SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Progress is reviewed in the development, delivery, and support of two prototype solar heating and cooling systems including potable hot water. The system consisted of the following subsystems: collector, auxiliary heating, potable hot water, storage, control, transport, and government-furnished site data acquisition.
Tests, test results, examination and evaluation by Underwriters Laboratory, Inc., of a single family solar heating and hot water system consisting of collector, storage, control, transport, and data acquisition are presented. The structural characteristics of the solar flat plate collectors were evaluated according to snow and wind loads indicated in various building codes to determine their suitability for use both Michigan and Pennsylvania where prototype systems were installed. The flame spread classification of the thermal insulation is discussed and the fire tests conducted on components are described. The operation and dielectrics withstand tests of the energy transport module indicate the module is capable of rated air delivery. Tests of the control panel indicate the relay coil temperatures exceed the temperature limits allowed for the insulating materials involved.
A commercial Czochralski crystal growing furnace was converted to a continuous growth facility by installation of a small, in-situ premelter with attendant silicon storage and transport mechanisms. Using a vertical, cylindrical graphite heater containing a small fused quartz test tube linear from which the molten silicon flowed out the bottom, approximately 83 cm of nominal 5 cm diamter crystal was grown with continuous melt addition furnished by the test tube premelter. High perfection crystal was not obtained, however, due primarily to particulate contamination of the melt. A major contributor to the particulate problem was severe silicon oxide buildup on the premelter which would ultimately drop into the primary melt. Elimination of this oxide buildup will require extensive study and experimentation and the ultimate success of continuous Czochralski depends on a successful solution to this problem. Economically, the continuous Czochralski meets near-term cost goals for silicon sheet material.
Economic feasibility of methanol or methyl fuel produced from coal using existing technology is discussed. Other factors considered include environmental, safety, toxicity, transportation, so storage, ease of burning, and retrofitting of present boilers. Demonstrations of its uses as a boiler fuel and as a turbine fuel are cited.
The advanced thermal power technology program which develops and applies advanced technology for improved solar thermal energy subsystems and components. It is shown that the effort is aimed at systems which can achieve significant energy cost reductions. The paper describes the potential for advanced technology to achieve commercially attractive solar thermal systems and describes some recent developments in advanced heat engines, high temperature receivers, chemical transport, and storage.
The initial design of a solar domestic hot water system is considered. The system performance specification and detailed design drawings are included. The hot water systems consist of the following subsystems: collector, storage, control, transport, auxiliary energy, and government-furnished site data acquisition. The two systems are installed at Tempe, Arizona, and San Diego, California.
Lightweight half-lengths of columns for truss structures are described. The columns are adapted for nestable storage and transport to facilitate fabrication of large area truss structures at a remote site and particularly adaptable for space applications.
The successful application of aerospace technology to problems related to highways and rail and rapid transit systems is described with emphasis on the use of corrosion resistant paints, fire retardant materials, and law enforcement. Possible areas for the use of spinoff from NASA technology by the California State Department of Corrections are identified. These include drug detection, security and warning systems, and the transportation and storage of food. A communication system for emergency services is also described.
A global terrestrial hydrology model has been developed for the transport and storage of moisture and heat in the ground surface layer where the hydrological parameters react to diurnal and seasonal changes in the atmosphere. The spatial and temporal variability of land surface features is considered in the model by means of large scale parameterizations. The model can be either forced by the atmosphere using conventional meteorological data or coupled to an atmospheric general circulation model (GCM) for interactive studies. The global surface is divided into 4 deg longitude by 5 deg latitude cells while the ground is represented by a thin surface layer, a bulk layer (the root zone), and a deep layer (the ground water zone). Results are presented from a seven-day global experiment which was conducted utilizing the GLAS GCM (NASA Goddard Laboratory for Atmospheric Sciences). The model has demonstrated its capability to predict, over a large region, the overall soil moisture storage and major flux exchanges with the atmosphere above and the ground water below.
