Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MATRIX MATERIALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Thermal degradation of the tensile strength of unidirectional boron/aluminum composites

The variation of ultimate tensile strength with thermal treatment of B-Al composite materials and of boron fibers chemically removed from these composites is studied systematically in an attempt to determine the mechanism of the resulting strength degradation. The results indicate that thermally cycling of B-Al represents a more severe condition than equivalent time at temperature. Degradation of composite tensile strength from about 1.3 GN/sq m to as low as 0.34 GN/sq m was observed after 3000 cycles to 420 C for 203-micron B-1100 Al composite. In general, the 1100 Al-matrix composites degraded somewhat more than the 6061 matrix material studied. Measurement of fiber strengths confirmed a composite strength loss due to the degradation of fiber strength. Microscopy indicated a highly flawed fiber surface. On the basis of various thermal-cycling studies and electron diffraction analysis, a mechanism is favored in which B reacts with Al, freshly exposed by cold working during cycling, to form AlB2. The nonuniform interface reaction leads to a highly flawed and weakened B fiber.

Grimes, H. H.↗

Optimal Substrate Preheating Model for Thermal Spray Deposition of Thermosets onto Polymer Matrix Composites

High velocity oxy-fuel (HVOF) sprayed, functionally graded polyimide/WC-Co composite coatings on polymer matrix composites (PMC's) are being investigated for applications in turbine engine technologies. This requires that the polyimide, used as the matrix material, be fully crosslinked during deposition in order to maximize its engineering properties. The rapid heating and cooling nature of the HVOF spray process and the high heat flux through the coating into the substrate typically do not allow sufficient time at temperature for curing of the thermoset. It was hypothesized that external substrate preheating might enhance the deposition behavior and curing reaction during the thermal spraying of polyimide thermosets. A simple analytical process model for the deposition of thermosetting polyimide onto polymer matrix composites by HVOF thermal spray technology has been developed. The model incorporates various heat transfer mechanisms and enables surface temperature profiles of the coating to be simulated, primarily as a function of substrate preheating temperature. Four cases were modeled: (i) no substrate preheating; (ii) substrates electrically preheated from the rear; (iii) substrates preheated by hot air from the front face; and (iv) substrates electrically preheated from the rear and by hot air from the front.

Ivosevic, M.↗

Hierarchically porous and single Zn atom-embedded carbon molecular sieves for H2 separations

Abstract Hierarchically porous materials containing sub-nm ultramicropores with molecular sieving abilities and microcavities with high gas diffusivity may realize energy-efficient membranes for gas separations. However, rationally designing and constructing such pores into large-area membranes enabling efficient H 2 separations remains challenging. Here, we report the synthesis and utilization of hybrid carbon molecular sieve membranes with well-controlled nano- and micro-pores and single zinc atoms and clusters well-dispersed inside the nanopores via the carbonization of supramolecular mixed matrix materials containing amorphous and crystalline zeolitic imidazolate frameworks. Carbonization temperature is used to fine-tune pore sizes, achieving ultrahigh selectivity for H 2 /CO 2 (130), H 2 /CH 4 (2900), H 2 /N 2 (880), and H 2 /C 2 H 6 (7900) with stability against water vapor and physical aging during a continuous 120-h test.

42 ENGINEERING↗

Quantification of Error Associated with Using Misaligned Meshes in Continuum Damage Mechanics Material Models for Matrix Crack Growth Predictions in Composites

The ability of a material model to capture in-plane matrix mode I and mode II crack growth is an essential component for modeling ply level damage evolution in composite structures. Previous studies using a continuum damage mechanics (CDM) approach have shown success in satisfying benchmark solutions for mode I and II crack growth. However, success was shown using a fiber-aligned meshing strategy, which encourages matrix cracks to propagate in a single band of elements, along the fiber direction. Generating a fiber-aligned mesh becomes a highly involved process for laminates including off-axis (non 0° or 90°) plies. The objective of this study is to quantify the effect of non-fiber aligned mesh discretization on predictions of in-plane matrix crack propagation. The approach taken incrementally varies the mesh orientation angle relative to the fiber orientation; more specifically, misaligned meshes are used to quantify the effect of element angle orientation relative to the initial crack orientation on the energy released during matrix crack propagation simulations using a CDM method. CDM solutions obtained with the misaligned meshes are evaluated against known benchmarks for mode I and II matrix crack growth. The CDM solutions reveal a near-polynomial trend of increased predicted failure stress with increased mesh misalignment angle; hence implying a potential relationship between element orientation angle and apparent fracture toughness.

