Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OXIDATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2014

High Pressure Steam Oxidation of Alloys for Advanced Ultra-Supercritical Conditions

A steam oxidation test was conducted at 267 ± 17 bar and 670°C for 293 hr. A comparison test was run at 1 bar. All of the alloys showed an increase in scale thickness and oxidation rate with pressure, and TP304H and IN625 had very large increases. Fine-grained TP304H at 267 bar behaved like a coarse grained alloy, indicative of high pressure increasing the critical Cr level needed to form and maintain a chromia scale. At 267 bar H230, H263, H282, IN617 and IN740 had kp values a factor of one–to-two orders of magnitude higher than at 1 bar. IN625 had a four order of magnitude increase in kp at 267 bar compared to 1 bar. Possible causes for increased oxidation rates with increased pressure were examined, including increased solid state diffusion within the oxide scale and increased critical Cr content to establish and maintain a chromia scale.

Steam, Oxidation, Superalloy, Pressure, Advanced U↗
DOE OSTI2020

Recent Advances in the Understanding of Boron-Containing Catalysts for the Selective Oxidation of Alkanes to Olefins

The production of ethylene and propylene through aerobic alkane oxidation without significant coproduction of CO and CO 2 (CO x ) presents a challenge to academic and industrial researchers alike. Recently, boron-containing materials such as hexagonal boron nitride (hBN) have been identified as active and selective catalysts for the oxidative dehydrogenation (ODH) of propane to propylene with minimal CO x selectivity. Additionally, high olefin selectivity is also obtained in the oxidation of other alkanes and other materials such as metal borides and supported B/SiO 2 have been successfully applied to this transformation. Here, recent advances in the understanding of these catalysts in the oxidation of light alkanes are presented here providing a framework for further study of this exciting field.

03 NATURAL GAS↗
DOE OSTI2026

Oxide nucleation via threshold-driven volume instability in Ni oxidation

Oxide nucleation dictates the onset of metal oxidation, yet the atomistic pathways bridging initial oxygen adsorption to bulk phase transformation remain elusive. Here, we utilize in-situ atomic-resolution imaging to directly capture the nucleation of nickel oxide, revealing a threshold-driven, cooperative transformation of Ni into NiO. Our observations identify a distinct incubation period during which oxygen progressively accumulates in subsurface layers. Once a critical concentration and penetration depth are reached, a collective lattice reconfiguration is triggered, abruptly converting multiple Ni layers into NiO. Atomistic simulations corroborate this mechanism, identifying a cooperative lattice instability induced by subsurface oxygen saturation. These results establish subsurface oxygen incorporation as the missing mechanistic link between surface adsorption and three-dimensional oxide formation, providing an atomistic framework to understand and control reactive phase transformations in materials synthesis, catalysis, and degradation.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Vapor phase hydrogenation of furfural over nickel mixed metal oxide catalysts derived from layered double hydroxides

The hydrogenation of furfural is investigated over various reduced nickel mixed metal oxides derived from layered double hydroxides (LDHs) containing Ni-Mg-Al and Ni-Co-Al. Upon reduction, relatively large Ni(0) domains develop in the Ni-Mg-Al catalysts, whereas in the Ni-Co-Al catalysts smaller metal particles of Ni(0) and Co(0), potentially as alloys, are formed, as evidenced by XAS, XPS, STEM and EELS. All the reduced Ni catalysts display similar selectivities towards major hydrogenation products (furfuryl alcohol and tetrahydrofurfuryl alcohol), though the side products varied with the catalyst composition. The 1.1Ni-0.8Co-Al catalyst showed the greatest activity per titrated site when compared to the other catalysts, with promising activity compared to related catalysts in the literature. The use of base metal catalysts for hydrogenation of furanic compounds may be a promising alternative to the well-studied precious metal catalysts for making biomass-derived chemicals if catalyst selectivity can be improved in future work by alloying or tuning metal-oxide support interactions.

biomass↗
DOE OSTI2019

Aerobic oxidative coupling of amines to imines by mesoporous copper aluminum mixed metal oxides via generation of Reactive Oxygen Species (ROS)

We report a mesoporous, monomodal copper aluminum mixed metal oxide (MMO) (average pore size 9.63 nm, surface area 140 m 2 /g) synthesized via a modified inverse micelle method, efficiently catalyzes aerobic oxidative coupling of amines to imines. This material exhibits excellent conversion (> 99%) and selectivity (> 99%) towards imine synthesis under mild, solvent free, green conditions utilizing atmospheric air as the sole oxidant. Catalytic activity is observed for a diverse range of amine substrates. The aerobic oxidation of amines to imines follows a unique mechanistic pathway which involves Reactive Oxygen Species (ROS).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Grain boundary selective oxidation and intergranular stress corrosion crack growth of high-purity nickel binary alloys in high-temperature hydrogenated water

