Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SCANNING ELECTRON MICROSCOPY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Interdiffusion and Formation of Intermetallic Compounds in High-Temperature Power Electronics Substrate Joints Fabricated by Transient Liquid Phase Bonding

Power electronics packages typically comprise a dielectric substrate bonded to a metal layer and attached to heat sinks using a low-thermal-conductivity solder. These multiple layers increase the effective thermal resistance of the package and are responsible for package failures under cyclic thermal loads. Bonding the aluminum nitride dielectric layer (AlN) directly to a low coefficient of thermal expansion (CTE) aluminum silicon carbide (AlSiC) cold plate using copper-aluminum (Cu-Al) transient liquid phase (TLP) bonding has been shown to improve the mechanical reliability of the power electronic packages while making the package more compact by bringing the cooling solutions closer to the devices. This study aims to characterize the Cu-Al bonds formed during the TLP bonding of AlSiC with three different power electronics substrates: pure aluminum nitride (AlN), aluminum (DBA), and copper (DBC). The material compositions and microstructures of the bonds were analyzed using scanning electron microscopy (SEM), x-ray spectroscopy (EDS), confocal scanning acoustic microscopy (C-SAM), and x-ray diffraction (XRD). ..alpha..-Al solid compound was identified as the dominant phase in AlN-AlSiC and Al-AlSiC, with a notable presence of SiC particles. In contrast, three intermetallic phases - ..theta..-CuAl2, ..eta..-CuAl, and ..gamma..'- Cu9Al4 - were observed in the Cu-AlSiC bond. A computational solid-state diffusion model was developed to predict the intermetallic compounds (IMCs) formed during Cu-Al TLP bonding in each system, which supported the observation that an initial Cu volume fraction of 20 % in the material layers produced a final bond composition of >95 % Al with minimal IMC growth. However, increased Cu concentrations produced higher concentration gradients, leading to increased growth of IMCs, Kirkendall voids, and interstitial cracks.

DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Effect of polycarboxylate ether on the expansion of ye'elimite hydration in the presence of anhydrite

Polycarboxylate ether (PCE), a commonly used superplasticizer, is known to influence the morphology of ettringite during the early hydration of C{sub 3}A- and ye'elimite-containing cements. According to existing theories, such morphological changes may be crucial to the expansive behavior of these cements. This paper studied the expansion of ye'elimite-anhydrite pastes and found the use of PCE to reduce expansion after 4 days of curing. Hydration studies were conducted by calorimetry, X-ray diffractometry, scanning electron microscopy, mercury intrusion porosimetry, inductively coupled plasma–optical emission spectrometry, and X-ray microtomography. The results show that the influences of PCE on the morphology of ettringite and the hydration of ye'elimite were quite small after 2 days. Based on the crystal growth theory, the range of pores in which ettringite can grow was calculated to explain the observed expansive behaviors. The presence of ettringite nano-crystals in aluminum hydroxide was also revealed and considered as a possible expansion mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Evaluating genetic and environmental controls on silicon accumulation in Populus trichocarpa leaves

Background and aims: Silicon (Si) accumulation and formation of non-crystalline silica particles (phytoliths) inside plant cells contribute to plant function, soil carbon storage, and Si reservoirs in soils. A better understanding of how genetic and environmental factors control Si accumulation may improve understanding of Si cycling between plants and soil and its impacts on other ecosystem processes. Methods: This study examined how genetic potential for Si uptake and silicification translated to Si concentrations and phytolith formation in Populus trichocarpa leaves. Leaves were collected from four different genotypes of cultivated poplar trees that were grown in a common garden and possess established differences in leaf-level gene expression related to Si transport and silicification. Scanning electron microscopy and subsequent image analysis were used to quantify Si concentrations and phytolith abundance and features. Results: Phytoliths were identified in nearly all leaves but were often absent at very low (< 0.5 wt.%) Si concentrations at the leaf surface. The proportion of leaf area occupied by phytoliths increased as Si content increased. Silicon content and phytolith abundance at the leaf surface did not vary across genotypes, but surface Si was weakly correlated with plant available Si in soil. Conclusion: Phytoliths were prevalent in P. trichocarpa leaves; however, the genetic potential for Si uptake and silicification at the leaf-level poorly predicted foliar Si and phytolith abundance. Uniformly low expression of Si uptake genes in the roots may have reduced differences across genotypes. Consequently, Si accumulation in leaves was likely more strongly influenced by soil Si bioavailability, phenology, or additional environmental factors.