Justusson, Brian↗

Predicting the Influence of Pore Characteristics on Ductility of Thin-Walled High Pressure Die Casting Magnesium

In this paper, a two-dimensional microstructure-based finite element modeling method is adopted to investigate the effects of porosity in thin-walled high pressure die casting Mg materials on their ductility. For this purpose, the cross-sections of AM50 and AM60 casting samples are first examined using optical microscope to obtain the overall information on the pore characteristics. The experimentally quantified pore characteristics are then used to generate a series of synthetic microstructures with different pore sizes, pore volume fractions and pore size distributions. Pores are explicitly represented in the synthetic microstructures and meshed out for the subsequent finite element analysis. In the finite element analysis, an intrinsic critical strain value is used for the Mg matrix material, beyond which work-hardening is no longer permissible. With no artificial failure criterion prescribed, ductility levels are predicted for the various microstructures in the form of strain localization. Mesh size effect study is also conducted, from which a mesh size dependent critical strain curve is determined. A concept of scalability of pore size effects is then presented and examined with the use of the mesh size dependent critical strain curve. The results in this study show that, for the regions with lower pore size and lower volume fraction, the ductility generally decreases as the pore size and pore volume fraction increase whereas, for the regions with larger pore size and larger pore volume fraction, other factors such as the mean distance between the pores begin to have some substantial influence on the ductility. The results also indicate that the pore size effects may be scalable for the models with good-representative pore shape and distribution with the use of the mesh size dependent critical strain curve.

Sun, Xin↗

Method for Molding Planar Billet of Thermally Insulative Material Into Predetermined Non-Planar Shape

A method and apparatus is discussed for molding thermal protection system (TPS) tiles for spacecraft. The apparatus and method include a bottom mold member defining a mold surface shaped like a surface of the spacecraft, e.g., the nose cap of wing leading edge, sought to be thermally protected. A flat billet of TPS material is positioned over the periphery of the mold surface, and a hollow weight element that has a periphery configured like the periphery of the mold surface is positioned on the billet. The billet is then heated in accordance with a predetermined heating regime, and during the heating process the weight of the weight element causes the billet to deform to assume the shape of the mold surface. If desired, a TUFI coating is impregnated into the billet prior to heating, and the coating is sintered to the billet during heating. After heating, a composite matrix material, e.g., a graphite or fiberglass cloth which is impregnated with epoxy or polimide, is bonded to the now-shaped tile to support the tile. Silicone can then be impregnated into the now-formed tile to provide flexibility of the tile.

Kolodziej, Paul↗

Synthetic Coal Slag Infiltration into Varying Refractory Materials

The infiltrations of synthetic coal slag into 99%Al{sub 2}O{sub 3}, 85%Al{sub 2}O{sub 3}–15%SiO{sub 2}, and 90%Cr{sub 2}O{sub 3}–10%Al{sub 2}O{sub 3} refractories with a temperature gradient induced along the penetration direction were compared to one another. The infiltrating slag was synthesized with a composition that is representative of an average of the ash contents from U S coal feedstock. Experiments were conducted with a hot-face temperature of 1450°C in a CO/CO{sub 2} atmosphere. Minimal penetration was observed in the 90%Cr{sub 2}O{sub 3}–10%Al{sub 2}O{sub 3} material because interactions between the refractory and the slag produced a protective layer of FeCr{sub 2}O{sub 4}, which impeded slag flow into the bulk of the refractory. After 5 h, the 99%Al{sub 2}O{sub 3} sample exhibited an average penetration of 12.7 mm whereas the 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} sample showed 3.8 mm. Slag infiltrated into the 99%Al{sub 2}O{sub 3} and 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} refractory systems by dissolving the respective refractories' matrix materials, which consist of fine Al{sub 2}O{sub 3} particles and an amorphous alumino-silicate phase. Due to enrichment in SiO{sub 2}, a network-former, infiltration into the 85%Al{sub 2}O{sub 3}–15%SiO{sub 2} system yielded a higher viscosity slag and hence, a shallower penetration depth. The results suggest that slag infiltration can be limited by interactions with the refractory through the formation of either a solid layer that physically impedes fluid flow or a more viscous slag that retards infiltration.

