Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROCK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Effect of leading edge roundness on a delta wing in wing-rock motion

The effect of wing leading-edge roundness on wing rock was investigated using flow visualization in a water tunnel. Eighty degree delta wing models were tested on free-to-roll and forced oscillation rigs. The onset of wing rock was delayed by increasing the roundness of the leading edges. The wing rock amplitude and frequency results suggested that damping was increased at lower angles of attack but reduced at higher angles of attack. Vortex lift-off and vortex breakdown, especially during dynamic situations, were strongly affected by the leading edge roundness. Different forms of wing rock motion could be sustained by combinations of vortex breakdown and vortex lift-off. Behaviors of the wing and vortex motions were explained by the influence of leading edge roundness on the separation location, vortex trajectory, and vortex breakdown.

Ng, T. Terry↗
NASA NTRS1990

Getting lunar ilmenite - From soils or rocks?

Lunar soils or rocks can be mined as sources of ilmenite for producing oxygen. However, separable crystals of loose ilmenite in lunar soils are rare (less than 2 percent) and small (less than 200 microns); most ilmenite in the regolith is locked together with silicate minerals as rock fragments. If fragmentation of rock sources must be attempted to win appreciable amounts of ilmenite (approximately 10 percent or more), selective collection of high-Ti basalt fragments larger than 1 cm for fragmentation and ilmenite beneficiation may be advantageous over extensive processing of fine lunar soil. Many alternative processing schemes for fragmenting rocks on the Moon have been proposed; one process which was tested early in the Apollo program successfully disaggregated lunar and terrestrial basalts by passive exposure to low-pressure alkali (K) vapor. This process is worthy of reinvestigation.

Vaniman, D. T.↗
NASA NTRS1991

Wing rock suppression using forebody vortex control

Static and free-to-roll tests were conducted in a water tunnel with a configuration that consisted of a highly-slender forebody and 78-deg sweep delta wings. Flow visualization was performed and the roll angle histories were obtained. The fluid mechanisms governing the wing rock of this configuration were identified. Different means of suppressing wing rock by controlling the forebody vortices using small blowing jets were also explored. Steady blowing was found to be capable of suppressing wing rock, but significant vortex asymmetries had to be induced at the same time. On the other hand, alternating pulsed blowing on the left and right sides of the forebody was demonstrated to be potentially an effective means of suppressing wing rock and eliminating large asymmetric moments at high angles of attack.

Ng, T. T.↗
NASA NTRS1993

An aerodynamic model for one and two degree of freedom wing rock of slender delta wings

The unsteady aerodynamic effects due to the separated flow around slender delta wings in motion were analyzed. By combining the unsteady flow field solution with the rigid body Euler equations of motion, self-induced wing rock motion is simulated. The aerodynamic model successfully captures the qualitative characteristics of wing rock observed in experiments. For the one degree of freedom in roll case, the model is used to look into the mechanisms of wing rock and to investigate the effects of various parameters, like angle of attack, yaw angle, displacement of the separation point, and wing inertia. To investigate the roll and yaw coupling for the delta wing, an additional degree of freedom is added. However, no limit cycle was observed in the two degree of freedom case. Nonetheless, the model can be used to apply various control laws to actively control wing rock using, for example, the displacement of the leading edge vortex separation point by inboard span wise blowing.

Hong, John↗
NASA NTRS1992

Prediction and control of slender-wing rock

The unsteady Euler equations and the Euler equations of rigid-body dynamics, both written in the moving frame of reference, are sequentially solved to simulate the limit-cycle rock motion of slender delta wings. The governing equations of the fluid flow and the dynamics of the present multidisciplinary problem are solved using an implicit, approximately-factored, central-difference-like, finite-volume scheme and a four-stage Runge-Kutta scheme, respectively. For the control of wing-rock motion, leading-edge flaps are forced to oscillate anti-symmetrically at prescribed frequency and amplitude, which are tuned in order to suppress the rock motion. Since the computational grid deforms due to the leading-edge flaps motion, the grid is dynamically deformed using the Navier-displacement equations. Computational applications cover locally-conical and three-dimensional solutions for the wing-rock simulation and its control.

