Optical Study of the Electronic Structure of Diamond
Diamond electronic structure studied by absolute reflectance measurements, obtaining dielectric response function over broad energy range
DIELECTRIC CONSTANT↗
SEARCH · Engineering Papers
Results for “Optical constants”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A piston-driven shock in the solar corona
A solar flare that occurred on the west limb at 20:38 UT on Mar. 25, 1981 generated a massive, rapidly expanding optical coronal transient, which moved outward with an approximately constant velocity of 800 km/s. An associated magnetohydrodynamic shock traveled out ahead of the transient with a velocity estimated to be approximately 1000 km/s. The optical and radio data on the transient and shock fit well with general theories concerning piston-driven shocks and with current MHD models for propagation of such shocks through the solar corona.
Maxwell, A.↗
Separation of variables solution for non-linear radiative cooling
A separation of variables solution has been obtained for transient radiative cooling of an absorbing-scattering plane layer. The solution applies after an initial transient period required for adjustment of the temperature and scattering source function distributions. The layer emittance, equal to the instantaneous heat loss divided by the fourth power of the instantaneous mean temperature, becomes constant. This emittance is a function of only the optical thickness of the layer and the scattering albedo; its behavior as a function of these quantities is considerably different than for a layer at constant temperature.
Siegel, Robert↗
Thermal motion of the STIS optical bench
Various tests have been done of the Space Telescope Imaging Spectrograph (STIS) using internal wavecals to measure thermal motion of the spectral format on the detectors. In most cases, the spectral format moves less than the specification not to exceed 0.2 pixels per hour. Primary causes of the motion are (1) changes to the thermal design dictated by the warmer Aft Shroud environment and (2) on-orbit power cycling of Multi-Anode Microchannel Arrays (MAMA) electronics to minimize the effects of radiation hits on the MAMA detectors. The rear portion of the STIS optical bench is too warm to be held at a constant temperature by internal heaters. Electronics swing in temperature with an orbital and daily frequency. The thermal drift of the optical formats is not negligible, but is well behaved in most circumstances. The observer is advised to examine the trade-off between the most accurate wavelengths with best spectral/spatial resolutions versus increased overheads that directly affect the observing times. A long term concern is that the Aft Shroud thermal environment is predicted to heat up as much as one Centigrade degree per year. Progressively more of the bench would move out of thermal control. Thus the external cooler for STIS, being considered for the Third Servicing Mission is of major importance to the long term operation of STIS.
Gull, Theodore R.↗
LISA Optics Model
The Laser Interferometer Space Antenna (LISA) experiment has six telescopes, in three spacecraft, in orbit about the sun. There is a continuous two-way laser link between all of the spacecraft. The ability to make sub picometer level performance predictions about the interferometry for such a large optical system which has major subassemblies separated by 5 million kilometer distances which are constantly moving with respect to each other requires a slight extension of existing optical analysis techniques. To see this a description of the approach used to model all of the optics, in the spacecraft in orbit, is presented and the ability of this model to analyze requirements is discussed.
