Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stacking faults”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Effect of Mn addition on deformation behaviour of 23% Cr low nickel duplex stainless steel

Highlights: • Increasing Mn content obviously affects dynamic softening behaviour of flow curves. • More complete austenite DRX occurred with middle Mn addition of 10.3% at 1 s{sup −1}. • The constitutive equations for different Mn addition alloys are developed. • The values of activation energy and Z parameter are lowest with middle Mn addition. • Different Mn addition processing maps with increasing strain were established. - Abstract: Isothermal compression testing of 23% Cr low nickel duplex stainless steels, with different Mn concentrations, was investigated in the temperature range of 1173–1423 K, the strain rate range of 0.01–10 s{sup −1} and with a height reduction of 70%. Increasing the Mn content from 6.3 to 14.1% affected the deformation dynamic softening behaviour of flow curves at lower temperature and higher strain rate. It was also observed that increasing the deformation stain rate contributed to flow softening, and was caused by dynamic recrystallization (DRX) as a function of Mn addition. Deformation microstructure analysis demonstrated that more complete austenite phase DRX occurred with 10.3% Mn addition than that with 6.3% Mn addition at 1 s{sup −1}, but an excessive Mn content of 14.1% was unfavourable due to the increase of austenite fraction and stacking fault energy enhancement. Increasing the strain rate to 10 s{sup −1} promoted austenite phase DRX at 1323 K with the Mn addition under large strain. Meanwhile, the ferrite phase DRX occurred at 1173 K/1–10 s{sup −1} with 6.3% Mn, and was weakened with higher Mn addition. Compared to the 6.3% and 14.1% Mn, continuous DRX occurred at 1323 K/1 s{sup −1} with 10.3% Mn, due to the larger fraction of high angle misorientations. The values for the activation energy and Zener–Hollomon parameter decreased with Mn addition from 6.3 to 10.3%, and then increased with a higher Mn addition of 14.1%, indicating that a proper content of Mn addition can reduce the thermal deformation resistance and promote DRX. The constitutive equations for different Mn addition alloys were developed using a hyperbolic sine equation. Processing maps with different Mn addition for the strains of 0.3, 0.6 and 1.2 were established. The 10.3% Mn content sample corresponded to the lowest instability region, implying that the workability was improved with the middle Mn addition.

36 MATERIALS SCIENCE↗

Suppression of vacancy cluster growth in concentrated solid solution alloys

Large vacancy clusters, such as stacking-fault tetrahedra, are detrimental vacancy-type defects in ion-irradiated structural alloys. Suppression of vacancy cluster formation and growth is highly desirable to improve the irradiation tolerance of these materials. In this paper, we demonstrate that vacancy cluster growth can be inhibited in concentrated solid solution alloys by modifying cluster migration pathways and diffusion kinetics. The alloying effects of Fe and Cr on the migration of vacancy clusters in Ni concentrated alloys are investigated by molecular dynamics simulations and ion irradiation experiment. While the diffusion coefficients of small vacancy clusters in Ni-based binary and ternary solid solution alloys are higher than in pure Ni, they become lower for large clusters. This observation suggests that large clusters can easily migrate and grow to very large sizes in pure Ni. In contrast, cluster growth is suppressed in solid solution alloys owing to the limited mobility of large vacancy clusters. Finally, the differences in cluster sizes and mobilities in Ni and in solid solution alloys are consistent with the results from ion irradiation experiments.

36 MATERIALS SCIENCE↗

A Study of Tensile Flow and Work-Hardening Behavior of Alloy 617

The simple power relationship σ = Κε{sub p}{sup n} satisfactorily expresses the tensile flow behavior of many metals and alloys in their uniform plastic strain regime. However, many FCC materials with low stacking fault energy have opposed such power law relationship. Alloy 617, an age-hardenable Ni-based superalloy is also observed not to obey the simple power law relationship neither in its solution-treated nor in its aged conditions. Various flow relationships were used to obtain the best fit for the tensile data, and different relationships were identified for the different aged conditions. The work-hardening rate (θ) demonstrates three distinct regions for all aged conditions, and there is an obvious change in the trend of θ versus σ. In the initial portion, θ decreases rapidly followed by a gradual increase in the second stage and again a decrease in its third stage is perceived in the Alloy 617. These three-stage characteristics are attributed to a commonly known precipitate, γ′: Ni{sub 3}(Ti, Al) which evolves during aging treatment and well recognized under transmission electron microscopy (TEM) observation. TEM results also reveal a slight degree of coarsening in γ′ over aging. The tensile flow and the work-hardening behavior are well correlated with other microstructural evolution during the aging treatments.