The effects of alloying elements in Ni-5at%X binary alloys on intergranular (IG) corrosion and stress corrosion cracking (SCC) have been assessed in 300-360°C hydrogenated water at the Ni/NiO stability line. Alloys with Cr or Al additions exhibited grain boundary oxidation and IGSCC, while localized degradation was not observed for pure Ni, Ni-Cu or Ni-Fe alloys. Environment-enhanced crack growth was determined by comparing the response in water and N2 gas. Results demonstrate that selective grain boundary oxidation of Cr and Al promoted IGSCC of these Ni alloys in hydrogenated water.

Environmental Molecular Sciences Laboratory↗
DOE OSTI2018

Molecular dynamics simulations of zinc oxide solubility: From bulk down to nanoparticles

The solubility of metal oxides is one of the key descriptors for the evaluation of their potential toxic effects, both in the bulk form and in nanoparticulated aggregates. Current work presents a new methodology for the in silico assessment of the solubility of metal oxides, which is demonstrated using a well-studied system, ZnO. The calculation of the solubility is based on statistical thermodynamics tools combined with Density Functional Tight Binding theory for the evaluation of the free energy exchange during the dissolution process. Models of small ZnO clusters are used for describing the final dissolved material, since the complete ionic dissolution of ZnO is hindered by the formation of O2- anions in solution, which are highly unstable. Results show very good agreement between the computed solubility values and experimental data for ZnO bulk, up to 0.5 mg·L-1 and equivalents of 50 g·L-1 for the free Zn2+ cation in solution. However, the reference model for solid nanoparticles formed by free space nanoparticles can only give a limited quantitative solubility evaluation for ZnO nanoparticles.

DFTB modelling↗
DOE OSTI2017

Coupling metal oxide nanoparticle catalysts for water oxidation to molecular light absorbers

Water oxidation, as a mandatory reaction of solar fuels conversion systems, requires the use of light absorbers with electronic properties that are well matched with those of the multi-electron catalyst in order to achieve high efficiency. Molecular light absorbers offer flexibility in fine tuning of orbital energetics, and metal oxide nanoparticles have emerged as robust oxygen evolving catalysts. These material choices offer a promising approach for the development of photocatalytic systems for water oxidation. However, efficient charge transfer coupling of molecular light absorbers and metal oxide nanoparticle catalysts has proven a challenge. Recent new approaches toward the efficient coupling of these components based on synthetic design improvements combined with direct spectroscopic observation and kinetic evaluation of charge transfer processes are discussed in this paper.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Preparation of aluminum hydroxide and oxide nanostructures with controllable morphology by wet oxidation of AlN/Al nanoparticles

Highlights: • Aluminum hydroxide nanoparticles were synthesized by wet oxidation methods. • The oxidation conditions of AlN/Al affect the morphologies of the reaction products. • No changes in the synthesized materials morphology occurred up to 1000 °C. • The maxima specific surface areas for the nanostructures were achieved at 500 °C. - Abstract: A simple and environmentally friendly method to prepare aluminum oxyhydroxide and trihydroxide nanostructures by wet oxidation of AlN/Al composite nanoparticles was developed. The AlN/Al nanoparticles used were produced by electrical explosion of an aluminum wire in nitrogen atmosphere. The obtained nanostructures were characterized employing X-ray diffraction (XRD), transmission and high-resolution scanning electron microscopy (TEM and HRSEM), thermogravimetric analysis (TGA) and N{sub 2} adsorption-desorption technique (BET). By changing the wet oxidation conditions, aluminum hydroxides with different phase composition, morphology and texture characteristics were synthesized. After calcination at different temperatures, a range of transition and stable alumina nanostructures were obtained that preserved the morphology of the aluminum hydroxide precursors - agglomerated nanosheets, nanoplates or hexagonal nanorods, up to 1000 °C. Optimal process parameters for maximum surface area development for all the precursor materials have been established.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Radiation resistance of oxide dispersion strengthened alloys: Perspectives from in situ observations and rate theory calculations

Here, in situ ion irradiation and rate theory calculations were employed to directly compare the radiation resistance of an oxide dispersion strengthened alloy with that of a conventional ferritic/martensitic alloy. Compared to the rapid buildup of dislocation loops, loop growth, and formation of network dislocations in the conventional ferritic/martensitic alloy, the superior radiation resistance of the oxide dispersion strengthened alloy is manifested by its stable dislocation structure under the same irradiation conditions. Thus, the results are consistent with rate theory calculations, which show that high-density nanoparticles can significantly reduce freely migrating defects and suppress the buildup of clustered defects.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultrathin silicon oxide prepared by in-line plasma-assisted N 2 O oxidation (PANO) and the application for n-type polysilicon passivated contact

