Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Plasma devices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Observations of the plasma torus of Jupiter with a Fabry-Perot/charge-coupled device /CCD/ imaging spectrometer

A description is presented of the use of a CCD imaging spectrometer which has been employed at a 2.1 m telescope to obtain monochromatic images in the red and near infrared. The system studied was Jupiter's plasma torus which circles the planet with radial extent about 5 RJ and 7 RJ (RJ is the radius of Jupiter). In ground based measurements the torus has been observed in the forbidden emission lines of S(plus) at 6716 A and 6731 A and S(plus plus) at 9531 A. Attention is given to aspects of instrumentation, observations, and performance. It is felt that the particular significance of the obtained results from the instrumental point of view is the demonstration that the CCD is an excellent detector for monochromatic imaging in the near infrared out to at least 10830 A and that pixel binning before readout can produce significantly improved S/N ratios for the study of faint, diffuse sources in cases where readout noise is dominant.

Roesler, F. L.↗
DOE OSTI2026

Edge fluctuation measurements in EDA H-mode and QCE plasmas in ASDEX Upgrade using the correlation electron cyclotron emission diagnostic

The requirement of a plasma solution without large edge-localized modes (ELMs) for future fusion devices motivates the study of plasmas without Type I ELMs. The enhanced D–α (EDA) and quasi-continuous exhaust (QCE) scenarios are two such Type I ELM free plasmas, but their underlying physics principles are not fully understood. A database of EDA and QCE plasmas from ASDEX Upgrade was compiled and analyzed using the correlation electron cyclotron emission diagnostic in order to study differences between properties of the quasi-coherent mode (QCM) between these two regimes. Investigations into measured spectral properties of the QCM, radiated temperature fluctuations δT rad /T rad , and radial correlation lengths L c showed no differences between the two regimes. Spectral properties using the cross-power spectral density, G xy were similar between regimes, with the values measured to be a central frequency, $f$ $QCM$ ≈ 20 - 50 kHz; spectral width, Δ $f$ ≈ 5 - 40 kHz; δT rad /T rad ≈ 4-6%; and L c ≈ 1-2 cm. Investigations into a quantity representing the relative bandwidth Δ$f$/$f$ $QCM$ revealed differences between EDA and QCE plasmas when plotted radially, suggesting some type of interaction between the QCM in QCE plasmas with the surrounding broadband turbulence that is not present in EDA phases. Additionally, investigations into various drive terms for hypothesized instability drivers for the QCM are performed showing no difference in the parameter spaces of collisionality and the ion temperature, electron temperature, or electron pressure scale lengths between each regime indicating that there is no observable difference between the drive behind the QCM in each regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Simulating a pulsed-power-driven plasma with ideal MHD

We describe a simple practical numerical method for simulating plasma driven within a vacuum chamber by a pulsed power generator. Typically, in this type of simulation, the vacuum region adjacent to the plasma is approximated as a highly resistive, light fluid; this involves computationally expensive solvers describing the diffusion of the magnetic field through this fluid. Instead, we provide a recipe for coupling pulsed power generators to the magnetohydrodynamics (MHD) domain by approximating the perfectly insulating vacuum as a light, perfectly conducting, inviscid MHD fluid and discuss the applicability of this counter-intuitive technique. This much more affordable ideal MHD representation is particularly useful in situations where a plasma exhibits interesting three-dimensional phenomena, either due to the design of the experiment or due to developing instabilities. We verified that this coupling recipe works by modeling an exactly solvable flux compression generator as well as a self-similar Noh-like solution and demonstrated convergence to the theoretical solution. We also showed examples of simulating complex three-dimensional pulsed power devices with this technique. We release our code implementation to the public.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

The high-field tokamak physics basis for the ARC fusion power plant

This editorial summarizes the physics basis underlying the ARC high-field tokamak fusion power plant, including recent advances in tokamak plasma understanding, the role of the SPARC device, and key remaining physics questions. It describes how these results guide the ARC Version 3A design and outlines opportunities for the broader fusion community to contribute to the development of first-generation fusion power plants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2002

