Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TUNNEL EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Ultra-High Bypass Ratio Jet Noise

The jet noise from a 1/15 scale model of a Pratt and Whitney Advanced Ducted Propulsor (ADP) was measured in the United Technology Research Center anechoic research tunnel (ART) under a range of operating conditions. Conditions were chosen to match engine operating conditions. Data were obtained at static conditions and at wind tunnel Mach numbers of 0.2, 0.27, and 0.35 to simulate inflight effects on jet noise. Due to a temperature dependence of the secondary nozzle area, the model nozzle secondary to primary area ratio varied from 7.12 at 100 percent thrust to 7.39 at 30 percent thrust. The bypass ratio varied from 10.2 to 11.8 respectively. Comparison of the data with predictions using the current Society of Automotive Engineers (SAE) Jet Noise Prediction Method showed that the current prediction method overpredicted the ADP jet noise by 6 decibels. The data suggest that a simple method of subtracting 6 decibels from the SAE Coaxial Jet Noise Prediction for the merged and secondary flow source components would result in good agreement between predicted and measured levels. The simulated jet noise flight effects with wind tunnel Mach numbers up to 0.35 produced jet noise inflight noise reductions up to 12 decibels. The reductions in jet noise levels were across the entire jet noise spectra, suggesting that the inflight effects affected all source noise components.

Low, John K. C.↗
NASA NTRS1976

Flight effects on JT8D engine jet noise as measured in the NASA Ames 40-by 80-foot wind tunnel

A JT8D-17 turbofan engine was tested in a 40 x 80 ft wind tunnel to determine flight effects on jet noise. The engine was configured as a baseline with conical nozzle, a quiet nacelle 20-lobe ejector/suppressor, and an internal mixer with conical nozzle. Tunnel-off and tunnel-on noise tests were conducted over a range of nozzle pressure ratios (1.2 to 2.1), primary jet velocities (275 to 550 m/s), and tunnel velocities up to 100 m/s. Aft quadrant noise data were measured by a pair of traversing microphones located on a 3-m sideline relative to the engine centerline. Unique correlations and analysis procedures were developed in order to define far-field flight effects from the relatively near-field noise measurements. The ejector/suppressor experienced a significant loss of suppression relative to static measurements during flight while the internal mixer indicated a slight gain in suppression. It is concluded that the wind tunnel is a viable method for studying flight effects on engine jet noise.

Strout, F. G.↗
NASA NTRS1998

Computational Simulation of Semispan Wings in Wind Tunnels

The computational modelling of experiments, with the end aim of providing sufficiently accurate simulations to assess and improve turbulence models is described. Solid wall tunnels are the only tunnels in which the boundary conditions can, in principle, be known exactly. The modelling of the tunnel walls for transonic flows requires the accurate modelling of the viscous displacement effects on the tunnel walls. This paper describes the modelling of semispan wing experiments in solid wall tunnels, with the tunnel walls modelled as inviscid walls, and with all 4 walls modelled viscously. The effect of the viscous effects is discussed, as well as the feasibility of modelling these effects in an inviscid, apriori manner.

Olsen, Mike↗
NASA NTRS1975

Wind tunnel investigation of helicopter-rotor wake effects on three helicopter fuselage models

The effects of rotor wake on helicopter fuselage aerodynamic characteristics were investigated in the Langley V/STOL tunnel. Force, moment, and pressure data were obtained on three fuselage models at various combinations of windspeed, sideslip angle, and pitch angle. The data show that the influence of rotor wake on the helicopter fuselage yawing moment imposes a significant additional thrust requirement on the tail rotor of a single-rotor helicopter at high sideslip angles.

Wilson, J. C.↗
NASA NTRS1973

Comparison of ground and flight test results using a modified F106B aircraft

A F106 aircraft was modified by installing two additional underwing nacelles housing afterburning J85 engines to study exhaust nozzles in flight at Mach numbers up to 1.3. Installation effects were determined for several nozzles by comparing flight and wind-tunnel data. The effect is to decrease boattail drag and delay its drag rise Mach number to about 0.98. A study of Reynolds number effects, carried out at subsonic speeds with afterburning turbofan engines showed boattail drag to be sensitive to Reynolds number. In flight, drag was highest at the lowest Reynolds number, and decreased as the Re number was increased. Static and flyover noise measurements showed that, except for special cases, noise levels at takeoff (M = 0.4) were higher than predicted from static data.

