Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PHYSICS LABORATORY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

X-Ray Photoelectron Spectroscopy

The interaction of photon and the electron goes back to the early part of 19th century emanating from the photo-electric effect depicted by none other than Albert Einstein (Ref 1) described in 1905, and the redistribution of kinetic energy resulting from the interaction of x-ray and solids reported during early part of the century (Ref.2). The spectrum resolutions obtained at that time was not sufficient to observe distinct peaks in spectra for materials. Thus, these phenomena hardly attracted any attention for many years following these discoveries. The modern X-ray Photoelectron Spectroscopy (XPS) has been possible by the extensive and significant contribution from Kai Siegbahn and others (Ref.3, 4) of Uppsala University. Siegbahn developed and employed a high-resolution electron spectrometer that revealed electron peaks in a spectrum emerging from the interaction of x-rays and solids. Eventually, Kai Siegbahn received Nobel Prize in 1981 for his contributions to XPS. Around 1958, shifts in elemental peaks were realized in compounds when the same elements are bound to other but different elements. This discovery resulted in the chemical state identification in various chemicals as well as the oxidation states of atoms in compounds. Because of these useful physical effects, the Uppsala group named XPS with a synonymous name of ESCA (Electron Spectroscopy for Chemical Analysis) used widely today and will be used here alternatively. Therefore, XPS or ESCA not only identifies the element, but also the compound these elements form, from their chemical shifts. Compared to other micro-analytical techniques such as Energy Dispersive (EDS) or Wavelength Dispersive (WDS) techniques, XPS analyzes only few atomic layers present on the surface. This was discovered early in 1966 (Ref. 5). While this has awarded a merit to the analytical technique to analyze very thin layers such as films and coatings, it often analyzes the adsorbed superficial gases and contaminations on a sample introduced to its analytical chamber. This necessitates the surface is cleaned and the underlying material, material of interest, is exposed in a clean environment such that the material of interest is analyzed. The cleaning is accomplished by a scanning ion gun within the analytical chamber of the instrument. Ion gun uses an argon gas and is commonly attached in most modern machines. Reliable and efficient vacuum systems employed in modern machines does not allow adsorbed layers to rebuild after the surface is cleaned. Development of efficient and reliable vacuum pumps over these developmental years is yet another important step in the commercialization of XPS machines. Vacuum levels of better than 10-7 torr are essential to increase the mean free path of electrons released from the sample surface. Thus, modern machines are equipped with high capacity ion, turbo or cryogenic pumps in their analytical chambers. Today, XPS has advanced from an applied physics laboratory to industry for use in quality control as well as analysis of contaminants and has taken a dominant role in microanalysis. Its uniqueness arises from the fact that it is considered non-destructive compared to other common micro-analytical techniques using the electron and ion excitation sources. Polymers and plastics could be analyzed since the binding energies of saturated and unsaturated bonds in atoms could be separated. Extremely thin layers could be analyzed including materials with layered structures. The technique, though did not advance for many years, has now opened a new window for research as well as applications in industry due to its ability to separate and measure the chemical shifts in bound elements. Principles

