Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SEEBECK EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2013

High figure of merit and thermoelectric properties of Bi-doped Mg{sub 2}Si{sub 0.4}Sn{sub 0.6} solid solutions

The study of Mg{sub 2}Si{sub 1−x}Sn{sub x}-based thermoelectric materials has received widespread attention due to a potentially high thermoelectric performance, abundant raw materials, relatively low cost of modules, and non-toxic character of compounds. In this research, Mg{sub 2.16}(Si{sub 0.4}Sn{sub 0.6}){sub 1−y}Bi{sub y} solid solutions with the nominal Bi content of 0≤y≤0.03 are prepared using a two-step solid state reaction followed by spark plasma sintering consolidation. Within this range of Bi concentrations, no evidence of second phase segregation was found. Bi is confirmed to occupy the Si/Sn sites in the crystal lattice and behaves as an efficient n-type dopant in Mg{sub 2}Si{sub 0.4}Sn{sub 0.6}. Similar to the effect of Sb, Bi doping greatly increases the electron density and the power factor, and reduces the lattice thermal conductivity of Mg{sub 2.16}Si{sub 0.4}Sn{sub 0.6} solid solutions. Overall, the thermoelectric figure of merit of Bi-doped Mg{sub 2.16}Si{sub 0.4}Sn{sub 0.6} solid solutions is improved by about 10% in comparison to values obtained with Sb-doped materials of comparable dopant content. This improvement comes chiefly from a marginally higher Seebeck coefficient of Bi-doped solid solutions. The highest ZT∼1.4 is achieved for the y=0.03 composition at 800 K. - Graphical abstract: (a)The relationship between electrical conductivity and power factor for Sb/Bi-doped Mg{sub 2.16}(Si{sub 0.4}Sn{sub 0.6}){sub 1−y}(Sb/Bi){sub y} (0<y≤0.03) solid solutions. (b)The correlation between temperature and the combination of the lattice and the bipolar terms of thermal conductivity of Mg{sub 2.16}(Si{sub 0.4}Sn{sub 0.6}){sub 1−y}Bi{sub y} (0≤y≤0.03) solid solutions. (c)Temperature dependent dimensionless figure of merit ZT of Mg{sub 2.16}(Si{sub 0.4}Sn{sub 0.6}){sub 1−y}Bi{sub y} (0≤y≤0.03) solid solutions. - Highlights: • Bi doped Mg{sub 2.16}Si{sub 0.4}Sn{sub 0.6} showed 15% enhancement in the power factor as compared to Sb doped samples. • Bi doping reduced κ{sub ph} of Mg{sub 2.16}Si{sub 0.4}Sn{sub 0.6} due to stronger point defect scattering. • The highest ZT=1.4 at 800 K was achieved for Mg{sub 2.16}(Si{sub 0.4}Sn{sub 0.6}){sub 0.97}Bi{sub 0.03}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2013

Improved Thermoelectric Performance of p-type Skutterudite YbxFe4-yPtySb12 (0.8 x 1, y = 1 and 0.5)

Thermoelectric performance of p-type skutterudites currently lags that of the corresponding n-type materials and improvement of this important class of materials have become the focus of considerable research effort world-wide. Recent calculations find promising band structural features in p-type skutterudite materials of the type AeFe3NiSb12 ( Ae = Ca, Sr, or Ba) which could potentially lead to excellent thermoelectric properties. Recent work on the Yb- filled analog of the these formulations (YbFe3NiSb12) however finds that the onset of intrinsic conduction at lower than expected temperatures deteriorates the performance above 500 K leading to poor performance in the temperature range of interest for automotive waste heat recovery applications. We therefore seek a way to increase the band gap in order to find a way to minimize the deleterious effects of intrinsic conduction. Here we present ab initio band structure calculations and the synthesis and thermoelectric properties of YbxFe4-yPtySb12 (0.8 x 1, y = 1 and 0.5). Ab initio calculations find that the band gap increases for YbFe3PtSb12 as compared to the Ni-containing analog, though no such increase in the band gap energy was found for as compared to YbFe3.5Ni0.5Sb12. The y = 1 samples shows a characteristic transition to intrinsic conduction with a decrease in the Seebeck coefficient at temperatures above 700 K. The increased carrier concentration in y = 0.5 virtually eliminates any evidence of intrinsic conduction and the Seebeck coefficients for these samples increase monotonically up to 750 K, resulting in power factors approaching 27 W/cm K2 at 750 K. These power factors combined with low thermal conductivity result in a ZT = 0.9 at 750 K for Yb0.95Fe3.5Pt0.5Sb12.