Waluschka, Eugene↗
Optic Nerve Sheath Mechanics in VIIP Syndrome
Visual Impairment Intracranial Pressure (VIIP) syndrome is a major concern in current space medicine research. While the exact pathology of VIIP is not yet known, it is hypothesized that the microgravity-induced cephalad fluid shift increases intracranial pressure (ICP) and drives remodeling of the optic nerve sheath. To investigate this possibility, we are culturing optic nerve sheath dura mater samples under different pressures and investigating changes in tissue composition. To interpret results from this work, it is essential to first understand the biomechanical response of the optic nerve sheath dura mater to loading. Here, we investigated the effects of mechanical loading on the porcine optic nerve sheath.Porcine optic nerves (number: 6) were obtained immediately after death from a local abattoir. The optic nerve sheath (dura mater) was isolated from the optic nerve proper, leaving a hollow cylinder of connective tissue that was used for biomechanical characterization. We developed a custom mechanical testing system that allowed for unconfined lengthening, twisting, and circumferential distension of the dura mater during inflation and under fixed axial loading. To determine the effects of variations in ICP, the sample was inflated (0-60 millimeters Hg) and circumferential distension was simultaneously recorded. These tests were performed under variable axial loads (0.6 grams - 5.6 grams at increments of 1 gram) by attaching different weights to one end of the dura mater. Results and Conclusions: The samples demonstrated nonlinear behavior, similar to other soft connective tissue (Figure 1). Large increases in diameter were observed at lower transmural pressures (approximately 0 to 5 millimeters Hg), whereas only small diameter changes were observed at higher pressures. Particularly interesting was the existence of a cross-over point at a pressure of approximately 11 millimeters Hg. At this pressure, the same diameter is obtained for all axial loads applied to the tissue; i.e., as the axial load is varied, the diameter of the dura mater remains constant. This cross-over in the pressure-diameter curves occurred in all optic nerve sheaths that were tested, and may correspond with in vivo ICP levels for pigs. These data suggest that diameter of the dura mater of the optic nerve remains nearly constant in vivo despite being stretched axially. This may be a homeostatic mechanism aimed at maintaining target stresses/strains on the cells in the dura mater, and deviations from these stresses may play an important role in optic nerve sheath remodeling. Future studies will involve subjecting the dura mater to varying pressures and axial tensions for extended periods of time, while monitoring changes in the biomechanical properties. The data can then be used to study the effects of changes in ICP on the remodeling of the dura mater.
biomechanics↗
Optical Processing of Speckle Images with Bacteriorhodopsin for Pattern Recognition
Logarithmic processing of images with multiplicative noise characteristics can be utilized to transform the image into one with an additive noise distribution. This simplifies subsequent image processing steps for applications such as image restoration or correlation for pattern recognition. One particularly common form of multiplicative noise is speckle, for which the logarithmic operation not only produces additive noise, but also makes it of constant variance (signal-independent). We examine the optical transmission properties of some bacteriorhodopsin films here and find them well suited to implement such a pointwise logarithmic transformation optically in a parallel fashion. We present experimental results of the optical conversion of speckle images into transformed images with additive, signal-independent noise statistics using the real-time photochromic properties of bacteriorhodopsin. We provide an example of improved correlation performance in terms of correlation peak signal-to-noise for such a transformed speckle image.
Downie, John D.↗
Utilizing Site Disorder in the Development of New Energy-Relevant Semiconductors
We report controlling site disorder in ternary and multinary compounds enables tuning optical and electronic properties at fixed lattice constants and stoichiometries, moving beyond many of the challenges facing binary alloy systems. Here, we consider possible enhancements to energy-related applications through the integration of disorder-tunable materials in devices such as light-emitting diodes, photonics, photovoltaics, photocatalytic materials, batteries, and thermoelectrics. However, challenges remain in controlling and characterizing disorder. Focusing primarily on II–IV–V 2 materials, we identify three metrics for experimentally characterizing cation site disorder. Complementary to these experiments, we discuss simulation methods to understand disordered materials. Nonidealities, such as off-stoichiometry and oxygen incorporation, can occur while synthesizing metastable disordered materials. While nonidealities may seem undesirable, we describe how if harnessed they could provide another knob for tuning disorder and subsequently properties. To illustrate the effects of disorder on device-relevant properties, we provide case examples of disordered materials and their potential in device applications.
36 MATERIALS SCIENCE↗
Electron spin resonance of acenaphthene radical ion and radical ion pairs.