Panda, Binayak↗

Fusion-Enabled Pluto Orbiter and Lander

Direct Fusion Drive (DFD) is a unique fusion engine concept based on the Princeton Field-Reversed Configuration (PFRC) fusion reactor conceived by Dr. Sam Cohen of the Princeton Plasma Physics Laboratory. DFD would enable the Pluto orbiter and lander context mission and more broadly enable true "rapid transit" to outer-planet and near interstellar space. The truly game-changing levels of thrust and power in a modestly sized package could integrate with our current launch infrastructure while radically expanding the science capability of these missions. Our Phase I was our first funded work on the DFD, with previous work at PSS occurring only under internal R&D. We established the feasibility of our Pluto mission trajectories using straight-line and planar models, including a departure spiral from Earth and insertion at Pluto. We developed our first thrust and specific impulse model using the results of the UEDGE multi-fluid code. Our specific power model was improved. During this Phase II effort, we continued our efforts to increase the fidelity of the designs for the RF, magnet, and shielding subsystems. Dedicated thrust augmentation experiments were run on the PFRC experiment, using a supersonic gas puffing valve. For the first time, we analyzed the design of a closed-loop operation mode and estimated the hardware that would be required for a dual-mode engine. In an exciting new development, we have invented a new thermophotovoltaic thermal conversion method that has the potential to have efficiencies of a Brayton or Stirling system. Our report presents details of these analyses. Our roadmap to bringing DFD to flight predicts that with sufficient support, a first flight unit could be built by 2040. We anticipate that three machine generations are required before this point: a ~1 T PFRC-3 machine hitting new plasma temperature and density levels, a ~5 T PFRC-4 machine with first demonstration of D-3He fusion, and a flight. (The current experiment, PFRC-2, is limited to about 0.1 T). In order to achieve a flight in 2035-2040, the TRL of the supporting systems must be increased in parallel, including low mass radiators, cryogenic propellant storage, and large (>100 kW) thermal conversion systems. Fortunately, many of these systems are dual-use and are required for other technologies including fission systems, so DFD would contribute to and benefit from those programs. This NIAC support and the results of our work have led to multiple follow-on contracts. We won two NASA STTRs focused on DFD subsystems, one on the RF system and one on the superconducting magnets, and our magnet STTR is now midway through a Phase II. We will be receiving a superconducting test magnet for experiments at PPPL this summer. In addition, we won an ARPA-E OPEN grant; this is the first time that OPEN has included fusion technologies, and we are part of a cohort of three alternative fusion companies now supported directly by DOE. We are very optimistic that if we are able to meet our experimental milestones in the next 12-18 months, we will be competitive for additional DOE grants to build PFRC-3.

Propulsion↗

Current State of the Electrodynamic Dust Shield for Mitigation

The Electrodynamic Dust Shield (EDS) has been developed as a means to lift, transport and remove dust from surfaces for over 18 years in the Electrostatics and Surface Physics Laboratory at NASA Kennedy Space Center. Resent advances in the technology have allowed large-scale EDSs to be fabricated using roll-to-roll techniques for quick efficient processing. The aim of the current research is to demonstrate the 3-dimensional (3-D) version of the EDS and its applicability to various surfaces of interest throughout the Artemis program that require dust mitigation. The conventional two dimensional (2-D) EDS has been comprised of interdigitated electrodes across a surface of alternating polarity to setup non-uniform electric fields in the location of interest for which the particles need to be removed. The 2-D system can be designed to accommodate various phases. For example, the two phase EDS is comprised of two electrodes 180˚ out of phase, while the 3-phase EDS is 120˚ out of phase with the adjacent leg. 4-phase EDS configurations are also possible but for each square wave a high voltage signal is applied to each leg.

Buhler, C. R.↗

Space Launch System Payload Stage Capability for Ultra-High Characteristic Energy Missions

