Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stainless Steel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Electrochemical Evaluation of Stainless Steels in Acidified Sodium Chloride Solutions

This paper presents the results of an investigation in which several 300-series stainless steels (SS): AISI S30403 SS (UNS S30403), AISI 316L SS (UNS S31603), and AISI 317L SS (LINS S31703), as well as highly-alloyed: SS 254-SMO (UNS S32154), AL-6XN (N08367) and AL29-4C (UNS S44735), were evaluated using DC electrochemical techniques in three different electrolyte solutions. The solutions consisted of neutral 3.55% NaCl, 3.55% NaCl in 0.1N HCl, and 3.55% NaCl in 1.0N HCl. These solutions were chosen to simulate environments that are less, similar, and more aggressive, respectively, than the conditions at the Space Shuttle launch pads. The electrochemical test results were compared to atmospheric exposure data and evaluated for their ability to predict the long-term corrosion performance of the subject alloys. The electrochemical measurements for the six alloys indicated that the higher-alloyed SS 254-SMO, AL29-4C, and AL-6XN exhibited significantly higher resistance to localized corrosion than the 300-series SS. There was a correlation between the corrosion performance of the alloys during a two-year atmospheric exposure and the corrosion rates calculated from electrochemical (polarization resistance) measurements.

Calle, L. M.↗
DOE OSTI2022

Process and feedstock driven microstructure for laser powder bed fusion of 316L stainless steel

Here in the pursuit of improving additively manufactured (AM) component quality and reliability, fine-tuning critical process parameters such as laser power and scan speed is a great first step toward limiting defect formation and optimizing the microstructure. However, the synergistic effects between these process parameters, layer thickness, and feedstock attributes (e.g. powder size distribution) on part characteristics such as microstructure, density, hardness, and surface roughness are not as well-studied. In this work, we investigate 316L stainless steel density cubes built via laser powder bed fusion (L-PBF), emphasizing the significant microstructural changes that occur due to altering the volumetric energy density (VED) via laser power, scan speed, and layer thickness changes, coupled with different starting powder size distributions. This study demonstrates that there is not one ideal process set and powder size distribution for each machine. Instead, there are several combinations or feedstock/process parameter ‘recipes’ to achieve similar goals. This study also establishes that for equivalent VEDs, changing powder size can significantly alter part density, GND density, and hardness. Through proper parameter and feedstock control, part attributes such as density, grain size, texture, dislocation density, hardness, and surface roughness can be customized, thereby creating multiple high-performance regions in the AM process space.

316L stainless steel↗
DOE OSTI2020

In-situ synthesis of oxides by reactive process atmospheres during L-PBF of stainless steel

Traditionally, reactive gases such as oxygen (O 2 ) and carbon dioxide (CO 2 ) have been avoided during laser powder bed fusion (L-PBF) of metals and alloys based on the notion that it may lead to defect formation and poor properties. Here, in this work, we show that instead, these gases can be used to form sub-μm-sized oxide particles in-situ during the L-PBF process in an Fe-Cr-Al-Ti stainless steel and lead to improved room temperature and high-temperature mechanical properties. We manufactured cube samples using pure Ar and various reactive gas atmospheres, namely an O 2 /Argon (Ar) mixture containing 0.2 % O 2 and CO 2 /Ar mixtures containing up to 100 % CO 2 . Co-axial measurements of infrared radiation emitted from the melt pool showed correlation to the presence of O 2 or CO 2 in the gas mixture. Builds produced under CO 2 -containing atmosphere contained complex oxides with an average diameter of ~40 nm, an Al-rich core and a Ti-rich shell. Due to the high cooling rates typical to L-PBF, agglomeration of oxides and slag formation on the surface of the samples could almost be entirely avoided. Compression tests at temperatures up to 800 °C showed that the samples produced in 100 % CO 2 have about 20 % higher yield stress compared to samples produced in Ar. The paper concludes with a discussion of the formation mechanism of the observed oxides. Our results show that in-situ reactions during additive manufacturing processes are a promising pathway to the synthesis of particle-reinforced alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Residual strain and microstructure evolution in 316L stainless steel fabricated by hybrid additive/subtractive manufacturing

