Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymer morphology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Development of a Printable Prill Formulation Technique and Demonstration of Monomodal Prill Size on Compaction Density and Compressive Strength

Polymer-bonded explosive molding powder, or “prills,” are relied on for the fabrication of pressed high explosives since the 1950's. The wet granulation technique, also known as “slurry coating,” that is used to formulate prills, is a complex process that results in polydisperse and variable yields. This makes it difficult to study the mesoscale effect that prills have on the microstructure of a pressed article. The following study introduces a novel approach to energetic granulation that leverages techniques used in the additive manufacturing of paste-like energetic materials. This extrusion granulation, or prill printing technique, makes it possible to tailor the sizes and shapes of prills, allowing for their morphological influences to be studied in a controlled manner. The following work details the fabrication and characterization of four monomodal size lots of prills using an inert formulation (95 wt.% melamine, 5 wt.% polymer binder). Prills from each size lot were die-pressed using a fixed recipe to investigate how prill size impacts compaction density and therefore compressive strength. It was found that larger prills influence the pressing density by creating larger defects within the microstructure of a pressed article, resulting in a decrease in compressive strength.

direct ink write↗
DOE OSTI2024

Structure-property relationship between lignin structures and properties of 3D-printed lignin composites

Lignin is a low-cost and renewable bioresource with a huge annual production promising to prepare sustainable materials. However, the poor interfacial adhesion between many lignin-polymer pairs deteriorates the mechanical performance of the composites, which seriously limits the application of lignin in 3D printing via fused depositional modeling. This work examined lignin-polyamide 12 (PA 12) intermolecular interactions (e.g., hydrogen bonding) to address the interface challenge. To realize this goal, the phenolic hydroxyl content was increased for a kraft softwood lignin using a LiBr/HBr demethylation procedure, increasing phenoxy content by 61.7%. Increased hydrogen bonding interactions between modified lignin (Pine-Lig-OH) and PA 12 demonstrated a significantly improved molten dynamic modulus by rheological analysis. Regarding mechanical properties, by adding 20 wt% of Pine-Lig-OH, the tensile strength and Young's modulus reached 46.6 MPa and 1.62 GPa, 30.2% and 33.9% higher than PA 12, respectively. Further morphological analysis proved the interfacial interactions are enhanced by showing the difference in the phase gaps. The dynamic mechanical analysis (DMA) supported the conclusion that Pine-Lig-OH could interact with polymer chains, alternating segmental movements due to the strong interaction. Here, this study presents a method to enhance lignin composite properties by promoting interactions with the polymer matrix through modified functional groups, guiding future lignin composite research.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Viscoelastic characterization of thin-film polymers exposed to low Earth orbit

The materials made available through the Long Duration Exposure Facility (LDEF) satellite provide a set of specimens that can be well characterized and have a known exposure history with reference to atomic oxygen and ultraviolet radiation exposure. Mechanical characteristics measured from control samples and exposed samples provide a data base for predicting the behavior of polymers in low earth orbit. Samples of 1.0 mil thick low density polyethylene were exposed to the low earth orbit environment for a period of six years. These materials were not directly exposed to ram atomic oxygen and offer a unique opportunity for measuring the effect of atomic oxygen and UV radiation on mechanical properties with little concern to the effect of erosion. The viscoelastic characteristics of these materials were measured and compared to the viscoelastic characteristics of control samples. To aid in differentiating the effects of changes in crystallinity resulting from thermal cycling, from the effects of changes in chemical structure resulting from atomic oxygen/UV attack to the polymer, a second set of control specimens, annealed to increase crystallinity, were measured as well. The resulting characterization of these materials will offer insight into the impact of atomic oxygen/UV on the mechanical properties of polymeric materials. The viscoelastic properties measured for the control, annealed, and exposed specimens were the storage and loss modulus as a function of frequency and temperature. From these datum is calculated the viscoelastic master curve derived using the principle of time/temperature superposition. Using the master curve, the relaxation modulus is calculated using the method of Ninomiya and Ferry. The viscoelastic master curve and the stress relaxation modulus provide a direct measure of the changes in the chemical or morphological structure. In addition, the effect of these changes on long-term and short-term mechanical properties is known directly. It should be noted that the dependence on directionality for the polymer films was considered since these films were manufactured by a blown-film process.