The Space Launch System (SLS) vehicle is NASA’s cornerstone capability for a new era of human and robotic exploration of deep space. The unrivalled performance of SLS provides the capability to launch the first woman and next man to walk on the lunar surface and to support development of a sustained human presence in cislunar space, and ultimately human missions to Mars. As an evolvable capability with unique launch performance, the opportunities enabled by SLS also include game-changing benefits for science missions, including probes to the outer solar system and beyond. For the last two years, the SLS Program has worked with the Interstellar Probe team at the Johns Hopkins University Applied Physics Laboratory(APL) to provide data that describe how SLS could support a mission that would break through the boundary of the heliosphere and into pristine interstellar space only a decade after launch, enabling earlier science return and greatly increasing spacecraft life in the interstellar medium. In record-breaking time, the ISP as launched on SLS may answer questions raised by the extended mission of NASA’s Voyager spacecraft. While SLS and its efficient Exploration Upper Stage (EUS) offer benefits for exploration of the outer planets, adding one or more additional stages to this architecture makes it even more capable for missions beyond our solar system, offering more realistically appealing flight times that would allow the mission scientists to reap the rewards of exploration. During the time the SLS Program has been working with the Interstellar Probe team, it has identified an expedited path to the Block 2 capability planned for the Interstellar Probe mission, and further matured performance numbers for diverse multi-stage configurations using a combination of commercially available liquid hydrogen (LH2)/liquid oxygen (LOX) upper stages and solid motor kick stages. That work has demonstrated the SLS payload stage capability provides significant benefits and opens trade space for multiple missions in consideration during planning for the next Planetary Science and Astrobiology Decadal Survey. This presentation details the significant benefits SLS can provides for very high characteristic (C3) energy missions by coupling the capabilities of SLS to current commercial rocket propulsion stage systems. These capabilities are explored specifically in the context of an Interstellar Probe architecture in which a small, capable science probe, coupled with carefully tailored mission design trajectories, could be used to explore the outer solar system and the interstellar medium. The presentation will also address the operational logistics of integrating such a mission, explaining the options available for “non-standard” SLS payloads, including processing those with radioisotope power generators or additional propulsion stages. An SLS system overview and capabilities will be presented, along with vehicle configuration and orbit performance capability studies, explaining how SLS is enabling for a variety of high-energy science mission profiles, including launching an exploratory probe bound for interstellar space only a decade after launch.

Rob Stough↗

NASA Access 2 Space Workshop: Summary Report: Increased Science Return through Rideshare

This report summarizes the Access to Space (A2S) Workshop held on February 25-27, 2020 at the Johns Hopkins University Applied Physics Laboratory (APL) and hosted by NASA’s Science Mission Directorate (SMD). This workshop solicited community input on the creation and management of an ESPA-class1payload pipeline for NASA SMD launches. The workshop brought together roughly 180 participants including scientists, engineers, instrument developers, launch providers, and policy makers across NASA centers, government agencies, commercial industry, research institutes, and academia.

ESPA-Class Spacecraft↗

Mercury Lander: Transformative Science from the Surface of the Innermost Planet

As an end-member of terrestrial planet formation, Mercury holds unique clues about the original distribution of elements in the earliest stages of solar system development and how planets and exoplanets form and evolve in close proximity to their host stars. This Mercury Lander mission concept enables in situ surface measurements that address several fundamental science questions raised by MESSENGER’s pioneering exploration of Mercury. Such measurements are needed to understand Mercury’s unique mineralogy and geochemistry; to characterize the proportionally massive core’s structure; to measure the planet’s active and ancient magnetic fields at the surface; to investigate the processes that alter the surface and produce the exosphere; and to provide ground truth for current and future remote datasets. NASA’s Planetary Mission Concept Studies (PMCS) program awarded this study to a multidisciplinary team led by Dr. Carolyn Ernst of the Johns Hopkins Applied Physics Laboratory (APL), to evaluate the feasibility of accomplishing transformative science through a New-Frontiers-class, landed mission to Mercury in the next decade. The resulting mission concept achieves one full Mercury year (~88 Earth days) of surface operations with an ambitious, high-heritage, landed science payload, corresponding well with the New Frontiers mission framework.

Mercury lander↗

Electrodynamic Dust Shield Housing for RASSOR Redesign and Fabrication

Abstract—An Electrodynamic Dust Shield (EDS) was to be mounted over the cameras of the Regolith Advanced Surface Systems Operations Robot (RASSOR) to mitigate the clouding effects and abrasive properties of lunar dust. This report discusses the redesign process and physical fabrication of the housing unit planned to attach the EDS to the RASSOR camera. The two-piece 3D-Printed design consists of a holder and cover unit. The EDS Holder seats the EDS near two live copper contacts that are to be wired into the main electronics housing. The EDS Cover seats two metal leaf spring tabs to bridge the connections between the copper contacts and EDS electrodes, as well as a centralized O-ring that is pressed flush against the EDS to mitigate dust intrusion. All components were modeled, printed, and checked for proper electrical contact and mechanical fit. The built-up assembly was subsequently tested in the Electrostatics and Surface Physics Laboratory (ESPL) and demonstrated good dust clearing performance.