The extreme thermal gradients in additive manufacturing (AM) result in residual strains. Subsequent machining operations can relieve the AM strains but can introduce additional strains. AM and machining on the same platform, also called interleaving, during hybrid manufacturing has been shown to improve productivity. However, the impacts of these operations on the resulting residual strains are not well understood. In this investigation, neutron diffraction was used to measure residual strains in hybrid manufactured 316L stainless steel where blown-powder laser directed energy deposition (DED), and machining operations were interleaved in 1-inch intervals. We observe that the dominant texture developed during AM, resulting from different spot sizes and deposition parameters, significantly affects residual strain evolution. A dominant <011> texture along the build direction does not show any strain localization during interleaved deposition and machining whereas a dominant <001> texture shows strong tensile strain localization consistent with the pauses for machining at the end of AM step. Using coolant during machining can further alter the residual strain evolution. Our work shows that a combination of AM parameters and machining strategy can be used to influence the nature and magnitude of residual strains in components fabricated using convergent manufacturing technologies.

Hybrid manufacturing↗
DOE OSTI2025

Direct Imaging of Hydrogen‐Driven Dislocation and Strain Field Evolution in a Stainless Steel Grain

Hydrogen embrittlement (HE) poses a significant challenge to the durability of materials used in hydrogen production and utilization. Disentangling the competing nanoscale mechanisms driving HE often relies on simulations and electron-transparent sample techniques, limiting experimental insights into hydrogen-induced dislocation behavior in bulk materials. This study employs in situ Bragg coherent X-ray diffraction imaging to track three-dimensional (3D) dislocation and strain field evolution during hydrogen charging in a bulk grain of austenitic 316 stainless steel. Tracking a single dislocation reveals hydrogen-enhanced mobility and relaxation, consistent with dislocation dynamics simulations. Subsequent observations reveal dislocation unpinning and climb processes, likely driven by osmotic forces. Additionally, nanoscale strain analysis around the dislocation core directly measures hydrogen-induced elastic shielding. These findings experimentally validate theoretical predictions and offer mechanistic insights into hydrogen-driven dislocation behavior. The quantified nanoscale phenomena serve as critical inputs for multiscale modeling frameworks to predict bulk material responses and accelerate the development of HE-resistant alloys.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Comparing the deformation mechanism in 316 L stainless steel fabricated by hybrid and additive manufacturing

This study rationalizes the relatively higher elongation with minimal strength drop of 316L stainless steel (316LSS) manufactured using the hybrid approach in comparison to a fully additive approach followed by machining. It was found that twinning was the dominant deformation mechanism in 316LSS produced by both additive and hybrid approaches. Additionally, the relatively lower fraction of twins in the as-fabricated state of hybrid approach compared to a fully additive approach resulted in delaying the onset of steady-state strain hardening rate to higher strain levels, thereby resulting in an overall increase in elongation to failure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Crystallographic effects on transgranular chloride-induced stress corrosion crack propagation of arc welded austenitic stainless steel

Abstract The effect of crystallography on transgranular chloride-induced stress corrosion cracking (TGCISCC) of arc welded 304L austenitic stainless steel is studied on >300 grains along crack paths. Schmid and Taylor factor mismatches across grain boundaries (GBs) reveal that cracks propagate either from a hard to soft grain, which can be explained merely by mechanical arguments, or soft to hard grain. In the latter case, finite element analysis reveals that TGCISCC will arrest at GBs without sufficient mechanical stress, favorable crystallographic orientations, or crack tip corrosion. GB type does not play a significant role in determining TGCISCC cracking behavior nor susceptibility. TGCISCC crack behaviors at GBs are discussed in the context of the competition between mechanical, crystallographic, and corrosion factors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mechanical Properties of Additively Manufactured 316L Stainless Steel Before and After Neutron Irradiation–FY23

This report presents the observed mechanical behavior of the additively manufactured (AM) 316L stainless steel (SS) before and after neutron irradiation. In the Advanced Materials and Manufacturing Technologies (AMMT) program, a variety of mechanical and physical property data are generated and accumulated to assess the AM austenitic alloy for nuclear reactor applications. The testing and evaluation task in the FY 2023 focused on elucidating the effects of sampling location and build size on the mechanical properties of AM 316L SS (in stress-relieved condition) before and after neutron irradiation. The laser powder bed fusion (LPBF) process produced 316L plates of three distinct sizes from which SS-J3 miniature tensile specimens were machined from six different locations. The tensile specimens were irradiated in the High Flux Isotope Reactor (HFIR) normally to 2 and 10 dpa at the target temperatures of 300 °C and 600 °C. Post-irradiation tensile testing was performed at room temperature, 300 °C, and 600 °C. The mechanical properties of AM 316L SS were significantly influenced by the characteristic microstructures of printed materials, which include fine grains and high-density dislocations. Compared with the traditional 316L SS, AM 316L showed higher initial strength and lower ductility. Regardless of sampling location, the AM 316L steel retained relatively high strength and ductility to the highest irradiation dose. A prompt necking at yield (with little uniform ductility) was observed after irradiation at 300 °C but no embrittlement was observed up to 10 dpa. Ductilization by irradiation–the radiation-induced increase of ductility–was observed for the 600 °C irradiation only and it occurred in low dose range only. The neutron irradiation increased the data variation in many tensile property datasets, particularly after 600 °C irradiation, and no clear dependence of tensile properties on build thickness or sampling location was observed.

