Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MARTENSITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Transition from the twinning induced plasticity to the γ-ε transformation induced plasticity in a high manganese steel

Neutron-diffraction investigation on the deformation of a Fe-18Mn-3Si-0.6C-0.4Al steel reveals that the twinning is mainly dominant at a stress below 900 MPa, above which the twinning behavior is largely outweighed by phase transformation from the face-centered-cubic (FCC) γ-austenite to the hexagonal-close-packed (HCP) ε-martensite. In the deformed grains, the distribution of ε-martensite is parallel with the twin boundary. Both the well-known {111} γ //{0001} ε relationship and an additional {111} γ //{11–21} ε orientation relation were identified. After the phase transformation, both phases deformed further with the lattice rotating around an axis perpendicular to the tensile direction. Transition from the twinning dominant behavior to the phase transformation induced plasticity effect is explained by the grain orientation dependence of the effective stacking fault energy (ESFE). An asymmetric and inverse relationship between the width of stacking faults (SF) and the ESFE is obtained from the density functional theory (DFT). The tensile stress always increases proportionally with the SF width in the twinning favorable grains and thus a decreasing ESFE. The replacement of twinning activities by phase transformation could be due to both the nucleation site of ε-martensite at the SF of the twin boundary and the decrease of the ESFE in grains which originally favors the twinning.

Materials Science↗

Enhancing fatigue life by ductile-transformable multicomponent B2 precipitates in a high-entropy alloy

Catastrophic accidents caused by fatigue failures often occur in engineering structures. Thus, a fundamental understanding of cyclic-deformation and fatigue-failure mechanisms is critical for the development of fatigue-resistant structural materials. Here we report a high-entropy alloy with enhanced fatigue life by ductile-transformable multicomponent B2 precipitates. Its cyclic-deformation mechanisms are revealed by real-time in-situ neutron diffraction, transmission-electron microscopy, crystal-plasticity modeling, and Monte-Carlo simulations. Multiple cyclic-deformation mechanisms, including dislocation slips, precipitation strengthening, deformation twinning, and reversible martensitic phase transformation, are observed in the studied high-entropy alloy. Its improved fatigue performance at low strain amplitudes, i.e., the high fatigue-crack-initiation resistance, is attributed to the high elasticity, plastic deformability, and martensitic transformation of the B2-strengthening phase. This study shows that fatigue-resistant alloys can be developed by incorporating strengthening ductile-transformable multicomponent intermetallic phases.

36 MATERIALS SCIENCE↗

Transformation enabled nitride magnets absent rare earths and a process of making the same

A process for producing an ordered martensitic iron nitride powder that is suitable for use as a permanent magnetic material is provided. The process includes fabricating an iron alloy powder having a desired composition and uniformity; nitriding the iron alloy powder by contacting the material with a nitrogen source in a fluidized bed reactor to produce a nitride iron powder; transforming the nitride iron powder to a disordered martensitic phase; annealing the disordered martensitic phase to an ordered martensitic phase; and separating the ordered martensitic phase from the iron nitride powder to yield an ordered martensitic iron nitride powder.

36 MATERIALS SCIENCE↗

Transformation enabled nitride magnets absent rare earths and a process of making the same

A process for producing an ordered martensitic iron nitride powder that is suitable for use as a permanent magnetic material is provided. The process includes fabricating an iron alloy powder having a desired composition and uniformity; nitriding the iron alloy powder by contacting the material with a nitrogen source in a fluidized bed reactor to produce a nitride iron powder; transforming the nitride iron powder to a disordered martensitic phase; annealing the disordered martensitic phase to an ordered martensitic phase; and separating the ordered martensitic phase from the iron nitride powder to yield an ordered martensitic iron nitride powder.

Matthiesen, David↗

Nanoengineered Hypereutectoid Steel with Superior Hardness and Wear Resistance

Hypereutectoid SAE 52100 steel is extensively used in bearing applications. Microstructure modification in terms of dislocation martensite and carbide refinement was achieved for SAE 52100 steel through a simple duplex heat treatment. Refinement of prior austenite grains to less than 5 μm resulted in the conversion of conventional high-carbon twinned martensite to dislocation martensite. The concurrent refinement of austenite grains and carbide precipitates was accomplished by high-temperature austenitization followed by low-temperature tempering. This resulted in nanoscale nonstoichiometric ε-carbides within a heavily twinned martensitic structure. These nanoscale carbides acted as grain boundary pinning agents after their transformation to θ-carbides during the final austenitization process. The resulting microstructure was characterized by a fine dispersion of θ-carbides within dislocation martensite and showed roughly 24% increase in tensile strength and 30% better wear resistance compared to conventional structure.