01 COAL, LIGNITE, AND PEAT↗

Normal and shear impact of layered composite with a crack - Dynamic stress intensification

The dynamic response of a layered composite under normal and shear impact is analyzed by assuming that the composite contains an initial flaw in the matrix material. One of the objectives was to develop an analytical method for determining dynamic stress solutions which should lead to a numerical method which utilizes Fourier transform for the space variable and Laplace transform for the time variable. The time-dependent angle loading is separated into two parts: a symmetric and a skew-symmetric with reference to the crack plane. By superposition, the transient boundary conditions consist of applying normal and shear tractions to a crack embedded in a layered composite; one phase of the composite could represent the fiber while the other could be the matrix. Mathematically, these conditions reduce the problem to a system of dual integral equations solved in the transform plane for the transform of the dynamic stress-intensity factor.

Sih, G. C.↗

Modeling 238U/204Pb (μ) and Initial Pb of Lunar Meteorite Northwest Africa 12593

Apatite Ca 5 (PO 4 ) 3 (F, Cl, OH) serves as a valuable analytical resource. It is the only nominally hydrous phase on the moon and possesses the capacity to concentrate elements like U, Th, Pb, and rare earth elements (REE). This characteristic facilitates its use in U-Pb and Pb-Pb geochronology, allowing for the determination of the initial isotopic Pb and the -238 U/ -204 Pb ratio (μ) of the parent melt. In situ analysis of apatite grains can provide a detailed record of geochemical changes, revealing the broader petrogenetic and volatile history of the source material. This mineral is particularly informative in understanding the developmental history of its source. In situ analyses are crucial for lunar samples, predominantly composed of breccias, where correlating distinct grains with whole rock analyses poses challenges. This study utilizes in situ apatite isotopic analysis of apatite grains in lunar meteorite Northwest Africa 12593 and model the initial Pb isotopic composition and -238 U/ -204 Pb (μ) of the source. We present in situ Secondary Ionization Mass Spectrometry (SIMS) Pb-Pb analyses of 12 apatite grains in Northwest Africa (NWA) 12593 to test two hypotheses: 1) NWA 12593 clasts and matrix are closely related and from the same source, and 2) the matrix material previously documented as having a highland affinity has a lower modeled μ then KREEP.

K M Lehman Franco↗

Inventory and Waste Characterization Status Report and OWL Update.

This report represents completion of milestone deliverable M2SF-18SNO10309013 "Inventory and Waste Characterization Status Report and OWL Update that reports on FY2018 activities for the work package (WP) SF-18SNO1030901. This report provides the detailed final information for completed FY2018 work activities for WP SF-18SN01030901, and a summary of priorities for FY2019. This status report on FY2018 activities includes evaluations of waste form characteristics and waste form performance models, updates to the OWL development, and descriptions of the two planned management processes for the OWL. Updates to the OWL include an updated user's guide, additions to the OWL database content for wastes and waste forms, results of the Beta testing and changes implemented from it. There are two processes being planned in FY2018, which will be implemented in FY2019. One process covers methods for interfacing with the DOE SNF DB (DOE 2007) at INL on the numerous entries for DOE managed SNF, and the other process covers the management of updates to, and version control/archiving of, the OWL database. In FY2018, we have pursued three studies to evaluate/redefine waste form characteristics and/or performance models. First characteristic isotopic ratios for various waste forms included in postclosure performance studies are being evaluated to delineate isotope ratio tags that quantitatively identify each particular waste form. This evaluation arose due to questions regarding the relative contributions of radionuclides from disparate waste forms in GDSA results, particularly, radionuclide contributions of DOE-managed SNF vs HLW glass. In our second study we are evaluating the bases of glass waste degradation rate models to the HIP calcine waste form. The HIP calcine may likely be a ceramic matrix material, with multiple ceramic phases with/without a glass phase. The ceramic phases are likely to have different degradation performance from the glass portion. The distribution of radionuclides among those various phases may also be a factor in the radionuclide release rates. Additionally, we have an ongoing investigation of the performance behavior of TRISO particle fuels and are developing a stochastic model for the degradation of those fuels that accounts for simultaneous corrosion of the silicon carbide (SiC) layer and radionuclide diffusion through it. The detailed model of the TRISO particles themselves, will be merged with models of the degradation behavior(s) of the graphite matrix (either prismatic compacts or spherical "pebbles") containing the particles and the hexagonal graphite elements holding the compacts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

