Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAINLESS STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Influence of Heat Input and Cold Wire Feeding Rate on Pitting Corrosion Resistance of Submerged Arc Welding Duplex Stainless Steel Welds

Welding thermal cycles may severely impair duplex stainless steel (DSS) performance, especially local pitting resistance and toughness. The restricted welding energy between 0.5 and 2.5 kJ mm{sup −1} represents a limiting factor for productivity increase in DSS welding, and the addition of cold wire is an interesting alternative to increase the welding deposition rate without adding extra heat. The aim of this work is to evaluate the influence of the cold wire feeding rate (CW) and heat input (HI) on pitting corrosion behavior of DSS UNS S32304 bead-on-plate welds obtained by submerged arc welding (SAW). Cyclic potentiodynamic polarization was carried out in transverse weld sections using 1 mol L{sup −1} NaCl solution at room temperature. Most pitting corrosion spots were located on the heat-affected zone (HAZ), and the pitting potentials were lower than the base metal due to higher ferrite fractions and the presence of chromium nitrides. Considering the same CW, the HI increasing reduced E{sub pit} for 1.6, 1.9, 2.2 kJ mm{sup −1}, but increased E{sub pit} for 2.7 kJ mm{sup −1}, due to a balance between the HAZ width and the austenite fraction.

36 MATERIALS SCIENCE↗

Effect of deposition rate on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by laser engineered net shaping

Laser engineered net shaping (LENS) is an additive manufacturing technique for fabricating and repairing metallic components. However, the relationships between its process parameters and the resulting mechanical properties of alloys such as 17-4 precipitation-hardening (PH) stainless steel require further investigation to enable reliable application. This study examines the specific effect of LENS deposition rate on the microstructure and mechanical properties of 17-4 PH stainless steel. Specimens were fabricated at two different deposition rates (8.47 and 9.31 mm s−1), subjected to subsequent solution and H900 aging treatment, and then evaluated via tensile testing, hardness measurements, and microscopy. A higher deposition rate results in a finer grain structure but increased porosity, leading to greater ultimate tensile strength (∼1294 MPa) yet lower ductility (strain at failure ∼5.8%) compared to the slower deposition rate (∼1266 MPa, ∼9.0% strain). Hardness follows the same trend as tensile strength. Tensile fracture surfaces for both conditions exhibited a mixed mode of ductile dimples and brittle quasi-cleavage regions, with chromium/silicon oxide particles identified within dimples. Complementary finite element modeling indicates that small void fractions primarily reduce ductility by enhancing localized plasticity, with only a marginal decrease in tensile strength. These integrated experimental and numerical results elucidate the mechanical properties linked to deposition rate, providing insight into tailoring LENS processes to achieve desired properties of 17-4 PH stainless steel.

17-4 PH stainlesssteel↗

Moessbauer spectroscopy study on the corrosion resistance of plasma nitrided ASTM F138 stainless steel in chloride solution

Plasma nitriding of ASTM F138 stainless steel samples has been carried out using dc glow discharge under 80% H{sub 2}-20% N{sub 2} gas mixture, at 673 K, and 2, 4, and 7 h time intervals, in order to investigate the influence of treatment time on the microstructure and the corrosion resistance properties. The samples were characterized by scanning electron microscopy, glancing angle X-ray diffraction and conversion electron Moessbauer spectroscopy, besides electrochemical tests in NaCl aerated solution. A modified layer of about 6 {mu}m was observed for all the nitrided samples, independent of nitriding time. The X-ray diffraction analysis shows broad {gamma}{sub N} phase peaks, signifying a great degree of nitrogen supersaturation. Besides {gamma}{sub N,} the Moessbauer spectroscopy results indicated the occurrence of {gamma}' and {epsilon} phases, as well as some other less important phases. Corrosion measurements demonstrate that the plasma nitriding time affects the corrosion resistance and the best performance is reached at 4 h treatment. It seems that the {epsilon}/{gamma}' fraction ratio plays an important role on the resistance corrosion. Additionally, the Moessbauer spectroscopy was decisive in this study, since it was able to identify and quantify the iron phases that influence the corrosion resistance of plasma nitrided ASTM F138 samples.