36 MATERIALS SCIENCE↗

Tempering kinetics during multilayer laser additive manufacturing of a ferritic steel

Grade 91 steel forms martensite during additive manufacturing and the extent of tempering of martensite significantly affects the mechanical properties of parts. Currently, there is a lack of quantitative understanding of the tempering kinetics for Grade 91 steel, and as a result, the effects of repeated thermal cycles on properties for different processing conditions cannot be determined. Here we evaluate the tempering kinetics by determining the constant terms in the Johnson Mehl Avrami kinetic equation from the tempering data available in the literature and the thermal cycles computed using a rigorously-tested heat and fluid flow model of multi-layer additive manufacturing. The raw tempering data are cleaned using a neural network to enhance accuracy. The lower layers experience repeating cycles of heating and cooling when the upper layers are added. As a result, the hardness is reduced owing to the tempering of martensite. In contrast, martensite formed in the upper layers is not tempered to the same extent and the hardness remains high. Therefore, the hardness of the part increases with the distance from the substrate. Variations in the heat input at different laser powers and scanning speeds significantly affect the extent of tempering. Finally, since the method used here can provide a quantitative understanding of the tempering of martensite and the spatial variation in hardness, it can be used to tailor the microstructure and hardness of heat treatable printed metallic parts.

36 MATERIALS SCIENCE↗

Premartensite transition in Ni{sub 2}FeGa Heusler alloy

Martensitic phase transformation of Ni{sub 2}FeGa Heusler alloy was studied by differential scanning calorimetry. Atomic ordering induced in the austenite structure by quenching from high temperature plays a significant role on martensitic phase transformation. Higher magnetization and larger magneto-crystalline anisotropy of martensite phase than that of austenite phase are noticed. Tweed contrast regions observed in the transmission electron microscopy were correlated to premartensite phenomena. A shift in premartensitic transition temperature prior to martensitic transformation as measured by differential scanning calorimetry is being reported for the first time in this system. - Highlights: • Atomic ordering influences martensitic transformation in Ni{sub 2}FeGa Heusler alloy. • Observation of tweed contrast in TEM was correlated to premartensite phenomena. • For the first time the shift in premartensite peak was observed in DSC.

36 MATERIALS SCIENCE↗

Microstructure and phase composition characterization in a Co{sub 38}Ni{sub 33}Al{sub 29} ferromagnetic shape memory alloy

Transmission electron microscopy was performed to investigate the microstructures of a secondary phase and its surrounding matrix in a Co{sub 38}Ni{sub 33}Al{sub 29} ferromagnetic shape memory alloy. The secondary phase shows a γ′ L1{sub 2} structure exhibiting a dendritic morphology with enclosed B2 austenite regions while the matrix shows the L1{sub 0} martensitic structure. A secondary phase-austenite-martensite sandwich structure with residual austenite ranging from several hundred nanometers to several micrometers wide is observed at the secondary phase-martensite interface due to the depletion of Co and enrichment of Al in the chemical gradient zone and the effect of the strong martensitic start temperature dependency of the element concentrations. The crystallographic orientation relationship of the secondary phase and the B2 austenite fits the Kurdjumov-Sachs relationship. - Highlights: •The secondary phase has a γ′ L1{sub 2} structure exhibiting a dendritic morphology. •A secondary phase-austenite-martensite sandwich structure is observed. •The structural sandwich structure is due to elemental composition variation. •The secondary phase and the B2 austenite fit the Kurdjumov-Sachs relationship.