36 MATERIALS SCIENCE↗
NASA NTRS1970

Stainless steel 301 and Inconel 718 hydrogen embrittlement

Conditions and results of tensile tests of 26 Inconel 718 and four cryoformed stainless steel specimens are presented. Conclusions determine maximum safe hydrogen operating pressure for cryogenic pressure vessels and provide definitive information concerning flaw growth characteristics under the most severe temperature and pressure conditions

Allgeier, R. K.↗
NASA NTRS1981

Corrosion of 310 stainless steel in H2-H2O-H2S gas mixtures: Studies at constant temperature and fixed oxygen potential

Corrosion of SAE 310 stainless steel in H2-H2O-H2S gas mixtures was studied at a constant temperature of 1150 K. Reactive gas mixtures were chosen to yield a constant oxygen potential of approximately 6 x 10 to the minus 13th power/cu Nm and sulfur potentials ranging from 0.19 x 10 to the minus 2nd power/cu Nm to 33 x 10 to the minus 2nd power/cu Nm. The kinetics of corrosion were determined using a thermobalance, and the scales were analyzed using metallography, scanning electron microscopy, and energy dispersive X-ray analysis. Two corrosion regimes, which were dependent on sulfur potential, were identified. At high sulfur potentials (p sub S sub 2 less than or equal to 2.7 x 10 to the minus 2nd power/cu Nm) the corrosion rates were high, the kinetics obeyed a linear rate equation, and the scales consisted mainly of sulfide phases similar to those observed from pure sulfication. At low sulfur potentials (P sub S sub 2 less than or equal to 0.19 x 10 to the minus 2nd power/cu Nm) the corrosion rates were low, the kinetics obeyed a parabolic rate equation, and scales consisted mainly of oxide phases.

Rao, D. B.↗
NASA NTRS1989

Tribological reactions of perfluoroalkyl polyether oils with stainless steel under ultrahigh vacuum conditions at room temperature

The reaction between three types of commercial perfluoroalkyl polyether (PFPE) oils and stainless steel 440C was investigated experimentally during sliding under ultrahigh vacuum conditions at room temperature. It is found that the tribological reaction of PFPE is mainly affected by the activity of the mechanically formed fresh surfaces of metals rather than the heat generated at the sliding contacts. The fluorides formed on the wear track act as a boundary layer, reducing the friction coefficient.

Mori, Shigeyuki↗
NASA NTRS1993

External stress-corrosion cracking of a 1.22-m-diameter type 316 stainless steel air valve

An investigation was conducted to determine the cause of the failure of a massive AISI Type 316 stainless steel valve which controlled combustion air to a jet engine test facility. Several through-the-wall cracks were present near welded joints in the valve skirt. The valve had been in outdoor service for 18 years. Samples were taken in the cracked regions for metallographic and chemical analyses. Insulating material and sources of water mist in the vicinity of the failed valve were analyzed for chlorides. A scanning electron microscope was used to determine whether foreign elements were present in a crack. On the basis of the information generated, the failure was characterized as external stress-corrosion cracking. The cracking resulted from a combination of residual tensile stress from welding and the presence of aqueous chlorides. Recommended countermeasures are included.

Moore, Thomas J.↗
NASA NTRS1998

Comparative Stress Corrosion Cracking and General Corrosion Resistance of Annealed and Hardened 440 C Stainless Steel - New Techniques in Stress Corrosion Testing

The corrosion and stress corrosion cracking (SCC) characteristics of annealed and hardened 440C stainless steel were evaluated in high humidity and 3.5-percent NaCl solution. Corrosion testing consisted of an evaluation of flat plates, with and without grease, in high humidity, as well as electrochemical testing in 3.5-percent NaCl. Stress corrosion testing consisted of conventional, constant strain, smooth bar testing in high humidity in addition to two relatively new techniques under evaluation at MSFC. These techniques involve either incremental or constant rate increases in the load applied to a precracked SE(B) specimen, monitoring the crack-opening-displacement response for indications of crack growth. The electrochemical corrosion testing demonstrated an order of magnitude greater general corrosion rate in the annealed 440C. All techniques for stress corrosion testing showed substantially better SCC resistance in the annealed material. The efficacy of the new techniques for stress corrosion testing was demonstrated both by the savings in time and the ability to better quantify SCC data.