2-D Magnetohydrodynamic Modeling of A Pulsed Plasma Thruster

Experiments are being performed on the NASA Marshall Space Flight Center (MSFC) MK-1 pulsed plasma thruster. Data produced from the experiments provide an opportunity to further understand the plasma dynamics in these thrusters via detailed computational modeling. The detailed and accurate understanding of the plasma dynamics in these devices holds the key towards extending their capabilities in a number of applications, including their applications as high power (greater than 1 MW) thrusters, and their use for producing high-velocity, uniform plasma jets for experimental purposes. For this study, the 2-D MHD modeling code, MACH2, is used to provide detailed interpretation of the experimental data. At the same time, a 0-D physics model of the plasma initial phase is developed to guide our 2-D modeling studies.

Thio, Y. C. Francis↗
NASA NTRS2002

An Experimental Study of a Pulsed Electromagnetic Plasma Accelerator

Experiments are being performed on the NASA Marshall Space Flight Center (MSFC) pulsed electromagnetic plasma accelerator (PEPA-0). Data produced from the experiments provide an opportunity to further understand the plasma dynamics in these thrusters via detailed computational modeling. The detailed and accurate understanding of the plasma dynamics in these devices holds the key towards extending their capabilities in a number of applications, including their applications as high power (greater than 1 MW) thrusters, and their use for producing high-velocity, uniform plasma jets for experimental purposes. For this study, the 2-D MHD modeling code, MACH2, is used to provide detailed interpretation of the experimental data. At the same time, a 0-D physics model of the plasma initial phase is developed to guide our 2-D modeling studies.

Thio, Y. C. Francis↗
DOE OSTI2023

Implementation of extreme ultraviolet spectroscopy on a sheared-flow-stabilized Z pinch

A diagnostic for extreme ultraviolet spectroscopy was fielded on the sheared-flow-stabilized (SFS) fusion Z-pinch experiment (FuZE-Q) for the first time. The spectrometer collected time-gated plasma emission spectra in the 5–40 nm wavelength (30–250 eV) range for impurity identification, radiative power studies, and for plasma temperature and density measurements. The unique implementation of the diagnostic included fast (10 ns risetime) pulsed high voltage electronics and a multi-stage differential pumping system that allowed the vacuum-coupled spectrometer to collect three independently timed spectra per FuZE-Q shot while also protecting sensitive internal components. Analysis of line emission identifies oxygen (N-, C-, B-, Be-, Li-, and He-like O), peaking in intensity shortly after maximum current (>500 kA). This work provides a foundation for future high energy spectroscopy experiments on SFS Z-pinch devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2020

NASA Next-Generation Sensing Technologies for Earth & Planetary Science

Dr. Ved Chirayath's seminar will highlight new sensing technologies and airborne platforms he is developing for Earth & Space Science as director of the NASA Silicon Valley Laboratory for Advanced Sensing. His talk will feature recent work on Fluid Lensing, the first remote sensing technology capable of imaging through ocean waves in 3D at sub-cm resolutions, MiDAR, a next-generation active hyperspectral remote sensing and optical communications instrument, airborne gas sensing of multipollutant combustion sources, and a plasma actuated unmanned aerial vehicle (UAV) that utilized high-voltage dielectric discharge devices to achieve the first plasma controlled flight in history.Fluid Lensing and the NASA FluidCam instrument have been used extensively to provide distortion-free 3D multispectral imagery from UAVs of shallow marine systems around the world. MiDAR is being deployed on aircraft and underwater remotely operated vehicles (ROVs) as a new method to remotely sense living and nonliving structures in extreme environments as an analog for future Ocean Worlds robotic exploration missions. Finally, Chirayath will present preliminary results from NeMO-Net, a supercomputer-based neural network that uses a citizen science video game for global multimodal coral reef benthic habitat mapping, fusing remote sensing data from Fluid Lensing, MiDAR, NASA's Earth Observing System, and commercial satellites, to better understand the present and past dynamics of shallow marine systems. Together, these maturing technologies present promising new ways in which to explore terrestrial, marine, and aerial systems on Earth, and, ultimately, aid in the search for extraterrestrial life within our solar system and beyond.