AGR-3/4 Experiment Preliminary Mass Balance

AGR-3/4 was an experiment primarily aimed at studying fission product transport in graphite and graphitic materials. To accomplish this, 80 designed-to-fail (DTF) particles coated only with a thin pyrocarbon layer were incorporated among the roughly 7500 tristructural isotropic-coated driver fuel particles in each capsule. It was anticipated that intact DTF particles would behave like TRISO particles with SiC layer failures (releasing cesium and other metallic fission products to some extent, but retaining fission gases), and failed DTF particles would behave like TRISO particles with failed TRISO coatings (releasing both cesium and other metallic fission products and fission gases). The DTF particles provided a known source of fission products to migrate out into the fuel compact matrix and out into the surrounding concentric rings of graphite and graphitic matrix material for study. Post-irradiation examinations have focused on measuring the total releases of fission products from the fuel compacts (mass balance) and the spatial distribution of fission products in the rings. The total mass balance is an important parameter for comparison to fission product transport simulations of the AGR-3/4 experiment, and the spatial distribution within carbon rings is being used to derive fission product diffusion coefficients. To determine the fission product mass balance, each of the 12 irradiation capsules was disassembled, and their component parts analyzed via gamma counting and destructive leach or burn-leach methods. In “standard” capsules (Capsules 1, 3-5, 7-8, 10, and 12), inner rings, outer rings, sink rings, spacers, foils, felts, and through tubes were all analyzed for gamma-emitting fission products. Beta-emitting Sr-90 was measured as well, but because of the analysis program on the inner and outer rings, the Sr-90 inventory of the inner and outer rings is not yet available. “Fuel body” Capsules 2, 6, 9, and 11 were retained intact for future heating tests; thus, the inner and outer rings from these capsules were not measured. The most commonly detected radionuclide fission products were Ag-110m, Cs-134, Cs-137, Eu-154, Eu-155, and Sr-90. Sb-125 was also frequently detected in the sink rings and spacers; however, the zircaloy spacers used in Capsules 1 through 6 contained natural antimony that transmuted to Sb-125 and made it impossible to separate Sb-125 released from the fuel from that generated in the spacers. Summing the fission product inventory measured on each capsule component made it clear that the presence of 80 DTF particles in each capsule resulted in noticeably higher releases of cesium, europium, and strontium from AGR-3/4 fuel when compared to AGR-1 fuel which did not have DTF particles. Greater than 30 particles worth of Cs-134 was measured outside of the fuel compacts in Capsules 3-5, 7, 8, and 10. In Capsule 11 (an intact fuel body for which the inner and outer rings were not measured), 26 particle equivalents of Cs-134 was measured outside of the outer ring. Based on experience from AGR 1, it is very unlikely that any driver particles failed during the irradiation; therefore, this cesium is assumed to be overwhelmingly dominated by release from DTF particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Defining optimal enzyme and matrix combination for replating of human induced pluripotent stem cell-derived cardiomyocytes at different levels of maturity

Human induced pluripotent stem cell-derived cardiomyocytes (hiPSC-CM) create an unlimited cell source for basic and translational research. Depending on the maturity of cardiac cultures and the intended applications, obtaining hiPSC-CMs as a single-cell, monolayer or three-dimensional clusters can be challenging. Here, we defined strategies to replate hiPSC-CMs on early days (D15-30) or later more mature (D60-150) differentiation cultures. After generation of hiPSCs and derivation of cardiomyocytes, four dissociation reagents Collagenase A/B, Collagenase II, TrypLE, EDTA and five different extracellular matrix materials Laminin, iMatrix-511, Fibronectin, Matrigel, and Geltrex were comparatively evaluated by imaging, cell viability, and contraction analysis. For early cardiac differentiation cultures mimicking mostly the embryonic stage, the highest adhesion, cell viability, and beating frequencies were achieved by treatment with the TrypLE enzyme. Video-based contraction analysis demonstrated higher beating rates after replating compared to before treatment. For later differentiation days of more mature cardiac cultures, dissociation with EDTA and replating cells on Geltrex or Laminin-derivatives yielded better recovery. Cardiac clusters at various sizes were detected in several groups treated with collagenases. Collectively, our findings revealed the selection criteria of the dissociation approach and coating matrix for replating iPSC-CMs based on the maturity and the requirements of further downstream applications.

