynamics or heat exchangers has been identified as a crucial aspect of designing high-altitude aircraft and hence is relevant to the ERAST program.

Drela, Mark↗
NASA NTRS1996

Magnetic Fluxtube Tunneling

We present numerical simulations of the collision and subsequent interaction of two initially orthogonal, twisted, force free field magnetic fluxtubes. The simulations were carried out using a new three dimensional explicit parallelized Fourier collocation algorithm for solving the viscoresistive equations of compressible magnetohydrodynamics. It is found that, under a wide range of conditions, the fluxtubes can 'tunnel' through each other. Two key conditions must be satisfied for tunneling to occur: the magnetic field must be highly twisted with a field line pitch much greater than 1, and the magnetic Lundquist number must be somewhat large, greater than or equal to 2880. This tunneling behavior has not been seen previously in studies of either vortex tube or magnetic fluxtube interactions. An examination of magnetic field lines shows that tunneling is due to a double reconnection mechanism. Initially orthogonal field lines reconnect at two specific locations, exchange interacting sections and 'pass' through each other. The implications of these results for solar and space plasmas are discussed.

Dahlburg, Russell B.↗
NASA NTRS1998

Magnetotail Structure and its Internal Particle Dynamics During Northward IMF

This study uses Global magnetohydrodynamic (MHD) simulations driven by solar wind data along with Geotail observations of the magnetotail to investigate the magnetotail's response to changes in the interplanetary magnetic field (IMF); observed events used in the study occurred on March 29, 1993 and February 9, 1995. For events from February 9, 1995, we also use the time-dependent MHD magnetic and electric fields and the large-scale kinetic (LSK) technique to examine changes in the Geotail ion velocity distributions. Our MHD simulation shows that on March 29, 1993, during a long period of steady northward IMF, the tail was strongly squeezed and twisted around the Sun-Earth axis in response to variations in the IMF B(sub y) component. The mixed (magnetotail and magnetosheath) plasma observed by Geotail results from the spacecraft's close proximity to the magnetopause and its frequent crossings of this boundary. In our second example (February 9, 1995) the IMF was also steady and northward, and in addition had a significant B(sub y) component. Again the magnetotail was twisted, but not as strongly as on March 29, 1993. The Geotail spacecraft, located approximately 30 R(sub E) downtail, observed highly structured ion distribution functions. Using the time-dependent LSK technique, we investigate the ion sources and acceleration mechanisms affecting the Geotail distribution functions during this interval. At 1325 UT most ions are found to enter the magnetosphere on the dusk side earthward of Geotail with a secondary source on the dawn side in the low latitude boundary layer (LLBL). A small percentage come from the ionosphere. By 1347 UT the majority of the ions come from the dawn side LLBL. The distribution functions measured during the later time interval are much warmer, mainly because particles reaching the spacecraft from the dawnside are affected by nonadiabatic scattering and acceleration in the neutral sheet.

Ashour-Abdalia, M.↗
NASA NTRS1998

Magnetotail Structure and its Internal Particle Dynamics During Northward IMF

This study uses Global magnetohydrodynamic (MHD) simulations driven by solar wind data along with Geotail observations of the magnetotail to investigate the magnetotail's response to changes in the interplanetary magnetic field (IMF); observed events used in the study occurred on March 29, 1993 and February 9, 1995. For events from February 9, 1995, we also use the time-dependent MHD magnetic and electric fields and the large-scale kinetic (LSK) technique to examine changes in the Geotail ion velocity distributions. Our MHD simulation shows that on March 29, 1993, during a long period of steady northward IMF, the tail was strongly squeezed and twisted around the Sun-Earth axis in response to variations in the IMF B(sub y) component. The mixed (magnetotail and magnetosheath) plasma observed by Geotail results from the spacecraft's close proximity to the magnetopause and its frequent crossings of this boundary. In our second example (February 9, 1995) the IMF was also steady and northward, and in addition had a significant B(sub y) component. Again the magnetotail was twisted, but not as strongly as on March 29, 1993. The Geotail spacecraft, located approximately 30 R(sub E) downtail, observed highly structured ion distribution functions. Using the time-dependent LSK technique, we investigate the ion sources and acceleration mechanisms affecting the Geotail distribution functions during this interval. At 1325 UT most ions are found to enter the magnetosphere on the dusk side earthward of Geotail with a secondary source on the dawn side in the low latitude boundary layer (LLBL). A small percentage come from the ionosphere. By 1347 UT the majority of the ions come from the dawn side LLBL. The distribution functions measured during the later time interval are much warmer, mainly because particles reaching the spacecraft from the dawn side are affected by nonadiabatic scattering and acceleration in the neutral sheet.