Mendreck, M. J.↗
DOE OSTI2020

Shock Hugoniot of forged and additively manufactured 304L stainless steel

The purpose of this research was to measure the equation of state for additively manufactured (AM) and forged 304L stainless steel. An understanding of the dynamic behavior of AM metals is integral to their timely adoption into industrial and governmental applications. The Hugoniot of the AM 304L was compared to that of the forged 304L. This comparison enabled us to determine the sensitivity of the equation of state to processing parameters and the resulting microstructure. Our results show that there is a measurable difference in the Hugoniot between the AM 304L and forged 304L. The shock wave velocities for the AM 304L were found to be slower than those for the forged 304L at similar particle speeds perhaps because of the presence of porosity in the AM 304L. While our measurements of density showed no distinct trend toward a measurable decrease in density in the AM 304L, there was a fair amount of scatter in these results.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Rate Theory Model of Radiation-Induced Swelling in an Austenitic Stainless Steel

Many rate theory models of cavity (void) swelling have been published over the past 50 years, all having the same, or similar, structures. A rigorous validation of the models has not been possible because of the dearth of information concerning the microstructures that correspond with the swelling data. Whereas the lack of microstructure information is still an issue for historical swelling data, in the past 10–20 years data have been published on the evolution of the microstructure (point defect yields from collision cascades, cavity number densities, and dislocation densities/yield strengths) allowing certain gaps in information to be filled when considering historic swelling data. With reasonable estimates of key microstructure parameters, a standard rate theory model can be applied, and the model parameter space explored, in connection with historical swelling data. By using published data on: (i) yield strength as a function of dose and temperature (to establish an empirical expression for dislocation density evolution); (ii) cavity number densities as a function of temperature; and (iii) freely migrating defect (FMD) production as a function of primary knock-on atom (PKA) spectrum, the necessary parameter and microstructure inputs that were previously unknown can be used in model development. This paper describes a rate-theory model for void swelling of 316 stainless steel irradiated in the EBR-2 reactor as a function of irradiation temperature and neutron dose.

36 MATERIALS SCIENCE↗
DOE OSTI2020

On the failure mechanisms of Cr-coated 316 stainless steel in bending fatigue tests

Here, fully-reversed cyclic bending tests were conducted on uncoated and Cr-coated 316 stainless steel specimens. At high stresses, the uncoated specimens outperformed the Cr-coated ones, while the trend reversed at low stresses. For Cr-coated specimens subjected to high stress amplitude loading, experimental observations showed crack initiation at the Cr/substrate interface due to shear steps formed from dislocation activities in the substrate—a conclusion supported by accompanying finite element analysis. Interfacial crack initiation was not observed under low stress amplitudes. This difference in fatigue crack initiation mechanisms induced an opposite trend in fatigue life between high and low stress amplitudes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Corrosion interactions between stainless steel and lead vanado-iodoapatite nuclear waste form part I

This study explores the corrosion interactions between a metallic canister material, stainless steel (SS) 316, and an I-bearing ceramic waste form, lead vanado-iodoapatite (I-APT, Pb 9.85 (VO 4 ) 6 I 1.7 ), in a chloride solution. Crevice corrosion of the SS in close proximity to the I-APT resulted in the development of an aggressive environment at the interface of the two materials, which was acidic and enriched in Cl – anions. I-APT also corroded in the crevice region, primarily through ion-exchange between the I – ions from the I-APT matrix and anions from the environment. The enrichment of Cl – anions within the occluded crevice space as the result of SS crevice corrosion enhanced the corrosion of I-APT. The release of iodine from this apatite waste form could be accelerated owing to this mechanism. This is evidenced by a depletion of iodine from the I-APT matrix and a large amount of Cl-bearing precipitates on the surfaces of both SS and I-APT. On the other hand, the corrosion of I-APT leads to the precipitation of a V- and Pb-rich layer, which inhibits the localized corrosion of SS to an extent. This study advances the understanding of the near-field corrosion interactions between metallic canisters and ceramic waste forms.

36 MATERIALS SCIENCE↗