60 APPLIED LIFE SCIENCES↗

Influence of stress interaction on the behavior of off-axis unidirectional composites

The yield function for plane stress of a transversely isotropic composite lamina consisting of stiff, linearly elastic fibers and a von Mises matrix material is formulated in terms of Hill's elastic stress concentration factors and a single plastic constraint parameter. The above are subsequently evaluated on the basis of observed average lamina and constituent response for the Avco 5505 boron epoxy system. It is shown that inclusion of residual stresses in the yield function together with the incorporation of Dubey and Hillier's concept of generalized yield stress for anisotropic media in the constitutive equation correctly predicts the trends observed in experiments. The incorporation of the strong axial stress interaction necessary to predict the correct trends in the shear response is directly traced to the high residual axial stresses in the matrix induced during fabrication of the composite.

Pindera, M. J.↗

Investigating the Role of Incident Ion Flux in Solar Wind Space Weathering of Carbon-Rich Asteroidal Regolith Via H+ and He+ Irradiation of the Murchison Meteorite

We present results from a set of low and high flux 1 keV/amu H + and He + irradiation experiments performed on slabs of the Murchison CM2 carbonaceous chondrite. The low flux conditions for H + and He + irradiation were ~1-1.5 orders of magnitude lower than the high flux conditions, and each experiment was irradiated to a total fluence between ~3 × 10 16 to ~6 × 10 16 ions/cm 2 . Irradiation-induced changes in the surface chemistry and optical properties of the Murchison samples were evaluated using in situ X-ray photoelectron spectroscopy (XPS) and visible and near-infrared spectroscopy (VNIR). We characterized the microstructure and composition of ion damaged rims in focused ion beam (FIB) cross-sections extracted from olivine and matrix material in each irradiated Murchison slab using transmission electron microscopy (TEM). XPS results suggest that both low flux and high flux H + and He + irradiation cause minor sputtering of surface carbon as well as a reduction in the valence state of iron, from Fe 3+ to Fe 2+ . Slope bluing is observed in VNIR spectra of the irradiated samples which may reflect carbonization and dehydrogenation of organic species and contrasts with reddening trends associated with npFe 0 formation. Although we do not observe a strong flux-dependence on the crystallinity of ion-damaged olivine, TEM analyses reveal a variety of microstructures in all olivine FIB-sections, suggesting that crystallographic orientation affects amorphization efficiency. Analyses of matrix FIB-sections indicate that phyllosilicate alteration is mainly driven by He+ irradiation, where the higher incident flux leads to greater amorphization and the formation of more distinct ion-damaged layers, similar to smooth layers in returned Ryugu particles. TEM results also provide some evidence that higher ion flux leads to greater vesiculation, with He + irradiation being more efficient at vesiculation than H + irradiation, and that higher ion flux may promote the segregation of Mg and Si into laterally extensive lenses and layers in olivine samples. We discuss the implications of these findings for constraining the role that ion flux plays in the development of space weathering characteristics in silicate phases present in carbonaceous asteroidal regoliths. These results will be important for understanding the complexity of this process and how it operates on carbon-rich airless bodies like asteroids Bennu and Ryugu.

meteorites↗

FABRICATION OF URANIUM OXYCARBIDE KERNELS AND COMPACTS FOR HTR FUEL

As part of the program to demonstrate tristructural isotropic (TRISO)-coated fuel for the Next Generation Nuclear Plant (NGNP), Advanced Gas Reactor (AGR) fuel is being irradiation tested in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL). This testing has led to improved kernel fabrication techniques, the formation of TRISO fuel particles, and upgrades to the overcoating, compaction, and heat treatment processes. Combined, these improvements provide a fuel manufacturing process that meets the stringent requirements associated with testing in the AGR experimentation program. Researchers at Idaho National Laboratory (INL) are working in conjunction with a team from Babcock and Wilcox (B&W) and Oak Ridge National Laboratory (ORNL) to (a) improve the quality of uranium oxycarbide (UCO) fuel kernels, (b) deposit TRISO layers to produce a fuel that meets or exceeds the standard developed by German researches in the 1980s, and (c) develop a process to overcoat TRISO particles with the same matrix material, but applies it with water using equipment previously and successfully employed in the pharmaceutical industry. A primary goal of this work is to simplify the process, making it more robust and repeatable while relying less on operator technique than prior overcoating efforts. A secondary goal is to improve first-pass yields to greater than 95% through the use of established technology and equipment. In the first test, called “AGR-1,” graphite compacts containing approximately 300,000 coated particles were irradiated from December 2006 to November 2009. The AGR-1 fuel was designed to closely replicate many of the properties of German TRISO-coated particles, thought to be important for good fuel performance. No release of gaseous fission product, indicative of particle coating failure, was detected in the nearly 3-year irradiation to a peak burn up of 19.6% at a time-average temperature of 1038–1121°C. Before fabricating AGR-2 fuel, each fabrication process was improved and changed. Changes to the kernel fabrication process included replacing the carbon black powder feed with a surface-modified carbon slurry and shortening the sintering schedule. AGR-2 TRISO particles were produced in a 6-inch diameter coater using a charge size about 21-times that of the 2-inch diameter coater used to coat AGR-1 particles. The compacting process was changed to increase matrix density and throughput by increasing the temperature and pressure of pressing and using a different type of press. AGR-2 fuel began irradiation in the ATR in late spring 2010.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hot Structure Concepts and Materials for Space Exploration Project

