Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solubility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Uranyl nitrate hexahydrate solubility in nitric acid and its crystallization selectivity in the presence of nitrate salts

The solubility of uranyl nitrate hexahydrate was determined as a function of nitric acid concentration and temperature, and the crystallization yield was calculated. Results showed an increase in crystal formation at lower initial nitric acid concentrations upon cooling a saturated solution of U(VI) from 50 °C to 2 °C, with over 70% recovery of U(VI) mass at all nitric acid concentrations and nearly quantitative recovery starting at 4 M HNO 3 . A direct correlation between the change in mother liquor volume percent and U mass removal percent was observed. By reducing the cooling rate from roughly 4.0 °C/min to 0.22 °C/min, the separation factor was increased from 3.88 to 15.7 to greater than 81 for the separation of U(VI) from Sr, Cs, and Nd. At the slower cooling rate, the separation factors were measured as a function of acidity for 2.0–4.3 M HNO 3 , showing a decrease in selectivity with a decrease in the acidity. There was also no indication that tetravalent metal double-salt precipitation occurred with either Zr 4+ or Ce 4+ . Here, these results indicate that a high-yield, high purity hexavalent actinide crystallization scheme may offer attractive benefits for nuclear-fuel recycle in that only a single very simple and well-understood technology is employed, and the use of organic compounds and solvents is avoided.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Crystal growth methods dedicated to low solubility actinide oxalates

Two novel crystal growth syntheses dedicated to low solubility actinide-oxalate systems and adapted to glove box handling are described. These methods based on the use of precursors of either actinide metal or oxalic acid have been optimized on lanthanide systems (analogue of actinides(III)) and then assessed on real actinide systems. They allow the synthesis of several actinide oxalate single crystals, Am{sub 2}(C{sub 2}O{sub 4}){sub 3}(H{sub 2}O){sub 3}·xH{sub 2}O, Th(C{sub 2}O{sub 4}){sub 2}·6H{sub 2}O, M{sub 2+x}[Pu{sup IV}{sub 2−x}Pu{sup III}{sub x}(C{sub 2}O{sub 4}){sub 5}]·nH{sub 2}O and M{sub 1−x}[Pu{sup III}{sub 1−x}Pu{sup IV}{sub x}(C{sub 2}O{sub 4}){sub 2}·H{sub 2}O]·nH{sub 2}O. It is the first time that these well-known compounds are formed by crystal growth methods, thus enabling direct structural studies on transuranic element systems and acquisition of basic data beyond deductions from isomorphic (or not) lanthanide compounds. Characterizations by X-ray diffraction, UV–visible solid spectroscopy, demonstrate the potentialities of these two crystal growth methods to obtain oxalate compounds. - Graphical abstract: Two new single crystal growth methods dedicated to actinide oxalate compounds. - Highlights: • Use of diester as oxalate precursor for crystal growth of actinide oxalates. • Use of actinide oxide as precursor for crystal growth of actinide oxalates. • Crystal growth of Pu(III) and Am(III) oxalates. • Crystal growth of mixed Pu(III)/Pu(IV) oxalates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2013

Characterization and biodegradation of water-soluble biomarkers and organic carbon extracted from low temperature chars

This study demonstrates that wildfires/biomass combustion may be an important source of labile pyrogenic water-soluble organic matter (Py-WSOM) to aquatic systems. Spectroscopic analysis (of the solid char and Py-WSOM) with Fourier transform infrared spectroscopy (FTIR) indicated that the Py-WSOM extracted from two low temperature chars (one wood, one grass) was dominated by polar moieties (-OH and C-O) derived from depolymerization and fragmentation of lignocellulose. Incubation experiments under aerobic conditions with unsterilized river water suggested that Py-WSOM and associated biomarkers may have turnover rates on the order of weeks to months, consistent with mixing and transport conditions of riverine systems. For example, pyrogenic dissolved organic carbon (Py-DOC) had a half-life of 30-40 days. Turnover rate for the combustion biomarkers was shorter, with levoglucosan and free lignin phenols having a half-life around 3-4 days and polymeric lignin components 13-14 days. The latter observations contradict earlier studies on the biodegradation of dissolved lignin and point to the need for re-assessment of lignin degradation kinetics in well-mixed riverine systems, particularly when such lignin components are derived from thermally altered plant material that may exist in a form more labile than that in highly processed riverine DOM.

low temperature charcoals, pyrogenic carbon, water↗
DOE OSTI2022

Crystalline phase transitions and water-soluble complexes of copper(Ⅰ) 2-hydroxyethanethiolate

