Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Knowledge Transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Accommodation of Silicon in an Interconnected Copper Network for Robust Li-Ion Storage

Silicon (Si)-based materials are one of the most promising anodes to be applied in rechargeable lithium ion batteries. However, the active Si/electrolyte interface causes continuous side reactions and poor conductivity, which significantly decreases the cycling stability. Cu is the only metallic current collector that has been known to promote electron conduction and lithium-ion transfer without alloying reaction occurrence. However, to the best current knowledge, scalable interface engineering incorporating Cu has not been reported. In this study, this conductive Cu interface (CCI) is constructed through a self-assembly carbothermic reduction method to achieve efficient protection of Si/electrolyte interfaces while allowing for fast Li + diffusion. The energy barrier of lithium-ion diffusion through Cu is calculated to be 0.1965 eV, which is much lower than that through Au, Fe, and Ni films. Benefiting from the enhanced interfacial protection and kinetics of Si with CCI, a fading rate of only 0.068% is maintained for 1000 cycles and an aerial capacity of 4.78 mAh cm -2 is achieved after 280 cycles, which is comparable to the industry standards required for practical application.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Stable Unassisted Solar Water Splitting on Semiconductor Photocathodes Protected by Multifunctional GaN Nanostructures

Producing hydrogen by unassisted solar water splitting is one essential step to make direct solar fuel conversion a viable energy source. To date, however, there has been no demonstration of stable photoelectrodes for high efficiency photoelectrochemical water splitting. In this work, we report that a GaInP2/GaAs/Ge triple-junction (3J) photocathode protected by multi-functional GaN nanostructures can enable both efficient and relatively stable solar water splitting. A 12.6% solar-to-hydrogen (STH) efficiency is measured without any external bias. Of particular importance, we demonstrate relatively stable solar water splitting for 80 hours in three-electrode configuration and 57 hours in two-electrode measurement at zero bias. This is the best reported stability for multi-junction semiconductor photocathodes in two-electrode configuration to our knowledge. Here, the multifunctional GaN nanostructure significantly reduces the charge transfer resistance at semiconductor/electrolyte interface and protects III-V materials against corrosion. Such multi-functional GaN photocatalytic nanostructures provide a new pathway to improve the performance of conventional photoelectrodes to achieve both efficient and stable unassisted solar water splitting.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Planck 2013 results. IV. Low Frequency Instrument beams and window functions

This paper presents the characterization of the in-flight beams, the beam window functions, and the associated uncertainties for the Planck Low Frequency Instrument (LFI). Knowledge of the beam profiles is necessary for determining the transfer function to go from the observed to the actual sky anisotropy power spectrum. The main beam distortions affect the beam window function, complicating the reconstruction of the anisotropy power spectrum at high multipoles, whereas the sidelobes affect the low and intermediate multipoles. The in-flight assessment of the LFI main beams relies on the measurements performed during Jupiter observations. By stacking the datafrom multiple Jupiter transits, the main beam profiles are measured down to-20 dB at 30 and 44 GHz, and down to-25 dB at 70 GHz. The main beam solid angles are determined to better than 0.2% at each LFI frequency band. The Planck pre-launch optical model is conveniently tuned to characterize the main beams independently of any noise effects. This approach provides an optical model whose beams fully reproduce the measurements in the main beam region, but also allows a description of the beams at power levels lower than can be achieved by the Jupiter measurements themselves. The agreement between the simulated beams and the measured beams is better than 1% at each LFI frequency band. The simulated beams are used for the computation of the window functions for the effective beams. The error budget for the window functions is estimated from both main beam and sidelobe contributions, and accounts for the radiometer bandshapes. The total uncertainties in the effective beam window functions are: 2% and 1.2% at 30 and 44 GHz, respectively (at ℓ ≈ 600), and 0.7% at 70 GHz (at ℓ ≈ 1000).

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1974

Effect of Various Material Properties on the Adhesive Stage of Fretting

Various properties of metals and alloys were studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films were found to influence adhesion. High atomic density, low surface energy grain orientations exhibited lower adhesion than other orientations. Knowledge of interfacial surface binding energies assists in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents accomplishes both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗
NASA NTRS1980

The role of satellite altimetry in climate studies

The results of three generations of satellite-borne radar altimetry experiments are summarized. The diverse measurements possible from this instrument are shown to be directly applicable to studies of the importance of the oceans in climate. The radar altimeter has unique value for investigations seeking knowledge of the interconnections between ocean dynamics, heat and momentum transfer across the air-sea interface, sea ice extent, and polar ice sheet thickness.

Parsons, C. L.↗
NASA NTRS1987

Pinhole occulter experiment

Viewgraphs and charts from a briefing summarize the accomplishments, results, conclusions, and recommendations of a feasibility study using the Pinhole Occulter Facility (POF). Accomplishments for 1986 include: (1) improved IPS Gimbal Model; (2) improved Crew Motion Disturbance Model; (3) use of existing shuttle on-orbit simulation to study the effects of orbiter attitude deadband size on POF performance; (4) increased understanding of maximum performance expected from current actuator/sensor set; (5) use of TREETOPS nonlinear time domain program to obtain system dynamics describing the complex multibody flexible structures; (6) use of HONEY-X design tool to design and evaluate multivariable compensator for stability, robustness, and performance; (7) application of state-of-the-art compensator design methodology Linear Quadratic Gaussian/Loop Transfer Recovery (LQG/LTR); and (8) examination of tolerance required on knowledge of the POF boom flexible mode frequencies to insure stability, using structure uncertainty analysis.