Letton, Alan↗
DOE OSTI2023

Structure and dynamics of ILs-based gel polymer electrolytes and its enhanced conductive properties with the incorporation of Al 2 O 3 nanofibers

Here, this work reports the enhanced mobility of ions in ionic liquid (IL)-based gel polymer electrolytes (GPEs) with the incorporation of Al 2 O 3 nanofibers. A combination of PVDF-HFP, EMIMTFSI and LiTFSI with 3 wt% Al 2 O 3 nanofibers has been prepared through solution casting technique. The room temperature ionic conductivity of PVDF-HFP: ILs electrolyte (45:55, weight ratio of 0.82) (GPE) is found to be 2.7 × 10 –5 S cm –1 , which increases up to 7.8 × 10 –5 S cm –1 in Al 2 O 3 containing GPE (Al-GPE). Pulsed field gradient (PFG) NMR results validate the increased ionic conductivity observed in Al-GPE. We found that the diffusivity of Li + , TFSI – and EMIM + increases when Al 2 O 3 nanofibers are well-distributed in the GPE matrix. The surface morphology and the amorphicity of GPEs are examined through SEM and XRD analyses. Lastly, the local structure of Al 2 O 3 fibers and the molecular-level interactions of ions with polymer, and their effect on the diffusivity of ions are established through solid-state NMR detecting 27 Al, 1 H, 13 C, 19 F nuclei including 2D 13 C{ 1 H} HETCOR NMR experiments. The 13 C DPMAS and CPMAS experiments highlight the dynamic heterogeneity associated with the ions that are embedded in the rigid and the mobile phase of GPEs. While some of the ionic species strongly interact with polymer chains in the rigid environment, the majority of them reside in the mobile phase and contribute to the overall increased conductivity. Most importantly, Al 2 O 3 nanofibers significantly affect the dynamics of ionic species that are present in the mobile phase between the polymer chains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

As‐Cast Ternary Organic Solar Cells Based on an Asymmetric Side‐Chains Featured Acceptor with Reduced Voltage Loss and 14.0% Efficiency

Abstract A new small‐molecule nonfullerene acceptor based on the benzo[1,2‐ b :4,5‐ b ′]dithiophene (BDT) fused central core with asymmetrical alkoxy and thienyl side chains, namely TOBDT , is designed and synthesized. The alkoxy unit helps narrow the bandgap, and thienyl side chain helps enhance the intermolecular interaction. As a result, TOBDT is suitable to match the deep‐lying highest occupied molecular orbital (HOMO) of polymer donor PM6 . Then, a strong crystalline acceptor IDIC is introduced as the third component to fabricate as‐cast nonfullerene ternary devices to achieve absorption and morphology control. Addition of IDIC not only mixes well with TOBDT but modulates the morphology of the blend film, which helps to balance the charge transport properties and reduce the photovoltage loss of ternary devices. All these contribute to synergetic improvement of J sc , V oc , and fill factor parameters, leading to a power conversion efficiency of 14.0% for the as‐cast fullerene‐free ternary device.

Chen, Xuebin↗
DOE OSTI2022

Identifying the Signatures of Intermolecular Interactions in Blends of PM6 with Y6 and N4 Using Absorption Spectroscopy

Abstract In organic solar cells, the resulting device efficiency depends strongly on the local morphology and intermolecular interactions of the blend film. Optical spectroscopy was used to identify the spectral signatures of interacting chromophores in blend films of the donor polymer PM6 with two state‐of‐the‐art nonfullerene acceptors, Y6 and N4, which differ merely in the branching point of the side chain. From temperature‐dependent absorption and luminescence spectroscopy in solution, it is inferred that both acceptor materials form two types of aggregates that differ in their interaction energy. Y6 forms an aggregate with a predominant J‐type character in solution, while for N4 molecules the interaction is predominantly in a H‐like manner in solution and freshly spin‐cast film, yet the molecules reorient with respect to each other with time or thermal annealing to adopt a more J‐type interaction. The different aggregation behavior of the acceptor materials is also reflected in the blend films and accounts for the different solar cell efficiencies reported with the two blends.