We report the coordination polymer copper(I) 2-hydroxyethanethiolate, (CuSCH 2 CH 2 OH) n , though insoluble in all common solvents, dissolved readily in basic aqueous solutions of the thiolate anion (HOCH 2 CH 2 S – ) of 2-mercaptoethanol to form a single species: the tetranuclear cluster [Cu 4 (μ-SCH 2 CH 2 OH) 6 ] 2– . From this solution were grown X-ray quality single crystals of copper(I) 2-hydroxyethanethiolate. This compound underwent a hitherto unknown crystal phase transition at ca. 6 °C, from point group P2 1 2 1 2 1 to Pna2 1 , with noticeable changes in the geometry of the Cu-S layer and in the orientation of the alkylthiolate side chains. When the bulky base tetrabutylammonium hydroxide was employed in the aqueous thiolate solution used to dissolve (CuSCH 2 CH 2 OH) n , the water-soluble polynuclear copper(I) complex bis(tetrabutylammonium) hexakis(μ-2-hydroxyethanethiolato) tetracuprate(I), [(C 4 H 9 ) 4 N] 2 [Cu 4 (μ-SCH 2 CH 2 OH) 6 ], could be isolated as X-ray quality crystals. Structural characterization of this complex revealed a tetrahedral arrangement of copper(I) centers with thiolates bridging the edges of the tetrahedra. On standing, this complex degraded to a larger polynuclear Cu(I) sulfide cluster.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Electrolyte with Low Polysulfide Solubility for Li-S Batteries

Here, Li-S battery is one of the most promising next generation rechargeable battery technologies due to its high theoretical energy density and low material cost. While its success is impeded by the low energy efficiency and fast capacity fade primarily caused by the discharge intermediates, Li-polysulfides (PS), dissolution in the electrolyte. Mitigation of PS dissolution in electrolyte involves the search of new electrolyte solvent system that exhibits poor solvation to the PS while still have good solvation ability to the electrolyte salt for high ionic conductivity. Applying co-solvents with reduced solvating power but compatible with the state of art Li-S battery’s ether-based electrolyte is one of the most promising concepts. This route is also advantageous of having a low scale-up cost. With the aids of Quantum Chemical Calculation, we have identified high carbon-to-oxygen (C/O) ratio ethers as co-solvent in the new electrolytes that effectively impede PS dissolution while still maintaining high ionic conductivity. Significantly improved cycle life and cycling Coulombic efficiency are observed for Li-S cells using the new composite electrolytes. Anode analysis with different methods also demonstrate that reducing electrolyte’s PS solubility results in less sulfur total amount on the lithium anode surface and lower ratio of the longer-chain PS, which is probably a sign of suppressed side reactions between the anode and PS in the electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2022

High Energy Density Aqueous Flow Battery Utilizing Extremely Stable, Branching-Induced High-Solubility Anthraquinone near Neutral pH

An anthraquinone featuring a chiral carboxylate-capped methyl-branched side chain with an ether linkage, 2,2'-((9,10-dioxo-9,10-dihydroanthracene-2,6-diyl)bis(oxy))dipropionic acid (2,6-D2PEAQ), was synthesized and evaluated for use in aqueous redox flow batteries. It was found to have an extraordinary solubility of 2 M (4 M electrons), corresponding to a theoretical volumetric capacity of 107.2 Ah/L for the negative electrolyte, which is 10 times that of its unbranched counterpart. The 2,6-D2PEAQ molecule demonstrated stability against thermal 2 decomposition and was extremely stable under cell cycling conditions. Here, a capacity fade rate of 0.02% day over 14 days was demonstrated in a 1.1 M 2,6-D2PEAQ nearly capacity-balanced cell when paired with a ferro-/ferricyanide posolyte at pH 7. Compared to other aqueous redoxactive organic molecules, its demonstrated fade rate is lower than that of any molecule with a demonstrated volumetric capacity of ≥55 Ah/L, and its volumetric capacity is greater than that of any molecule with a demonstrated fade rate of ≤0.5%/day.

