SEARCH · Engineering Papers

Results for “STAGNATION PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

NASA NTRS1988

An isentropic compression heated Ludwieg tube transient wind tunnel

Syracuse University's Ludwieg tube with isentropic compression facility is a transient wind tunnel employing a piston drive that incorporates insentropic compression heating of the test gas located ahead of a piston. The facility is well-suited for experimental investigations concerning supersonic and subsonic vehicles over a wide range of pressures, Reynolds numbers, and temperatures; all three parameters can be almost independently controlled. Work at the facility currently includes wake-induced stagnation point heat transfer and supersonic boundary layer transition.

Magari, Patrick J.↗

NASA NTRS1990

3D computation of hypersonic nozzle

Numerical results of a NASP-like nozzle configuration are presented. The nozzle has characteristically a very large area ratio designed to operate in the hypersonic regime. The overall flowfield consists of the internal expansion from a stagnation reservoir and the external exhaust plume in a quiescent environment. The solutions were obtained for two experimental conditions at an underexpanded pressure ratio of 44000 and an overexpanded pressure ratio of 2495. These conditions produce flows expanding to high Mach numbers in the hypersonic range. At the nozzle entrance, the flow has a supersonic Mach number of 4.3 in the inviscid region. In the external expansion and exhaust regions, the flow expands to a maximum Mach number of 12.3 for the case of high pressure ratio, whereas a shock wave exists for the low pressure ratio case. The solutions from these three-dimensional calculations were compared to the experimental data for pressure distributions.

Lai, H. T.↗

NASA NTRS1979

Some aspects of a free jet phenomena to 105 L/D in a constant area duct

Under certain conditions, inlets with a Borda type geometry were shown to exhibit sufficiently strong separation effects to permit the working fluid to flow through the duct as if it were a free jet. Mass limiting flow data and associated pressure profiles for tubes of 14, 53, 64, 73, and 105 L/D with a Borda type inlet were taken to determine bounds of the free jet phenomena. For a given tube roughness, the limits appear to be one dimensional and dependent only on inlet stagnation conditions. For smooth tubes the upper L/D boundary is related by P sub R roughly equal to CT to the 17th power and sub R, C roughly equal to 00017 (L/D) to the 2.5 power where F sub R = P/P sub c is reduced pressure and T sub R = T/T sub c is reduced temperature. The lower bound appears to be saturation conditions at the inlet. Similar free jet effects were found for fluid hydrogen indicating that fluid jetting may be common to all fluids. While limited data on surface roughness show a decrease in the upper L/D limit, nevertheless fluid jetting still occurred.

Hendricks, R. C.↗

NASA NTRS1957

Investigation of the Laminar Aerodynamic Heat-transfer Characteristics of a Hemisphere-cylinder in the Langley 11-inch Hypersonic Tunnel at a Mach Number of 6.8

A program to investigate the aerodynamic heat transfer of a nonisothermal hemisphere-cylinder has been conducted in the Langley 11-inch hypersonic tunnel at a Mach number of 6.8 and a Reynolds number from approximately 0.14 x 10(6) to 1.06 x 10(6) based on diameter and free-stream conditions. The experimental heat-transfer coefficients were slightly less over the whole body than those predicted by the theory of Stine and Wanlass (NACA technical note 3344) for an isothermal surface. For stations within 45 degrees of the stagnation point the heat-transfer coefficients could be correlated by a single relation between local Stanton number and local Reynolds number. Pitot pressure profiles taken at a Mach number of 6.8 on a hemisphere-cylinder have verified that the local Mach number or velocity outside the boundary layer required in the theories may be computed from the surface pressures by using isentropic flow relations and conditions immediately behind a normal shock. The experimental pressure distribution at Mach number of 6.8 is closely predicted by the modified Newtonian theory.