36 MATERIALS SCIENCE↗

Deformation band corrosion as a result of applied stress and cold-work in 304 stainless steel in simulated pressurized water reactor primary water conditions

Stainless steels like 304SS are commonly used in pressurized water reactor primary water environments due to their excellent resistance to stress corrosion cracking (SCC). However, SCC susceptibility has been observed in cold-worked 304SS. Cold-rolling introduces a high density of defects, such as deformation bands or dislocations, into the microstructure; applied stress, even if macroscopically below the yield stress, can result in regions with high localized stresses. Cold-worked and non-cold-worked samples were exposed to 360 °C simulated PWR primary water for 1500 h with and without active loading. Corrosion susceptibility of dislocations and deformation bands induced by cold-rolling and/or applied stress was studied using high-resolution (analytical) transmission electron microscopy. Deformation bands were generated in all specimens examined in the study. Penetrative oxidation was observed in some deformation bands in each specimen. The depth of penetrative deformation band oxidation frequently exceeded the depth of grain boundary oxidation in all specimens. However, deformation band oxides generally were narrowly confined to the deformation band plane. Highly Ni-rich regions were observed beyond all oxidation fronts. Surface oxides were thicker in the specimens exposed under active loading. In conclusion, the implications of these findings at surfaces for deformation bands intersecting stress corrosion crack paths are discussed.

EFTEM↗

Chemical interaction and compatibility of uranium mononitride and alumina forming austenitic stainless steel

Uranium mononitride (UN) and alumina forming austenitic (AFA) stainless steel are a potential fuel-cladding combination for the lead-cooled fast reactor (LFR). Chemical compatibility between UN and AFA steel needs to be verified before implementation in a nuclear reactor. Diffusion couple experiments at 823 K and 1023 K were conducted for nonirradiated UN samples in contact with as-cast (no thermally grown Al 2 O 3 ) and preoxidized (with thermally grown Al 2 O 3 ) AFA for 500 and 1000 h in an inert environment. Preoxidized AFA exhibited little to no interaction with all UN samples tested at both 823 K and 1023 K, displaying the stability and capability of the Al 2 O 3 layer to prevent chemical interaction and inter-diffusion with UN. Chemical interaction occurs between UN and as-cast AFA. At 1023 K, an aluminum and nitrogen rich phase (likely AlN) formed along the interface of as-cast AFA and UN samples. At 823 K the AlN phase was not prominently observed due to the reduced diffusivity of aluminum through AFA. The aluminum and nitrogen-enriched phase was also observed in a high temperature pressure-assisted test sample of UN and as-cast AFA thermally treated at 1373 K. Finally, in UN samples doped with a low weight percent of UO 2 (< 3 wt%), AlN was not detected along the interface at either temperatures, and an Al 2 O 3 layer likely formed along the interface and prevented further chemical interaction between UN and as-cast AFA.

36 MATERIALS SCIENCE↗

Weldability of irradiated Stainless Steel 304 materials harvested from the National Research Universal (NRU) reactor

In this work, the weldability of the neutron-irradiated Stainless Steel 304 (SS 304) materials containing estimated helium levels of 12 to 44 appm has been studied through a Collaborative Research and Development Agreement between the Canadian Nuclear Laboratories and Oak Ridge National Laboratory. The work utilizes a SS 304 component harvested from the National Research Universal reactor. Laser beam welding was used to explore suitable welding conditions and associated parameters, to determine helium concentration limits for successful welding of irradiated stainless-steels. The experimental results show that maximum fusion zone void sizes, fusion zone void quantity and total heat affected zone helium-induced crack length generally increased with increasing He levels and effective weld heat input. A proper combination of welding parameters with low effective heat input, such as, laser power, weld travel speed and wire feed speed, were shown to improve the welding quality, and potentially reduce the length and probability of the formation of grain boundary helium-induced cracking and voids of irradiated SS 304 even with He concentrations as high as about 44 appm.