36 MATERIALS SCIENCE↗

Polarized photoluminescence excitation spectroscopy of a-plane InGaN/GaN multiple quantum wells grown on r-plane sapphire

We have performed a detailed study of the impact of basal plane stacking faults (BSFs) on the optical properties of both a-plane InGaN/GaN quantum wells (QWs) and GaN template samples grown on r-sapphire. In particular, we have used polarised photoluminescence excitation spectroscopy (P-PLE) to investigate the nature of the low temperature recombination as well as extracting information on the valence band (VB) polarisation anisotropy. Our low temperature P-PLE results revealed not only excitons associated with intersubband quantum well transitions and the GaN barrier material but also a transition associated with creation of excitons in BSFs. The strength of this BSF transition varied with detection energy across the quantum well emission suggesting that there is a significant contribution to the emission line width from changes in the local electronic environment of the QWs due to interactions with BSFs. Furthermore, we observed a corresponding progressive increase in the VB splitting of the QWs as the detection energy was varied across the quantum well emission spectrum.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural Engineering of Mn-Alloyed Austenitic Steel for Hydrogen Storage and Delivery

Austenitic stainless steels are commonly used for hydrogen storage and transportation. These alloys have a high nickel (Ni) content, which increases alloy cost. In this study, high manganese (Mn) austenitic alloys were evaluated as potential lower cost alternatives. Two heats of high Mn alloys with different stacking fault energies (SFE) of ~29 mJ·m -2 and 49 mJ·m -2 were acquired. Additionally, a new vanadium (V)-microalloyed high Mn alloy was designed to achieve a SFE of 47 mJ·m -2 to minimize planar slip deformation mechanisms. Post-processing via cold working in conjunction with aging was also performed on the V-microalloyed high Mn steel. Hydrogen embrittlement sensitivity was investigated using circumferential notch tensile specimens cathodically charged with hydrogen in a 0.05M NaOH electrolytic solution. The alloys were compared to a cold-worked 316L stainless steel, which exhibited no strength loss due to hydrogen. The high Mn alloys with SFE of ~29 mJ·m 2 and 49 mJ·m -2 had notch strength losses of 11 and 6 pct, respectively. The V-microalloyed high Mn steel in the as-hot-rolled condition had a notch strength loss of 17 pct. Furthermore, the V-microalloyed high Mn steel in the cold worked and aged condition indicated no notch strength loss in hydrogen, which was comparable to the performance of the 316L stainless steel.

36 MATERIALS SCIENCE↗

Mechanical behavior of a composite interface: Calcium-silicate-hydrates

The generalized stacking fault (GSF) is a conceptual procedure historically used to assess shear behavior of defect-free crystalline structures through molecular dynamics or density functional theory simulations. We apply the GSF technique to the spatially and chemically complex quasi-layered structure of calcium-silicate-hydrates (C-S-H), the fundamental nanoscale binder within cementitious materials. A failure plane is enforced to calculate the shear traction-displacement response along a composite interface containing highly confined water molecules, hydroxyl groups, and calcium ions. GSF simulations are compared with affine (homogeneous) shear simulations, which allow strain to localize naturally in response to the local atomic environment. Comparison of strength and deformation behavior for the two loading methods shows the composite interface controls bulk shear deformation. Both models indicate the maximum shear strength of C-S-H exhibits a normal-stress dependency typical of cohesive-frictional materials. These findings suggest the applicability of GSF techniques to inhomogeneous structures and bonding environments, including other layered systems such as biological materials containing organic and inorganic interfaces.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Bamboo-like 3C-SiC nanowires with periodical fluctuating diameter: Homogeneous synthesis, synergistic growth mechanism, and their luminescence properties