Image analysis↗
DOE OSTI2025

Fabrication of porous transport electrodes: Development of quantitative approach for quality control

This work focuses on porous transport electrodes (PTEs), which integrate the anodic catalyst with the adjacent Ti porous transport layer (PTL). Challenges in catalyst deposition on PTLs, particularly at low loadings, motivated this study to evaluate various fabrication methods and characterization approaches. This work investigated Pt-treated PTLs coated with Ir-based catalysts using several common methods, including airbrush coating, rod coating, ultrasonic spray coating, electrodeposition, and sputter deposition, with catalyst loadings ranging from 2.9 to 0.1 mg/cm 2 , providing the opportunity for comparisons across a large set of samples produced by different methods. Two widely accessible characterization techniques: X-ray computed tomography (XCT) and scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) were explored. Initial evaluation of selected samples with XCT provided qualitative insights into catalyst distribution, however comprehensive quantitative analysis was limited. SEM-EDS enabled detailed information on the catalyst distribution both qualitatively and quantitatively using two metrics. Atomic and surface area % ratios of Pt:Ir and Ti:Ir revealed trends in catalyst loading and losses into the PTL pores, as well as evaluating the homogeneity of catalyst coatings. The analysis demonstrated that ultrasonic spray coating, electrodeposition, and sputter coating produced the most homogeneous coatings, with minimal catalyst losses observed for electrodeposition and sputter coating. By adapting common techniques with novel, standardized methodologies, this work establishes a universally applicable framework for cross-study comparison of PTEs. The SEM-EDS approach provides a practical, accessible tool for PTE characterization and contributes a reference dataset supporting both research development and rapid quality control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Investigation of process history and underlying phenomena associated with the synthesis of plutonium oxides using Vector Quantizing Variational Autoencoder

Accurate, high throughput, and unbiased analysis of plutonium oxide particles is needed for analysis of the phenomenology associated with process parameters in their synthesis. Compared to qualitative and taxonomic descriptors, quantitative descriptors of particle morphology through scanning electron microscopy (SEM) have shown success in analyzing process parameters of uranium oxides. Among other candidates, a neural network called a Vector Quantizing Variational Autoencoder (VQ-VAE) has shown the ability to quantitatively describe particle morphology to attain >85% accuracy in identifying uranium oxide processing routes. We utilize a VQ-VAE to quantitatively describe plutonium dioxide (PuO 2 ) particles created in a designed experiment and investigate their phenomenology and prediction of their process parameters. PuO 2 was calcined from Pu(III) oxalates that were precipitated under varying synthetic conditions that related to concentrations, temperature, addition and digestion times, precipitant feed, and strike order; the surface morphology of the resulting PuO 2 powders were analyzed by SEM. A pipeline was developed to extract and quantify useful image representations for individual particles with the VQ-VAE, then further reduce the dimensionality of the feature space using a bottlenecking neural network fit to perform multiple classification tasks simultaneously. The reduced feature space could predict process parameters with greater than 80% accuracies for some parameters with a single particle. They also showed utility for grouping particles with similar surface morphology characteristics together. Both the clustering and classification results reveal valuable information regarding which chemical process parameters chiefly influence the PuO 2 particle morphologies: strike order and oxalic acid feedstock. Doing the same analysis with multiple particles was shown to improve the classification accuracy on each process parameter over the use of a single particle, with statistically significant results generally seen with as few as four particles in a sample.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Ag-doped As–S–Se chalcogenide glasses: a correlative study of structural and dielectrical properties