Kroh, Daniel↗
DOE OSTI2021

Polymorphism and Optoelectronic Properties in Crystalline Supramolecular Polymers

Supramolecular polymers can emulate some of the physical properties of covalent polymers but offer new opportunities given the possibility of designing monomers that will form highly ordered assemblies with defined shapes. Internally ordered supramolecular polymers formed through nucleation–elongation self-assembly are well-known but highly crystalline examples which exhibit important properties such as light harvesting, charge transport, and ferroelectricity are not common. We report here on a detailed study of supramolecular polymers formed in water by carboxylated naphtho-p-quinodimethane amphiphiles. We found that supramolecular polymerization of these amphiphiles in aqueous media yields crystalline assemblies with morphologies that included ribbons, helically rolled ribbons, and twisted filaments. This polymorphism was found to be controlled exclusively by repulsive electrostatic interactions controlled by the degree of protonation of the carboxylic head groups which also dictates the nature of supramolecular packing. Substoichiometric amounts of base lead to highly crystalline ribbons due to a decreased surface charge density and less electrostatic repulsion. Increasing deprotonation results in helically rolled ribbons with a different polymorph crystal lattice, whereas excessive deprotonation leads to twisted filaments with maximum surface charge density. Ribbons, helical rolled ribbons, and twisted filaments revealed an increasing red shift in their visible absorption maxima. These crystalline assemblies could be potential candidates for solar energy materials and photocatalytic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Melt State Reinforcement of Polyisoprene by Silica Nanoparticles Grafted with Polyisoprene

Here, we systematically vary the nanoparticle (NP) dispersion state in composites formed by mixing polyisoprene homopolymers with polyisoprene grafted silica particles, and demonstrate how creep measurements allow us to overcome the limitations of small amplitude oscillatory shear (SAOS) experiments. This allows us to access nearly 13 orders in time in the mechanical response of the resulting composites. We find that a specific NP morphology, a percolating particle network achieved at intermediate graft densities, significantly reinforces the system and has a lower NP percolation loading threshold relative to other morphologies. These important effects of morphology only become apparent when we combine creep measurements with SAOS re-emphasizing the role of synergistically combining methods to access the mechanical properties of polymer nanocomposites over broad frequency ranges.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Electrospun Nanofiber Electrodes for High and Low Humidity PEMFC Operation

MEAs with nanofiber mat electrodes containing Pt/C catalyst and Nafion binder were fabricated and evaluated. The electrodes were prepared by electrospinning a solution of catalyst powder, salt-form Nafion (with Na + , Li + , or Cs + as the sulfonic acid counterion), and a carrier polymer of either polyethylene oxide or poly(acrylic acid). The carrier polymer was extracted prior to MEA testing by a hot water soaking step. The resulting fibers were 15%–17% porous, with a core–shell-like morphology (a coating of primarily Nafion on the fiber surface). MEAs with anode/cathode catalyst loadings of 0.1 mg Pt cm −2 each and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions in H 2 /air fuel cell tests, e.g., a maximum power density of 919 mW cm −2 at 100% RH and 832 mW cm −2 at 40% RH for a test at 80 °C and 200 kPa abs . The presence of nm-size pores within the fibers trapped water via capillary condensation during low RH feed gas testing, thus maintaining a high proton conductivity of the Nafion binder in the anode and cathode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder.

25 ENERGY STORAGE↗
DOE OSTI2025

Minimizing Energy Loss by Designing Multifunctional Solid Additives to Independent Regulation of Donor and Acceptor Layers for Efficient LBL Polymer Solar Cells

Solid additives are crucial in layer-by-layer (LBL) polymer solar cells (PSCs). Despite its importance, the simultaneous application of solid additives into both donor and acceptor layers has been largely overlooked. In this work, two multifunctional solid additives are actively designed, and investigated the synergistic effect on both donor and acceptor layers. Incorporating the multifunctional solid additives into the donor layer could effectively enhance the aggregation and molecular stacking of the donor polymer, leading to reduced energy disorder and minimizing ΔE 2 . When the multifunctional solid additives are introduced into the acceptor layer, they just play a role in optimizing the morphology, thereby reducing the ΔE 3 . Excitedly, the simultaneous addition of the multifunctional solid additives into both donor and acceptor layers produced a synergistic effect for decreasing ΔE 2 and ΔE 3 simultaneously, especially adding SA2, thus enabling an excellent power conversion efficiency (PCE) of 19.95% (certified as 19.68%) with an open-circuit voltage (V oc ) of 0.921 V, a short circuit current density (J sc ) of 27.08 mA cm -2 and a fill factor (FF) of 79.98%. The work highlights the potential of multifunctional solid additives in independently regulating the properties of donor and acceptor layers, which is expected as a promising approach for further developing higher performance PSCs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Layer-by-Layer Organic Solar Cells Enabled by 1,3,4-Selenadiazole-Containing Crystalline Small Molecule with Double-Fibril Network Morphology