Herein, bamboo-like 3C-SiC nanowires have been successfully fabricated on homogeneous 6H-SiC substrate by a simple chemical vapor reaction (CVR) approach. The obtained 3C-SiC nanostructure with periodical fluctuating diameter, is composed of two alternating structure units, the typical normal-sized stem segment with perfect crystallinity and obvious projecting nodes segment having high-density stacking faults. The formation of the interesting morphology is significantly subjected to the peculiar growth condition provided by the homogeneous substrate as well as the varying growth elastic energy. Furthermore, the photoluminescence (PL) performance measured on the bamboo-like SiC nanowire shows an intensive emission peaks centered at 451 nm and 467 nm, which has been expected to make a positive progress toward the optical application of the SiC-based one-dimensional (1D) nanostructures, such as light emission diode (LED). - Graphical abstract: Based on the synergistic growth mechanism from homogeneous substrate and elastic energy, bamboo-like 3C-SiC nanowires with periodically fluctuating diameter have been synthesized on 6H-SiC. The blue-violet light emission properties of the bamboo-like nanowires have also been investigated for exploring their peculiar optical application. - Highlights: • Bamboo-like 3C-SiC nanowires with periodically fluctuating diameter have been synthesized on 6H-SiC. • A synergistic growth mechanism from homogeneous substrate and elastic energy has been proposed firstly. • The blue-violet light emission properties of the products displayed peculiar optical application.

36 MATERIALS SCIENCE↗

Characterization of Metamorphic GaAsP/Si Materials and Devices for Photovoltaic Applications

GaAsyP{sub 1-y} anion-sublattice compositionally graded buffers and device structures were grown directly on Si(100) substrates by way of a high-quality GaP integration layer, yielding GaAsP target layers having band gaps of photovoltaic interest (1.65-1.8 eV), free of antiphase domains/borders, stacking faults, and microtwins. GaAsyP{sub 1-y} growths on both Si and GaP substrates were compared via high-resolution X-ray diffractometry of the metamorphic buffers and deep-level transient spectroscopy (DLTS) of p{sup +}-n diodes that are lattice matched to the final buffer layer. Structural analysis indicates highly efficient epitaxial relaxation throughout the entire growth structure for both types of samples and suggests no significant difference in physical behavior between the two types of samples. DLTS measurements performed on GaAsP diodes fabricated on both Si and GaP substrates reveal the existence of identical sets of traps residing in the n-type GaAsP layers in both types of samples: a single majority carrier (electron) trap, which is located at EC - 0.18 eV, and a single minority carrier (hole) trap, which is located at EV + 0.71 eV. Prototype 1.75-eV GaAsP solar cell test devices grown on GaAsyP{sub 1-y}/Si buffers show good preliminary performance characteristics and offer great promise for future high-efficiency III-V photovoltaics integrated with Si substrates and devices.

14 SOLAR ENERGY↗

The influence of temperature on the strain-hardening behavior of Fe-22/25/28Mn-3Al-3Si TRIP/TWIP steels

In this work, the influence of temperature and stacking fault energy (SFE) on the strain-hardening behavior and critical resolved shear stress for twinning was investigated for three Fe–22/25/28Mn–3Al–3Si wt.% transformation- and twinning-induced plasticity (TRIP/TWIP) steels. The SFEs were calculated by two different methods, density functional theory and statistical thermodynamic modeling. The dislocation structure, observed at low levels of plastic deformation, transitions from “planar” to “wavy” dislocation glide with an increase in temperature, Mn content, and/or SFE. The change in dislocation glide mechanisms from planar to wavy reduces the strain hardening rate, in part due to fewer planar obstacles and greater cross slip activity. Additionally, the alloys exhibit a large decrease in strength and ductility with increasing temperature from 25 to 200 °C, attributed to a substantial reduction in the thermally activated component of the flow stress, predominate suppression of TRIP and TWIP, and a significant increase in the critical resolved shear stress for mechanical twinning. Interestingly, the increase in SFE with temperature had a rather minor influence on the critical resolved shear stress for mechanical twinning, and other temperature dependent factors which likely play a more dominant role are discussed.

36 MATERIALS SCIENCE↗

Effect of short-range order on microstructure, texture and strain hardening of cold drawn Cu-10 at.%Mn alloy

Highlights: • Excluding the effect of stacking fault energy, short-range order effect is discussed solely. • Short-range order is beneficial for twinning and slip planarity. • Short-range order promotes the formation of <111> fiber texture. • Strain hardening improving by short-range order. - Abstract: The aim of the present study is to investigate the effect of short-range order (SRO) on the microstructural evolution and mechanical property of Cu-10 at.%Mn alloy during cold drawing deformation. Characterization of the cold drawn Cu-10 at.%Mn alloy samples were performed using transmission electron microscope (TEM) and electron back scattering diffraction (EBSD), and their hardness were also tested. The results show that SRO is beneficial for both twinning and the transition of dislocation glide from wavy slip to planar slip at the low strains. At the high strains, the wavy slip generates due to the destruction of SRO. SRO increases the volume fraction of <111> texture component and the critical strain threshold. Moreover, the presence of SRO significantly improves strain hardening by combining the effects of dislocation, deformation twinning and texture hardening, which results in a significant increase of hardness.