Ashour-Abdalla, M.↗
NASA NTRS1998

Elastic Buckling of Laminated Plates Under Varying Axial Stresses

The elastic buckling load of simply supported rectangular composite plates subjected to a second degree parabolic variation of axial stresses in the longitudinal direction is calculated using analytical methods. The variation of axial stresses is equilibrated by nonuniform shear stresses along the plate edges and transverse normal stresses. Numerical results are reported for three different cases: (1) orthotropic plates, (2) symmetrically laminated plates with multiple generally orthotropic layers exhibiting coupling between normal moments and twist, and twisting moment and normal curvatures, and (3) unsymmetrically laminated plates. Rayleigh-Ritz method is used to calculate the buckling load. An approximate solution using "reduced bending stiffness" is adopted for unsymmetrically laminated plates. The influence of the aspect ratio is examined, and the results are compared with plates subjected to uniform axial stresses.

Badir, A.↗
NASA NTRS1999

Ames Optimized TCA Configuration

Configuration design at Ames was carried out with the SYN87-SB (single block) Euler code using a 193 x 49 x 65 C-H grid. The Euler solver is coupled to the constrained (NPSOL) and the unconstrained (QNMDIF) optimization packages. Since the single block grid is able to model only wing-body configurations, the nacelle/diverter effects were included in the optimization process by SYN87's option to superimpose the nacelle/diverter interference pressures on the wing. These interference pressures were calculated using the AIRPLANE code. AIRPLANE is an Euler solver that uses a unstructured tetrahedral mesh and is capable of computations about arbitrary complete configurations. In addition, the buoyancy effects of the nacelle/diverters were also included in the design process by imposing the pressure field obtained during the design process onto the triangulated surfaces of the nacelle/diverter mesh generated by AIRPLANE. The interference pressures and nacelle buoyancy effects are added to the final forces after each flow field calculation. Full details of the (recently enhanced) ghost nacelle capability are given in a related talk. The pseudo nacelle corrections were greatly improved during this design cycle. During the Ref H and Cycle 1 design activities, the nacelles were only translated and pitched. In the cycle 2 design effort the nacelles can translate vertically, and pitch to accommodate the changes in the lower surface geometry. The diverter heights (between their leading and trailing edges) were modified during design as the shape of the lower wing changed, with the drag of the diverter changing accordingly. Both adjoint and finite difference gradients were used during optimization. The adjoint-based gradients were found to give good direction in the design space for configurations near the starting point, but as the design approached a minimum, the finite difference gradients were found to be more accurate. Use of finite difference gradients was limited by the CPU time limit available on the Cray machines. A typical optimization run using finite difference gradients can use only 30 to 40 design variables and one optimization iteration within the 8 hour queue limit for the chosen grid size and convergence level. The efficiency afforded by the adjoint method allowed for 50-120 design variables and 5-10 optimization iterations in the 8 hour queue. Geometric perturbations to the wing and fuselage were made using the Hicks/Henne (HH) shape functions. The HH functions were distributed uniformly along the chords of the wing defining sections and lofted linearly. During single-surface design, constraints on thickness and volume at selected wing stations were imposed. Both fuselage camber and cross-sectional area distributions were permitted to change during design. The major disadvantage to the use of these functions is the inherent surface waviness produced by repeated use of such functions. Many smoothing operations were required following optimization runs to produce a configuration with reasonable smoothness. Wagner functions were also used on the wing sections but were never used on the fuselage. The Wagner functions are a family of increasingly oscillatory functions that have also been used extensively in airfoil design. The leading and trailing edge regions of the wing were designed by use of polynomial and monomial functions respectively. Twist was attempted but was abandoned because of little performance improvement available from changing the baseline twist.