A double-fibril network of the photoactive layer morphology is recognized as an ideal structure facilitating exciton diffusion and charge carrier transport for high-performance organic solar cells (OSCs). However, in the layer-by-layer processed OSCs (LbL-OSCs), polymer donors and small molecule acceptors (SMAs) are separately deposited, and it is challenging to realize a fibril network of pure SMAs with the absence of tight interchain entanglement as polymers. Here, in this work, crystalline small molecule donors (SMDs), named TDZ-3TR and SeDZ-3TR, were designed and introduced into the L8-BO acceptor solution, forcing the phase separation and molecular fibrilization. SeDZ-3TR showed higher crystallinity and lower miscibility with L8-BO acceptor than TDZ-3TR, enabling more driving force to favor the phase separation and better molecular fibrilization of L8-BO. On the other hand, two donor polymers of PM6 and D18 with different fibril widths and lengths were put together to optimize the fibril network of the donor layer. The simultaneously optimization of the acceptor and donor layers resulted in a more ideal double-fibril network of the photoactive layer and an impressive power conversion efficiency (PCE) of 19.38 % in LbL-OSCs.

36 MATERIALS SCIENCE↗
NASA NTRS2010

Formation, Structure and Properties of Amorphous Carbon Char from Polymer Materials in Extreme Atmospheric Reentry Environments

Amorphous carbonaceous char produced from the pyrolysis of polymer solids has many desirable properties for ablative heat shields for space vehicles. Molecular dynamics simulations are presented to study the transformation of the local atomic structure from virgin polymer to a dense, disordered char [1]. Release of polymer hydrogen is found to be critical to allow the system to collapse into a highly coordinated char structure. Mechanisms of the char formation process and the morphology of the resulting structures are elucidated. Thermal conductivity and mechanical response of the resulting char are evaluated [2]. During reenty, the optical response and oxidative reactivity of char are also important properties. Results of ab initio computations of char optical functions [3] and char reactivity [4] are also presented.

Lawson, John W.↗
DOE OSTI2022

Efficient and mechanically-robust organic solar cells based on vertical stratification modulation through sequential blade-coating

Mechanically durable organic solar cells (OSCs) with high efficiency are deemed as the ideal candidate for the power source of the next generation wearable electronic devices. However, the brittle nature of small molecules in most high-efficiency OSCs consisting of polymer and small molecule encourages easy formation of cracks in the photoactive film under deformation. Here, the vertical composition distribution of the active layer has been well optimized through sequential blade coating to realize highly deformable while efficient OSC. The optimized morphology exhibits distinct donor-rich and homogenous region distributed along the vertical direction in the bulk. The donor-rich region provides sufficient chain entanglements and strong interfaces beneficial for mechanical robustness of film, while homogeneously mixed region offers continuous interpenetrating network to maintain high device through-put, resulting in superior efficiency of 14.4% with high crack-onset strain (COS) of 30.5%. This efficiency versus COS combination is much higher than the best combination reported in all polymer systems (COS of 15.9% and efficiency of 11.1%). To the best of our knowledge, it is the highest COS value achieved in polymer-small molecule systems. As a result, the rational control over vertical stratification demonstrated here would guide researchers in the development of innovative wearable electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermo-mechanical deterioration and molecular degradation of 3D-printed methacrylate-based polymer in various chemical environments

The advancement of additive manufacturing (AM) has accelerated the development of stereolithographic (SLA) photo-curable resins, particularly methacrylate-based polymers, due to the ability to their high-resolution, robust mechanical properties, and suitability. However, their long-term performance in chemical environments remains poorly understood. This study investigates the extent and mechanisms of degradation on an SLA-printed methacrylate-based polymer subjected to various chemicals, including polar and non-polar solvents, as well as strongly acidic aqueous solutions over a 12-week accelerated aging period. A comprehensive analytical approach incorporating swelling kinetics, surface morphology, tensile and dynamic mechanical analysis (DMA), Fourier-transform infrared (FTIR) spectroscopy, and mass spectrometry (MS) was employed to characterize chemical absorption, structural integrity, and leached products. Results reveal that degradation severity is governed by both the polarity and reactivity of the chemical environment. Notably, exposure to 6 mol L -1 HNO₃ induced the most severe deterioration, with over threefold higher swelling compared to other media, and significant reductions in tensile strength, tensile modulus, and glass transition temperature (T g ). In contrast, specimens aged in non-polar solvents (xylene and dodecane) exhibited negligible chemical interaction and retained mechanical performance. FTIR and MS analyses identified acid-catalyzed hydrolysis of ester groups as prominent degradation pathways in acidic media, while diffusion-controlled plasticization prevailed in polar solvents. Furthermore, this study provides valuable insights into the chemical stability of SLA-printed polymers and develops predictive degradation profiles that are crucial for designing durable polymer systems for advanced industrial use.