skutterudite↗
DOE OSTI2025

Large language model-driven database for thermoelectric materials

Thermoelectric materials have the ability to convert waste heat into electricity, offering a valuable solution for energy harvesting. However, their widespread use is hindered by low conversion efficiency, the reliance on expensive rare earth elements, and the environmental and regulatory concerns associated with lead-based materials. A fast and cost-effective way to identify highly efficient thermoelectric materials is through data-driven methods. These approaches rely on robust and comprehensive datasets to train models. Although there are several databases on thermoelectric materials, there is still a need to collect and integrate experimental data from peer-reviewed research articles to capture diverse compositions and properties of materials. Here, in this work, we developed a comprehensive database of 7,123 thermoelectric compounds, containing key information such as chemical composition, structural detail, seebeck coefficient, electrical and thermal conductivity, power factor, and figure of merit (ZT). We used the GPTArticleExtractor workflow, powered by large language models (LLM), to extract and curate data automatically from the scientific literature published in Elsevier journals. This process enabled the creation of a structured database that addresses the challenges of manual data collection. The open access database could stimulate data-driven research and advance thermoelectric material analysis and discovery.

Database↗
DOE OSTI2015

Parametric modeling of energy filtering by energy barriers in thermoelectric nanocomposites

We present a parametric modeling of the thermoelectric transport coefficients based on a model previously used to interpret experimental measurements on the conductivity, σ, and Seebeck coefficient, S, in highly Boron-doped polycrystalline Si, where a very significant thermoelectric power factor (TPF) enhancement was observed. We have derived analytical formalism for the transport coefficients in the presence of an energy barrier assuming thermionic emission over the barrier for (i) non-degenerate and (ii) degenerate one-band semiconductor. Simple generic parametric equations are found that are in agreement with the exact Boltzmann transport formalism in a wide range of parameters. Moreover, we explore the effect of energy barriers in 1-d composite semiconductors in the presence of two phases: (a) the bulk-like phase and (b) the barrier phase. It is pointed out that significant TPF enhancement can be achieved in the composite structure of two phases with different thermal conductivities. The TPF enhancement is estimated as a function of temperature, the Fermi energy position, the type of scattering, and the barrier height. The derived modeling provides guidance for experiments and device design.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Intrinsic Berry curvature driven anomalous Nernst thermopower in the semimetallic Heusler alloy CoFeVSb

Understanding of spin-heat coupling mechanisms and magnetothermoelectric phenomena, including the anomalous Nernst effect (ANE), in emergent quaternary Heusler alloys is of practical importance for applications in thermal management and energy harvesting. Here, we demonstrate an intrinsic Berry curvature mediated anomalous Nernst thermopower in CoFeVSb, which orders magnetically at high temperature ( T C ≈ 850 K ) with a large saturation magnetization of ≈ 2.2 μ B / f . u . at room temperature. We show that the electron-electron elastic and electron-magnon inelastic scattering dominate longitudinal electrical transport at low temperatures ( T ≤ 50 K ), whereas the electron-phonon and electron-magnon scatterings govern it at higher T . The longitudinal thermopower is resulted mainly from the diffusive contribution with a very large longitudinal Seebeck coefficient ( 42 μ V K - 1 at 395 K). The value of the anomalous Nernst coefficient ( S ANE ) for CoFeVSb at room temperature is 0.039 μ V K - 1 which is higher than the compressively strained SrRu O 3 film ( 0.03 μ V K - 1 ) as well as the spin gapless semiconductor CoFeCrGa ( 0.018 μ V K - 1 ). On lowering T , both the ordinary Nernst coefficient and carrier mobility increase but an opposite trend is found for S ANE . Our ab initio simulations reveal the topological semimetallic nature of CoFeVSb with a pair of Weyl points. These Weyl crossings result in a significant contribution to the Berry curvature, leading to an intrinsic anomalous Hall conductivity ( σ x y AHE ) of ≈ 85 S/cm, which matches well with experiment (77 S/cm at 2 K). Our experimental findings and ab initio calculations support the dominance of the intrinsic Berry curvature in the observed ANE. The ratio of σ x y AHE to the transverse anomalous thermoelectric conductivity ( α x y ANE ) shows an increasing trend with T attaining a sizable fraction of k B e ( ≈ 0.35 k B e ) at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Activation energy of metastable amorphous Ge 2 Sb 2 Te 5 from room temperature to melt