Kandil, Osama A.↗
NASA NTRS1993

Experimental and numerical analysis of the wing rock characteristics of a 'wing-body-tail' configuration

Free-to-roll wind tunnel tests were conducted and a computer simulation exercise was performed in an effort to investigate in detail the mechanism of wing rock on a configuration that consisted of a highly-slender forebody and a 78 deg swept delta wing. In the wind tunnel test, the roll angle and wing surface pressures were measured during the wing rock motion. A limit cycle oscillation was observed for angles of attack between 22 deg and 30 deg. In general, the wind tunnel test confirmed that the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. The variation of roll acceleration (determined from the second derivative of the roll angle time history) with roll angle clearly showed the energy balance necessary to sustain the limit cycle oscillation. Pressure measurements on the wing revealed the hysteresis of the wing rock process. First, second and nth order models for the aerodynamic damping were developed and examined with a one degree of freedom computer simulation. Very good agreement with the observed behavior from the wind tunnel was obtained.

Suarez, Carlos J.↗
NASA NTRS1993

Measurements of cosmogenic nuclides in lunar rock 64455

Eleven samples were ground from the glass coated surface of lunar rock 64455,82 with an average depth resolution of 50 microns and were measured for Be-10, Al-26, and Cl-36 using AMS (accelerator mass spectrometry). Results show no evidence of SCR (solar cosmic ray) effects. The flat cosmogenic nuclide profiles and activity levels are consistent with a 2 My exposure history for the rock and a sample location on the bottom of the rock. These AMS measurements are some of the most precise ever obtained for these three nuclides. This precision and the demonstrated fine depth resolution will enable us to conduct a number of detailed studies of depth effects in lunar and meteoritic samples, including investigating SCR effects in the surface exposed top of the glass coating of 64455 and possibly in the underlying rock.

Arnold, J. R.↗
NASA NTRS1993

Delimitation of terrestrial impact craters by way of pseudotachylytic rock distribution

The determination of the shape and size of terrestrial impact craters is problematic, yet is critical to understanding cratering mechanics and for scaling bolide mass, volume, and impact velocity with crater size and target response. The problem is particularly difficult in older geological terrains (e.g. Precambrian) which are more likely to have suffered post-impact deformation and hence distortion of the original structure and/or where weathering may have partly removed or obscured its original shape. Traditionally, a number of features are used to assist us in determining the shape and size of an impact structure. These include the following: (1) the occurrence of faults, especially those disposed concentrically relative to the crater--the outermost ring faults being interpreted as indicating a viable minimum diameter; and (2) the development of so-called breccias, some of which are also associated with faults (e.g. the Sudbury Breccia developed within the target rocks of the Sudbury Structure of Onta rio, Canada). 'Breccia' is not a satisfactory term because a number of breccia-types exist at impact sites (e.g. fall-back breccias and in-situ brecciated target material). Of relevance to crater diameter determination is the recognition of discrete zones and fault- and shock-related pseudotachylyte. Pseudotachylyte is a rock type comprising a fine-grained, usually dark matrix containing clasts of minerals and/or rock derived from the country rock target material. It origin is normally attributed to high-speed slip (including vibration) along a slip surface (i.e. fault) or to the passage of a shock wave through the host material. The clasts can occur as angular fragments (i.e. like a breccia), but are more commonly developed as rounded to sub-rounded fragments. Significantly, the scale of these pseudotachylytes can range from sub-millimeter thick veinlets to dyke-like bodies up to 1 km or more thick. It is the latter, larger occurrence which has been referred to as 'breccia.' The smaller-sized occurrence is generally not recognized in the field, nor is it traditionally associated with its larger counterpart.

Spray, John G.↗
NASA NTRS1993

Evaluation of lunar rocks and soils for resource utilization: Detailed image analysis of raw materials and beneficiated products

The rocks and soils of the Moon will be the raw materials for fuels and construction needs at a lunar base. This includes sources of materials for the generation of hydrogen, oxygen, metals, and other potential construction materials. For most of the bulk material needs, the regolith, and its less than 1 cm fraction, the soil, will suffice. But for specific mineral resources, it may be necessary to concentrate minerals from rocks or soils, and it is not always obvious which is the more appropriate feedstock. Besides an appreciation of site geology, the mineralogy and petrography of local rocks and soils is important for consideration of the resources which can provide feedstocks of ilmenite, glass, agglutinates, anorthite, etc. In such studies, it is very time-consuming and practically impossible to correlate particle counts (the traditional method of characterizing lunar soil petrography) with accurate modal analyses and with mineral associations in multi-mineralic grains. But x ray digital imaging, using x rays characteristic of each element, makes all this possible and much more (e.g., size and shape analysis). An application of beneficiation image analysis, in use in our lab (Oxford Instr. EDS and Cameca SX-50 EMP), was demonstrated to study mineral liberation from lunar rocks and soils. Results of x ray image analysis are presented.