Ring, Jeff↗
NASA NTRS2006

Centaur Test Bed (CTB) for Cryogenic Fluid Management

Future missions such as NASA s space exploration vision and DOD satellite servicing will require significant increases in the understanding and knowledge of space based cryogenic fluid management (CFM), including the transfer and storage of cryogenic fluids. Existing CFM capabilities are based on flight of upper stage cryogenic vehicles, scientific dewars, a few dedicated flight demonstrations and ground testing. This current capability is inadequate to support development of the CEV cryogenic propulsion system, other aspects of robust space exploration or the refueling of satellite cryo propulsion systems with reasonable risk. In addition, these technologies can provide significant performance increases for missions beyond low-earth orbit to enable manned missions to the Moon and beyond. The Centaur upper-stage vehicle can provide a low cost test platform for performing numerous flight demonstrations of the full breadth of required CFM technologies to support CEV development. These flight demonstrations can be performed as secondary mission objectives using excess LH2 and/or LO2 from the main vehicle propellant tanks following primary spacecraft separation at minimal cost and risk.

Sakla, Steven↗
DOE OSTI2023

Dedication to James A. Miller

This special memorial issue pays tribute to James (Jim) A. Miller, a giant of combustion science who died in 2021, with a celebration of his enormous influence on the field. We were touched by the responses we received after we sent out the invitations for it. Jim inspired several generations of scientists, who viewed him as a mentor, a father figure, and a friend. Together with Nils Hansen and Peter Glarborg, we have written a detailed account on his life and work. Furthermore, it appeared in this journal shortly after his death; and so here we focus on the scientific areas he had interest in and influence on, and how they relate to the 34 papers in this issue. The topics of these papers span a variety of Jim's interests including nitrogen chemistry, polycyclic aromatic hydrocarbon (PAH) chemistry, oxidation chemistry, energy transfer, prompt dissociations, and codes to facilitate combustion chemistry simulations.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
DOE OSTI2020

A Radiative Transfer Model for Patchy Landscapes Based on Stochastic Radiative Transfer Theory

The availability of global high-resolution land cover maps provides promising a priori knowledge for characterizing subpixel heterogeneity and improving predictions of directional reflectance of coarse-resolution pixels. Due to mutual shadowing and sheltering effects between the adjacent forest and cropland patches, the spectral nonlinear mixing of patchy ecotones is significant, especially when the sun illuminates the ecotone from the forest side with high solar zenith angle. The spectral linear mixture (SLM) approach leads to overestimation of the bidirectional reflectance factor (BRF) in the red band in the principal plane (PP), with a maximum absolute error (MAE) of 0.0063 and a maximum relative error (MRE) of 52.5%, and to underestimation in the near-infrared band in PP with an MAE of 0.0940 and an MRE of 14.5%. In a scenario with randomly distributed boundary orientations, the overestimation of SLM increases with the degree of fragmentation and the view zenith angle. We propose a Radiative Transfer model for patchy ECotones (RTEC). which improves R² from 0.61 to 0.94 in the red band of Landsat-8 directional reflectance at the validation site. The RTEC model provides an efficient and analytical approach for directional reflectance predictions over heterogeneous patchy landscapes at coarse resolution and will be used for biophysical parameter retrievals [e.g., the leaf area index (LAI)] in future applications.

Zeng, Yelu↗
DOE OSTI2017

Interface-induced phenomena in magnetism

Our article reviews static and dynamic interfacial effects in magnetism, focusing on interfacially-driven magnetic effects and phenomena associated with spin-orbit coupling and intrinsic symmetry breaking at interfaces. It provides a historical background and literature survey, but focuses on recent progress, identifying the most exciting new scientific results and pointing to promising future research directions. It starts with an introduction and overview of how basic magnetic properties are affected by interfaces, then turns to a discussion of charge and spin transport through and near interfaces and how these can be used to control the properties of the magnetic layer. Important concepts include spin accumulation, spin currents, spin transfer torque, and spin pumping. We provide an overview for the current state of knowledge and existing review literature on interfacial effects such as exchange bias, exchange spring magnets, spin Hall effect, oxide heterostructures, and topological insulators. Our article highlights recent discoveries of interface-induced magnetism and non-collinear spin textures, non-linear dynamics including spin torque transfer and magnetization reversal induced by interfaces, and interfacial effects in ultrafast magnetization processes.