Cliff, Susan E.↗
NASA NTRS2000

Three-Dimensional Simulations of the Parker Instability in a Uniformly-Rotating Disk

We investigate the, nonlinear effects of uniform rotation on the Parker instability in an exponentially-stratified disk through high-resolution simulations. During the linear stage, the speed of gas motion is subsonic and the evolution with the rotation is not much different from that without the rotation. This is because the Coriolis force is small. During the nonlinear stage, oppositely-directed supersonic flows near a magnetic valley are under the influence of the Coriolis force with different directions, resulting in twisted magnetic field lines near the valley. Sheet-like structures, which are tilted with respect to the initial field direction, are formed with an 1.5 enhancement of column density with respect to its initial value. Even though uniform rotation doesn't give much impact on density enhancement, it generates helically twisted field lines, which may become an additional support mechanism of clouds.

Kim, Jongsoo↗
NASA NTRS2001

Substituent and Solvent Effects on Excited State Charge Transfer Behavior of Highly Fluorescent Dyes Containing Thiophenylimidazole-Based Aldehydes

The excited state charge transfer for a series of highly fluorescent dyes containing thiophenylimidazole moiety was investigated. These systems follow the Twisted Intramolecular Charge Transfer (TICT) model. Dual fluorescence was observed for each substituted dye. X-ray structures analysis reveals a twisted ground state geometry for the donor substituted aryl on the 4 and 5 position at the imidazole ring. The excited state charge transfer was modeled by a linear solvation energy relationship using Taft's pi and Dimroth's E(sub T)(30) as solvent parameters. There is linear relation between the energy of the fluorescence transition and solvent polarity. The degree of stabilization of the excited state charge transfer was found to be consistent with the intramolecular molecular charge transfer. Excited dipole moment was studied by utilizing the solvatochromic shift method.

Santos, Javier↗
NASA NTRS2001

Correlation of the CME Productivity of Solar Active Regions with Measures of their Global Nonpotentiality from Vector Magnetograms: Baseline Results

From conventional magnetograms and chromospheric and coronal images, it is known qualitatively that the fastest coronal mass ejections (CMEs) are magnetic explosions from sunspot active regions in which the magnetic field is globally strongly sheared and twisted from its minimum-energy potential configuration. In this paper, we present measurements from active-region vector magnetograms that begin to quantify the dependence of the CME productivity of an active region on the global nonpotentiality of its magnetic field. From each of 17 magnetograms of 12 bipolar active regions, we obtain a measure of the size of the active region (the magnetic flux content, phi) and three different measures of the global nonpotentiality (L(sub SS), the length of strong-shear, strong-field main neutral line; I(sub N), the net electric current arching from one polarity to the other; and alpha = muI(subN/phi), a flux-normalized measure of the field twist).