Crawford, Davis H↗

NASA NTRS1958

Experimental Behavior of Pentaborane-Air Combustion Products During Expansion in a Convergent Divergent Nozzle

In order to evaluate the post combustion behavior of boric oxide, pentaborane-air mixtures, burned to completion at a combustor pressure of 3 atmospheres, were expanded through a 7.1-inch-long convergent-divergent nozzle having a 4-inch-diameter throat and an exit-to-throat area ratio of 1.68. The experimentally determined thrust performance was in good agreement with the ideal equilibrium performance at stagnation temperatures of 3300 deg R and lower. The boric oxide vapor at the combustor exit required about 400 F deg supercooling before any condensed phase was observed. For a given thrust, fuel consumption was as much as 20 percent greater than predicted from vapor-pressure data for combustor outlet temperatures i n the vicinity of 3600 deg R. A similar result could be expected in full-scale engines, since the test combustor provided an unusually long dwell time and a highly turbulent environment. During the expansion process, the vapor (when present) did not condense to the extent predicted for an equilibrium expansion process. Moreover, condensation was observed only i n the form of small, abrupt phase changes i n the subsonic flow near the throat. Friction, due to liquid boric oxide films on the nozzle surfaces, was negligible when the surface temperature was above 800 F.

PENTABORANE↗

NASA NTRS1973

A new technique for calculating reentry base heating

The laminar base flow field of a two-dimensional reentry body has been studied by Telenin's method. The flow domain was divided into strips along the x-axis, and the flow variations were represented by Lagrange interpolation polynomials in the transformed vertical coordinate. The complete Navier-Stokes equations were used in the near wake region, and the boundary layer equations were applied elsewhere. The boundary conditions consisted of the flat plate thermal boundary layer in the forebody region and the near wake profile in the downstream region. The resulting two-point boundary value problem of 33 ordinary differential equations was then solved by the multiple shooting method. The detailed flow field and thermal environment in the base region are presented in the form of temperature contours, Mach number contours, velocity vectors, pressure distributions, and heat transfer coefficients on the base surface. The maximum heating rate was found on the centerline, and the two-dimensional stagnation point flow solution was adquate to estimate the maximum heating rate so long as the local Reynolds number could be obtained.

Meng, J. C. S.↗

NASA NTRS1977

Numerical solutions of Navier-Stokes equations for the structure of a trailing vortex

The structure and decay of a trailing vortex were analyzed during the numerical solutions of the full Navier-Stokes equations. Unsteady forms of the governing equations were recast in terms of circulation, vorticity, and stream function as dependent variables, and a second upwind finite difference scheme was used to integrate them with prescribed initial and boundary conditions. The boundary conditions at the outer edge and at the outflow section of the trailing vortex were considered. Different models of the flow were postulated, and solutions were obtained describing the development of the flow as integration proceeds in time. A parametric study was undertaken with a view to understanding the various phenomena that may possibly occur in the trailing vortex. Using the Hoffman and Joubert law of circulation at the inflow section, the results of this investigation were compared with experimental data for a Convair 990 wind model and a rectangular wing. With an exponentially decaying law of circulation at the inflow section and an adverse pressure gradient at the outer edge of the trailing vortex, solutions depict vortex bursting through the sudden expansion of the core and/or through the stagnation and consequent reversal of the flow on the axis. It was found that this bursting takes place at lower values of the swirl ratio as the Reynolds number increases.

Jain, A. C.↗

NASA NTRS1991

Transonic Navier-Stokes solutions about a generic hypersonic configuration

Three-dimensional transonic viscous flow computations are presented for a generic high-speed accelerator model that includes wing, body, fillets, and a no-flow-through engine nacelle. Solutions are obtained from an algorithm for the compressible Navier-Stokes equations that incorporates an upwind-biased, flux-vector-splitting approach along with longitudinally patched grids. Results are presented for fully turbulent flow assumptions and include correlations with wind-tunnel data. A good quantitative agreement for the forebody surface pressure distribution is achieved between computations and the available wind-tunnel measurements at M∞ = 0.9. Furthermore, it is demonstrated that the flow is stagnating around the boattail region due to separation from the aft-engine cowl lip.

Hypersonic flows↗

NASA NTRS2001

Aerothermodynamic Environment Definition for the Genesis Sample Return Capsule

NASA's Genesis sample return mission will be the first to return material from beyond the Earth-Moon system. NASA Langley Research Center supported this mission with aerothermodynamic analyses of the sample return capsule. This paper provides an overview of that effort. The capsule is attached through its forebody to the spacecraft bus. When the attachment is severed prior to Earth entry, forebody cavities remain. The presence of these cavities could dramatically increase the heating environment in their vicinity and downstream. A combination of computational fluid dynamics calculations and wind tunnel phosphor thermography tests were employed to address this issue. These results quantify the heating environment in and around the cavities, and were a factor in the decision to switch forebody heat shield materials. A transition map is developed which predicts that the flow aft of the penetrations will still be laminar at the peak heating point of the trajectory. As the vehicle continues along the trajectory to the peak dynamic pressure point, fully turbulent flow aft of the penetrations could occur. The integrated heat load calculations show that a heat shield sized to the stagnation point levels will be adequate for the predicted environment aft of the penetrations.