Alexander Lacerna↗

Navigating CONTOUR using the noncoherent transceiver technique

The successful navigation of the Comet Nucleus Tour spacecraft was performed at JPL and was conducted with the use of the new noncoherent transceiver technique developed by the Applied Physics Laboratory. Discussions include the conditioning performed on the 2-way noncoherent Doppler data, the orbit determination process, and the post SRM trajectory reconstruction.

CONTOUR↗

Electrostatic Regolith Interaction Experiment (ERIE) Electrometer Instrument Development

The Electrostatic Regolith Interaction Experiment (ERIE) is a joint venture between the University of Central Florida (UCF) Center for Microgravity Research (CMR) and the NASA Kennedy Space Center (KSC) Electrostatics and Surface Physics Laboratory (ESPL) seeking to examine charged dust grain behavior in a microgravity environment. Two separate systems have been combined for this suborbital flight experiment: the COLLisions Into Dust Experiment (COLLIDE) developed by the UCF CMR and the Wheel Electrostatic Spectrometer (WES) developed by the NASA KSC ESPL. This combination will advance the understanding of the natural and induced charged grain behavior on the Moon, asteroids, and other low gravity bodies comprised of charged dust particles. COLLIDE retains granular material under vacuum in a shallow tray behind a metal door, which then opens and releases the particles into a larger open volume when microgravity is achieved. The experiment is observed with a high-speed camera, such that the motions of these particles can then be tracked so the kinematics of each grain may be analyzed. The original application for this apparatus was to study cratering events into granular beds, but electrostatic repulsion was detected in the early frames of the video data returned from completed experiments, so a re-flight with a focus on these events was proposed. Agitation of the grains during launch combined with the frictional charge transfer between the grains and the door as it slides open provides an opportunity to use this setup to observe material tribocharging and charged particle behaviors in microgravity. In this updated version, the charged particles released into the chamber will traverse through an electric field produced by high voltage parallel plates and their resulting trajectories will be determined by their net charges. WES was originally developed to characterize the triboelectric properties of the Martian regolith through the contact of a rover wheel with the surface as it rotates. Improvements were made upon this legacy system to develop a sensor suite that will be installed within the COLLIDE door to measure charge transferred between the granular material and insulating disks protruding through the door. These insulator disks span the triboelectric series so, as they slide across the particulate matter when the door opens, each will accumulate a charge consistent with its relative position to the grains within the series. This charge on each insulator is distributed between two capacitances in series with an electrometer amplifier returning an analog voltage proportional to the charge accumulated. Calibration of this system has been performed using applications of known charge to the inputs and characterization of the frictional charge transfer between various regolith simulants and the sensor insulators is currently being examined in the lab.