25 ENERGY STORAGE↗
DOE OSTI2015

Real-Time Observation of Water-Soluble Mineral Precipitation in Aqueous Solution by In Situ High-Resolution Electron Microscopy

The precipitation and dissolution of water-soluble minerals in aqueous systems is a familiar process occurring commonly in nature. Understanding mineral nucleation and growth during its precipitation is highly desirable, but past in situ techniques have suffered from limited spatial and temporal resolution. In this paper, by using in situ graphene liquid cell electron microscopy, mineral nucleation and growth processes are demonstrated in high spatial and temporal resolution. We precipitate the mineral thenardite (Na 2 SO 4 ) from aqueous solution with electron-beam-induced radiolysis of water. We demonstrate that minerals nucleate with a two-dimensional island structure on the graphene surfaces. We further reveal that mineral grains grow by grain boundary migration and grain rotation. Finally, our findings provide a direct observation of the dynamics of crystal growth from ionic solutions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2012

Enhanced dopant solubility and visible-light absorption in Cr-N co-doped TiO2 nanoclusters

A major obstacle toward employing TiO2 as an efficient photoactive material is related to its large optical band gap, strongly limiting visible light absorption. Substitutional doping with both donors and acceptors (co-doping) potentially leads to a significant band gap reduction, but the effectiveness of the co-doping approach remains limited by the low solubility of dopants inside TiO2. Here we show that nanostructured Cr and N co-doped TiO2 thin films can be obtained by Supersonic Cluster Beam Deposition (SCBD) with a high concentration of dopants and a strongly reduced band gap. Complementary spectroscopic investigations show that doping effectively occurs into substitutional lattice sites, inducing dopant levels in the gap that are remarkably delocalized. The high surface-to-volume ratio, typical of SCBD nanostructured films, likely facilitates the dopant incorporation. The present results indicate that SCBD films are highly promising photoactive nanophase materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

Growth of high quality bulk size single crystals of inverted solubility lithium sulphate monohydrate

The paper summarizes the processes of growing large lithium sulfate monohydrate (LSMH) single crystals. We have established a procedure to grow high quality bulk size single crystals of inverted solubility LSMH by a newly developed unidirectional crystallization technique called the Sankeranarayenan - Ramasamy (SR) method. The convective flow of crystal growth processes from solution and the conditions of growing crystals of various aspects were discussed. Good quality LSMH single crystal is grown of the size 20 mmX80 mm without cracks, localized-defects and inclusions. The as-grown crystals are suitable for piezoelectric and nonlinear optical applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

A molecular dynamics study of water-soluble polymers: analysis of force fields from atomistic simulations

A force field (FF) analysis was performed on three water-soluble polymers (PAM, PNIPAAm, and PEO), that are of significant interest for biomedical applications, by measuring the polymer radius of gyration ( R g ), solvent accessible surface area (SASA), radial distribution functions ( g ( r )), and relative shape anisotropy ( κ 2 ) in dilute conditions. Three generalized FFs were utilized to model PAM and PNIPAAm (DREIDING, GAFF, and GAFF2) in conjunction with five water models: SPC, SPC/E, TIP3P, TIP4P, and TIP4P/2005. It was found that the DREIDING FF showed better agreement with PAM experimental data reported for R g , irrespective of the water model. For PNIPAAm, the DREIDING FF was also the best performing among the FFs studied; however, the choice of water model played an important role in the predicted properties. The trends in SASA and κ 2 are consistent with R g . For PEO modelled with the CHARMM C35r FF, all water models except TIP3P resulted in good agreement with experimental and previous simulation data. Furthermore these results highlight the considerable impact that polymer and water force fields can have on sampling appropriate polymer conformations in solvated systems.

36 MATERIALS SCIENCE↗
DOE OSTI2016

α, α', α", α'"- meso -tetrahexyltetramethyl-calix[4]pyrrole: An easy-to-prepare, isomerically pure anion extractant with enhanced solubility in organic solvents

α, α', α", α'"- meso -Tetrahexyltetramethyl-calix[4]pyrrole is easily obtained as a single diastereomer in a one-pot reaction. It exhibits enhanced solubility in organic solvents, including aliphatic solvents, relative to its parent meso-octamethylcalix[4]pyrrole (1). Somewhat surprisingly, the tetrahexyl derivative 2 complexes with tributylmethylammonium chloride in chloroform more strongly than does 1 as shown by NMR titrations. However, 1 and 2 exhibit comparable complexation strength in extraction experiments, the difference between the NMR and extraction results being attributed to the effect of organic-phase water in the extraction systems. Mass-action analysis indicates the formation of the predominant complex TBMA + (1 or 2)Cl – in both NMR and extraction systems, and equilibrium constants are reported. x-Ray crystal structures were obtained for the free ligand 2 and its complex with tetramethylammonium chloride. In addition, the free ligand crystallises in the 1,3-alt conformation with equatorial hexyl arms. In the chloride complex with 2 in its cone conformation, the hexyl arms adopt an axial orientation, enveloping the anion. DFT calculations show this binding conformation to be the most stable, mostly owing to destabilising steric interactions involving the pyrrole C–H and alkyl C–H groups positioned equatorially.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