Chirayath, Ved↗
DOE OSTI2020

Error field correction strategies in preparation to MAST-U operation

In magnetic fusion devices, unwanted non-axisymmetric magnetic field perturbations, known as error fields (EF), can have detrimental effects on plasma stability and confinement. Such EFs may originate from several sources, such as axi-symmetric coil misalignments, coil feeds, 3D structures in the wall surrounding the plasma, presence of ferromagnetic materials near the plasma surface, blanket materials in future devices. To minimize their impact on plasma performance and on the available operational space, it is important to identify the EF sources and develop EF control strategies. MAST Upgrade (MAST-U) is a spherical tokamak which will operate in the near future after a series of enhancements from the previous MAST experiment. To deliver a machine with EF amplitude low enough to allow a high quality experimental programme, systematic analysis of the intrinsic EF sources has been carried out for poloidal eld (P) and divertor (D) coils. To deliver a machine with EF amplitude low enough to allow a high quality experimental programme, systematic analysis of the intrinsic EF sources has been carried out for poloidal field (P) and divertor (D) coils, whose magnetic eld measurements were available when writing this paper. Such measurements reveal that P and D coils are 3D deformed and thus are responsible for intrinsic EFs, with mainly n=1 and n=2 toroidal mode numbers. In preparation to MAST-U operation, both passive and active EF control strategies have been adopted for n=1 and n=2 EFs compensation. Passive EF control consisted of installing finely each D and P coil within MAST-U device so as to minimize the intrinsic n=1 EF amplitude. The optimal coil alignment has been determined based on magnetic eld measurements and the corresponding 3D electro-magnetic modelling, and envisaged coil shift and tilt of 3.2 mm and 0.7 mrad, respectively, in the case of P coil named P4. Conversely, active control will be use during MAST-U operation to reduce the n=2 EF which is associated mainly with P4 and P5, as well. Since these coils have been re-used from the MAST device, studies attempting n=2 EF control, based on MAST plasmas, have been modelled utilizing the MARS-F code to interpret experimental results in MAST and to give hints for future n=2 EF control studies in MAST-U. Here, a model-based control set for n=2 EF control has been identified which would allow for the minimization of rotation braking, of the resonant magnetic field at the q=2 and of the plasma displacement in MAST-U, simultaneously.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

A next generation ultra short pulse reflectometry (USPR) diagnostic

Ultrashort Pulse Reflectometry (USPR) is a plasma diagnostic technique involving the propagation and reflection of ultrashort duration (~few ns) chirps. The reflected packets pass through a multichannel filter with time-of-flight measurements performed on each of the filtered packets. A next generation USPR system is under development, spanning 28–75 GHz, for use on compact, short duration, magnetically confined fusion devices. This system presents a dramatic increase in performance compared with an earlier USPR system employed on the LLNL Sustained Spheromak Physics Experiment device more than a decade ago. The new system replaces upconverting mixers with higher power active multiplier chains to generate mm-wave transmitter chirps, with custom time-of-flight electronics reducing the time per measurement by a factor of 3X. Finally, the system is equipped with a field programmable gate array for data acquisition and analysis.

47 OTHER INSTRUMENTATION↗
NASA NTRS2006

Magnetic Nozzle and Plasma Detachment Experiment

High power plasma propulsion can move large payloads for orbit transfer (such as the ISS), lunar missions, and beyond with large savings in fuel consumption owing to the high specific impulse. At high power, lifetime of the thruster becomes an issue. Electrodeless devices with magnetically guided plasma offer the advantage of long life since magnetic fields confine the plasma radially and keep it from impacting the material surfaces. For decades, concerns have been raised about the plasma remaining attached to the magnetic field and returning to the vehicle along the closed magnetic field lines. Recent analysis suggests that this may not be an issue of the magnetic field is properly shaped in the nozzle region and the plasma has sufficient energy density to stretch the magnetic field downstream. An experiment was performed to test the theory regarding the Magneto-hydrodynamic (MHD) detachment scenario. Data from this experiment will be presented. The Variable Specific Impulse Magnetoplasma Rocket (VASIMR) being developed by the Ad Astra Rocket Company uses a magnetic nozzle as described above. The VASIMR is also a leading candidate for exploiting an electric propulsion test platform being considered for the ISS.