Falconer, David A.↗
NASA NTRS2002

Correlation of the Coronal Mass Ejection Productivity of Solar Active Regions with Measures of their Global Nonpotentiality from Vector Magnetograms: Baseline Results

Conventional magnetograms and chromospheric and coronal images show qualitatively that the fastest coronal mass ejections (CMEs) are magnetic explosions from sunspot active regions where the magnetic field is globally strongly sheared and twisted from its minimum-energy potential configuration. We present measurements from active region vector magnetograms that start to quantify the dependence of an active region's CME productivity on the global nonpotentiality of its magnetic field. From each of 17 magnetograms of 12 bipolar active regions, we measured the size of the active region (the magnetic flux content, phi) and three separate measures of the global nonpotentiality (L(sub SS), the length of strong-shear, strong-field main neutral line: I(sub N), the net electric current connecting one polarity to the other; and alpha = (mu)I(sub N)/phi), a flux normalized measure of the field twist). From these measurements and the observed CME productivity of the active regions, we find that: (1) All three measures of global nonpotentiality are statistically correlated with the active region flux content and with each other; (2) All three measures of global nonpotentiality are significantly correlated with CME productivity. The flux content correlates with CME productivity, but at a lower statistically significant confidence level (less than 95%); (3) The net current is less closely correlated with CME productivity than alpha and the correlation of CME productivity with flux content is even weaker. If these differences in correlation strength, and a significant correlation of alpha with flux content, persist to larger active regions, this would imply that the size of active regions does not affect CME productivity except through global nonpotentiality; and (4) For each of the four global magnetic quantities, the correlation with CME productivity is stronger for a two-day time window for the CME production than for windows half as wide or twice as wide. This plausibly is a result of the most counterproductive active regions producing less than one CME per day, and from the active region's evolution often significantly changing the global nonpotentiality over the course of several days. These results establish that measures of active region global nonpotentiality from vector magnetograms (such as L(sub SS), I(sub N), and alpha) should be useful for prediction a active region CMEs.

Falconer, D. A.↗
NASA NTRS2002

Effects of Structural Deformation and Tube Chirality on Electronic Conductance of Carbon Nanotubes

A combination of large scale classical force-field (UFF), density functional theory (DFT), and tight-binding Green's function transport calculations is used to study the electronic properties of carbon nanotubes under the twist, bending, and atomic force microscope (AFM)-tip deformation. We found that in agreement with experiment a significant change in electronic conductance can be induced by AFM-tip deformation of metallic zigzag tubes and by twist deformation of armchair tubes. The effect is explained in terms of bandstructure change under deformation.

Svizhenko, Alexei↗
NASA NTRS1990

Catamaran Nets

West Coast Netting, Inc.'s net of Hyperester twine, is made of three strands of fiber twisted together by a company-invented sophisticated twisting machine and process that maintain precisely the same tension on each strand. The resulting twine offers higher strength and improved abrasion resistance. The technology that created the Hyperester supertwine has found spinoff applications, first as an extra-efficient seine for tuna fishing, then as a capture net for law enforcement agencies. The newest one is as a deck for racing catamarans. Hyperester twine net has been used on most of the high performance racing catamarans of recent years, including the America's Cup Challenge boats. They are tough and hold up well in the continual exposure to sunlight and saltwater.

Source record↗
NASA NTRS2003

The Formation of Relativistic Jets from Kerr Black Holes

We have performed the first fully three-dimensional general relativistic magnetohydrodynamics (GRMHD) simulation for Schwarzschild and Kerr black holes with a free falling corona and thin accretion disk. The initial simulation results with a Schwarzschild metric show that a jet is created as in the previous axisymmetric simulations with mirror symmetry at the equator. However, the time to form the jet is slightly longer than in the 2-D axisymmetric simulation. We expect that the dynamics of jet formation are modified due to the additional freedom in the azimuth dimension without axisymmetry with respect to the Z axis and reflection symmetry respect to the equatorial plane. The jet which is initially formed due to the twisted magnetic fields and shocks becomes a wind at the later time. The wind flows out with a much wider angle than the initial jet. The twisted magnetic fields at the earlier time were untwisted and less pinched. The accretion disk became thicker than the initial condition. Further simulations with initial perturbations will provide insights for accretion dynamics with instabilities such as magneto-rotational instability (MRI) and accretion-eject instability (AEI). These instabilities may contribute to variabilities observed in microquasars and AGN jets.

Nishikawa, K.-I.↗