SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Fiber optic sensing for strain and temperature. This presentation reports the status of the R&D work performed at FNAL on a novel diagnostic tool for superconducting magnet based on fiber optics.
Recently a new type of device, capacitor-based, aiming to eliminate or reduce superconducting magnet training was developed and tested at FNAL. I’ll review its main characteristics and principles of operation, make relevant comparisons and conclusions. Separately, I’ll discuss somewhat similar concepts based on induced vibrations in magnets, but I’ll extend this topic to cover both training reduction and quench protection. Those will be discussed at conceptual level, arguing about feasibility of such an approach and the need for more focused research on the topic, including simulations.
As superconducting magnet technology is pushed towards higher performance, energy density and total stored energy follow exponentially. Protecting magnets becomes substantially more challenging with traditional methods being stretched to their limits. New technologies such as CLIQ promise to provide a robust method to protect advanced magnets, however they become inductance limited in large magnet strings or at low field, leading to more complex configurations. A technique to substantially reduce this limitation and improve response time is presented, by winding a coil in a bifilar fashion. This allows for extremely high di/dt. The concept is then demonstrated on a small REBCO coil.
The experimental isolation of graphene led to the discovery of an entirely new world of two-dimensional (2D) materials in which the 2D nature often leads to emergent behaviors not seen in bulk systems. 2D transition metal dichalcogenides (TMDs) exhibit physico-chemical properties that depend on the transition metal, polymorph, thickness, and presence and type of defects. Recently, a group of thin (10-100nm) transition metal carbides (TMCs), such as Mo2C, has been synthesized that exhibit a thickness-dependent superconducting critical temperature (Tc). These thin TMCs are different from MXenes, another class of 2D materials consisting of few layers of nitrides or carbides (<5nm) produced by chemical etching and delamination. The goal of this renewal proposal is to combine experiment and computation to synthesize and elucidate the guiding principles that control the growth, orientation and strain of heterostacks of thin TMCs and TMDs composed with Nb, Ti and W. We expect to stabilize metastable hybrid phases of TMCs sandwiched between TMDs (H-TMD/Cs) with unprecedented physico-chemical properties. As part of previous DOE-funded work by the Terrones/Sinnott groups, thin (10-100 nm thick) Mo2C flakes were successfully synthesized by chemical vapor deposition (CVD). By subsequently exposing Mo2C to H2S, partial chalcogenization was achieved, resulting in heterostacks of MoCx phases and MoS2. The formation of MoS2 led to a deficiency of Mo atoms in the underlying Mo2C, resulting in an inhomogeneous phase change from α-Mo2C to γ’-MoCx and then to γ-MoC. The γ’-MoCx is a strained metastable phase and the heterostack of all three phases demonstrated an increased Tc relative to that of α-Mo2C, from 4 to 6K; its interleaved layered structure consisting of superconducting and semiconducting phases is ideal for future studies of Josephson junction series arrays. Moiré patterns in these heterostacked systems could result in new phenomena, as moiré patterns in bilayer graphene showed unconventional superconductivity and moiré excitons have been observed in twisted TMD heterobilayers. The scientific hypothesis of the proposed synergistic computational and experimental research is that orientation and strain control within confined thin metastable TMCs, sandwiched by stable phases of TMCs and layered TMDs, will depend on kinetic and thermodynamic “knobs” that include fast temperature changes, chalcogen diffusion through preferred crystallographic planes, reaction times, pressure, reactive atmosphere, precursors, and surfactants, which will also tailor properties such as superconductivity, magnetism, ferroelectricity, piezoelectricity, and catalytic performance. We will develop the guiding principles for the synthesis and stabilization of metastable H-TMD/Cs based on Nb, Ti and W. In order to validate the hypothesis, four tasks are proposed: The first task will synthesize ultra-thin TMCs based on Nb, W and Ti, by: 1) adapting the CVD method used for Mo2C, 2) plasma assisted CVD, 3) defect-mediated CVD processes, and 4) cryo-milling of carbide powders. The second task will accomplish the synthesis and basic physico-chemical characterizations of H-TMD/Cs by chalcogenization of the materials synthesized in task one, and by carbonization of TMDs. H-TMD/Cs will also be investigated for their suitability in energy conversion applications such as supercapacitors, Li and multivalent ion batteries, and electrocatalysts, topics of interest to DoE. These tasks will be carried out in close conjunction with density functional theory (DFT) calculations with insights into energetics, lattice parameters, stability, phase diagrams, band structures, and density of states of H-TMD/Cs. The third task will characterize and evaluate strain and moiré patterns at the interfaces of different H-TMD/Cs by high-resolution scanning transmission electron microscopy (HR-STEM), scanning tunneling microscopy (STM), and conductive tip atomic force microscopy. Nudged elastic band calculations with DFT will be performed to understand the chalcogen diffusion process, which will provide insights into the interfaces between different phases of TMCs and TMDs. The fourth task aims at quantifying the stability and dynamics of H-TMD/Cs by in-situ TEM and Raman studies under heating, strain, and electrical biasing. Phonon calculations using DFT will provide a basis for interpreting Raman spectra. This coherent framework involving synthesis, characterization, and computation will result in a broad scientific impact for energy related applications. The ability to develop new H-TMD/Cs will enhance a range of applications that include batteries, catalysts, switches, sensors, quantum computing components and smart coatings.