Chavers, Gregory↗
DOE OSTI2025

Capability in Theory, Modeling, and Validation for a Range of Innovative Fusion Concepts using High-Fidelity Moment-Kinetic Models

A computational modeling capability is created and available to the fusion community to understand and design lower-cost and innovative fusion concepts. The approach uses high- fidelity kinetic, moment-kinetic, and moment models and includes sophisticated plasma- boundary interactions. A majority of fusion-relevant simulations are performed with magnetohydrodynamic models and hybrid particle-in-cell codes, with limited-fidelity electron and kinetic physics. However, in fusion configurations like Z-pinches, field-reversed- configurations, plasma jet magneto-inertial fusion, spinning mirrors, and others, kinetic effects (both electron and ions) are critical to understand the physics and design scaling into the highly kinetic regime of a burning fusion plasma. Furthermore, as present fusion machines move towards a burning plasma regime, liquid-metal blankets are needed to handle first-wall heat- flux, reduce erosion, and eventually for energy conversion and fuel breeding. The work performed under this ARPA-E BETHE Capability Team advances the state-of-the-art in modeling and understanding plasma dynamics in fusion devices and its coupling with liquid-metal dynamics. These are critical areas of research for fusion energy to become realizable. To address these complex problems, we have leveraged and extended computational capabilities through the code, Gkeyll (developed jointly with Princeton Plasma Physics Laboratory and academic partners), for kinetic and moment modeling of fusion plasmas. The Concept Teams supported by this Capability Team include the Wisconsin High-field Axisymmetric Mirror (WHAM), Centrifugal Mirror Experiment (CFME), Plasma-Jet Magneto- Inertial Fusion (PJMIF), and solid and liquid wall plasma-material interaction studies relevant to a number of fusion concepts including Zap Energy’s Z-pinch. This software is open-source and available to the fusion community as a high-fidelity tool for the design of lower-cost fusion experiments. 3D gyrokinetic simulations of WHAM are now possible for long enough time scales to understand the evolution of interchange instabilities. 3D multi-fluid simulations of CMFE at higher Mach numbers are now possible for detailed design iterations with the goal of stability. The state-of-the-art in understanding shock formation and shock mitigation regimes in merging liners for PJMIF have been furthered by our kinetic simulations. Our novel models and frameworks studying plasma-material interaction by incorporating wall emission for various solid wall materials of relevance to pulsed and steady fusion concepts have advanced the state-of-the-art in our understanding of particle fluxes, heat fluxes, and other quantities at cathodes and anodes. The results from this work may explain discrepancies between experimental and theoretical predictions of achieved current densities in pulsed concepts such as Z-pinches. Another significant contribution of this Capability Team is the development and deployment of a novel experimental platform, LEX (Liquid Electrode eXperiment), at Virginia Tech to understand liquid metal free-surface response to electromagnetic pulses. The novel experiments along with model validation quantified the effect of different materials and sizes of liquid metal droplets on the radiative power balance of fusion plasmas for pulsed concepts. Furthermore, these experiments provided mitigation strategies for violent liquid metal response for high current pulses as would be expected in fusion regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2018

Hollow Cathode Thermal Modelling and Self-Consistent Plasma Solution: Work Function Evaluation for a LaB6 Cathode.

Self-heating hollow cathodes are central components in modern electric thrusters. The plasma discharge inside these devices heats the internal components, thus maintaining the temperatures required for electron emission. Precise knowledge of the physical phenomena governing hollow cathode operation is key to predict their lifetime, specifically, their thermionic emission characteristics. A simulation platform has been built to couple plasma and thermal models of the self-heating hollow cathode to produce a self-consistent solution. A self-consistent solution has been found for a LaB6 hollow cathode operating at 25A and 13 sccm where the work function is assumed to be spatially uniform along the emitter with a value which is allowed to vary as the coupled model iterates to a self-consistent solution. The emitter temperature from the converged solution does not agree with experimental temperature measurements, however. The results of a sensitivity analysis suggest that none of the tolerances in the measurement are responsible for the discrepancy. We hypothesize that either the work function needs to be a function of position along the emitting surfaces or the heat fluxes have been overestimated in the plasma solver.