We develop a plasma-assisted nitrous-oxide (N 2 O) gas oxidation (PANO) method to prepare the ultrathin silicon oxide (SiO x ) for polysilicon (poly-Si) passivated contact. The effects of preparation conditions, including the substrate temperature, processing time, and plasma power, are studied. Afterwards, we integrate the PANO SiO x into the polysilicon passivated contact and optimize the passivation and contact performances. Excellent surface passivation with the n-type poly-Si and PANO SiO x on the n-type c-Si wafer is achieved by 880 °C annealing, which shows competitive passivation quality to the one with NASO SiO x . Champion implied open-circuit voltage (iV oc ) and single-sided recombination saturated current (J 0 ) reach 730 mV and 4.3 fA/cm 2 after crystallization; and they are further improved to 747 mV and 2.0 fA/cm 2 (3 × 10 15 cm -3 ) after subsequent AlO x /SiN x hydrogenation. Using transmission electron microscopy (TEM), we find that the thickness of PANO SiO x ranges 1.1–2.4 nm and the controlled nitric acid oxidized SiO x (NAOS) ranges 1.3–1.8 nm. The contact resistivity (ρ c ) is typically <10 mΩ cm 2 with the annealing temperature of >820 °C. Also, the crystallinity, phosphorous in-diffusion profile, and current-leaking density of the passivated contacts are investigated. In general, the PANO SiO x and in-situ doping amorphous silicon precursor can be fabricated in one PECVD system without additional equipment or transfer procedures, which is favorable for the high-efficiency, low-cost industrial manufacture.

14 SOLAR ENERGY↗
DOE OSTI2015

Complex catalytic behaviors of CuTiO x mixed-oxide during CO oxidation

Mixed metal oxides have attracted considerable attention in heterogeneous catalysis due to the unique stability, reactivity, and selectivity. Here, the activity and stability of the CuTiO x monolayer film supported on Cu(111), CuTiO x /Cu(111), during CO oxidation was explored using density functional theory (DFT). The unique structural frame of CuTiO x is able to stabilize and isolate a single Cu + site on the terrace, which is previously proposed active for CO oxidation. Furthermore, it is not the case, where the reaction via both the Langmuir–Hinshelwood (LH) and the Mars-van Krevelen (M-vK) mechanisms are hindered on such single Cu + site. Upon the formation of step-edges, the synergy among Cu δ+ sites, TiO x matrix, and Cu(111) is able to catalyze the reaction well. Depending on temperatures and partial pressure of CO and O 2 , the surface structure varies, which determines the dominant mechanism. In accordance with our results, the Cu δ+ ion alone does not work well for CO oxidation in the form of single sites, while the synergy among multiple active sites is necessary to facilitate the reaction.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Mechanistic Studies of the Oxidation of Cyclohexene to 2-Cyclohexen-1-one over ALD Prepared Titania Supported Vanadia

Selective oxidation of cyclohexene to 2-cyclohexen-1-one over titania supported vanadia (VO x /TiO 2 ) has been studied using temperature dependent in-situ FTIR spectroscopy in both the presence and absence of oxygen. The VO x /TiO 2 samples were prepared using one atomic layer deposition (ALD) cycle and characterized by Raman spectroscopy. In-situ FTIR data for the oxidation of cyclohexene and perdeuterocyclohexene allow for the formulation of a molecular level reaction mechanism, which is initiated by the transfer of an allyl hydrogen. Oxidation of perdeuterocyclohexene provides a direct probe of the formation of OD and HDO moieties that support the involvement of specific steps in the proposed mechanism. The presence of gas phase oxygen does not lead to a change in the products versus anaerobic conditions. However, gas phase oxygen is significantly incorporated in the CO 2 over-oxidation product above ~250 °C. Data were also obtained with cyclohexene epoxide as the reactant in an effort to determine whether there is a parallel reaction pathway, which is initiated by C=C activation in cyclohexene, that involves cyclohexene epoxide as an intermediate. Furthermore, though a minor pathway involving a cyclohexene epoxide intermediate cannot be ruled out, these data demonstrate that, under experimental conditions, the dominant pathway from cyclohexene to cyclohexene-1-one is initiated by an allyl-H activation step and does not involve an epoxide intermediate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Regeneration of Active Surface Alloys during Cyclic Oxidation and Reduction: Oxidation of H 2 on Pd/Ag(111)