Electrostatics↗

NASA LSII Lunar Simulant Project

Introduction: America has entered a new era of exploration. NASA’s Artemis program will lead humanity forward to the Moon and prepare us for the next giant leap, the exploration of Mars [1]. To champion technologies needed to live on and explore the Moon, NASA’s Space Technology Mission Directorate (STMD) established the Lunar Surface Innovation Initiative (LSII)[2].LSII's technology development portfolio includes: Utilizing the Moon’s resources; Establishing sustainable surface power; Building machinery and electronics that work in extreme environments, like super-chilly permanently shadowed craters; Mitigating lunar dust; Carrying out surface excavation, manufacturing and construction duties; and Extreme access which includes navigating and exploring the surface/subsurface. To support the development and testing of these technologies, LSII created the lunar simulant project, to create and/or acquire low-, medium-and high-fidelity lunar simulants to match the needs of STMD projects at all levels of technology readiness levels (TRL), as well as other NASA programs. There is not one bulk lunar simulant that will satisfy the needs of all projects. NASA's Approach to Simulants: Just as LSII's activities are being implemented through a combination of unique NASA work and public-private partnerships, NASA will work with commercial simulant providers to acquire simulants that meet NASA's needs. If warranted, NASA will develop simulants using government agencies, as was done with the NASA/USGS Lunar Highlands Type (NU-LHT)series of lunar simulants [3].NASA is also collaborating with the Johns Hopkins University Applied Physics Laboratory(JHUAPL) Lunar Surface Innovation Consortium (LSIC) in the development and characterization of lunar simulants [4]. Within NASA, a small team (< 10 people) is coordinating simulant activities across the agency, with team members located at several NASA centers. The overall objective of the project is to procure lunar simulants in sufficient amounts for earth-based testing of subsystems and systems in a variety of environments (i.e., laboratory, high-bay, thermal-vacuum chambers), required for Artemis missions to the Moon, as well as other missions carrying NASA lunar payloads, such as the Commercial Lunar Payload Services (CLPS)program [5]. Lunar Highlands Simulant: NASA's Artemis Program is targeting the lunar south pole region for initial human missions and the Artemis Base Camp. Hence, the LSII lunar simulant project is currently focusing on the mineralogy and properties of lunar highlands regolith [6 and 7]. Plagioclase-rich rocks (e.g., anorthosite, norite) are the dominant constituent in highlands simulants, with Shawmere, Stillwater, and White Mountain anorthosites being used in commercially available simulants. However, because these feedstocks are terrestrial in nature, they include hydrated minerals, carbon-bearing minerals, and other chemical signatures that are not present on the Moon, and these minor mineral assemblages need to be taken into account when trying to understand test procedures and results. Glass Component: While much attention has been placed on the rock/mineral component of lunar simulants, glass is just as important when creating simulants. The glass component in lunar regoliths is often greater than 50% by volume [8]. This component includes impact melt glass, dark matrix breccias, and agglutinates. However, this component is difficult, time-consuming and expensive to make. Most lunar simulants, past and current, have relied on basaltic cinder as a feedstock for glass. Getting better glass components at a lower cost, particularly agglutinates and glass with an anorthositic composition is a near-term objective that the NASA simulant project is trying to address . Characterization: It is extremely important for lunar simulants to be characterized by several analytical methods. Gruener et al. [9] and JHUAPL LSIC [10] conducted initial assessments of some of the commercially available simulants in 2019 and early 2020, before the global pandemic. Further analyses are needed to better quantify important parameters such as, modal mineralogy and glass content, particle shape, and particle size distribution. These quantified results can then be used in determining figures of merit (FOM) that show how well simulants compare to lunar regolith [11 and 12].

J E Gruener↗

Applying the Cognitive Space Gateway to Swarm Topologies

NASA's future vision for interplanetary networking includes a lunar network, Cube Satellite (CubeSat) constellations, and deep space robotic missions, comprising what could be viewed as a network of networks. Delay-tolerant networking (DTN) architecture and protocols provide a standard network layer among these varying scenarios and mitigate many challenges of the space environment, such as long delays, unplanned service interruptions, and asymmetric links. The Cognitive Space Gateway (CSG) is a routing method in a DTN architecture that uses spiking neural networks as the learning element to optimize routing decisions in a complex environment. This work aims to further develop cognitive networking technologies in several critical areas, including DTN, the CSG algorithm, CubeSat swarm topologies, and cloud services. To test the algorithm in a realistic scenario, the emulated network topology is based on a CubeSat swarm. The swarm may function as a mesh of nodes or as a hub-and-spoke network. An emulation environment will be built upon a commercial cloud service, such as Amazon Web Services (AWS) Elastic Compute Cloud. The cloud environment may enable a flexible, lower maintenance approach versus a multi-hop network based in a physical laboratory. The cloud platform will provide a secure environment allowing for collaboration among government and academic entities.