36 MATERIALS SCIENCE↗

Phase structures and morphologies of tempered CA6NM stainless steel welded by hybrid laser-arc process

The post-weld tempered microstructure of hybrid laser-arc welded CA6NM, a cast low carbon martensitic stainless steel, was investigated. The microstructural evolutions from the fusion zone to the base metal were characterized in detail using optical microscopy, scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), X-ray diffraction (XRD) and microhardness techniques. The fusion zone, in its post-weld tempered condition, consisted of tempered lath martensite, residual delta-ferrite with various morphologies, reversed austenite and chromium carbides. The reversed austenite, which can be detected through both EBSD and XRD techniques, was found to be finely dispersed along the martensite lath boundaries, particularly at triple junctions. Based on the EBSD analysis, the orientation relationship between the reversed austenite and the adjacent martensite laths seemed to follow the Kurdjumov-Sachs (K-S) model. The results also revealed the presence of the reversed austenite in the different regions of the heat affected zone after post-weld tempering. The microindentation hardness distribution was measured, and correlated to the evolution of the corresponding microstructure across the welds. - Highlights: •The EBSD analysis was performed on hybrid laser-arc welded CA6NM. •The FZ consisted of tempered lath martensite, reversed austenite, carbides and δ ferrite after tempering. •The reversed γ was formed along the α′ lath boundaries, particularly at triple junctions.

36 MATERIALS SCIENCE↗

In-situ high-energy x-ray diffuse-scattering study of the phase transition of Ni{sub 2}MnGa single crystal under high magnetic field.

The defects-related microstructural features connected to the premartensitic and martensitic transition of a Ni{sub 2}MnGa single crystal under a high magnetic field of 50 KOe applied along the [1{bar 1}0] crystallographic direction of the Heusler phase were studied by the in-situ high-energy X-ray diffuse-scattering experiments on the high energy synchrotron beam line 11-ID-C of APS and thermomagnetization measurements. Our experiments show that a magnetic field of 50 KOe applied along the [1{bar 1}0] direction of the parent Heusler phase can promote the premartensitic transition of Ni{sub 2}MnGa single crystal, but puts off martensite transition and the reverse transition. The premartensitic transition temperature (T{sub PM}) increases from 233 to 250 K (-40 to -23 C). The martensite transition start temperature (M{sub s}) decreases from 175 to 172 K (-98 to -101 C), while the reverse transition start temperature (A{sub s}) increases from 186 to 189 K (-87 to -84 C). The high magnetic field leads to a rapid rearrangement of martensite variants below the martensite transition finish temperature (M{sub f}). The real transition process of Ni{sub 2}MnGa single crystal under the high magnetic field was in-situ traced.

43 PARTICLE ACCELERATORS↗

An assessment of the contributing factors to the superior properties of a nanostructured steel using in situ high-energy x-ray diffraction.

In contrast to most nanostructured materials, outstanding mechanical property has been demonstrated in a nanostructured metastable austenitic steel, owing to the new characteristics of deformation-induced martensitic transformation. In this paper, by employing an in situ high-energy X-ray diffraction technique, we explore these characteristics by examining factors from the load partitioning, Lueders banding, to texture development. It was found that the martensitic transformation was mainly driven through Lueders band propagation. Marked load transfer takes place from austenite to martensite as Lueders band propagates, and continues into the homogeneous deformation regime. The texture development is mostly contributed by martensitic transformation, but dislocation-based plasticity also plays a role. The effective load partitioning along with the deformability of martensite promotes sample ductility.

36 MATERIALS SCIENCE↗

Transformation-induced plasticity in bulk metallic glass composites evidenced by in-situ neutron diffraction

Transformation-induced plasticity in a strain-softening amorphous matrix consisting of austenite B2 phase was studied by in-situ neutron diffraction, coupled with molecular dynamic simulation. It was found that the martensitic transformation from B2 to B19' upon loading commenced at the macroscopic yielding which increased with the decrease of the fraction of the parent austenite B2 phase, and the threshold lattice strain for the martensitic transformation is almost the same in different samples, suggesting that the martensitic transformation in the current glassy matrix is strain-controlled. Analysis of load partition and strain accommodation unveiled that B2 has elastic anisotropy, and the desirable elastic match between B2 and the amorphous matrix ensures a good cooperative deformation. Additionally, molecular dynamic simulation revealed that atoms at the interface between B2 and the amorphous matrix deviated from the standard B2 lattices and acted as nucleation site for the martensitic transformation, eventually giving rise to the strain-controlled martensitic transformation. Our findings provide new insights into the mechanism of phase transformation-mediated plasticity at the microscopic level, and have useful implications for developing novel, high-performance bulk metallic glass composites.