Taylor, Lawrence A.↗
NASA NTRS1993

Reverse polarity magnetized melt rocks from the Chicxulub impact structure, Yucatan Peninsula, Mexico

Further paleomagnetic data for core samples of melt rock recovered in the Petroleos Mexicanos (PEMEX) exploratory wells within the Chicxulub structure, northern Yucatan peninsula, Mexico are reported. A previous report by Sharpton showed that the rocks studied contain high iridium levels and shocked breccia clasts, and an Ar-40/Ar-39 age of 65.2 plus or minus 0.4 Ma. The geomagnetic polarity determined for two samples is reverse (R) and was correlated with chron 29R that includes the K/T boundary. Our present analysis is based on two samples from each of three clasts of the melt rock from PEMEX well Y6-N17 (1295 to 1299 m b.s.l.). This study concentrates on the vectorial nature and stability of the remanence (NRM), the magnetic mineralogy and remanence carriers (i.e., the reliability and origin of the record), and on the implications (correlation with expected paleolatitude and polarity). The relative orientation of the drill core samples with respect to the horizontal is known. Samples were stable under alternating field (AF) and thermal treatments, and after removal of a small component they exhibited single-vectorial behavior. The characteristic remanence inclinations show small dispersion and a mean value (-43 deg) in close agreement with the expected inclination and paleolatitude (derived from the North American apparent polar wander path). Isothermal remenence (IRM) acquisition experiments, Lowrie-Fuller tests, coercivity and unblocking temperature spectra of NRM and saturation IRM, susceptibility and Q-coefficient analyses, and the single-component nature indicate a dominant mineralogy of iron-rich titanomagnetites with single or pseduo-single domain states. The stable characteristic magnetization may be interpreted as a result of shock heating of the rock at the time of formation of the inpact structure and its polarity, age, and paleolatitude are consistent with a time about the K/T boundary.

Urrutia-Fucugauchi, Jaime↗
NASA NTRS1993

Rock magnetic properties of the Arunta Block, Central Australia, and their implication for the interpretation of long-wavelength magnetic anomalies

Rock magnetic and petrologic studies of a suite of deep crustal rocks from the Arunta Block of Central Australia reveal that the granulite grade rocks are in general much more magnetic than the amphibolite grade samples irrespective of bulk rock composition. The dominant magnetic mineral in all samples is relatively pure magnetite as determined from thermomagnetic and electron microprobe analysis. The bulk magnetic properties are typical of pseudosingle-domain to multidomain size material. The samples from our study have very large remanences compared to previous crustal magnetic studies, with the granulites having a median natural remanent magnetization of 4.1 A/m and Koenigsberger ratio of 7.2. These remanences are relatively resistant to the thermal demagnetization, with nearly 50 percent of the magnetization remaining after 400 C demagnetization. Thus remanence may contribute significantly to the observed magnetic anomalies, including long-wavelength magnetic anomalies, the source of which resides at depth and therefore at elevated temperature, where a thermoviscous remanant magnetization along the present-day field is likely to dominate.

Kelso, Paul R.↗
NASA NTRS1994

Observations, models, and mechanisms of failure of surface rocks surrounding planetary surface loads

Geophysical models of flexural stresses in an elastic lithosphere due to an axisymmetric surface load typically predict a transition with increased distance from the center of the load of radial thrust faults to strike-slip faults to concentric normal faults. These model predictions are in conflict with the absence of annular zones of strike-slip faults around prominent loads such as lunar maria, Martian volcanoes, and the Martian Tharsis rise. We suggest that this paradox arises from difficulties in relating failure criteria for brittle rocks to the stress models. Indications that model stresses are inappropriate for use in fault-type prediction include (1) tensile principal stresses larger than realistic values of rock tensile strength, and/or (2) stress differences significantly larger than those allowed by rock-strength criteria. Predictions of surface faulting that are consistent with observations can be obtained instead by using tensile and shear failure criteria, along with calculated stress differences and trajectories, with model stress states not greatly in excess of the maximum allowed by rock fracture criteria.