Ricardo Lent↗

Applying the Cognitive Space Gateway to Swarm Topologies

NASA’s future vision for interplanetary networking includes a lunar network, Cube Satellite (CubeSat) constellations, and deep space robotic missions, comprising what could be viewed as a network of networks. Delay-tolerant networking (DTN) architecture and protocols provide a standard network layer among these varying scenarios and mitigate many challenges of the space environment, such as long delays, unplanned service interruptions, and asymmetric links. The Cognitive Space Gateway (CSG) is a routing method in a DTN architecture that uses spiking neural networks as the learning element to optimize outing decisions in a complex environment. This work aims to further develop cognitive networking technologies in several critical areas, including DTN, the CSG algorithm, SmallSat swarm topologies, and cloud services. The CSG algorithm is tested in a realistic scenario in which the emulated network topology is based on a SmallSat swarm. The emulation environment will be built upon a commercial cloud service, such as Amazon Web Services (AWS) Elastic Compute Cloud. This work investigates the ability of such a platform to enable a flexible, lower maintenance approach to creating a multihop network outside of a physical laboratory. The cloud platform will provide a secure environment allowing for collaboration among government and academic entities.

Ricardo Lent↗

Suborbital Lunar Gravity Experiment of an Electrodynamic Regolith Conveyor

NASA’s Swamp Works Electrostatics and Surface Physics Laboratory (ESPL) is planning to test a 4-phase electrodynamic regolith conveyor in simulated lunar gravity on a suborbital flight in 2023. A 4-phase electrodynamic regolith conveyor could convey regolith without the risk of rotating or vibratory actuation, which could jam or require regular maintenance due to the abrasive nature of lunar regolith. Another advantage of electrodynamic conveying is the reduction of conveying power, which is important considering the limited scale of available early-stage lunar power systems. The current state of the art(SOA) for lunar regolith conveying is based on recent NASA system studies for oxygen production plants. These plant designs require conveying rates around 100 kg/hr, to produce 10 mT/yr of oxygen from the regolith. To accomplish this, conventional augers and vibratory spiral conveyors have been identified as the SOA or the leading candidates due to their extensive use in the terrestrial material handling industry. At NASA KSC, the use of dynamic electric fields, generated by alternating high voltage on electrodes, has been developed as a dust mitigation solution known as the Electrodynamic Dust Shield (EDS). The EDS is being developed for lenses, solar panels, radiators, fabric and seals. ESPL researchers have shown the ability to move thin layers (~ a few mm) of dust with mW of power. In Academia, researchers have shown the ability to electrodynamically convey regolith up to ~1 kg/hr with a4-phase EDS and electromagnetically convey particles that would suggest a lunar regolith conveying rate of ~25 kg/hr. This paper will describe the design and expected operation of a 4-phase electrodynamic regolith conveyor in lunar gravity. This paper will also describe how an electrodynamic conveyor could be scaled for transporting ISRU relevant flow rates.

Aaron D S Olson↗

Design and Testing of a Prototype Electrodynamic Regolith Conveyor for Lunar ISRU

NASA’s Swamp Works Electrostatics and Surface Physics Laboratory (ESPL) is developing a 4-phaseelectrodynamic regolith conveyor (ERC) that could convey regolith without the risk of rotating or vibratory actuation, which could jam or require regular maintenance due to the abrasive nature of lunar regolith. Another goal of electrodynamic conveying is the reduction of conveying power, which is important considering the limited capacity of early-stage lunar power systems. The current state of the art(SOA) for lunar regolith conveying is based on recent NASA system studies for oxygen production plants. These plant designs require conveying rates around 100 kg/hr, to produce 10 mT/yr of oxygen from the regolith. To accomplish this, conventional augers and vibratory spiral conveyors have been identified as the SOA or the leading candidates due to their extensive use in the terrestrial material handling industry. At NASA KSC, the use of dynamic electric fields, generated by alternating high voltage on electrodes, has been developed as a dust mitigation solution known as the Electrodynamic Dust Shield (EDS). The EDS is being developed for lenses, solar panels, radiators, fabric and seals and is scheduled for a technology demonstration mission on the Moon in 2023. ESPL researchers have shown the ability to move thin layers (~ a few mm) of dust with mW of power. In Academia, researchers have shown the ability to electrodynamically convey regolith up to ~1 kg/hr with a 4-phase EDS and electromagnetically convey particles that would suggest a lunar regolith conveying rate of ~25 kg/hr. This paper will describe the design and testing of a prototype ERC that could scale to support transporting regolith at ISRU relevant flow rates.