This work is focused on investigating the effect of Ag doping on the dielectric and structural properties of the As–S–Se glass system and their suitability for potential applications in optoelectronics, such as electronic and switching components. A series of glasses from the system Agx(As40S30Se30)100-x (x = 5 at.% Ag) were prepared with melt-quenching technique. Morphological and compositional analysis was performed by scanning electron microscopy and energy-dispersive X-ray spectroscopy. Raman spectroscopy measurements have shown structural modifications of the glass network upon Ag doping, with creation of new Ag–(S,Se)–As structures, resulting in increased number of defect states. Variations in dielectric permittivity (e') and dielectric loss (e") were investigated in a wide frequency and temperature range, and explained by dominant dipolar and electronic polarization, as well as correlated with the observed structural changes. Improvement in dielectric properties is observed upon doping with Ag. Furthermore, the low dielectric tangent loss at high frequencies for all glassy samples points to a beneficial ability of the material to absorb energy of the external electric field. Good thermal stability of these glasses is confirmed by the calculated temperature coefficient of the dielectric permittivity. Density of localized states in all glasses was determined from AC conductivity and the dielectric tangent loss using a correlated barrier hopping model, and found to increase with Ag concentration. The overall results suggest that Ag doping enhances the electrical and optical quality of this type of glasses, making them suitable as nonlinear optical materials and their applications in devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Morphological and chemical characteristics of oxide scales formed on δ-Phase plutonium metal alloys I: 3.5 at% ga

Focused ion-beam scanning electron microscopy (FIB-SEM) and three-dimensional (3D) microscopy were applied to characterize the subsurface morphological features of oxide scales formed on an ~3.5 at.% Ga plutonium (Pu) metal alloy. Using the FIB-SEM technique, a number of morphological features formed in the interior of the oxide scale from Pu metal's environmental exposure were observed and identified. Here, Auger electron spectroscopy (AES) was utilized to characterize the cross-sectional composition and chemistry of the oxide scale. The oxide scale formed during inert storage and operational environments has a characteristic internal scale structure that includes a relatively dense oxide layer with some lateral and transverse cracking. Generally, after subsequent exposure to dry air environment, the oxide scale retained most of the original structural and chemical characteristics. However, after aging in a moist air environment, while the oxide scale was found to maintain the chemical characteristics of the source oxide, the scale was found to be on average thinner and without the previously observed internal microcracking, likely the result of spallation of the source scale during exposure to the new environment.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The effect of temperature and burnup on U-10Zr metallic fuel chemical interaction with HT-9: A SEM-EDS study

The fuel cladding chemical interaction (FCCI) between Uranium-Zirconium-based metallic fuel and cladding materials during in-pile service is one of the most constraining phenomena affecting the performance of this fuel system. In this study, we investigated the effect of temperature and burnup on the FCCI development in two U-10 wt.% Zr (U-10Zr) fuel samples with HT-9 cladding irradiated as part of the MFF-3 irradiation test in the Fast Flux Test Facility (FFTF). One sample achieved a burnup of 13.1 at.% and operated with an average inner cladding temperature of 530°C, while the other achieved a burnup of 8.5 at.% and was subjected to an average inner cladding temperature of 615°C. Automated scanning electron microscopy (SEM) back-scattered electron (BSE) imaging of entire fuel cross-sections and SEM energy dispersive x-ray spectroscopy (EDS) analysis on specific fuel-cladding interface regions successfully provided a comprehensive characterization of the depth and type of interaction happening under different irradiation conditions. Further, our analysis shows that FCCI development on both fuel and cladding side is strongly influenced by the inner cladding temperature and, to some extent, the formation and integrity of Zr-rich layers between the fuel and cladding, while the impact of burnup and power is negligible. Measured FCCI thicknesses were compared to BISON simulations using both an empirical model based upon legacy data from the Experimental Breeder Reactor II (EBR II) irradiations and a mechanistic model currently under development for the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, showing satisfactory agreement. Nonetheless, this comparison supports the need for additional microstructural characterization in intermediate ranges of temperature, power, and burnups in prototypic-length pins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Thermal Dehydration of Aluminum (Oxy)hydroxides on Fuel Cladding Material - 20200