Resistivity of metastable amorphous Ge 2 Sb 2 Te 5 (GST) measured at device level show an exponential decline with temperature matching with the steady-state thin-film resistivity measured at 858 K (melting temperature). This suggests that the free carrier activation mechanisms form a continuum in a large temperature scale (300 K – 858 K) and the metastable amorphous phase can be treated as a super-cooled liquid. The effective activation energy calculated using the resistivity versus temperature data follow a parabolic behavior, with a room temperature value of 333 meV, peaking to ~377 meV at ~465 K and reaching zero at ~930 K, using a reference activation energy of 111 meV (3kBT/2) at melt. Amorphous GST is expected to behave as a p-type semiconductor at T melt ~ 858 K and transitions from the semiconducting-liquid phase to the metallic-liquid phase at ~930 K at equilibrium. The simultaneous Seebeck (S) and resistivity versus temperature measurements of amorphous-fcc mixed-phase GST thin-films show linear S-T trends that meet S = 0 at 0 K, consistent with degenerate semiconductors, and the dS/dT and room temperature activation energy show a linear correlation. The single-crystal fcc is calculated to have dS/dT = 0.153 μ V/K 2 for an activation energy of zero and a Fermi level 0.16 eV below the valance band edge.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A robust high sensitivity scanning thermal probe for simultaneous microscale thermal and thermoelectric property mapping

Scanning Thermal Microscopy (SThM) provides efficient thermal property measurement with micro- or nanoscale spatial resolution. However, the sensitivity and accuracy of state-of-the-art thermal probes have been limited by excessive thermal contact resistance between the probe and sample. Introduced herein is a robust thermal microprobe that can increase the probe-sample contact force by more than two orders of magnitude, thereby reducing the probe-sample thermal contact resistance by as much as 96% and increasing measurement sensitivity by more than 240% compared to a commercial thermal probe with the same dimensions and measurement principle. The relationship between the probe-sample thermal contact resistance, thermal exchange radius, and sample thermal conductivity is determined experimentally. Simultaneous measurement of thermal conductivity and Seebeck coefficient with unprecedented sensitivity is demonstrated using the enhanced scanning thermal microprobe on samples of an extended range of thermal conductivity up to 18 W/m K, increasing the range of samples applicable to SThM when compared to the conventional commercial probe with diminished measurement sensitivity above ~10 W/m K. The probe is further demonstrated by simultaneously mapping thermal conductivity and Seebeck coefficient as a function of depth from the irradiated surface of an ion-irradiated bulk nanostructured thermoelectric material. In addition to enabling microscale thermal conductivity and Seebeck coefficient measurement of materials previously not applicable to SThM, the probe can also facilitate high-throughput characterization of combinatorial materials to aid the rapid discovery of compositions and processing conditions that yield highly desired thermal and thermoelectric properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

When band convergence is not beneficial for thermoelectrics

Abstract Band convergence is considered a clear benefit to thermoelectric performance because it increases the charge carrier concentration for a given Fermi level, which typically enhances charge conductivity while preserving the Seebeck coefficient. However, this advantage hinges on the assumption that interband scattering of carriers is weak or insignificant. With first-principles treatment of electron-phonon scattering in the CaMg 2 Sb 2 -CaZn 2 Sb 2 Zintl system and full Heusler Sr 2 SbAu, we demonstrate that the benefit of band convergence can be intrinsically negated by interband scattering depending on the manner in which bands converge. In the Zintl alloy, band convergence does not improve weighted mobility or the density-of-states effective mass. We trace the underlying reason to the fact that the bands converge at a one k-point, which induces strong interband scattering of both the deformation-potential and the polar-optical kinds. The case contrasts with band convergence at distant k-points (as in the full Heusler), which better preserves the single-band scattering behavior thereby successfully leading to improved performance. Therefore, we suggest that band convergence as thermoelectric design principle is best suited to cases in which it occurs at distant k-points.