The experimental isolation of graphene led to the discovery of an entirely new world of two-dimensional (2D) materials in which the 2D nature often leads to emergent behaviors not seen in bulk systems. 2D transition metal dichalcogenides (TMDs) exhibit physico-chemical properties that depend on the transition metal, polymorph, thickness, and presence and type of defects. Recently, a group of thin (10-100nm) transition metal carbides (TMCs), such as Mo 2 C, has been synthesized that exhibit a thickness-dependent superconducting critical temperature (Tc). These thin TMCs are different from MXenes, another class of 2D materials consisting of few layers of nitrides or carbides (<5nm) produced by chemical etching and delamination. The goal of this renewal proposal is to combine experiment and computation to synthesize and elucidate the guiding principles that control the growth, orientation and strain of heterostacks of thin TMCs and TMDs composed with Nb, Ti and W. We expect to stabilize metastable hybrid phases of TMCs sandwiched between TMDs (H-TMD/Cs) with unprecedented physico-chemical properties. As part of previous DOE-funded work by the Terrones/Sinnott groups, thin (10-100 nm thick) Mo 2 C flakes were successfully synthesized by chemical vapor deposition (CVD). By subsequently exposing Mo 2 C to H 2 S, partial chalcogenization was achieved, resulting in heterostacks of MoCx phases and MoS 2 . The formation of MoS 2 led to a deficiency of Mo atoms in the underlying Mo 2 C, resulting in an inhomogeneous phase change from α-Mo 2 C to γ’-MoCx and then to γ-MoC. The γ’-MoCx is a strained metastable phase and the heterostack of all three phases demonstrated an increased Tc relative to that of α-Mo 2 C, from 4 to 6K; its interleaved layered structure consisting of superconducting and semiconducting phases is ideal for future studies of Josephson junction series arrays. Moiré patterns in these heterostacked systems could result in new phenomena, as moiré patterns in bilayer graphene showed unconventional superconductivity and moiré excitons have been observed in twisted TMD heterobilayers. The scientific hypothesis of the proposed synergistic computational and experimental research is that orientation and strain control within confined thin metastable TMCs, sandwiched by stable phases of TMCs and layered TMDs, will depend on kinetic and thermodynamic “knobs” that include fast temperature changes, chalcogen diffusion through preferred crystallographic planes, reaction times, pressure, reactive atmosphere, precursors, and surfactants, which will also tailor properties such as superconductivity, magnetism, ferroelectricity, piezoelectricity, and catalytic performance. We will develop the guiding principles for the synthesis and stabilization of metastable H-TMD/Cs based on Nb, Ti and W. In order to validate the hypothesis, four tasks are proposed: The first task will synthesize ultra-thin TMCs based on Nb, W and Ti, by: 1) adapting the CVD method used for Mo 2 C, 2) plasma assisted CVD, 3) defect-mediated CVD processes, and 4) cryo-milling of carbide powders. The second task will accomplish the synthesis and basic physico-chemical characterizations of H-TMD/Cs by chalcogenization of the materials synthesized in task one, and by carbonization of TMDs. H-TMD/Cs will also be investigated for their suitability in energy conversion applications such as supercapacitors, Li and multivalent ion batteries, and electrocatalysts, topics of interest to DoE. These tasks will be carried out in close conjunction with density functional theory (DFT) calculations with insights into energetics, lattice parameters, stability, phase diagrams, band structures, and density of states of H-TMD/Cs. The third task will characterize and evaluate strain and moiré patterns at the interfaces of different H-TMD/Cs by high-resolution scanning transmission electron microscopy (HR-STEM), scanning tunneling microscopy (STM), and conductive tip atomic force microscopy. Nudged elastic band calculations with DFT will be performed to understand the chalcogen diffusion process, which will provide insights into the interfaces between different phases of TMCs and TMDs. The fourth task aims at quantifying the stability and dynamics of H-TMD/Cs by in-situ TEM and Raman studies under heating, strain, and electrical biasing. Phonon calculations using DFT will provide a basis for interpreting Raman spectra. This coherent framework involving synthesis, characterization, and computation will result in a broad scientific impact for energy related applications. The ability to develop new H-TMD/Cs will enhance a range of applications that include batteries, catalysts, switches, sensors, quantum computing components and smart coatings.