The aluminum cladding of research-reactor fuel undergoes general corrosion with resulting formation of adherent aluminum (oxy)hydroxide films during in-reactor and post-discharge exposure to water under various conditions and temperatures. These (oxy)hydroxides contain chemically-bound water that poses challenges for extended dry storage due to the risk of thermal or radiolytic decomposition releasing free water and/or hydrogen and oxygen gases. This study comprised laboratory experiments of thermal drying behavior of aluminum (oxy)hydroxides to identify approaches for reducing bound water on fuel cladding prior to sealed dry storage. Effective drying strategies for adherent (oxy)hydroxides on fuel cladding will improve the safety of dry storage by mitigating potential avenues for additional corrosion and/or generation of flammable gases inside the storage canister. This work is part of a broader investigation to address knowledge gaps and technical data needs for dry storage of aluminum-clad spent nuclear fuel (ASNF), which included investigation of (oxy)hydroxide formation on aluminum alloy substrates immersed in water, characterization of service-grown films from ASNF, and radiolytic yield of hydrogen from (oxy)hydroxide powders and films. The current work comprises experimental thermal dehydration of aluminum trihydroxides (bayerite and gibbsite) characteristic of low-temperature (<80 deg. C) corrosion in water and aluminum oxyhydroxide (boehmite) characteristic of high temperature (>80 deg. C) corrosion in water. First, commercially produced (oxy)hydroxide powders (boehmite and gibbsite) were tested via thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The effort aimed to identify or confirm key temperature ranges/thresholds for the thermal decomposition reactions, as well as impacts of ramp rate and hold times, for drying of isolated, high-surface-area (oxy)hydroxides. The information gleaned from powder tests was used to guide subsequent drying tests on adherent (oxy)hydroxide films grown on aluminum alloy substrates. TGA was used to analyze small samples of the aluminum coupons with adherent (oxy)hydroxide films. Specimens were characterized both pre- and post-drying using X-ray diffraction (XRD) to determine the film composition and scanning electron microscopy (SEM) to determine its morphology. Drying of adherent (oxy)hydroxide films was anticipated to pose additional complications relative to drying of (oxy)hydroxide powders. Anticipated challenges include achieving sufficient drying of the (oxy)hydroxide at low-enough temperature to avoid melting or other undesirable phase changes in the aluminum substrate and overcoming transport limitations of water through the thickness of a dense film or through a tortuous pore structure to reach the outer surface of the film. Inn addition, dehydration of (oxy)hydroxides significantly changes the film density, which may lead to substantial alterations in the morphology, including potential cracking and spalling of the film. TGA/DSC tests of gibbsite powders resulted in successful conversion to boehmite or alumina, depending on the maximum temperature reached. At low ramp rates (≤5 deg. C/min), the conversion to boehmite occurred around 300 deg. C (210-340 deg. C). XRD confirmed that boehmite was the only phase detected after tests reaching 450 deg. C. The transition to alumina occurred around 510 deg. C (470-550 deg. C), with XRD detecting only alumina after tests reaching at least 600 deg. C. Boehmite powders dehydrated to alumina at about 400 deg. C (330-460 deg. C) for coarse (77-μm particle diameter) powder and about 490 deg. C (420-520 deg. C) for fine (0.7-μm particle diameter) powder. For all powders tested, the maximum percent mass loss after drying to high temperature slightly exceeded the theoretical mass loss for complete dehydration of the stoichiometric (oxy)hydroxide to alumina, which is likely attributable to physisorbed water in the powder. Drying of a thick (∼8.6 μm), predominantly bayerite adherent film displayed a dramatic change in film morphology, with the initially continuous trihydroxide film cracking into sections on the order of 50 μm square and partially delaminating. The outermost layer of the film completely faked of in some regions. The layer exposed under the spalled oxide also displayed prominent cracking, with spacing on the order of 10 μm, but this surface layer appeared to remain completely adhered to the aluminum substrate. TGA showed mass losses per unit surface area up to ∼1.0 mg/cm{sup 2}. XRD characterization of the remaining oxide was inconclusive, with no crystalline phases detected. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Optoelectronic and structural characterization of trapezoidal defects in 4H-SiC epilayers and the effect on MOSFET reliability

To this day, trapezoidal defects are found in clusters and high counts in wafers representing the industry standard in terms of material quality being produced. This study sheds light on the nature, origin, behavior, and impact of this defect on device yield and reliability. Trapezoidal defects in 4H-SiC epitaxial layers were investigated by photoluminescence (PL) imaging, scanning electron microscopy (SEM), cathodoluminescence spectrum imaging (CLSI), SEM electron beam induced current (EBIC) imaging, and by transmission electron microscopy (TEM) observation. The bar-shaped stacking faults were identified by the PL and CL measurements with a peak emission wavelength of 420 and 450 nm. An optoelectronic behavioral study based on the recombination enhanced dislocation glide mechanism revealed how expanding dislocations and stacking faults interact with each other. Combining the luminescence and microscopy results, the nature of the stacking faults was identified as being a combination of Shockley-type and Frank-type stacking faults. The TEM analysis showed that these defects originate from the substrate and the stacking sequences of some of the faults were determined as (…2, 4, 2…) and (…2, 3, 2…) in the Zhdanov's notation by high-resolution TEM. The origin of this defect is speculated based on our results and previous reports. The EBIC imaging showed that the high density of SFs in these towers is a strong site of carrier recombination, which presumably has an impact on the transfer characteristics of SiC devices. Furthermore, these defects have shown to impact metal oxide semiconductor field effect transistors electrical performance via an increase in the on-state resistance depending on the coverage percentage of the tower of defects in the active area of the device.