42 ENGINEERING↗
DOE OSTI2018

Isotropic Seebeck coefficient of aligned single-wall carbon nanotube films

How the morphology of a macroscopic assembly of nanoobjects affects its properties is a long-standing question in nanomaterials science and engineering. Here, we examine how the thermoelectric properties of a flexible thin film of carbon nanotubes depend on macroscopic nanotube alignment. Specifically, we have investigated the anisotropy of the Seebeck coefficient of aligned and gated single-wall carbon nanotube thin films. We varied the Fermi level in a wide range, covering both the p-type and n-type regimes, using electrolyte gating. While we found the electrical conductivity along the nanotube alignment direction to be several times larger than that in the perpendicular direction, the Seebeck coefficient was found to be fully isotropic, irrespective of the Fermi level position. We provide an explanation for this striking difference in anisotropy between the conductivity and the Seebeck coefficient using Mott's theory of hopping conduction. Our experimental evidence for an isotropic Seebeck coefficient in an anisotropic nanotube assembly suggests a route toward controlling the thermoelectric performance of carbon nanotube thin films through morphology control.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

First-principles calculations of thermal, electrical, and thermoelectric transport properties of semiconductors

The transport properties of semiconductors are key to the performance of many solid-state devices (transistors, data storage, thermoelectric cooling and power generation devices, etc). An understanding of the transport details can lead to material designs with better performances. In recent years simulation tools based on first-principles calculations have been greatly improved, being able to obtain the fundamental ground-state properties of materials (such as band structure and phonon dispersion) accurately. Accordingly, methods have been developed to calculate the transport properties based on an ab initio approach. We focus on the thermal, electrical, and thermoelectric transport properties of semiconductors, which represent the basic transport characteristics of the two degrees of freedom in solids—electronic and lattice degrees of freedom. Starting from the coupled electron-phonon Boltzmann transport equations, we illustrate different scattering mechanisms that change the transport features and review the first-principles approaches that solve the transport equations. We then present the first-principles results on the thermal and electrical transport properties of semiconductors. The discussions are grouped based on different scattering mechanisms including phonon-phonon scattering, phonon scattering by equilibrium electrons, carrier scattering by equilibrium phonons, carrier scattering by polar optical phonons, scatterings due to impurities, alloying and doping, and the phonon drag effect. We show how the first-principles methods allow one to investigate transport properties with unprecedented detail and also offer new insights into the electron and phonon transport. The current status of the simulation is mentioned when appropriate and some of the future directions are also discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Enhancement of thermoelectric figure of merit in β-Zn{sub 4}Sb{sub 3} by indium doping control

We demonstrate the control of phase composition in Bridgman-grown β-Zn{sub 4}Sb{sub 3} crystals by indium doping, an effective way to overcome the difficulty of growing very pure β-Zn{sub 4}Sb{sub 3} thermoelectric material. The crystal structures are characterized by Rietveld refinement with synchrotron X-ray diffraction data. The results show an anisotropic lattice expansion in In-doped β-Zn{sub 4}Sb{sub 3} wherein the zinc atoms are partially substituted by indium ones at 36f site of R-3c symmetry. Through the elimination of ZnSb phase, all the three individual thermoelectric properties are simultaneously improved, i.e., increasing electrical conductivity and Seebeck coefficient while reducing thermal conductivity. Under an optimal In concentration (x = 0.05), pure phase β-Zn{sub 4}Sb{sub 3} crystal can be obtained, which possesses a high figure of merit (ZT) of 1.4 at 700 K.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Observation of an Unexpected n -Type Semiconducting Behavior in the New Ternary Zintl Phase Eu 3 InAs 3