36 MATERIALS SCIENCE↗

In situ synchrotron X-ray diffraction investigations of the physical mechanism of ultra-low strain hardening in Ti-30Zr-10Nb alloy

A warm-rolled, metastable beta-type Ti-30Zr-10Nb alloy exhibited a peculiar two-stage yielding behavior under uniaxial tensile loading, showing a first plastic stage with obvious strain hardening at 0.4%-10.4% strain and a second plastic stage with ultra-low strain hardening at 10.4%-23.5% strain. In situ high-energy X-ray diffraction (HE-XRD) was used to reveal the stress-induced martensitic transformation scenarios and physical mechanism of the different strain hardening rates. It was found that the deformation-induced phase transformation dominated the onset of the first plastic stage corresponding to the selection of favorable martensitic variants, and their elastic interaction contributed to the obvious strain hardening. HE-XRD experiments further verified that the ultra-low strain hardening rate in the second plastic stage was related to an interesting superelasticity of the martensite, which was characterized by the reversible, stress-induced reorientation of the martensite variants. This reorientation of the martensite variants was primarily due to the rigid lattice rotation of similar to 23 degrees about the [110](α '') axis toward the tensile direction. Here, our investigations provide in-depth understanding of the mechanism of the excellent plasticity with ultra-low strain hardening in beta-type titanium alloys.

36 MATERIALS SCIENCE↗

Fabrication, microstructure and mechanical properties of W-NiTi composites

Here, new two-phase tungsten-based composites containing 88 wt% tungsten powders and 12 wt% nearly equiatomic NiTi alloy deforming by martensite variant detwinning were fabricated by infiltration and hot pressing in this study. The change of Ti/Ni ratio in NiTi mater alloy and the effect of addition of Nb element on the microstructure, martensitic transformation and mechanical properties of W-NiTi composites were investigated by comparison of W-Ni 50 Ti 50 , W-Ni 44 Ti 56 , W-Ni 42 Ti 58 and W-Ni 42 Ti 53 Nb 5 composites. The results showed that brittle Ni 3 Ti formed in the W-Ni 50 Ti 50 and W-Ni 44 Ti 56 composites and brittle Ti 2 Ni formed in the W-Ni 42 Ti 58 composites while no brittle intermetallics formed in the W-Ni 42 Ti 53 Nb 5 composite. The W-Ni 42 Ti 53 Nb 5 composite exhibited the sharpest martensitic transformation with the largest transformation enthalpy among the four different composites. The W-Ni 42 Ti 53 Nb 5 composite exhibited a double-yielding phenomenon under compression with an ultimate compressive strength of 3820 MPa and a deformation of 50.4%. In-situ synchrotron high-energy Xray diffraction measurements revealed the first yielding was caused by the martensite reorientation of the NiTi matrix and the second was due to the commencement of massive plastic deformation of the reoriented martensite and is also attributed to the microscopic internal fracturing of the W particles.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of a Ti-microalloyed low-carbon stainless steel treated by quenching-partitioning-tempering process

Quenching-partitioning-tempering (Q-P-T) process was used to treat a Ti-microalloyed low-carbon stainless steel after cold rolling. In addition to martensite, ferrite and retained austenite, TiN, coarse TiC, fine TiC, (Fe,Cr){sub 3}C and ultra-fine TiC precipitates were formed after the Q-P-T treatment. Based on field emission-scanning electron microscope (FESEM) and transmission electron microscope (TEM) observations, thermodynamic, crystallographic and statistical analyses were used to reveal the precipitation behaviors of these particles. The effects of partitioning-tempering (P-T) temperature and time on the microstructure and mechanical properties of Q-P-T treated specimens were specially studied. The coarsening and spheroidization of (Fe,Cr){sub 3}C particles during P-T stage were obviously retarded by large Cr addition. The retained austenite was obtained significantly with appropriate P-T parameters. The precipitation of ultra-fine TiC particles in the martensite during the P-T stage at 500 °C induced a secondary hardening. - Highlights: • Some fine TiC with 30–70 nm precipitated in austenite during partial austenization. • A part of fine TiC had K-S OR with martensite after Q-P-T treatment. • A part of fine TiC had a OR specially deviating from K-S OR with martensite. • Coarsening and spheroidization of (Fe,Cr){sub 3}C were retarded during P-T stage. • Ultra-fine TiC with < 10 nm precipitated in martensite during P-T stage at 500 °C.