36 MATERIALS SCIENCE↗

Nano/ultrafine grained austenitic stainless steel through the formation and reversion of deformation-induced martensite: Mechanisms, microstructures, mechanical properties, and TRIP effect

A comprehensive study was carried out on the strain-induced martensitic transformation, its reversion to austenite, the resultant grain refinement, and the enhancement of strength and strain-hardening ability through the transformation-induced plasticity (TRIP) effect in a commercial austenitic 304L stainless steel with emphasis on the mechanisms and the microstructural evolution. A straightforward magnetic measurement device, which is based on the measurement of the saturation magnetization, for evaluating the amount of strain-induced martensite after cold rolling and reversion annealing in metastable austenitic stainless steels was used, which its results were in good consistency with those of the X-ray diffraction (XRD) method. A new parameter called the effective reduction in thickness was introduced, which corresponds to the reasonable upper bound on the obtainable martensite fraction based on the saturation in the martensitic transformation. By means of thermodynamics calculations, the reversion mechanisms were estimated and subsequently validated by experimental results. The signs of thermal martensitic transformation at cooling stage after reversion at 850 °C were found, which was attributed to the rise in the martensite start temperature due to the carbide precipitation. After the reversion treatment, the average grain sizes were around 500 nm and the nanometric grains of the size of ~ 65 nm were also detected. The intense grain refinement led to the enhanced mechanical properties and observation of the change in the work-hardening capacity and TRIP effect behavior. A practical map as a guidance for grain refining and characterizing the stability against grain growth was proposed, which shows the limitation of the reversion mechanism for refinement of grain size. - Graphical abstract: Display Omitted - Highlights: • Nano/ultrafine grained austenitic stainless steel through martensite treatment • A parameter descriptive of a reasonable upper bound on the obtainable martensite • Characterization of martensite by virtue of a new developed magnetic device • Investigation of mechanical properties and TRIP effect and the effect of grain size.

36 MATERIALS SCIENCE↗

Surface Modification of 304 Stainless Steel by Electro-Spark Deposition

Electro-spark deposition (ESD) is a pulsed microwelding process that is used to apply surface coatings for the repair of damaged high value and precision products or modify their surfaces for specific properties. The low heat input, minimal heat-affected zone and the ability to form metallurgical bonding of coating to substrate are major advantages of the ESD process. Many applications require the components to have excellent surface performance, such as wear and corrosion resistance. ESD technique provides an approach to modify the component surface without compromising the bulk properties. In this study, surface modifications of 304 stainless steel by ESD were investigated. Titanium carbide (TiC), tungsten carbide (WC) and molybdenum (Mo) were employed as coating materials. Scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) analysis were conducted to characterize the microstructure and composition of the coatings. The coatings thicknesses were all around 40 µm. The results showed that TiC and WC coatings showed a dramatic increase in the microhardness, up to 5 times. WC coating improved the wear resistance by more than 5 times, while TiC and Mo coatings also improved it by approximately 2.5 times. Electro-chemical tests were conducted to investigate the corrosion resistance of the coatings. Mo coating exhibited a significant improvement in the corrosion resistance in 5% NaCl solutions, corroding 350 times slower than stainless steel. Synchrotron x-ray diffraction was performed to investigate the microstructure changes of the Mo-coated sample. Heat treatment was also carried out to investigate the corrosion behavior of Mo-coated 304 stainless steel at elevated service temperature in air or argon.

36 MATERIALS SCIENCE↗

FRACTURE MECHANICAL MEASUREMENTS WITH COMMERCIAL STAINLESS STEELS AT 4 K AND WITH CP-TITANIUM AT 173 K

Using the JETT (J-Evaluation on Tensile Test) technique, measurements have been performed with commercial stainless steels in forged and cast condition for the reason of an assessment for low temperature service down to 4 K. These steels frequently used for industrial applications are designated by German Werkstoff (WNr) 1.4308 and 1.4408 cast stainless steels and a forged material with the number 1.4307. The fracture toughness tests at 4 K with forged material 1.4307 comprised apart from the base metal also the weld zone and additionally the 5% and 8% pre-strained conditions of the base metal. Fracture toughness reduced slightly for cold worked condition gradually as well as for the weld joint. The Reliability of the JETT measurements has been also checked using the ASTM E 1820--99a standard. In addition, to these measurements, commercial pure ASTM grade 2 titanium (WNr 3.7035) has been also examined using the same JETT method for the reason of industrial application and the requirement of minimum fracture toughness of 100 MPasq root(m) was fulfilled at 173 K. Furthermore, test results performed at 7 K of pure titanium plate material (ASTM grade 1) with respect to fracture mechanical JETT method are presented.