The surface morphology and composition of a catalyst during excursions between oxidizing and reducing conditions can change substantially, especially in bimetallic alloys. Both thermodynamic and kinetic factors play a role in determining the properties of alloy surfaces where the active phase may be a metastable state. Previously, Ag oxide reduction was shown to be dramatically enhanced when Pd is on the surface; however, Pd is more stable when dissolved in Ag, raising the question as to whether a highly active Pd surface state will persist over multiple reaction cycles—a requirement for catalytic function. Experiments herein demonstrate that the enhanced chemical functionality due to the presence of Pd on the surface is retained, based on the enhanced rate of silver oxide reduction over multiple oxidation/reduction cycles for a Pd/Ag(111) model. Repeated oxidation and reduction promote PdAg alloying and reversible structural and compositional changes are detected using X-ray photoelectron spectroscopy. Furthermore, this study establishes that metastable phases can persist in reactive processes on surfaces, indicating their potential in heterogeneous catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Highly Oxidized Oxide Surface toward Optimum Oxygen Evolution Reaction by Termination Engineering

The oxygen evolution reaction (OER) is a critical step for sustainable fuel production through electrochemistry process. Maximizing active sites of nanocatalyst with enhanced intrinsic activity, especially the activation of lattice oxygen, is gradually recognized as the primary incentive. Since the surface reconfiguration to oxyhydroxide is unavoidable for oxygen-activated transition metal oxides, developing a surface termination like oxyhydroxide in oxides is highly desirable. In this work, we demonstrate an unusual surface termination of (111)-facet Co 3 O 4 nanosheet that is exclusively containing edge-sharing octahedral Co 3+ similar to CoOOH that can perform at approximately 40 times higher current density at 1.63 V (vs RHE) than commercial RuO 2 . It is found that this surface termination has an oxidized oxygen state in contrast to standard Co-O systems, which can serve as active site independently, breaking the scaling relationship limit. Finally, this work forwards the applications of oxide electrocatalysts in the energy conversion field by surface termination engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Characterization of low-temperature microwave loss of thin aluminum oxide formed by plasma oxidation

We report on the characterization of microwave loss of thin aluminum oxide films at low temperatures using superconducting lumped resonators. The oxide films are fabricated using plasma oxidation of aluminum and have a thickness of 5 nm. We measure the dielectric loss versus microwave power for resonators with frequencies in the GHz range at temperatures from 54 to 303 mK. The power and temperature dependence of the loss are consistent with the tunneling two-level system theory. These results are relevant to understanding decoherence in superconducting quantum devices. The obtained oxide films are thin and robust, making them suitable for capacitors in compact microwave resonators.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

High stability mechanisms of quinary indium gallium zinc aluminum oxide multicomponent oxide films and thin film transistors

Quinary indium gallium zinc aluminum oxide (IGZAO) multicomponent oxide films were deposited using indium gallium zinc oxide (IGZO) target and Al target by radio frequency magnetron cosputtering system. An extra carrier transport pathway could be provided by the 3 s orbitals of Al cations to improve the electrical properties of the IGZO films, and the oxygen instability could be stabilized by the strong Al-O bonds in the IGZAO films. The electron concentration change and the electron mobility change of the IGZAO films for aging time of 10 days under an air environment at 40 °C and 75% humidity were 20.1% and 2.4%, respectively. The experimental results verified the performance stability of the IGZAO films. Compared with the thin film transistors (TFTs) using conventional IGZO channel layer, in conducting the stability of TFTs with IGZAO channel layer, the transconductance g{sub m} change, threshold voltage V{sub T} change, and the subthreshold swing S value change under the same aging condition were improved to 7.9%, 10.5%, and 14.8%, respectively. Furthermore, the stable performances of the IGZAO TFTs were also verified by the positive gate bias stress. In this research, the quinary IGZAO multicomponent oxide films and that applied in TFTs were the first studied in the literature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

The onset of sub-surface oxidation induced by defects in a chemisorbed oxygen layer

We investigate the onset of internal oxidation of a Cu(110) surface induced by oxygen subsurface adsorption via defects in the Cu(110)–(2 × 1)–O chemisorbed layer. The presence of a boundary formed by merged add-row structure domains due to a mismatch of half unit-cell leads to preferred oxygen adsorption at the subsurface tetrahedral sites. The resulting distorted Cu–O tetrahedra along the domain boundary have comparable bond length and angles to those of the bulk oxide phase of Cu{sub 2}O. Our results indicate that the presence of defects in the oxygen-chemisorbed adlayer can lead to the internal oxidation via the formation of Cu{sub 2}O-like tetrahedra in between the topmost and second outermost atomic layers at the oxygen coverage θ = 0.53 and the second and third outermost atomic layers at θ = 0.56. These results show that the internal oxidation of a metal surface can occur in the very beginning of the oxygen chemisorption process enabled by the presence of defects in the oxygen chemisorbed layer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