4H-SiC↗
DOE OSTI2021

Morphological and chemical characteristics of oxide scales formed on δ-phase plutonium metal alloys II: 2.0 at% Ga

The focused ion-beam scanning electron microscopy (FIB-SEM) and three-dimensional (3D) microscopy were applied to characterize the subsurface morphological features of oxide scales formed on an ~2.0 at. % Ga plutonium (Pu) metal alloy. Using the FIB-SEM technique, a number of morphological features formed in the interior of the oxide scale from Pu metal’s environmental exposure were observed and identified. Auger electron spectroscopy (AES) was utilized to characterize the cross-sectional composition and chemistry of the oxide scale. The oxide scale formed during inert storage and operational environments was found to be highly variable in thickness and morphology, presenting some regions with a thin (<400 nm), dense oxide layer and others with a thick (>2 µm) scale with substantial lateral cracking. After subsequent exposure to dry air environment, the oxide scale became thicker (~4 µm) and slightly more porous. The changes following aging in a moist air environment were observed to be more severe, with the formation of a highly porous internal structure containing significant lateral and transverse cracking. In comparison to the scale formed on an ~3.5 at. % Ga-Pu metal alloy, the oxide morphology of the lower gallium alloy investigated here exhibited greater variation in thickness and a noteworthy dependence on the presence of water vapor, particularly in terms of the internal porosity formed during growth of the oxide.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Patch-Based Convolutional Neural Networks for Multiple Microstructural Features Detection in FIB-SEM Micrographs of Irradiated Nuclear Fuel

Focused ion beam scanning electron microscopy (FIB-SEM) tomography has increasingly been utilized for acquiring three-dimensional (3D) microstructure features at the sub-micron scale in irradiated nuclear materials. This technique involves sequential ion beam slicing followed by electron beam imaging and compositional mapping using energy dispersive spectroscopy (EDS). Despite its growing use, several challenges persist. These include the time-intensive nature of data collection of EDS data, difficulties in distinguishing between various microstructures, and issues with image alignment. These challenges currently limit the broader application of FIB-SEM tomography in the field. To overcome these limitations, we propose using convolutional neural networks (CNNs) to automate microstructure identification in SEM images. Our study introduces a new framework for identifying microstructures in irradiated U-10Zr (wt. %) metallic fuel with limited annotated data. The framework includes the creation of a reliable annotated dataset with paired SEM and ground truth data from EDS maps, the applications of CNNs for microstructure identification, and the validation of model performance. Specifically, we employed the Segment Anything Model (SAM) to align SEM images with corresponding EDS maps and focused ion beam (FIB) tomography SEM data. We evaluate several models, including Patch-based U-Net, Attention U-Net, and Residual U-Net, finding that patch-based U-Net exhibits superior segmentation performance and consistency. This approach reduces reliance on EDS detectors and aids in accelerating nuclear material analysis process, highlighting the potential of advanced deep learning techniques to improve microstructural understanding in nuclear material. This is the first framework to integrate SAM and Patch-based CNN models for semantic segmentation of irradiated nuclear materials, with potential applicability to other tomography datasets.

36 - MATERIALS SCIENCE↗
NASA NTRS1987

Effect of LID (Registered) processing on the microstructure and mechanical properties of Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo titanium foil-gauge materials

A study was undertaken to determine the mechanical properties and microstructures resulting from Liquid Interface Diffusion (LID -Registered) processing of foil-gauge specimens of Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo coated with varying amounts of LID material. In addition, the effects of various elevated temperature exposures on the concentration profiles of the LID alloying elements were investigated, using specimens with a narrow strip of LID material applied to the surface. Room and elevated temperature tensile properties were determined for both coated and uncoated specimens. Optical microscopy was used to examine alloy microstructures, and scanning electron microscopy to examine fracture surface morphologies. The chemical concentration profiles of the strip-coated specimens were determined with an electron microprobe.