The hydrogen containment materials are studied. The safe, reliable, and economic containment of hydrogen is essential to the success of virtually any hydrogen energy transport and storage scheme. The potential problems associated with hydrogen containment are presented.
The high temperature catalytic dissocation of SO3 is an important chemical process being considered in the development and application of solar-thermal energy conversion, transport, and storage systems. A facility for evaluating chemical converter-heat exchangers at temperatures to 1000 C with high flow rates of gaseous SO3 feedstock has been assembled and operated on the NMSU campus. Several quartz and metal reactors containing different catalyst configurations have been tested. Descriptions of the test facility and of the reactors are given along with a presentation and discussion of experimental results.
One of the research and development efforts in the Solar Thermal Energy Systems Project at the Jet Propulsion Laboratory has been focused on application of ceramic components for advanced point-focus solar receivers. The impetus for this effort is a need for high efficiency, low cost solar receivers which operate in a temperature regime where use of metal components is impractical. The current status of the work on evaluation of ceramic components at JPL and elsewhere is outlined and areas where lack of knowledge is currently slowing application of ceramics are discussed. Future developments of ceramic processing technology and reliability assurance methodology should open up applications for the point-focus solar concentrator system in fuels and chemicals production, in thermochemical energy transport and storage, in detoxification of hazardous materials and in high temperature process heat as well as for electric power generation.
Cable-controlled mechanisms allow large structures stored in small spaces. Combination of telescoping struts and pivot points allows very large structure collapsed into very small one. Concept used not only for straight but for tapered or curved ones as well. Structure adaptable to terrestrial uses as portable towers, scaffolds, and bridge beams folded compactly for transportation or storage.
Satellites now play an increasing role in systematic monitoring of the global oceans. Measurements of sea surface temperature (SST) are of primary importance in understanding heat storage and transport within the ocean and cross the ocean-atmosphere boundary. In some regions, local changes in SST of only 1 to 2 C have major effects on global climate and weather patterns. The satellite measurements provide a data base complementary to the (sometimes) accurate but sparsely-distributed point measurements available from ships and buoys. The demands placed on satellite sensors are stringent. Accuracies of better than 1 C are required and are often desired to a few tenths of a degree. Furthermore, measurement accuracies must be stable spatially and temporally in order for satellite data to be used with confidence in models of air-sea interaction and climate. There now exists a need to evaluate objectively the performance of the latest generation of sensors under a sufficient variety of environmental conditions to indicate present accuracies, deficiencies, and potential for improvement.
Thermodynamics, mechanical stability, and mass penalties affect design. Pair of reports presents design study for propellant tanks used in low gravity. Each tank, which most likely contains liquid H2 or O2, part of fuel depot tethered to station in orbit around Earth. Some engineering concepts in study applied to design of tanks for use on Earth in transport and storage of cryogenic liquids and other fluids requiring special handling.
Report describes research on engineering issues related to storage and transport of heat in slurries containing phase-change materials in microscopic capsules. Specific goal of project to develop lightweight, compact, heat-management systems used safely in inhabited areas of spacecraft. Further development of obvious potential of technology expected to lead to commercialization and use in aircraft, electronic equipment, machinery, industrial processes, and other sytems in which requirements for management of heat compete with severe restrictions on weight or volume.
The objectives were to identify the space station waste gases and their characteristics, and to investigate compressor and dryer types, as well as transport and storage requirements with tradeoffs leading to a preliminary system definition.
Safety testing is intended to simulate, under laboratory conditions and controls, situations that will subject a cell to externally induced stress. The stresses can occur at any time during the useful life of the cell, from the time of manufacture until it is expended during mission deployment. Abuse testing can be divided into three major categories: Electrical, Mechanical, and Thermal. Although electrical abuses are generally found to occur during handling or deployment, Mechanical and Thermal stresses can be induced during transportation and storage. Therefore, it would be prudent to include predicted environmental exposure as part of the test plan. In the selection of a test program. specific test requirements should be tailored to meet the predicted mission requirements.