Just after 12:30 PM on August 1, 2023, the RHIC superconducting magnet quench system triggered and consequently the energy dump resistors were switched into the blue ring quad and dipole circuits and the interaction region DX dipole heaters were switched on. This was a spurious trip (there was no actual quench) and was not unusual as the outdoor summer temperature often caused the quench detectors to cause such trips. The collider control room notified the on-duty cryogenics technical staff of the quench trip. A short time later building 1004B cryogenic low-helium and valve box insulation vacuum failure alarms were observed. The cryogenics technical staff observed the cryo-relief line from the blue ring valve box was exhausting helium outside the building.
The Electron Ion Collider (EIC) Hadron Storage Ring (HSR) will reuse most of the existing superconducting magnets from the RHIC storage ring. However, the existing beam vacuum chamber and stripline BPMs will not be compatible with the planned EIC hadron bunches that will have a 3x higher intensity and be 10x shorter, and some operational scenarios with large radial offsets of the beam in the vacuum chamber. To address these challenges, a copper coated beam screen will be implemented, the existing RHIC stripline BPMs will be shielded and an interconnect module design, including new BPM will be installed adjacent to the existing BPMs. A thermal analysis of the new arc BPM interconnect housing has been conducted to assess the heating caused by beam induced resistive wall heating and electron cloud heating. An analysis of the BPM module has been made and reported separately. This report will focus on the other side of the interconnect module, containing the RF fingers.
In this talk I will discuss accelerator R&D topics critical for future colliders. These colliders include circular and linear e+e- Higgs factories, and longer-term options such as muon and hadron high energy colliders. Emphasis will be placed on describing R&D for activities prioritized in the recent P5 report. The talk will cover radio frequency technology, high-filed superconducting magnets, muon cooling, energy efficiency, and other R&D topics.
The Workshop for Applied Nuclear Data Activities (WANDA) is designed to increase communication among nuclear data (ND) users in multidisciplinary federal programs, ND producers, ND funders, and other ND experts. It also presents an opportunity to cross-pollinate ideas as well as introduce ND gaps identified by federal programs to ND experts and ND capabilities to the various federal ND users. WANDA 2024 included five technical sessions, three of which focused on Fusion Energy Sciences (FES)—FES Fusion Neutronics, FES Tritium Production, and FES Material Damage—and two stand-alone sessions—Isotopes and Targetry for Nuclear Data and Uncertainty Quantification. The FES sessions successfully brought new voices to the WANDA discussions, expanding the application space in which nuclear data are critical. FES programs need accurate nuclear data with realistic uncertainty quantification to properly estimate, for example, shielding, activation, tritium production, helium production, structural material integrity, and superconducting magnet operation. This includes a variety of projectile (neutrons, photons, charged particles) and target atoms. One of the action items common to all the FES sessions was a need to perform sensitivity studies to identify the prioritization of nuclear data needs. The Isotopes and Targetry session highlighted the many capabilities available to produce high-quality targets for nuclear data measurements, including 3D printing with spherical powders, combustion synthesis coupled with spin coating & electrospraying, inkjet printing, and isotopic doping. These new methods open doors for more accurate measurement, but it was also stressed that sample characterization following any method of fabrication is of the highest importance to accurately interpret nuclear data measurement results that used that sample. The Uncertainty Quantification (UQ) session was broken into two categories: nuclear data uncertainty quantification and the use of that uncertainty quantification. Thematic to the UQ session was the loss of information when going from nuclear data measurement, to evaluation, to evaluated file, and finally to neutron transport calculations. Current evaluated ND libraries typically only contain covariances, which assume that the probability distributions are Gaussian. Beyond being a simplified assumption for many evaluations, this can lead to negative values on many observables when attempting to sample the covariance. The covariance format, however, is very efficient in that a simple set of linear equations can transform uncertainty from parameters or cross sections to the application of interest. Focused collaboration is needed between nuclear data evaluators and nuclear data users to ensure that needs are being met.