Cheatwood, F. McNeil↗

NASA NTRS2004

Real-Time Unsteady Loads Measurements Using Hot-Film Sensors

Several flight-critical aerodynamic problems such as buffet, flutter, stall, and wing rock are strongly affected or caused by abrupt changes in unsteady aerodynamic loads and moments. Advanced sensing and flow diagnostic techniques have made possible simultaneous identification and tracking, in real-time, of the critical surface, viscosity-related aerodynamic phenomena under both steady and unsteady flight conditions. The wind tunnel study reported here correlates surface hot-film measurements of leading edge stagnation point and separation point, with unsteady aerodynamic loads on a NACA 0015 airfoil. Lift predicted from the correlation model matches lift obtained from pressure sensors for an airfoil undergoing harmonic pitchup and pitchdown motions. An analytical model was developed that demonstrates expected stall trends for pitchup and pitchdown motions. This report demonstrates an ability to obtain unsteady aerodynamic loads in real-time, which could lead to advances in air vehicle safety, performance, ride-quality, control, and health management.

Mangalam, Arun S.↗

NASA NTRS2004

Real-Time Unsteady Loads Measurements Using Hot-Film Sensors

Several flight-critical aerodynamic problems such as buffet, flutter, stall, and wing rock are strongly affected or caused by abrupt changes in unsteady aerodynamic loads and moments. Advanced sensing and flow diagnostic techniques have made possible simultaneous identification and tracking, in realtime, of the critical surface, viscosity-related aerodynamic phenomena under both steady and unsteady flight conditions. The wind tunnel study reported here correlates surface hot-film measurements of leading edge stagnation point and separation point, with unsteady aerodynamic loads on a NACA 0015 airfoil. Lift predicted from the correlation model matches lift obtained from pressure sensors for an airfoil undergoing harmonic pitchup and pitchdown motions. An analytical model was developed that demonstrates expected stall trends for pitchup and pitchdown motions. This report demonstrates an ability to obtain unsteady aerodynamic loads in real time, which could lead to advances in air vehicle safety, performance, ride-quality, control, and health management.

Mangalam, Arun S.↗

NASA NTRS2012

Measurement of Vibrational Non-Equilibrium in a Supersonic Freestream Using Dual-Pump CARS

Measurements have been conducted at the University of Virginia Supersonic Combustion Facility of the flow in a constant area duct downstream of a Mach 2 nozzle, where the airflow has first been heated to approximately 1200 K. Dual-pump CARS was used to acquire rotational and vibrational temperatures of N2 and O2 at two planes in the duct at different downstream distances from the nozzle exit. Wall static pressures in the nozzle are also reported. With a flow of clean air, the vibrational temperature of N2 freezes at close to the heater stagnation temperature, while the O2 vibrational temperature is about 1000 K. The results are well predicted by computational fluid mechanics models employing separate "lumped" vibrational and translational/rotational temperatures. Experimental results are also reported for a few percent steam addition to the air and the effect of the steam is to bring the flow to thermal equilibrium.

Cutler, Andrew D.↗

NASA NTRS1956

Testing with the Laser-Enhanced Arc Jet Facility (LEAF) at NASA Ames Research Center

NASA's new Laser-Enhanced Arcjet Facility (LEAF) employs 200 kilowatts of continuous-wave fiber lasers, combined with a 60-megawatt arc plasma jet, to simulate the combined radiative and convective heating is now operational and Orion heat-shield material is undergoing testing. This upgrade to the existing Interaction Heating Facility (IHF) involves the addition of high-power fiber lasers that project 1070nm radiative energy into the existing vacuum chamber. The optically expanded laser beam enters a side window of the test chamber to form either a uniform 150 x 150 mm or a 425 x 425 mm square spot on a wedge-shaped model holder. Combined heating levels of up to 180 W/cm2 convective with either 300 W/cm2 or 100 W/cm2 are achievable. This allows the arc jet and lasers to simulate dynamic entry-heating profiles encountered during entry by the Orion crew capsule for the lunar return conditions. New computational investigations are underway to explore testing with the objective of defining ablative material failure limit. Typical arc-jet testing is performed with test article that are stagnation or wedge geometries. The existing convective heating test facility combined with test article design limits how high a combined shear, heat-flux and pressure conditions can be achieved. With the addition of laser power of 200 kW, much higher combined conditions of high heat-flux, pressure and shear is achievable on a wedge or a swept-cylinder article. Such testing possibilities will allow us to progressively increase the combined conditions and explore when an ablative TPS material may fail. The presentation provides an overview of the LEAF and present results from the on-going Orion Testing.