Balckburn, Linda B.↗
NASA NTRS1999

Structure and Morphology of Phthalocyanine Films Grown in Electrical Fields by Vapor Deposition

Phthalocyanine is a very stable organic material in the atmosphere and has been used in numerous applications, such as optical switching and optical storage devices. Although this material has already been discovered for several decades and has had extensive studies conducted on it, many properties still need to be better understood, for example, the mechanisms of forming different solid phases and of changing film morphology by external forces. Phthalocyanine has two preferred solid phases (alpha and beta phases) for which the crystal structures, surface morphology and optical properties are different. In order to investigate these phenomena and the relationship among them, phthalocyanine films have been synthesized by vapor deposition on quartz substrates with and without an external electrical field. Some substrates were coated with a very thin gold film for the electrical field. These films have been characterized using x-ray diffraction, scanning electron microscopy, Fourier transfer infrared spectroscopy, and Z-scan technique. The films have excellent chemical and thermal stability. However, the surface of these films grown without the electrical field shows flower-like morphology. When films are deposited under an electrical field (approximately 3000 V/cm), an aligned structure is revealed on the surface. A comparison of the structure, morphology, optical properties, and the growth mechanism for these films with and without an electrical field will be discussed.

Zhu, Shen↗
NASA NTRS2005

NSTAR Extended Life Test Discharge Chamber Flake Analysis

The Extended Life Test (ELT) of the NASA Solar Electric Propulsion Technology Readiness (NSTAR) ion thruster was concluded after 30,352 hours of operation. The ELT was conducted using the Deep Space 1 (DS1) back-up flight engine, a 30 cm diameter xenon ion thruster. Post-test inspection of the ELT engine revealed numerous contaminant flakes distributed over the bottom of the cylindrical section of the anode within the discharge chamber (DC). Extensive analyses were conducted to determine the source of the particles, which is critical to the understanding of degradation mechanisms of long life ion thruster operation. Analyses included: optical microscopy (OM) and particle length histograms, field emission scanning electron microscopy (FESEM) combined with energy dispersive spectroscopy (EDS), and atomic oxygen plasma exposure tests. Analyses of the particles indicate that the majority of the DC flakes consist of a layered structure, typically with either two or three layers. The flakes comprising two layers were typically found to have a molybdenum-rich (Mo-rich) layer on one side and a carbon-rich (C-rich) layer on the other side. The flakes comprising three layers were found to be sandwich-like structures with Mo-rich exterior layers and a C-rich interior layer. The presence of the C-rich layers indicates that these particles were produced by sputter deposition build-up on a surface external to the discharge chamber from ion sputter erosion of the graphite target in the test chamber. This contaminant layer became thick enough that particles spalled off, and then were electro-statically attracted into the ion thruster interior, where they were coated with Mo from internal sputter erosion of the screen grid and cathode components. Atomic oxygen tests provided evidence that the DC chamber flakes are composed of a significant fraction of carbon. Particle size histograms further indicated that the source of the particles was spalling of carbon flakes from downstream surfaces. Analyses of flakes taken from the downstream surface of the accelerator grid provided additional supportive information. The production of the downstream carbon flakes, and hence the potential problems associated with the flake particles in the ELT ion thruster engine is a facility induced effect and would not occur in the space environment.