Wilcox, F. A.↗
NASA NTRS1974

Wind tunnel investigation of helicopter rotor wake effects on three helicopter fuselage models

The effects of rotor downwash on helicopter fuselage aerodynamic characteristics were investigated. A rotor model for generating the downwash was mounted close to each of three fuselage models. The main report presents the force and moment data in both graphical and tabular form and the pressure data in graphical form. This supplement presents the pressure data in tabular form. Each run or parameter sweep is identified by a unique run number. The data points in each run are identified by a point number. The pressure data can be matched to the force data by matching the run and point number.

Wilson, J. C.↗
NASA NTRS1923

Model supports and their effects on the results of wind tunnel tests

The airflow about a model while being tested is often sufficiently affected by the model support to lead to erroneous conclusions unless appropriate corrections are used. In this paper some new material on the subject is presented, together with a review of the airfoil support corrections used in several other laboratories.

Bacon, David L↗
NASA NTRS1961

Investigation of the Static Longitudinal and Lateral Stability Characteristics of a 0.10-Scale Model of a Three-Stage Configuration of the Scout Research Vehicle at Mach Numbers of 2.29, 2.96, 3.96, and 4.65

An investigation w a s made i n the Langley Unitary Plan wind tunnel o determine the effects of fin area and the effects of antennas and w iring tunnels on the static longitudinal and lateral stability of a 0 .10- scale model of a three- stage configuration of the Scout vehicle. The tests were performed at Mach numbers of 2.29, 2.96, 3.96, and 4. 65 6 and at Reynolds numbers of about 3.5 X 10 per foot.

Jernell, Lloyd S.↗
NASA NTRSDate not supplied

Wall-modeled LES of Flow Over a Gaussian Bump

We perform wall-modeled large eddy simulations (WMLES) of turbulent flow over a Gaussian-shaped bump geometry, to assess its performance in the accelerating and separation regions of the flow. The flow conditions are based on the ongoing CFD validation experiments of Slotnick [NATO STO-MP-AVT-307, 2019]. The oncoming flow Mach number is 0.176, and two Reynolds numbers are simulated that are about 10000 and 36000 based on boundary layer thickness upstream of the bump. Preliminary Reynolds-averaged Navier-Stokes simulations are first performed to assess the effects of Mach number, Reynolds number, tunnel top and sidewall effects. Finally, WMLES results with an equilibrium wall model will be presented at two Reynolds numbers to assess their performance for this flow by making detailed comparisons with available experimental and higher-fidelity numerical data.

turbulence, wall model, large eddy simulation↗
NASA NTRS1982

Similarity rules for effects of sidewall boundary layer in two-dimensional wind tunnels

A simple analysis of the interaction of the model pressure field with the boundary layer on an unventilated wind tunnel wall is presented. It is shown that the effects of this interaction are similar to compressibility effects for sidewall boundary layers in two dimensional wind tunnels. This similarity is used to derive modified forms of the Prandtl Glauert rule for subsonic flow and the von Karman rule for transonic flow which are validated by comparison with experimental data. The three dimensional interaction problem is discussed, and it is shown that model pressure field/wall boundary layer interaction effects are not similar to compressibility effects in three dimensional wind tunnels.

Barnwell, R. W.↗
NASA NTRS1986

Wind tunnel technology for the development of future commercial aircraft

Requirements for new technologies in the area of civil aircraft design are mainly related to the high cost involved in the purchase of modern, fuel saving aircraft. A second important factor is the long term rise in the price of fuel. The demonstration of the benefits of new technologies, as far as these are related to aerodynamics, will,for the foreseeable future, still be based on wind tunnel measurements. Theoretical computation methods are very successfully used in design work, wing optimization, and an estimation of the Reynolds number effect. However, wind tunnel tests are still needed to verify the feasibility of the considered concepts. Along with other costs, the cost for the wind tunnel tests needed for the development of an aircraft is steadily increasing. The present investigation is concerned with the effect of numerical aerodynamics and civil aircraft technology on the development of wind tunnels. Attention is given to the requirements for the wind tunnel, investigative methods, measurement technology, models, and the relation between wind tunnel experiments and theoretical methods.

Szodruch, J.↗