Hot structures are multifunctional material systems that integrate the functions of thermal protection systems (TPS) and primary structure to increase mass efficiency in aerospace vehicles. The goal of this project was to improve our capabilities for developing lightweight, reusable, and reliable hot structures concepts to enable advanced space exploration missions. Specifically, current hot structure carbon/carbon (C/C) composite material systems have low interlaminar strength, which can lead to material failures at low load levels, and large material property variability in as-fabricated parts. Two parallel paths were followed to address these shortcomings. First, analysis models were developed to identify the conditions under which excessive interlaminar stresses occur and to evaluate the potential of stitching the C/C laminae to improve the interlaminar thermal-structural response. This effort included the development of high-fidelity, fracture-based thermal-structural finite element analysis models to evaluate critical features needed to produce efficient hot structure concepts. The second path focused on developing atomistic and mesoscale simulation tools to model the fabrication process in an effort to reduce the time and cost of production while improving the quality of the resulting parts. Aspects of the process currently being investigated include the infusion of the matrix precursor into the fiber preform, the cure of the precursor molecules into their polymeric form, and the carbonization and graphitization of the polymer to form the carbon matrix material. Results of the 6-month study are presented herein.

thermal↗

Fabricating Composite-Material Structures Containing SMA Ribbons

An improved method of designing and fabricating laminated composite-material (matrix/fiber) structures containing embedded shape-memory-alloy (SMA) actuators has been devised. Structures made by this method have repeatable, predictable properties, and fabrication processes can readily be automated. Such structures, denoted as shape-memory-alloy hybrid composite (SMAHC) structures, have been investigated for their potential to satisfy requirements to control the shapes or thermoelastic responses of themselves or of other structures into which they might be incorporated, or to control noise and vibrations. Much of the prior work on SMAHC structures has involved the use SMA wires embedded within matrices or within sleeves through parent structures. The disadvantages of using SMA wires as the embedded actuators include (1) complexity of fabrication procedures because of the relatively large numbers of actuators usually needed; (2) sensitivity to actuator/ matrix interface flaws because voids can be of significant size, relative to wires; (3) relatively high rates of breakage of actuators during curing of matrix materials because of sensitivity to stress concentrations at mechanical restraints; and (4) difficulty of achieving desirable overall volume fractions of SMA wires when trying to optimize the integration of the wires by placing them in selected layers only.

Turner, Travis L.↗

Rigid Oligomer from Lignin in Designing of Tough, Self-Healing Elastomers

Here, converting lignin into well-defined compounds is often challenged by structural complexation and inorganic contamination induced by the pulping process. In this report, instead of breaking down lignin into small molecules, we extracted a uniform and rigid oligomer from the lignin waste stream. The multifunctional polyphenol oligomer containing carboxylic acid, alcohol, and phenol groups is highly reactive and brings stiffness into the material matrix. Tough and self-healing elastomers are economically prepared from this oligomer by a reaction with epoxy-terminated polyethylene glycol, without needing any solvent. Specifically, the polyaromatic backbone’s rigidity enhances the elastomer’s toughness, and the multiple polar substituents form a network of hydrogen bonding that heals the elastomer. Many other applications, including adhesives, hydrogels, coating, and metal scavengers, are envisioned based on this oligomer’s unique properties.

36 MATERIALS SCIENCE↗