The hadron storage ring (HSR) of the Electron-Ion Collider (EIC) will use the superconducting magnets from the Relativistic Heavy Ion Collider (RHIC). However, the beam pipes of these magnets show too large resistive-wall impedance and secondary electron yield to the HSR beams. The planned solution is to install beam screens that feature a thin film of amorphous carbon with low SEY on top of a high RRR copper layer for reduced impedance. This note discusses beam-impedance considerations that impact the EIC HSR beam screen design.
The automated coil winder project creates a repeatable, scalable method for producing superconducting magnet coils with increased accuracy and efficiency. The design uses an ortho cyclic winding method to achieve high fill factors by combining computer numerical control (CNC), microcontroller-based controls, and sophisticated optimization techniques. The method optimizes coil turns, core geometry, and current consumption by utilizing analytical models based on magnetic moment, Ohm’s law, and power constraints. For particle accelerator applications, prototype testing using a 3D-printed coil winder has shown enhanced winding repeatability, thermal management, and manufacturability.
The Deep Underground Neutrino Experiment (DUNE) is a next-generation project aiming to study several neutrino properties. It will feature two experimental setups: a near detector that will be installed at Fermilab, in proximity of the neutrino-production point, and a far detector at a distance of 1300 km and 1500 m underground, at the SURF laboratory. The DUNE design and configuration will allow the study of neutrino oscillation, astrophysical neutrinos, and beyond standard model physics. The near detector complex foresees three detectors to be installed. Among these, the System for on-Axis Neutrino Detection (SAND) will serve as on-axis beam monitor, reduce the systematic uncertainties for the oscillation analysis, and search for physics beyond the standard model. SAND will be composed of three sub-detectors, surrounded by a 0.6 T superconducting magnet. The outermost detector will be a lead/scintillating-fiber electromagnetic calorimeter while the inner volume will include a 1-ton liquid argon active target placed upstream followed by a target tracker system. The SAND detector and its goals will be shown in this poster.
The Deep Underground Neutrino Experiment Near Detector complex aims at constraining the systematic uncertainties and deconvolving the neutrino beam flux and cross-section models. The System for on-Axis Neutrino Detection (SAND) is the Near Detector component permanently on-axis. SAND is based on the 0.6 T superconducting magnet and electromagnetic calorimeter previously used in the KLOE experiment. The 40 m3 magnetic volume will be filled with an active target/tracker system. One considered option foresees an upstream liquid Argon active target (about 1.5 t) and a Straw Tube Tracker (about 5 t). In this talk the design of SAND will be described and its performances discussed in view of the SAND primary goals, namely the beam monitoring and neutrino flux measurements.
The Mu2e experiment, currently under construction at Fermilab, will search for neutrinoless mu->e conversion in the field of an aluminum atom. A clear signature of this chargedlepton flavor violating two-body process is given by the monoenergetic conversion electron of 104.97 MeV produced in the final state.An 8 GeV/c pulsed proton beam interacting on a tungsten target will produce the pions decaying in muons; a set of superconducting magnets will drive the negative muon beam to a segmented aluminum target where the stopped muons will eventually convert to electrons; a set of detectors will be used to both identify conversion electrons and reject beam and cosmic backgrounds.The experiment will need 3-5 years of data-taking to achieve a factor of $10^4$ improvement on the current best limit on the conversion rate.After an introduction to the physics of Mu2e, we will report on the status of the different components of the experimental apparatus. The updated estimate of the experiment’s sensitivity and discovery potential will be presented.
Machine learning (ML) has the potential for significant impact on the modeling, operation, and control of particle accelerators due to its ability to model nonlinear behavior, interpolate on complicated surfaces, and adapt to system changes over time. Anomaly detection in particular has been highlighted as an area where ML can significantly impact the operation of accelerators. These algorithms work by identifying subtle behaviors of key variables prior to negative events. Efforts to apply ML to anomaly detection have largely focused on subsystems such as RF cavities, superconducting magnets, and losses in rings. However, dedicated efforts to understand how to apply ML for anomaly detection in linear accelerators have been limited. In this paper the use of autoencoders is explored to identify anomalous behavior in measured data from the Fermilab low-energy linear accelerator.
Investigation focused on the behavior of superconducting magnet and its constituent materials during and after exposure to nuclear radiation. The results will indicate the feasibility of their use in diverse applications and various environments.
Internal Compton effect, and use of superconducting magnet spectrometer to determine multipolarity assignments
Research on lithium drifted silicon detectors, Compton effect using superconducting magnet beta ray spectrometer, and high Z semiconductors for radiation detectors