AB initio free energy calculations of the solubility of silica in metallic hydrogen and application to giant planet cores

By combining density functional molecular dynamics simulations with a thermodynamic integration technique, we determine the free energy of metallic hydrogen and silica, SiO{sub 2}, at megabar pressures and thousands of degrees Kelvin. Our ab initio solubility calculations show that silica dissolves into fluid hydrogen above 5000 K for pressures from 10 and 40 Mbars, which has implications for the evolution of rocky cores in giant gas planets like Jupiter, Saturn, and a substantial fraction of known extrasolar planets. Our findings underline the necessity of considering the erosion and redistribution of core materials in giant planet evolution models, but they also demonstrate that hot metallic hydrogen is a good solvent at megabar pressures, which has implications for high-pressure experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Applications of the second virial coefficient: protein crystallization and solubility

This article highlights some of the ground-based studies emanating from NASA’s Microgravity Protein Crystal Growth (PCG) program, and includes a more detailed discussion of the history and the progress made in one of the NASA-funded PCG investigations involving the use of measured second virial coefficients (B values) as a diagnostic indicator of solution conditions conducive to protein crystallization. This article begins by highlighting some of the ground-based studies emanating from NASA’s Microgravity Protein Crystal Growth (PCG) program. This is followed by a more detailed discussion of the history of and the progress made in one of the NASA-funded PCG investigations involving the use of measured second virial coefficients (B values) as a diagnostic indicator of solution conditions conducive to protein crystallization. A second application of measured B values involves the determination of solution conditions that improve or maximize the solubility of aqueous and membrane proteins. These two important applications have led to several technological improvements that simplify the experimental expertise required, enable the measurement of membrane proteins and improve the diagnostic capability and measurement throughput.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Enhancing the solubility of SARS-CoV-2 inhibitors to increase future prospects for clinical development

SARS-CoV-2 poses an ongoing threat to human health as variants continue to emerge. Several effective vaccines are available, but a diminishing number of Americans receive the updated vaccines (only 22% received the 2023 update). Public hesitancy towards vaccines and common occurrence of “breakthrough” infections (i.e., infections of vaccinated individuals) highlight the need for alternative methods to reduce viral transmission. SARS-CoV-2 enters cells by fusing its envelope with the target cell membrane in a process mediated by the viral spike protein, S. The S protein operates via a Class I fusion mechanism in which fusion between the viral envelope and host cell membrane is mediated by structural rearrangements of the S trimer. We previously reported lipopeptides derived from the C-terminal heptad repeat (HRC) domain of SARS-CoV-2 S that potently inhibit fusion by SARS-CoV-2, both in vitro and in vivo. These lipopeptides bear an attached cholesterol unit to anchor them in the membrane. Here, to improve prospects for experimental development and future clinical utility, we employed structure-guided design to incorporate charged residues at specific sites in the peptide to enhance aqueous solubility. This effort resulted in two new, potent lipopeptide inhibitors.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Hydrogen solubility in amorphous Mg{sub 0.6}SiO{sub 2.6} at high pressure

The solubility of hydrogen in amorphous Mg{sub 0.6}SiO{sub 2.6} at a temperature of 250°C and pressures up to 75 kbar is studied using a quenching technique. The molar ratio H{sub 2}/formula unit is found to nonlinearly increase with pressure from x = 0.12 at P = 10 kbar to x = 0.303 at P = 75 kbar. An investigation of the quenched samples by Raman spectroscopy demonstrated that hydrogen dissolves in amorphous Mg{sub 0.6}SiO{sub 2.6} in the form of H{sub 2} molecules. X-ray diffraction and Raman studies showed that the hydrogenation of the samples is likely to be accompanied by a phase transition in the amorphous lattice of Mg{sub 0.6}SiO{sub 2.6} at P ≈ 52.5 kbar to a denser amorphous modification.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Influence of Annealing on the Properties of Ge:Sb/Si(001) Layers with an Antimony Concentration Above Its Equilibrium Solubility in Germanium