The ternary arsenides Eu 3 InAs 3 and Sr 3 InAs 3 have been obtained by reactions of the elements in In flux at 1373 K. Structure elucidation by single-crystal X-ray diffraction reveals that Eu 3 InAs 3 and Sr 3 InAs 3 adopt the same orthorhombic structure (space group Pnma, Z = 4, Ca 3 AlAs 3 structure type) with unit cell parameters a = 12.9179(9) Å, b = 4.3990(3) Å, c = 13.9337(10) Å and a = 13.0218(11) Å, b = 4.4364(4) Å, c = 14.1339(12) Å, respectively. The structure consists of linear chains of corner-sharing InAs4 tetrahedra, [InAs 2 As 2/2 ] 6– , and Eu 2+ /Sr 2+ cations. Therefore, both Eu 3 InAs 3 and Sr 3 InAs 3 are valence-precise Zintl phases. As expected from the closed-shell electronic configurations, semiconducting behavior is confirmed by resistivity measurements on single crystals for both and by electronic band structure calculations for Sr 3 InAs 3 . The temperature dependence of resistivity and the computational work are in agreement that Eu 3 InAs 3 and Sr 3 InAs 3 are intrinsic semiconductors with narrow band gaps. Thermopower measurement on single-crystalline samples of Eu 3 InAs 3 shows that in the whole measured temperature range, from 300 to 700 K, the values for the Seebeck coefficient are negative. The observation of a negative Seebeck coefficient with very large absolute value (>400–500 μV K –1 at 700 K) is unexpected among the Zintl phases and suggestive that electrons are the majority charge carriers. Such a rare, n-type charge transport in an undoped compound such as Eu 3 InAs 3 , a material that has not been purposely optimized, could indicate native “defect” chemistry, and not extrinsic doping, as a reason for the unusual behavior. Here, a possible explanation involves a mixed-valent Eu 2+ /Eu 3+ state, which might be inferred from the measured effective paramagnetic moment of 7.2 μB per Eu atom, which is lower than the theoretically predicted value for free-ion moment of 7.9 μ B /Eu.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2009

Very High Output Thermoelectric Devices Based on ITO Nanocomposites

A material having useful thermoelectric properties was synthesized by combining indium-tin-oxide (ITO) with a NiCoCrAlY alloy/alumina cermet. This material had a very large Seebeck coefficient with electromotive-force-versustemperature behavior that is considered to be excellent with respect to utility in thermocouples and other thermoelectric devices. When deposited in thin-film form, ceramic thermocouples offer advantages over precious-metal (based, variously, on platinum or rhodium) thermocouples that are typically used in gas turbines. Ceramic thermocouples exhibit high melting temperatures, chemical stability at high temperatures, and little or no electromigration. Oxide ceramics also resist oxidation better than metal thermocouples, cost substantially less than precious-metal thermocouples, and, unlike precious-metal thermocouples, do not exert catalytic effects.

Fralick, Gustave↗
DOE OSTI2024

Influence of metal organic framework glasses on thermoelectric properties of AgSb 0.96 Zn 0.04 Te 2 alloy