deGroh, Kim K.↗
DOE OSTI2024

Embedding of Optical Fibers with Electric Field Assisted Sintering

The Electric Field Assisted Sintering (EFAS) technique was used for embedding the fibers, involving rapid heating via an electric current and pressure, reducing fiber exposure to high temperatures. Stainless steel guide tubes were inserted at the fiber-matrix junctions to prevent fiber breakage during the sintering process. The study varied key EFAS parameters—temperature (800°C to 980°C), pressure (40-50 MPa), and hold time (5-10 minutes)—to assess how they influenced fiber embedding. After embedding, the fibers were inspected using optical frequency domain reflectometry (OFDR) to evaluate optical losses and strain along the fiber length. The OFDR scans confirmed that the fibers remained intact, and subsequent transmission tests demonstrated no macroscopic fractures. The embedded samples were also analyzed using scanning electron microscopy (SEM) and X-ray computed tomography (CT) scans. These tests confirmed good bonding between the fiber and matrix with no cracking, though some porosity was present in samples fabricated at lower temperatures. At higher temperatures (980°C), the fiber-matrix bonding was continuous and defect-free, with metal coatings aiding in the bonding process. Elemental analysis showed interdiffusion between the fiber coatings and matrix materials, particularly between the gold coating and stainless steel. Helium leak tests revealed that lower sintering temperatures resulted in matrix porosity, causing leaks, but samples fabricated at 980°C were leak-tight.

46 - INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AN↗
NASA NTRS2012

Overview of C/C-SiC Composite Development for the Orion Launch Abort System

Past and present efforts by the authors to further understanding of the ceramic matrix composite (CMC) material used in the valve components of the Orion Launch Abort System (LAS) Attitude Control Motor (ACM) will be presented. The LAS is designed to quickly lift the Orion Crew Exploration Vehicle (CEV) away from its launch vehicle in emergency abort scenarios. The ACM is a solid rocket motor which utilizes eight throttleable nozzles to maintain proper orientation of the CEV during abort operations. Launch abort systems have not been available for use by NASA on manned launches since the last Apollo ]Saturn launch in 1975. The CMC material, carbon-carbon/silicon-carbide (C/C-SiC), is manufactured by Fiber Materials, Inc. and consists of a rigid 4-directional carbon-fiber tow weave reinforced with a mixed carbon plus SiC matrix. Several valve and full system (8-valve) static motor tests have been conducted by the motor vendor. The culmination of these tests was the successful flight test of the Orion LAS Pad Abort One (PA ]1) vehicle on May 6, 2010. Due to the fast pace of the LAS development program, NASA Marshall Space Flight Center assisted the LAS community by performing a series of material and component evaluations using fired hardware from valve and full ]system development motor tests, and from the PA-1 flight ACM motor. Information will be presented on the structure of the C/C-SiC material, as well as the efficacy of various non ]destructive evaluation (NDE) techniques, including but not limited to: radiography, computed tomography, nanofocus computed tomography, and X-ray transmission microscopy. Examinations of the microstructure of the material via scanning electron microscopy and energy dispersive spectroscopy will also be discussed. The findings resulting from the subject effort are assisting the LAS Project in risk assessments and in possible modifications to the final ACM operational design.

Allen, Lee R.↗
DOE OSTI2023

LDRD 22A1059-068FP Tailoring the Properties of Multi-Phase Materials Through the Use of Correlative Microscopy and Machine Learning - Poster

High strength alloys with good ductility, hardness, and toughness are needed to meet stringent design requirements for extreme environments. One complication in this pursuit is the evidence that metals rarely exhibit both high strength and good fracture toughness as the underlying mechanisms work in opposition. An exception to this behavior is found in multiphase alloys that form complex microstructures of mixed phases with variable grain sizes and shapes that provide increased fracture toughness by the arrangement of their constituent elements. We propose to explore this phenomenon using state-of-the-art machine learning (ML) techniques in a new and novel manner to identify and correlate the critical microstructural features in a Titanium-10Vanadium-2Iron-3Aluminum (Ti-10V-2Fe-3Al) alloy that is reported to exhibit high strength and fracture toughness. Additionally, we will employ multiple, complementary characterization techniques such as optical microscopy, electron backscatter diffraction (EBSD), energy dispersive spectroscopy (EDS) and scanning electron microscopy to provide multi-layer, quantitative ground truth measures of the microstructures. This data will be used to train a Convolutional Neural Network (CNN) in a semi-supervised environment to identify key microstructural features such as ? platelet dimensions and locations and ?/? phase boundaries and correlate those features with the strength and toughness. Here the ? and ? nomenclature refers to hexagonal close pack (hcp) and body center cubic (bcc) crystal structures, respectively. Previous work has focused on popular alloys and typically used one characterization technique. This research is focused on a promising titanium alloy, uses multiple complimentary characterization tools to provide precise microstructural information and correlates to improved fracture toughness. The resulting ML tool can be trained for additional microstructural features, different alloy(s), and or target mechanical properties.

36 MATERIALS SCIENCE↗