Schultz, R. A.↗
NASA NTRS1996

Measurement of proton production cross sections of (sup 10)Be and (sup 26)Al from elements found in lunar rocks

Cosmic rays penetrate the lunar surface and interact with the lunar rocks to produce both radionuclides and stable nuclides. Production depth profiles for long-lived radionuclides produce in lunar rocks are measured using Accelerator Mass Spectrometry (AMS). For a particular radionuclide these production depth profiles can be interpreted to give an estimate for the solar proton flux over a time period characterized by the half life of the radionuclide under study. This analysis is possible if and only if all the cross sections for the interactions of all cosmic ray particles with all elements found in lunar rocks are well known. In practice, the most important cross sections needed are the proton production cross sections, because 98% of solar cosmic rays and (similar to)87% of galactic cosmic rays are protons. The cross sections for the production of long-lived radionuclides were very difficult to measure before the development of AMS and only in recent years has significant progress been made in determining these essential cross sections. Oxygen and silicon are major constituents of lunar rocks. We have reported already C-14 production cross sections from O and Si for proton energies 25-500 MeV, and O(p,x)(sup 10)Be from 58 160 MeV[6]. Here we present new measurements for the cross sections O(p,x)Be-10,O(p,x)Be-7, Si(p,x)Be-7,Si(p,x)Al-26, and Si(p,x)Na-22 from approximately 30 - 500 MeV.

Sisterson, J. M.↗
NASA NTRS1994

Possible Halo Depictions in the Prehistoric Rock Art of Utah

In western American rock art the concentric circle symbol, which is widely regarded as a sun symbol, is ubiquitous. We provide evidence from Archaic and Fremont Indian rock art sites in northwestern Utah that at least one depiction was motivated by an observation of a complex halo display. Cirrus cloud optical displays are linked in both folklore and meteorology to precipitation-producing weather situations, which, in combination with an abundance of weather-related rock art symbolism, indicate that such images reflected the ceremonial concerns of the indigenous cultures for ensuring adequate precipitation. As has been shown to be the case with rock art rainbows, conventionalization of the halo image may have resulted in simple patterns that lacked recognizable details of atmospheric optical phenomena. However, in one case in which an Archaic-style petroglyph (probably 1500 yr or more old) satisfactorily reproduced a complicated halo display that contained parhelia and tangent arcs, sufficient geometric information is rendered to indicate a solar elevation angle of approx. 40 deg. at the time of observation.

Sassen, Kenneth↗
NASA NTRS1994

Petrology of Impact-Melt Rocks at the Chicxulub Multiring Basin, Yucatan, Mexico

Compositions and textures of melt rocks from the upper part of the Chicxulub structure are typical of melt rocks at other large terrestrial impact structures. Apart from variably elevated iridium concentrations (less than 1.5 to 13.5 +/- 0.9 ppb) indicating nonuniform dissemination of a meteoritic component, bulk rock and phenocryst compositions imply that these melt rocks were derived exclusively from continental crust and platform-sediment target lithologies. Modest differences in bulk chemistry among samples from wells located approximately 40 km apart suggest minor variations in relative contributions of these target lithologies to the melts. Subtle variations in the compositions of early-formed pyroxene and plagioclase also support minor primary differences in chemistry between the melts. Evidence for pervasive hydrothermal alteration of the porous mesostasis includes albite, K-feldspar, quartz, epidote, chlorite, and other phyllosilicates, as well as siderophile element-enriched sulfides, suggesting the possibility that Chicxulub, like Sudbury, may host important ore deposits.

Schuraytz, Benjamin C.↗
NASA NTRS1995

Cogenetic Rock Fragments from a Lunar Soil: Evidence of a Ferroan Noritic-Anorthosite Pluton on the Moon