In recent years, a significant number of chalcogenides-based thermoelectric (TE) materials have been investigated theoretically and experimentally. However, the efficiency of TE materials is often limited by physical and chemical stability issues. Therefore, it is crucial to identify additive materials that can reduce thermal conductivity and improve the efficiency of crystalline TE materials. One well-known approach to lower thermal conductivity is introducing porosity into the material structure, which helps scatter phonon energy. Metal-organic framework (MOF) crystalline materials, known for their porosity and physical and chemical stability, offer unique advantages in TE applications. In this study, we investigate the influence of 20 weight% amorphous Zeolitic Imidazolate Framework (ZIF)-62 to p-type AgSb 0.96 Zn 0.04 Te 2 (ASTZ), a well-known TE material. We synthesized composites, ASTZ, ASTZ-Zn, and ASTZ-Co, by sintering ASTZ with amorphous ZIF-62(Zn) and ZIF-62(Co) respectively. The addition of amorphous ZIF-62(Zn) leads to a significant enhancement in the Seebeck coefficient of ASTZ increasing from 151 µV/K to 229 µV/K at 586K. Moreover, the thermal conductivity of the ASTZ TE materials drops drastically from 0.491 Wm -1 K -1 to around 0.22 Wm -1 K -1 at 623K with the addition of either amorphous ZIF-62(Zn) or ZIF-62(Co). Remarkably, ASTZ containing amorphous ZIF-62(Zn) achieves a maximum thermoelectric figure of merit (zT max ) of approximately 0.078 at 573K, surpassing any MOF-based thermoelectric material reported to date. In conclusion, these findings highlight the potential of amorphous ZIF-62 as an effective additive for enhancing the properties of thermoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Thickness dependent quantum oscillations of transport properties in topological insulator Bi{sub 2}Te{sub 3} thin films

The dependences of the electrical conductivity, the Hall coefficient, and the Seebeck coefficient on the layer thickness d (d = 18−600 nm) of p-type topological insulator Bi{sub 2}Te{sub 3} thin films grown by thermal evaporation in vacuum on glass substrates were obtained at room temperature. In the thickness range of d = 18–100 nm, sustained oscillations with a substantial amplitude were revealed. The observed oscillations are well approximated by a harmonic function with a period Δd = (9.5 ± 0.5) nm. At d > 100 nm, the transport coefficients practically do not change as d is increased. The oscillations of the kinetic properties are attributed to the quantum size effects due to the hole confinement in the Bi{sub 2}Te{sub 3} quantum wells. The results of the theoretical calculations of Δd within the framework of a model of an infinitely deep potential well are in good agreement with the experimental results. It is suggested that the substantial amplitude of the oscillations and their sustained character as a function of d are connected with the topologically protected gapless surface states of Bi{sub 2}Te{sub 3} and are inherent to topological insulators.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Revealing the optoelectronic and thermoelectric properties of the Zintl quaternary arsenides ACdGeAs{sub 2} (A = K, Rb)

Highlights: • Zintl tetragonal phase ACdGeAs{sub 2} (A = K, Rb) are chalcopyrite and semiconductors. • Their direct band gap is suitable for PV, optolectronic and thermoelectric applications. • Combination of DFT and Boltzmann transport theory is employed. • The present arsenides are found to be covalent materials. - Abstract: Chalcopyrite semiconductors have attracted much attention due to their potential implications in photovoltaic and thermoelectric applications. First principle calculations were performed to investigate the electronic, optical and thermoelectric properties of the Zintl tetragonal phase ACdGeAs{sub 2} (A = K, Rb) using the full potential linear augmented plane wave method and the Engle–Vosko GGA (EV–GGA) approximation. The present compounds are found semiconductors with direct band gap and covalent bonding character. The optical transitions are investigated via the dielectric function (real and imaginary parts) along with other related optical constants including refractive index, reflectivity and energy-loss spectrum. Combining results from DFT and Boltzmann transport theory, we reported the thermoelectric properties such as the Seebeck’s coefficient, electrical and thermal conductivity, figure of merit and power factor as function of temperatures. The present chalcopyrite Zintl quaternary arsenides deserve to be explored for their potential applications as thermoelectric materials and for photovoltaic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thermal and thermoelectric properties of an antiferromagnetic topological insulator MnBi 2 Te 4

The discovery of an intrinsic antiferromagnetic topological insulator (AFMTI) in MnBi 2 Te 4 has attracted intense attention, most of which lies in its electrical properties. Here in this paper, we report electronic, thermal, and thermoelectric transport studies of this newly found AFMTI. The temperature and magnetic field dependence of its resistivity, thermal conductivity, and Seebeck coefficient indicate strong coupling between charge, lattice, and spin degrees of freedom in this system. Furthermore, MnBi 2 Te 4 exhibits a large anomalous Nernst signal, which is associated with nonzero Berry curvature of the field-induced canted antiferromagnetic state.

36 MATERIALS SCIENCE↗