36 MATERIALS SCIENCE↗
NASA NTRS2022

Building and Breaking Carbon Composites with REACTER

Carbon-based composites have become indispensable materials in aerospace and other high-performance applications, yet obtaining a detailed, nanoscale understanding of their morphology and failure mechanisms using only experimental methods remains a difficult challenge. REACTER is a versatile computational modeling tool for atomistic molecular dynamics simulations designed to model chemical reactions at the speed and length scales of classical force fields. In this work, several recent features of REACTER were applied to the creation and subsequent mechanical testing of two classes of carbon composites: carbon nanotube (CNT) composites and carbon fiber reinforced polymers (CFRP). A network of CNTs was grown dynamically using the new ‘create atoms’ feature of REACTER. The CNT filler was embedded into a polyarylacetylene (PAA) matrix by simulated in situ polymerization to obtain the final composite model. To generate the second class of carbon composite, fully carbonized (graphitic) carbon fiber morphologies were created by the method of Desai et al. [1], but using the advanced reaction constraints framework of REACTER. Two fiber models were created, representing a circular carbon fiber core and a flat surface, and similarly infiltrated with resin to obtain the final CFRP structure. Failure mechanisms were elucidated by simulating mechanically induced bond breaking, as characterized by third order DFT-based tight-binding simulations, via a reaction constraint on the total potential energy of the involved atoms.

Polymer↗
DOE OSTI2020

Achieving High Alignment of Conjugated Polymers by Controlled Dip-Coating

Realizing high polymer chain orientation and ordered thin-film microstructures is beneficial for efficient charge transport of conjugated polymers. However, achieving a high alignment degree remains a challenge due to the sensitive nature of polymers to the processing conditions. By simply varying concentrations during a dip-coating method, the component of polymer aggregates that adopt the planar backbones is enlarged and the ensuing assembly process is promoted. Herein, highly oriented polymer thin films of an isoindigo-based conjugated polymer (PII-2T) are prepared to enhance polymer orientation resulting in a drastic booming in carrier mobilities of organic field-effect-transistors (OFETs). The maximum mobility from aligned polymer films increases by up to 8.3 cm 2 V -1 s -1 , which is tenfold beyond the value evaluated from the unaligned direction or traditional spin-coated samples. The enhanced orientation can also reduce the adverse effects of the contact resistance and facilitate charge transport in transistors. This work demonstrates that the highly aligned conjugated polymer films can be approached by the dip-coating method while offers a latent cornerstone toward understanding the critical role of processing-related parameters in determining morphology of solution-coated thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Simultaneous Improvements in Efficiency and Stability of Organic Solar Cells via a Symmetric‐Asymmetric Dual‐Acceptor Strategy

Abstract Simultaneously achieving improvements in power conversion efficiency (PCE) and stability is the main task of the current development stage of organic solar cells (OSCs). This work reports a symmetry–asymmetry dual‐acceptor (SADA) strategy to construct ternary devices, which is found to be feasible for increasing both the PCE and the operational lifetime of OSCs. In this contribution, the symmetric acceptor L8‐BO and the asymmetric acceptor BTP‐S9 are blended in equal proportions with polymer donor PM6 for the consideration of absorption spectrum complementarity and cascade energetic alignment. In addition, the features of crystallinity and miscibility of the dual‐acceptor deliver optimized morphology lead to a high PCE of 18.84%. In addition, the asymmetric acceptor BTP‐S9 with a larger dipole moment shows tighter molecular stacking and longer crystal correlation length, which favor intrinsic molecular photostability, and further consolidate the operational lifetime of OSCs when coordinated with L8‐BO. This work demonstrates the efficacy of the SADA strategy for constructing efficient and stable OSCs.

Chemistry↗