The influence of rapid thermal annealing on the electrical and radiative properties of Ge:Sb/Si(001) epitaxial layers with an antimony concentration substantially higher than its equilibrium solubility in germanium is investigated. Local variations in the electrical and luminescence properties of n-Ge/Si(001) throughout the structure depth are investigated by means of the precise chemical etching of Ge. It is shown that a variation in the properties of such layers at relatively low (≤500°C) annealing temperatures (decrease in the electron concentration and photoluminescence intensity) occur in the absence of the noticeable diffusion-related redistribution of dopant atoms. Variations in the electrical and luminescence properties of Ge:Sb layers at relatively high (≥700°C) annealing temperatures are caused by the substantial redistribution of Sb due to its bulk diffusion and desorption from the surface. In particular, Sb diffusion leads to the formation of doped layers in initially undoped parts of the studied structures, which start to give a substantial contribution to the resulting conductivity of the structure and its photoluminescence signal.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Tellurium Solubility in TlGaTe{sub 2} and TlInTe{sub 2} and the Electrophysical Properties of Solid Solutions

The complex methods of the physicochemical analysis are used to study TlGaTe{sub 2}–Te and TlInTe{sub 2}–Te alloys in which the tellurium solubility region up to 5.0 at % is observed. The temperature dependences of the lattice parameters and the electrical conductivity of TlGaTe{sub 2+x} and TlInTe{sub 2+x} have been studied in different crystallographic directions. The TlGaTe{sub 2+x} and TlInTe{sub 2+x} solid solutions undergo a phase transition at a temperature of 498 K. The transition nature is interpreted.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2011

SULFATE SOLUBILITY LIMIT VERIFICATION FOR DWPF SLUDGE BATCH 7B

The objective of this study was to determine a sulfate solubility limit in glass for Sludge Batch 7b (SB7b). The SB7b composition projection provided by Savannah River Remediation (SRR) on May 25, 2011 was used as the basis for formulating glass compositions to determine the sulfate limit. Additions of Na{sub 2}O to the projected sludge composition were made by the Savannah River National Laboratory (SRNL) due to uncertainty in the final concentration of Na{sub 2}O for SB7b, which is dependent on washing effectiveness and the potential need to add NaOH to ensure an acceptable projected operating window. Additions of 4, 6, and 8 wt % Na{sub 2}O were made to the nominal May 25, 2011 composition projection. An updated SB7b composition projection was received from SRR on August 4, 2011. Due to compositional similarities, no additional experimental work using the August 4, 2011 compositions was considered to be necessary for this study. Both Frit 418 and Frit 702 were included in this study. The targeted sulfate (SO{sub 4}{sup 2-}) concentrations of the study glasses were selected within the range of 0.6 to 0.9 wt % in glass. A total of 52 glass compositions were selected based on the compositional variables of Na{sub 2}O addition, Actinide Removal Process (ARP) stream addition, waste loading, frit composition, and sulfate concentration. The glasses were batched, melted, and characterized following SRNL procedures. Visual observations were recorded for each glass after it cooled and used as in indicator of sulfur retention. Representative samples of each of the glasses fabricated were subjected to chemical analysis to determine whether the targeted compositions were met, as well as to determine the quantity of sulfate that was retained after melting. In general, the measured composition data showed that there were only minor issues in meeting the targeted compositions for the study glasses, and the measured sulfate concentrations for each study glass were within 10% of the targeted values. The results for the SB7b glasses fabricated with Frit 418 showed an apparent trend of increasing sulfate retention with increasing Na{sub 2}O additions to the 5/25/11 sludge projection. This trend appears contradictory to other recent studies of sulfate retention in Defense Waste Processing Facility (DWPF) type glasses. Additional apparent contradictions to this trend were found in the data collected in the present study. Overall, the results for the SB7b sulfate study glasses with Frit 418 and the 5/25/11 projection with Na{sub 2}O additions showed that subtle changes in this complex glass composition impacted the degree of sulfate retention. These results do however provide confidence that a 0.6 wt % sulfate limit in glass is warranted for Frit 418 with the SB7b compositions evaluated in this study. The results for the SB7b glasses fabricated with Frit 702 are consistent with those of the previous SB7a study in that Frit 702 allowed for higher sulfate retention as compared to Frit 418 for the same sludge compositions. It is recommended that the DWPF implement a sulfate concentration limit of 0.6 wt % in glass for SB7b processing with Frit 418. If a higher than projected sulfate concentration is measured when SB7b processing begins (i.e., if a sulfate concentration higher than 0.6 wt % becomes necessary to achieve targeted waste loadings), DWPF should consider a transition to Frit 702. The sulfate limit could likely be raised to 0.8 wt % by transitioning to this frit. However, if DWPF considers transitioning from Frit 418 to Frit 702, additional glasses should be fabricated to confirm this higher limit due to the issues with incorrect B{sub 2}O{sub 3} concentrations for some of the glasses made with Frit 702 in this study. There are several factors other than sulfate retention that must also be carefully considered prior to changing frit compositions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