Na- acenaphthene reaction temperature dependence, studying optical density, precipitation, ion pair formation, coupling constants and hyperfine structure
ALKALI METAL↗
Radiation effects on beta 10.6 of pure and europium doped KCl
Changes in the optical absorption coefficient as a result of X-ray and electron bombardment of pure KCl (monocrystalline and polycrystalline), and divalent europium doped polycrystalline KCl were determined. The optical absorption coefficients were measured by a constant heat flow calorimetric method. Both 300 KV X-irradiation and 2 MeV electron irradiation produced significant increases in beta 10.6, measured at room temperature. The X-irradiation of pure moncrystalline KCl increased beta 10.6 by 0.005/cm for a 113 MR dose. For an equivalent dose, 2 MeV electrons were found less efficient in changing beta 10.6. However, electron irradiation of pure and Eu-doped polycrystalline KCl produced marked increases in adsorption. Beta increased to over 0.25/cm in Eu-doped material for a 30 x 10 to the 14th power electrons/sq cm dose, a factor of 20 increase over unirradiated material. Moreover, bleaching the electron irradiated doped KCl with 649 m light produced and additional factor of 1.5 increase. These findings will be discussed in light of known defect-center properties in KCl.
Grimes, H. H.↗
Calcium abundance variations in diffuse interstellar clouds
Observations are discussed which show that the Na I/H2 column-density ratio is relatively constant among different clouds where H2 is optically thin, but the Na I/Ca II column-density ratio varies. This implies that the gas-phase abundance of calcium is variable. It is proposed that the wide variation in the gas-phase calcium abundance can be explained by small variations in the calcium content of grains. The observed enhancement of the Ca II/Na I column-density ratio with cloud velocity is attributed to grain destruction in grain-grain collisions within the same cloud. The structure of shock waves propagating through the interstellar gas is computed, and the grain-destruction model is compared with observational data.
Jura, M.↗
Tracking falling objects
Moving lens follows movement of object accelerated by gravity. Lenses and mirrors maintain constant magnification regardless of distance between moving optical carriage mechanism and fixed telescope. Device tracks objects up to 2 cm in diameter over vertical distance of 2 m.
Frazer, R. E.↗
Theory of the optimally coupled Q-switched laser
The general equations describing Q-switched laser operation are transcendental in nature and require numerical solutions, which greatly complicates the optimization of real devices. Here, it is shown that, using the mathematical technique of Lagrange multipliers, one can derive simple analytic expressions for all of the key parameters of the optimally coupled laser, i.e., one which uses an optimum reflector to obtain maximum laser efficiency for a given pump level. These parameters can all be expressed as functions of a single dimensionless variable z, defined as the ratio of the unsaturated small-signal gain to the dissipative (nonuseful) optical loss, multiplied by a few simple constants. Laser design tradeoff studies and performance projections can be accomplished quickly with the help of several graphs and a simple hand calculator. Sample calculations for a high-gain Nd:YAG and a low-gain alexandrite laser are presented as illustrations of the technique.
Degnan, John J.↗
Low dielectric fluorinated poly(phenylene ether ketone) film and coating
The present invention relates to film and coating materials prepared from novel fluorinated poly(phenylene ether ketones). A fluorinated poly(phenylene ether ketone) is prepared by reacting a bisphenol with 1,1,1,3,3,3 hexafluoro-2,2-bis 4-(4-halobenzoyl) phenyl propane (wherein halo is fluoro or chloro), which is a novel monomer formed as the reaction product of halobenzene (wherein halo is fluoro or chloro) and 1,1,1,3,3,3 hexafluoro-2,2-bis (p-chloro formyl phenyl) propane. Especially beneficial results of this invention are that films and coating materials prepared from the novel fluorinated poly(phenylene ether ketone) are essentially optically transparent/colorless and have a lower dielectric constant than otherwise comparable, commercially available poly(phenylene ether ketones). Moreover, unlike the otherwise comparable commercially available materials, the novel fluorinated poly(phenylene ether ketones) of the present invention can be solution cast or sprayed to produce the films and coatings. Furthermore, the long term thermal stability of the polymers of the present invention is superior to that of the commercially available materials.