36 MATERIALS SCIENCE↗

Phase transformation and optical properties of Cu-doped ZnS nanorods

ZnS nanorods doped with 0-15 mol% of Cu have been prepared by simple solvothermal process. With gradual increase in the Cu concentration, phase transformation of the doped ZnS nanorods from wurtzite to cubic was observed. Twins and stacking faults were developed due to atomic rearrangement in the heavily doped ZnS nanorods during phase transformation. UV-vis-NIR absorbance spectroscopy ruled out the presence of any impure Cu-S phase. The doped ZnS nanorods showed luminescence over a wide range from UV to near IR with peaks at 370, 492-498, 565 and 730 nm. The UV region peak is due to the near-band-edge transition, whereas, the green peak can be related to emission from elementary sulfur species on the surfaces of the nanorods. The orange emission at 565 nm may be linked to the recombination of electrons at deep defect levels and the Cu(t{sub 2}) states present near the valence band of ZnS. The near IR emission possibly originated from transitions due to deep-level defects. - Graphical abstract: ZnS nanorods doped with 0-15 mol% of Cu has been prepared by simple solvothermal route. Interestingly, phase transformation of the doped ZnS nanorods from wurtzite to cubic was observed with gradual increase in the Cu concentration. Doped ZnS nanorods showed luminescence over a wide range from UV to near IR, which is also a rare observation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Formation of deformation textures in face-centered-cubic materials studied by in-situ high-energy x-ray diffraction and self-consistent model.

The evolution of deformation textures in copper and a brass that are representative of fcc metals with different stacking fault energies (SFEs) during cold rolling is predicted using a self-consistent (SC) model. The material parameters used for describing the micromechanical behavior of each metal are determined from the high-energy X-ray (HEXRD) diffraction data. At small reductions, a reliable prediction of the evolution of the grain orientation distribution that is represented as the continuous increase of the copper and brass components is achieved for both metals when compared with the experimental textures. With increasing deformation, the model could characterize the textures of copper, i.e., the strengthening of the copper component, when dislocation slip is still the dominant mechanism. For a brass at moderate and large reductions, a reliable prediction of its unique feature of texture evolution, i.e., the weakening of the copper component and the strengthening of the brass component, could only be achieved when proper boundary conditions together with some specified slip/twin systems are considered in the continuum micromechanics mainly containing twinning and shear banding. The present investigation suggests that for fcc metals with a low SFE, the mechanism of shear banding is the dominant contribution to the texture development at large deformations.

36 MATERIALS SCIENCE↗

Understanding the deformation behavior of the γ rich transformative Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy using in situ synchrotron diffraction

In situ tensile testing coupled with synchrotron x-ray diffraction was used to study the deformation behavior of metastability-engineered Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy. Monitoring the evolution of phase fraction and strain hardening response allowed the determination of true critical stress for the onset of the transformation-induced plasticity (TRIP) to be ∼375 MPa, preceded by slip starting at ∼255 MPa. In situ EBSD was used to validate the critical stress for transformation at the microstructure level and observe slip traces to confirm prior slip activity before the transformation. Further, a modeling framework based on stacking fault energy (SFE) was developed to predict the critical stress for transformation. Modeling suggested the SFE of the alloy to fall nearly 15 mJ/m 2 , which agrees well with SFE values calculated using synchrotron peak shifting (12 mJ/m 2 ) and thermodynamic calculation (11 mJ/m 2 ). As a result of γ-fcc to ε-hcp phase transformation, new {0002} ε planes emerged parallel to unaligned {111} γ planes with the tensile loading following S-N orientation relationship. Such selective emergence of new diffraction rings corresponding to ε phase is understood based on the reorientation of γ crystals with reference to tensile axis. In conclusion, this approach can be extended to effectively design alloys based on critical stress required for activating different deformation mechanisms to further push the limits of the strength-ductility envelope.