Venkatapathy, Ethiraj↗

NASA NTRSDate not supplied

Flow Visualization for Plume-Surface Interaction at Martian-Relevant Lander Environments

This paper describes a jet impingement experiment performed in a large-scale vacuum chamber at Martian-relevant ambient pressure conditions, with the motivation of studying plume-surface interaction (PSI) caused by the exhaust plume of a lander interacting with the planetary surface. Flow visualization of an inert supersonic jet was performed using planar laser-induced fluorescence (PLIF), which is a molecular-based, two-dimensional measurement technique. Representative instantaneous and time-averaged visualizations of the impinging jet at two different nozzle flow conditions corresponding to the underexpanded and overexpanded jet regimes are presented for up to six different dimensionless altitudes h/De. The time-averaged measured spatial distribution of impingement pressures at these conditions is also reported. The PLIF visualizations appear to be critical towards explaining unexpected behavior in the impingement pressure, such as a higher impingement pressure for the underexpanded condition at h/De = 10, compared to a lower altitude of h/De = 8. This behavior can be attributed to differences in the stagnation shock structure observed in the PLIF images. The PLIF images also reveal significant flow separation at the nozzle exit for the overexpanded jet conditions. Further analysis of the test data as well as combined flow visualization and surface diagnostics for future ground tests will help inform engineering designs for landings on the Martian surface while mitigating PSI risks.

PLIF↗

NASA NTRSDate not supplied

Flow Visualization for Plume-Surface Interaction at Martian-Relevant Lander Environments

PLIF↗

NASA NTRS1954

Experimental Investigation of Effects of Primary Jet Flow and Secondary Flow Through a Zero-length Ejector on Base and Boattail Pressures of a Body of Revolution at Free-stream Mach Numbers of 1.62, 1.93, and 2.41

An investigation was made at free-stream Mach numbers of 1.62, 1.93, and 2.41 to determine the effects of a primary jet and secondary air flow on the base pressure and pressures acting over the boattailsurface of a body of revolution for two secondary discharge areas. The Mach numbers of the primary nozzles were 1 and 3.23 with the secondary mass flow being varied from 0 to 10 percent of the primary mass flow. The ratio of jet stagnation temperature to tunnel stagnation temperature was about 0.96. The Reynolds number range of the investigation was from 2.1 x 10(6) to 2.9 x 10(6)based on body length. All testing was conducted with a turbulent boundary layer along the model. This report presents results obtained with zero-length ejector and covers jet static-pressure ratios from the jet-off condition to a maximum of about 128 for the sonic nozzle and to a maximum of about 9 for the supersonic nozzle.

O'Donnell, Robert M↗

NASA NTRS1988

A computational study of heat transfer for laminar hypervelocity flows

Computational Fluid Dynamics (CFD) codes are routinely used to predict the flowfield and the heating environment around complex reentry configurations. At hypervelocities, where the velocity is greater than 3 km/sec, the AFWAL version of the blunt body code predicts the correct surface pressure distributions but underpredicts laminar wall heat fluxes. This study was performed to determine the reasons for the underprediction. The computer code chosen solves thin-layer Navier-Stokes equations in a time-asymptotic manner and assumes a constant isentropic exponent. Flowfields around a spherical configuration at various entry velocities are computed. The computed pressure distributions agree well with the tabulated, inviscid results of Lyubimov and Rusanov for entry velocities ranging from 0.6 to 5.92 km/sec. At hypervelocities, the calculated stagnation point heat transfer rates were lower by roughly fifty percent when compared to engineering correlations available in the literature. Good comparisons between heat transfer rates are obtained at hypervelocity entry conditions provided the CFD code is modified to include equilibrium air properties.

Balakrishnan, A.↗