36 MATERIALS SCIENCE↗

Effects of heat treatment and build orientation on the evolution of $ϵ$ and $α'$ martensite and strength during compressive loading of additively manufactured 304L stainless steel

In this paper, the effect of heat-treatment and build orientation on martensitic phase transformation in additively manufactured (AM) 304L stainless steel is studied and compared with conventionally produced wrought material. The relationships between observed martensitic transformations and material microstructures and their effects on mechanical strength are established through experimental observations. In situ high-energy X-ray powder diffraction measurements were performed to monitor the evolution of $ϵ$ and $α'$ martensite during compressive loading of stainless steel. Electron backscatter diffraction (EBSD) was used to provide insight on initial grain morphology, crystallographic misorientation within grains, and crystallographic texture. Heat treatment alters the microstructure of AM samples creating different initial conditions. This difference in starting microstructure resulted in variability in martensitic transformation during compressive deformation. The rate of martensitic transformation decreased for AM samples treated with temperatures up to 1100°C, after which the AM microstructures recrystallized, resulting in increased rate of martensitic transformation for those samples treated at higher temperatures. It was also observed that aligning the axis of compression with the AM build direction resulted in a lower rate of strain-induced martensite formation as opposed to aligning the compression axis perpendicular to it. More favorable distribution of crystal orientations in the latter loading orientation promoted martensitic transformation. These and additional experimental observations from EBSD in terms of kernel average misorientation, mean grain orientation spread, and mean crystallite size reveal strong microstructural effects on strength of additively manufactured metallic materials.

304L stainless steel↗

Measurement of the muon-induced neutron yield in liquid scintillator and stainless steel at LNGS with the LVD experiment

We describe the measurement of the muon-induced neutron yield in liquid scintillator and stainless steel (SS) at the Gran Sasso National Laboratory (LNGS), with the LVD experiment. The Large Volume Detector (LVD) is located in Hall A of the LNGS and is made of 1000 t of liquid scintillator and 1000 t of SS. Using an independent measurement to evaluate the background and with the support of a full Monte Carlo simulation based on Geant4, we measured a neutron yield of (2.9±0.6)×10{sup −4} and (1.5±0.3)×10{sup −3} in liquid scintillator and in stainless steel, respectively.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Predicting the creep-rupture lifetime of a cast austenitic stainless steel using Larson-Miller and Wilshire parametric approaches

An experimental dataset of just over 100 creep tests of a cast austenitic stainless steel, CF8C-Plus, was analyzed by two temperature-compensated parametric models (Larson-Miller, Wilshire et al.) to predict long-term lifetimes as functions of temperature and stress. The dataset and associated regression analyses showed greater scatter than typically found in recent similar studies of wrought Ni-based alloys by the same two models and was attributed to the microstructural inhomogeneity of the cast stainless steel. Qualitatively, the Larson-Miller formalism showed greater lifetime prediction accuracy than the Wilshire approach, with the latter model's predictive ability being particularly degraded by the presence of two very significant outlier results. This observation suggests that the Larson-Miller approach is more robust when treating rupture-time datasets that show particularly wide experimental scatter. Despite the differences in the overall predictive ability, both models yielded similar predictions of the applied stress at which CF8C-Plus would have a creep-limited lifetime of 100,000 h when loaded below the yield point.

36 MATERIALS SCIENCE↗

Characterization of Hydrophobic Silane Film Deposited on AISI 304 Stainless Steel for Corrosion Protection

This present study was conducted to determine the aptitude of hydrophobic silane coating in corrosion resistance of AISI 304 stainless steel substrate at the nanoscale. Three newly developed hydrophobic silane-based compounds of compositions, namely [tris(trimethylsiloxy)silyethyl]dimethylchlorosilane (alkyl); tridecafloro-1,1,2,2-tetrahydrooctyltrichlorosilane (FOTS); and henicosyl-1,1,2,2-tetrahydrododecyltricholrosilane (FDDTS), were used as precursors to coat AISI 304 stainless steel surfaces. Prior to deposition, the substrate surfaces were pretreated with plasma oxide via a multi-step treatment to serve as adhesion. The plasma oxide and the silane precursors were deposited by using a hybrid atomic layer deposition and chemical vapor deposition process. The structural, chemical and electrochemical stabilities were investigated using SEM, AFM, XRD, ATR-FTIR, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The results showed that the microstructures and morphology of the coated samples were similar, due to the chlorosilane functionalization. The FTIR indicated complete hydrolysis at the nanoscale while the polarization results showed that nano-coating can hamper the corrosion propagation mechanisms. Furthermore, the EIS results revealed that all the precursors acted as a barrier to AISI 304 dissolution into the electrolyte. The electrochemical effect was observed in the microstructural transformation of the coatings. Although all the precursors were shown to have been effective at few nanoscales, the stability of the FDDTS showed to have superseded that of alkyl and FOTS.