Cassidy, Patrick E.↗
The first linear polarization spectra of Wolf-Rayet stars in the ultraviolet - EZ Canis Majoris and Theta Muscae
During the 1990 December Astro-1 Space Shuttle mission, spectropolarimetry was conducted in the wavelength region from 1400 to 3200 A of the Wolf-Rayet stars EZ CMa (WN5) and Theta Mus (WC6 + O9.5I) with the Wisconsin Ultraviolet Photo-Polarimeter Experiment. The UV polarization of EZ CMa displays features which correspond to emission lines. This indicates a large, about 0.8 percent, intrinsic UV-continuum polarization, and provides further evidence that the wind of EZ CMa is highly distorted. The polarization of Theta Mus does not change across emission lines, or the strong interstellar 2200 A feature. The polarization decreases smoothly to shorter wavelengths, at constant position angle. The combined UV-optical polarization spectrum of Theta Mus can be described well with interstellar polarization following a Serkowski law.
Schulte-Ladbeck, R. E.↗
Botswana water and surface energy balance research program. Part 2: Large scale moisture and passive microwaves
The Botswana water and surface energy balance research program was developed to study and evaluate the integrated use of multispectral satellite remote sensing for monitoring the hydrological status of the Earth's surface. The research program consisted of two major, mutually related components: a surface energy balance modeling component, built around an extensive field campaign; and a passive microwave research component which consisted of a retrospective study of large scale moisture conditions and Nimbus scanning multichannel microwave radiometer microwave signatures. The integrated approach of both components are explained in general and activities performed within the passive microwave research component are summarized. The microwave theory is discussed taking into account: soil dielectric constant, emissivity, soil roughness effects, vegetation effects, optical depth, single scattering albedo, and wavelength effects. The study site is described. The soil moisture data and its processing are considered. The relation between observed large scale soil moisture and normalized brightness temperatures is discussed. Vegetation characteristics and inverse modeling of soil emissivity is considered.
Vandegriend, A. A.↗
Absolute determination of local tropospheric OH concentrations
Long path absorption (LPA) according to Lambert Beer's law is a method to determine absolute concentrations of trace gases such as tropospheric OH. We have developed a LPA instrument which is based on a rapid tuning of the light source which is a frequency doubled dye laser. The laser is tuned across two or three OH absorption features around 308 nm with a scanning speed of 0.07 cm(exp -1)/microsecond and a repetition rate of 1.3 kHz. This high scanning speed greatly reduces the fluctuation of the light intensity caused by the atmosphere. To obtain the required high sensitivity the laser output power is additionally made constant and stabilized by an electro-optical modulator. The present sensitivity is of the order of a few times 10(exp 5) OH per cm(exp 3) for an acquisition time of a minute and an absorption path length of only 1200 meters so that a folding of the optical path in a multireflection cell was possible leading to a lateral dimension of the cell of a few meters. This allows local measurements to be made. Tropospheric measurements have been carried out in 1991 resulting in the determination of OH diurnal variation at specific days in late summer. Comparison with model calculations have been made. Interferences are mainly due to SO2 absorption. The problem of OH self generation in the multireflection cell is of minor extent. This could be shown by using different experimental methods. The minimum-maximum signal to noise ratio is about 8 x 10(exp -4) for a single scan. Due to the small size of the absorption cell the realization of an open air laboratory is possible in which by use of an additional UV light source or by additional fluxes of trace gases the chemistry can be changed under controlled conditions allowing kinetic studies of tropospheric photochemistry to be made in open air.
Armerding, Wolfgang↗
Approaches to Validation of Models for Low Gravity Fluid Behavior
This paper details the author experiences with the validation of computer models to predict low gravity fluid behavior. It reviews the literature of low gravity fluid behavior as a starting point for developing a baseline set of test cases. It examines authors attempts to validate their models against these cases and the issues they encountered. The main issues seem to be that: Most of the data is described by empirical correlation rather than fundamental relation; Detailed measurements of the flow field have not been made; Free surface shapes are observed but through thick plastic cylinders, and therefore subject to a great deal of optical distortion; and Heat transfer process time constants are on the order of minutes to days but the zero-gravity time available has been only seconds.
Chato, David J.↗