Complex concentrated alloy↗

Quantitative description of microstructure defects in hexagonal boron nitrides using X-ray diffraction analysis

A routine for simultaneous quantification of turbostratic disorder, amount of puckering and the dislocation and stacking fault density in hexagonal materials was proposed and tested on boron nitride powder samples that were synthesised using different methods. The routine allows the individual microstructure defects to be recognised according to their effect on the anisotropy of the X-ray diffraction line broadening. For quantification of the microstructure defects, the total line broadening is regarded as a linear combination of the contributions from the particular defects. The total line broadening is obtained from the line profile fitting. As testing material, graphitic boron nitride (h-BN) was employed in the form of hot-isostatically pressed h-BN, pyrolytic h-BN or a h-BN, which was chemically vapour deposited at a low temperature. The kind of the dominant microstructure defects determined from the broadening of the X-ray diffraction lines was verified by high resolution transmission electron microscopy. Their amount was attempted to be verified by alternative methods. - Highlights: • Reliable method for quantification of microstructure defects in BN was suggested. • The method is based on the analysis of anisotropic XRD line broadening. • This XRD line broadening is unique and characteristic of the respective defect. • Thus, the quantification of coexistent microstructure defects is possible. • The method was tested on hexagonal BN, which was produced by different techniques.

36 MATERIALS SCIENCE↗

Influences of defects evolvement on the properties of sputtering deposited ZnO:Al films upon hydrogen annealing

Understanding how the defects interact with each other and affect the properties of ZnO:Al films is very important for improving their performance as a transparent conductive oxide (TCO). In the present work, we studied the effects of hydrogen annealing on the structural, optical and electrical properties of ZnO:Al films prepared by magnetron sputtering. High resolution transmission electron microscopy observations reveal that annealing at ∼300 {sup o}C induces the formation of partial dislocations (PD) and stacking faults (SF), which disrupt the lattice periodicity leading to decreased grain size. Annealing at temperatures above ∼500 {sup o}C can remove the PD and SF, but large number of zinc vacancies will be generated. Our results show that when films are annealed at ∼500 {sup o}C, the oxygen-related defects (interstitials O{sub i}, etc.) in the as-grown films can be remarkably removed or converted, which lead to increments in the carrier concentration, mobility, and the transmittance in the visible range. At annealing temperatures above 550 {sup o}C, the hydrogen etching effect becomes predominant, and Al donors are deactivated by zinc vacancies. We also find an abnormal endothermic process by thermal analysis and an abnormal increase in the resistivity during heating the sample under hydrogen atmosphere, based on which the interaction of O{sub i} with the defects (mainly Al donors and PD) is discussed. It is also demonstrated that by annealing the as-grown AZO films at ∼500 {sup o}C under hydrogen atmosphere, high performance TCO films with a low resistivity of 4.48 × 10{sup −4} Ωcm and high transmittance of above 90% in the visible light are obtained.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Temperature-Dependent Mechanical Properties of Ni-Based Concentrated Alloys: Insights from First-Principles Calculations

The present work focuses on predicting temperature-dependent mechanical properties of Ni-based concentrated alloys Ni 18 Cr 10 Co 10 Fe 6 M 4 (abbreviated by X 44 M 4 , with M = Al, V, Mn, Fe, Nb, Mo, and W) using density functional theory (DFT). These predictions are based on shear (plastic) and elastic deformations, utilizing the special quasirandom structure (SQS), the phonon-based quasiharmonic approach (QHA), and the quasistatic approach. The resulting properties include coefficient of thermal expansion via QHA, ideal shear strength (τ IS ), and stable and unstable stacking fault energies (γ SF and γ US ) through pure alias shear deformation, and elastic constants (c ij ), bulk modulus (B 0 ), and shear modules (G 0 ) via elastic deformation. Notably, predicting accurate γ SF is challenging due to uncertainties that can exceed the γ SF values. τ IS and γ US exhibit a strong linear relationship, enabling the accurate prediction of γ US based on the precisely determined τ IS . All mechanical properties of X 44 M 4 decrease with increasing temperature, except for some γ SF cases such as X 44 M 4 with M = V, Mn, Fe, Mo, and W. Among the X 44 M 4 alloys, X 44 Nb 4 exhibits the lowest τ IS , γ US , and G 0 values, and the highest B 0 /G 0 ratio, while X 44 Mn 4 has the lowest B 0 and B 0 /G 0 ratio. We found that volume is a crucial descriptor for understanding and modeling mechanical properties (except B0 and maybe also γ SF ) affected by alloying elements and temperature. Ni-based dilute alloys (e.g., Ni 11 M 1 and Ni 31 M 1 ) and concentrated alloys (e.g., X 44 M 4 ) show similar trends in mechanical properties influenced by alloying elements and temperature, simplifying the analysis and design of Ni-based alloys.