36 MATERIALS SCIENCE↗

Rotary Inertia Friction Welding of Dissimilar High-Strength 422 Martensitic Stainless Steel and 4140 Low Alloy Steel for Heavy-Duty Engine Piston Fabrication

AISI 422 martensitic stainless steel with superior high temperature performance (oxidation resistance and strength) is under evaluation for replacing current heavy-duty piston crown materials, AISI 4140 martensitic steel and micro alloyed steel (MAS) 38MnSiVS5, to fabricate a multimaterial piston. This multimaterial piston concept further improved power density and fuel economy by allowing heavyduty diesel engines to operate at higher temperatures and pressures. Joining AISI 422 steel piston crowns with AISI 4140 steel piston skirts is a key manufacturing step for this multimaterial piston. However, the significant differences in strength, elevated temperature flow stress, alloy chemistry, and temper resistance between these two martensitic steels cause some weldability issues (cracking) and metallurgical challenges (alloying element migration/segregation) when using conventional fusion-based welding processes. Rotary inertia friction welding (RIFW), a solid-state welding process, has been the preferred method to join 4140 crowns to 4140 skirts (and MAS crowns to MAS skirts) in high-volume production of current heavy-duty diesel engine pistons. It has been used to join these two materials with relatively comparable alloy chemistry to fabricate pistons with MAS skirts and 4140 crowns. Meanwhile, RIFW has also been a preferred method of dissimilar metal welding. However, RIFW of dissimilar high-strength martensitic steels has yet to be widely pursued. The interfacial microstructure complexities created by the thermomechanical process and highly nonequilibrium phase transformations during RIFW are a significant challenge for understanding and predicting their joining behavior and have not been reported in detail. Here, in this work, defect-free AISI 422 steel-AISI 4140 multimaterial pistons were successfully fabricated using the RIFW process. The interfacial microstructure and mechanical properties of dissimilar 422/4140 steel RIFW in the as-welded condition were experimentally studied in detail. The results provide critical baseline information for understanding RIFW mechanisms and guiding subsequent postweld heat treatment (PWHT) practice.

36 MATERIALS SCIENCE↗

Composition-dependence of 316 austenitic stainless steel deformation and aging properties for high-temperature applications - 18696

The present article is part of a broader effort aimed at assessing the possibility of tailoring the plasticity of austenitic stainless steels for structural applications in nuclear reactors. Three annealed heats of 316 stainless steel with large differences in stacking fault energy, carbon content, and ferrite content were used to study deformation and aging behaviors. Deformation of samples was investigated at room temperature by conventional tensile testing and at 350 deg. C by in situ neutron diffraction tensile testing. Aging was studied after 15 h at 750 deg. C through X ray diffraction and nano-indentation. (authors)

36 MATERIALS SCIENCE↗

Second group of irradiation capsules: property data of irradiated welded stainless steel 347 and irradiated, welded, and hydrogen charged Zircaloy-4 for SHINE

Zircaloy-4 and AISI 347 stainless steel were irradiated to low doses (10 20 and 10 21 n/cm 2 ) at low temperature (~60°C) in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). These materials were under consideration for some of the structural components of the medical isotope production facility developed by SHINE Technologies. Zircaloy-4 base metal, as welded, welded and post-weld heat treated (PWHT), and hydrogen charged samples were irradiated. AISI 347 base metal from Sandmeyer Steel, Penn Stainless, and Rolled Alloys suppliers were irradiated. AISI 347 gas tungsten arc welding (GTAW) and flux-cored arc welding (FCAW) samples of Penn Stainless and Rolled Alloys were also irradiated. The irradiated materials were tested with microhardness and tensile tests at room temperature in air. The AISI 347 materials had more elongation after irradiation than the Zircaloy-4 materials. In fact, the Zircaloy-4 welded without PWHT and with H charging had the lowest elongation of any of the materials. This report is the final in a series of reports on this project.

36 MATERIALS SCIENCE↗