The impact that produced North Ray Crater, Apollo 16 landing site, exhumed rocks that include relatively mafic members of the lunar ferroan anorthositic suite. Bulk and mineral compositions indicate that a majority of 2-4 mm lithic fragments from sample 67513, including impact breccias and monomict igneous rocks, are related to a common noritic-anorthosite precursor. Compositions and geochemical trends of these lithic fragments and of related samples collected along the rim of North Ray Crater suggest that these rocks derived from a single igneous body. This body developed as an orthocumulate from a mixture of cumulus plagioclase and mafic intercumulus melt, after the plagioclase had separated from any cogenetic mafic minerals and had become concentrated into a crystal mush (approximately 70 wt% plagioclase, 30 wt% intercumulus melt). We present a model for the crystallization of the igneous system wherein "system" is defined as cumulus plagioclase and intercumulus melt. The initial accumulation of plagioclase is analogous to the formation of thick anorthosites of the terrestrial Stillwater Complex; however, a second stage of formation is indicated, involving migration of the cumulus-plagioclase-intercumulus-melt system to a higher crustal level, analogous to the emplacement of terrestrial massif anorthosites. Compositional variations of the lithic fragments from sample 67513 are consistent with dominantly equilibrium crystallization of intercumulus melt. The highly calcic nature of orthocumulus pyroxene and plagioclase suggests some reaction between the intercumulus melt and cumulus plagioclase, perhaps facilitated by some recrystallization of cumulus plagioclase. Bulk compositions and mineral assemblages of individual rock fragments also require that most of the mafic minerals fortned in close contact with cumulus plagioclase, not as separate layers. The distribution of compositions (and by inference, modes) has a narrow peak at anorthosite and a broader, larger peak at noritic anoilhosite. Characteristics of the samples and their geochemical trends imply an origin in a system that was large relative to the (unknown) size of the impact that produced the breccias of ferroan noritic-anorthosite composition that were excavated later by the formation of North Ray Crater, and they appear to be consistent with an origin of the suite within a perched plagioclase cumulate. If the Moon's crust formed by accumulation of plagioclase in a magma ocean, ferroan noritic anothosite, formed as an orthocumulate, is an alternative to extensive adcumulus formation of ferroan anorthosite (greater than 90 vol% plagiclase). This provides a relatively mafic ferroan anorthositic component (approximately 15 vol% mafics), which is required by mass-balance models of compositions of polymict lunar-crustal materials. The inferred bulk composition of the system of cumulus plagioclase and intercumulus melt is similar to that of ferroan regolith breccia MacAlpine Hills 88104/5, a lunar-highland meteorite, and may represent a common and widespread component of the Moon's early highland crust.

Jolliff, B. L.↗
NASA NTRS1999

Spectroscopic Properties of Metamorphosed Mafic Rocks: Remote Sensing Applications on Mars

Reflectance spectroscopy in the visible and near-infrared wavelengths, between 420 mn to 2588 nm. was utilized on a suite of hydrothermally metamorphosed mafic rocks from the Smartville complex in the northern Sierra Nevada mountains in California. A detailed data base of 102 samples was compiled in order to distinguish differences in mineralogy, petrology, and degree of metamorphism for remote sensing applications. Study was limited to metaigneous and metasedimentary rocks in an attempt to spectrally characterize terrestrial rocks analogous to the possible surface of Mars, for a better understanding and possible detection of the geologic features on the remote surface. Diagnostic absorption bands of iron, water, and hydroxyl produced the majority of discernible features in this study. Mossbauer spectroscopy was performed in order to determine specific iron sites. The resulting spectral data base along with thin section mineral identification, metamorphic zone, rock type and location were recorded and available for future application and research. Continued exploration of Mars in the advancing years, will further advance our understanding of the geology of Mars. Spectroscopic techniques will undoubtedly be integral parts of these future missions. Work on terrestrial analogs to the Martian surface must continue, in order to produce extensive data bases and broaden our knowledge of spectral features.

Graff, Trevor G.↗
NASA NTRS1999

A Model for Generation of Martian Surface Dust, Soil and Rock Coatings: Physical vs. Chemical Interactions, and Palagonitic Plus Hydrothermal Alteration

This model is one of many possible scenarios to explain the generation of the current surface material on Mars using chemical, magnetic and spectroscopic data from Mars and geologic analogs from terrestrial sites. One basic premise is that there are physical and chemical interactions of the atmospheric dust particles and that these two processes create distinctly different results. Physical processes distribute dust particles on rocks, forming physical rock coatings, and on the surface between rocks forming soil units; these are reversible processes. Chemical reactions of the dust/soil particles create alteration rinds on rock surfaces or duricrust surface units, both of which are relatively permanent materials. According to this model the mineral components of the dust/soil particles are derived from a combination of "typical" palagonitic weathering of volcanic ash and hydrothermally altered components, primarily from steam vents or fumeroles. Both of these altered materials are composed of tiny particles, about 1 micron or smaller, that are aggregates of silicates and iron oxide/oxyhydroxide/sulfate phases. Additional information is contained in the original extended abstract.

Bishop, J. L.↗