36 MATERIALS SCIENCE↗

In-situ EBSD study of deformation behavior of retained austenite in a low-carbon quenching and partitioning steel via uniaxial tensile tests

Through using in-situ electron back-scattered diffraction and uniaxial tensile tests, this work mainly focuses on the deformation behavior of retained austenite (RA) in a low-carbon quenching and partitioning (Q&P) steel. In this paper, three different types of RA can be distinguished from different locations, respectively, RA grains at the triple edges, twinned austenite and RA grains positioned between martensite. The results have shown that grains at the triple edges and twinned austenite could transform easily with increasing strain, i.e. are less stable when compared with RA grains distributed between martensite that could resist a larger plastic deformation. Meanwhile, the strain leads to rotations of RA grains distributed at the triple edges and between martensite. Moreover, RA grains with a similar orientation undergone similar rotations with the same true strain. These RA grains rotated along a specific slip plane and slip direction and the grain rotation is taken as a significant factor to improve the ductility of steel. In addition, grain sizes of RA decreased gradually with an increase of true strain and smaller (0–0.2 μm) grains were more capable of resisting the deformation. According to kernel average misorientation (KAM) analysis, it can be found that strain distribution is preferentially localized near martensite–austenite phase boundaries and in the interior of martensite. The average KAM values increased continuously with increasing true strain. - Highlights: •The in-situ and ex-situ tensile specimens differ to some extent in mechanical properties. •Retained austenite grains at the triple edges and twinned austenite transformed easily at the early stage of true strain. •Film-like retained austenite grains only rotated prior to the transformation during straining. •Retained austenite grains having with a similar orientation experienced similar rotations during the same true strain.

36 MATERIALS SCIENCE↗

Electron backscatter and X-ray diffraction studies on the deformation and annealing textures of austenitic stainless steel 310S

We studied the texture evolution of thermo-mechanically processed austenitic stainless steel 310S. This alloy was cold rolled up to 90% reduction in thickness and subsequently annealed at 1050 °C. At the early stages of deformation, strain-induced martensite was formed from deformed austenite. By increasing the deformation level, slip mechanism was found to be insufficient to accommodate higher deformation strains. Our results demonstrated that twinning is the dominant deformation mechanism at higher deformation levels. Results also showed that cold rolling in unidirectional and cross rolling modes results in Goss/Brass and Brass dominant textures in deformed samples, respectively. Similar texture components are observed after annealing. Thus, the annealing texture was greatly affected by texture of the deformed parent phase and martensite did not contribute as it showed an athermal reversion during annealing. Results also showed that when the fraction of martensite exceeds a critical point, its grain boundaries impeded the movement of austenite grain boundaries during annealing. As a result, recrystallization incubation time would increase. This caused an incomplete recrystallization of highly deformed samples, which led to a rational drop in the intensity of the texture components. - Highlights: •Thermo-mechanical processing through different cold rolling modes can induce different textures. •Martensite reversion is athermal during annealing. •Higher fraction of deformation-induced martensite can increase the annealing time required for complete recrystallization. •Annealing texture is mainly influenced by the deformation texture of austenite.

36 MATERIALS SCIENCE↗

A study of microstructural evolution of Fe-18Cr-8Ni, Fe-17Cr-12Ni, and Fe-20Cr-25Ni stainless steels after mechanical alloying and annealing

In this study, high-energy mechanical alloying technique was used to produce nanocrystalline stainless steels of three different compositions from elemental powders. The microstructural evolution (grain growth and phase transformation) as a function of alloy compositions and annealing temperatures were investigated by room and high temperature x-ray diffraction experiments, transmission electron microscopy and focused ion beam microscopy. The results revealed that stainless steels with low nickel content (i.e., Fe-18Cr-8Ni) underwent a deformation-induced martensitic transformation during room temperature mechanical alloying. Deformation-induced martensitic transformation with increasing nickel content (i.e., Fe-17Cr-12Ni and Fe-20Cr-25Ni) would not be possible by room temperature milling but was created by high strain rate cryogenic processing, the degree to which was compositional dependent. Post process annealing induced the reverse transformation from martensite-to-austenite the ratio of which was found to be a factor of alloy composition and annealing temperature. The real time in-situ x-ray studies showed that the martensite-to-austenite reverse transformation was completed at around 600 °C and 800 °C for Fe-18Cr-8Ni and Fe-20Cr-25Ni steels, respectively. Microscopy studies revealed a significant enhancement in the resistance to grain growth for Fe-17Cr-12Ni steel over other compositions at elevated temperatures as high as 1200 °C. As such, cryogenic processing following by reverse martensitic transformation of high Ni containing alloys provides a pathway for developing higher heat resistant stainless steel alloys.

36 MATERIALS SCIENCE↗