Meiron, Daniel I.↗
DOE OSTI2024

MCTrans++: a 0-D model for centrifugal mirrors

The centrifugal mirror confinement scheme incorporates supersonic rotation of a plasma into a magnetic mirror device. This concept has been shown experimentally to drastically decrease parallel losses and increase plasma stability as compared with prior axisymmetric mirrors. MCTrans++ is a dimensionless (0-D) scoping tool which rapidly models experimental operating points in the Centrifugal Mirror Fusion Experiment (CMFX) at the University of Maryland. In the low-collisionality regime, parallel losses can be modelled analytically. A confining potential is set up that is partially ambipolar and partially centrifugal. Due to the stabilizing effects of flow shear, the perpendicular losses can be modelled as classical. Radiation losses such as bremsstrahlung and cyclotron emission are taken into account. A neutrals model is included, and, in some circumstances, charge-exchange losses are found to exceed all other loss mechanisms. We use the SUNDIALS ARKODE library to solve the underlying equations of this model; the resulting software is suitable for scanning large parameter spaces, and can also be used to model time-dependent phenomena such as a capacitive discharge. MCTrans++ has been used to verify results from prior centrifugal mirrors, create an experimental plan for CMFX and find configurations for future reactor-scale fusion devices.

Schwartz, Nick R. (ORCID:0000000296846435)↗
DOE OSTI2022

Experimental study on boron distribution and transport at plasma-facing components during impurity powder dropping in the Large Helical Device

Toward real-time wall conditioning, impurity powder dropping experiments with boron powder were performed in the 22nd experimental campaign of the Large Helical Device. To examine the deposition and desorption process of boron, we focus on boron hydride (BH) molecules which presumably populate near plasma-facing components. We performed spatially-resolved spectroscopic measurements of emission by boron ions and BH molecules. From the measurement, we found that BH and B + were concentrated on the divertor viewing chord, which suggest boron deposition in the divertor region. By comparing Hγ emissions with and without boron injection, neutral hydrogen shows uniform reduction in the SOL region, whereas less reduction of neutral hydrogen is confirmed in the divertor region. Although emissions from BH and B + increased linearly, emissions by B0 and B4 + became constant after the middle of the discharge. Continuous reduction of carbon density in the core plasma was confirmed even after B 0 and B 4 + became constant. The results may show reduction of hydrogen recycling and facilitation of impurity gettering by boron in the divertor region and thus effective real-time wall conditioning.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Alfvén eigenmode stability in a JET afterglow deuterium plasma and projections to deuterium–tritium plasmas

Abstract The performance of fusion devices relies strongly on the good confinement of energetic particles (EPs). Therefore, the investigation of EP transport by magnetohydrodynamic instabilities is one of the key aspects in the development of plasma scenarios. Alfvénic instabilities in particular can lead to significant losses of alpha particles that are essential for plasma self-heating. A so-called afterglow scheme has been developed to study the destabilization of Alfvén eigenmodes (AEs) by alpha particles and associated EP transport in the JET tokamak. In this work, the linear stability of AEs is discussed for the partial afterglow phase in a JET deuterium plasma discharge and for the full afterglow phase in a projected deuterium–tritium (DT) plasma. Thanks to recent upgrades in the tokamak transport code TRANSP, one can account for the contributions of different EP species to mode stability. Analysis of deuterium plasmas shows that AE growth rates are extremely sensitive to the energy and distribution of fast ions. An increase in fast ion energy can lead to more unstable AEs. In the afterglow phase of projected DT plasmas, it is EPs that mostly drive the AEs. However, the drive by alpha particles is comparable to that by beam ions and their contribution to the net growth rate might be hard to separate. According to the discussed projections, the destabilization of AEs might be ineffective because the background plasma damping significantly exceeds the EP drive. In this case, the development of an alternative plasma scenario that allows us to overcome such damping would be required in future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