Aaron D S Olson↗

High-Vacuum Triboelectric Charging of Space Materials

In the high-vacuum environment of space and the surface of the moon, static electricity on surfaces lacks the atmospheric dissipation mechanisms found on earth. As a result, the ubiquitous triboelectric charging mechanism can lead to high levels of charge on surfaces. This static charge can result in damage to sensitive devices, interfere with communications, and electrostatic levitation of lunar dust. At the NASA Electrostatics and Surface Physics Laboratory (ESPL), we use different apparatuses and techniques to tribo-charge materials in high-vacuum (10-5 torr), including a tribo-robot and a triboelectric regolith-material stage (TRMS). The tribo-robot is used to rub two materials together, and fieldmeters and electrometers can be used to determine how much charge is on the materials. The TRMS is used to drag different materials onto a bed of lunar simulant. This system is used to characterize how materials may interact with lunar dust using fieldmeters, electrometers, and laser scattering. Using these methods, we are building a database of how different space materials charge when contacting each other at high-vacuum, and how materials triboelectrically interact with the lunar surface.

Joseph Toth↗

EDS to the Moon!

The Electrostatics and Surface Physics Laboratory at NASA Kennedy Space Center is slated to send multiple Electrodynamic Dust Shields (EDS) to the surface of the moon. This paper discusses the EDS onboard a Commercial Lunar Payload System or CLPS mission slated to launch to the moon on July 27, 2023 on Firefly Aerospace’s Blue Ghost Lander to Mare Crisium. The EDS payload consists of a camera EDS, a separate glass EDS, a thermal radiator EDS as well as a Re-Duster system based on EDS technology. The EDS will be deposited on the ground by a deployable structure on the lunar lander shortly after touchdown and its operations will take precedence over the other 10 payloads on the lander. The camera will record images and videos of dust deposition and removal on both the Thermal Radiator EDS and the Glass EDS. Data handling will be done using a Data Storage Unit (DSU) developed by NASA Langley Research Center and downlinked to Earth in real time.

Charles R Buhler↗

The Case for a 50+ Year Radioisotope Power System

The Johns Hopkins University Applied Physics Laboratory (JHU/APL) is leading the NASA funded Interstellar Probe study to explore the “Very Local” interstellar medium. To perform this exploration the mission will be required to last at least 50 years in regions of space where solar power is no longer practical. Additionally, several new studies for the National Academies’ Planetary Science and Astrobiology Decadal Survey are planning missions lasting 20-35 years. The Decadal Survey is used to build consensus on priority of national science goals. These proposed missions are inconsistent with the NASA’s current Radioisotope Power Systems (RPS) life requirement of 14 years (flight). Paramount to these proposed long-duration missions are questions about the longevity of such a mission. Evidence exists that space-borne Radioisotope Power Systems can indeed last a long time. LES-9, Voyager I, and Voyager II are over 40 years old, LES-8, Pioneer 10, and Pioneer 11 lasted 28, 30, and 22 years, respectively, and New Horizons is still active 15 years after launch. This paper explores the need for RPS designs that are intended to last much longer than the current requirement of 14 years (17 years after fueling) and explores the historical record for actual vs design lifetimes to show the feasibility of building long lasting RPS. We also exercise a current RTG performance model of the General-Purpose Heat Source RTG using the JPL Lifetime Performance Prediction (LPP) tool to make top-level inferences about power output at end-of-mission, and discusses how reliability engineering and testing methods can be brought to bear to increase confidence in delivering sufficient power at end-of-mission.

Phan, Brian↗

Dragonfly Entry and Descent Overview

Dragonfly is a New Frontiers class mission led by Johns Hopkins Applied Physics Laboratory (APL) which will deliver a rotorcraft lander to Saturn’s moon Titan [1] for an extended science mission. The spacecraft will launch in 2027 and arrive at Titan in 2033. This presentation will provide an overview of the Entry and Descent system that is under development to ensure the safe delivery of this unique “relocatable lander” to Titan, with an emphasis on some of the key technical challenges that the team is addressing.

Dragonfly↗