Elastic properties↗

Effects of strain rate on mechanical properties and deformation behavior of an austenitic Fe-25Mn-3Al-3Si TWIP-TRIP steel

The effects of quasi-static and low-dynamic strain rate (ε = 10 –4 /s to ε = 10 2 /s) on tensile properties and deformation mechanisms were studied in a Fe-25Mn-3Al-3Si (wt%) twinning and transformation-induced plasticity [TWIP-TRIP] steel. The fully austenitic microstructure deforms primarily by dislocation glide but due to the room temperature stacking fault energy [SFE] of 21 ± 3 mJ/m 2 for this alloy, secondary deformation mechanisms such as mechanical twinning (TWIP) and epsilon martensite formation (TRIP) also play an important role in the deformation behavior. The mechanical twins and epsilon-martensite platelets act as planar obstacles to subsequent dislocation motion on non-coplanar glide planes and reduce the dislocation mean free path. A high-speed thermal camera was used to measure the increase in specimen temperature as a function of strain, which enabled the use of a thermodynamic model to predict the increase in SFE. The influence of strain rate and strain on microstructural parameters such as the thickness and spacing of mechanical twins and epsilon-martensite laths was quantified using dark field transmission electron microscopy, electron channeling contrast imaging, and electron backscattered diffraction. The effect of sheet thickness on mechanical properties was also investigated. Increasing the tensile specimen thickness increased the product of ultimate tensile strength and total elongation, but had no significant effect on uniform elongation or yield strength. The yield strength exhibited a significant increase with increasing strain rate, indicating that dislocation glide becomes more difficult with increasing strain rate due to thermally-activated short-range barriers. Finally, a modest increase in ultimate tensile strength and minimal decrease in uniform elongation were noted at higher strain rates, suggesting adiabatic heating, slight changes in strain-hardening rate and observed strain localizations as root causes, rather than a significant change in the underlying TWIP-TRIP mechanisms at low values of strain.

36 MATERIALS SCIENCE↗

High-Efficiency Non-Polar GaN-Based LEDs

Inlustra Technologies with subcontractor U.C. Santa Barbara conducted a project with the principle goal of demonstrating high internal quantum efficiency blue (430 nm) and green (540nm) light emitting diodes (LEDs) on low-defect density non-polar GaN wafers. Inlustra pursued the fabrication of smooth thick a-plane and m-plane GaN films, as well as defect reduction techniques such as lateral epitaxial overgrowth (LEO) to uniformly lower dislocation density in these films. Limited free-standing wafers were produced as well. By the end of the reporting period, Inlustra had met its milestone of dislocation reduction to < 5 x 10{sup 6} cm{sup -2}. Stacking faults were still present in appreciable density ({approx} 1 x 10{sup 5} cm{sup -1}), but were not the primary focus of defect reduction since there have been no published studies establishing their detrimental effects on LED performance. Inlustra's LEO progress built a solid foundation upon which further commercial development of GaN substrates will occur. UCSB encountered multiple delays in its LED growth and fabrication efforts due to unavoidable facilities outages imposed by ongoing construction in an area adjacent to the metalorganic chemical vapor deposition (MOCVD) laboratory. This, combined with the large amount of ab initio optimization required for the MOCVD system used during the project, resulted in unsatisfactory LED progress. Although numerous blue-green photoluminescence results were obtained, only a few LED structures exhibited electroluminescence at appreciable levels. UCSB also conducting extensive modeling (led by Prof. Van de Walle) on the problem of non-radiative Auger recombination in GaN-based LED structures, which has been posited to contribute to LED efficiency 'droop' at elevated current density. Unlike previous modeling efforts, UCSB's approach was truly a first-principles ab initio methodology. Building on solid numerical foundations, the Auger recombination rates of In{sub x}Ga{sub 1-x}N alloys were calculated from first-principles density-functional and many-body-perturbation theory. The differing mechanisms of inter- and intra-band recombination were found to affect different parts of the emission spectrum. In the blue to green spectral region and at room temperature the Auger coefficient was calculated to be as large as 2 x 10{sup -30} cm{sup 6} s{sup -1}; in the infrared it is even larger. These results indicated that Auger recombination may be responsible for the loss of quantum efficiency that affects InGaN-based light emitters, whether on non-polar or polar crystal planes.

36 MATERIALS SCIENCE↗