36 MATERIALS SCIENCE↗
NASA NTRS2021

A Practical Guide to Writing a Radiative Transfer Code

Using our decades-long experience in radiative transfer (RT) code development for Earth science, we endeavor to reduce the knowledge gap of bringing RT from theory to code quickly. Despite numerous classic and recent literature, it is still hard to develop anRT code from scratch within a few weeks. It is equally hard to understand, not to mention modify, an existing “monster” RT code, for which the developer is either located remotely or has retired. Following the format of “Numerical Recipes” by Press et al., we collocate in this paper small pieces of necessary theory with corresponding small pieces of RT code. These are arranged in an order that is natural for code development, which is often opposite of the natural order for laying out the theoretical basis. We focus on the transfer of unpolarized monochromatic solar radiation in a plane-parallel atmosphere over a reflecting surface. Both the surface and the atmosphere are homogeneous (uniform) at all directions. The multiple scattering is numerically solved using the deterministic method of Gauss-Seidel iterations. Except for the presented Python-Numba open-source RT code gsit, the paper does not report any new scientific results, but rather serves as an academic demonstration. If development time is an issue or the reader is familiar with basic concepts of RT theory, we recommend proceeding directly to Sec.3 “RT code development.

multiple light scattering↗
NASA NTRS2015

Convective Enhancement of Icing Roughness Elements in Stagnation Region Flows

To improve existing ice accretion simulation codes, more data regarding ice roughness and its effects on convective heat transfer are required. To build on existing research on this topic, this study used the Vertical Icing Studies Tunnel (VIST) at NASA Glenn Research to model realistic ice roughness in the stagnation region of a NACA 0012 airfoil. Using the VIST, a test plate representing the leading 2% chord of the airfoil was subjected to flows of 7.62 m/s (25 ft/s), 12.19 m/s (40 ft/s), and 16.76 m/s (55 ft/s). The test plate was fitted with 3 surfaces, each with a different representation of ice roughness: 1) a control surface with no ice roughness, 2) a surface with ice roughness with element height scaled by 10x and streamwise rough zone width from the stagnation point scaled by 10x, and 3) a surface with ice roughness with element height scaled by 10x and streamwise rough zone width from the stagnation point scaled by 25x. Temperature data from the tests were recorded using an infrared camera and thermocouples imbedded in the test plate. From the temperature data, a convective heat transfer coefficient map was created for each case. Additional testing was also performed to validate the VIST's flow quality. These tests included five-hole probe and hot-wire probe velocity traces to provide flow visualization and to study boundary layer formation on the various test surfaces. The knowledge gained during the experiments will help improve ice accretion codes by providing heat transfer coefficient validation data and by providing flow visualization data helping understand current and future experiments performed in the VIST.

Icing↗
DOE OSTI2016

Improved Understanding toward Sliding Bubble Effect on Wall Heat Transfer in Subcooled Boiling Flow

The significance of bubble sliding on wall heat transfer under boiling and condensing conditions has consistently been reported by previous researchers, causing increasing attention within boiling heat transfer community. The authors' recent work for subcooled flow boiling experiment, also clearly shows the strong influence of sliding bubbles in wall heat transfer. However, despite the importance as well as the interest for the sliding bubbles both in experiment and CFD modelling, the mechanism of wall heat transfer induced by sliding bubbles has still barely been known. This mainly results from the fact that proper experimental data and physical insight based on them are largely lacking. This paper presents the authors' work to improve the insight toward the wall heat transfer mechanism associated with sliding bubbles. In particular, effort has been dedicated to identifying the knowledge gap between the actual physics and the CFD boiling models. Specifically, of major interest is the 'wall area of bubble influence' which is one of the important factors considered in most wall heat flux partitioning models to evaluate the heat transfer process like quenching. The experimental observation presented in this paper reveals the limitation of existing models and suggests the new physical insight needed to improve them. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2015

Mechanical properties of water-assembled graphene oxide Langmuir monolayers: Guiding controlled transfer

Liquid-phase transfer of graphene oxide (GO) and reduced graphene oxide (RGO) monolayers is investigated from the perspective of the mechanical properties of these films. Monolayers are assembled in a Langmuir–Blodgett trough, and oscillatory barrier measurements are used to characterize the resulting compressive and shear moduli as a function of surface pressure. GO monolayers are shown to develop a significant shear modulus (10–25 mN/m) at relevant surface pressures while RGO monolayers do not. The existence of a shear modulus indicates that GO is acting as a two-dimensional solid driven by strong interaction between the individual GO sheets. The absence of such behavior in RGO is attributed to the decrease in oxygen moieties on the sheet basal plane, permitting RGO sheets to slide across one another with minimum energy dissipation. Knowledge of this two-dimensional solid behavior is exploited to successfully transfer large-area, continuous GO films to hydrophobic Au substrates. The key to successful transfer is the use of shallow-angle dipping designed to minimize tensile stress present during the insertion or extraction of the substrate. A shallow dip angle on hydrophobic Au does not impart a beneficial effect for RGO monolayers, as these monolayers do not behave as two-dimensional solids and do not remain coherent during the transfer process. As a result, we hypothesize that this observed correlation between monolayer mechanical properties and continuous film transfer success is more universally applicable across substrate hydrophobicities and could be exploited to control the transfer of films composed of two-dimensional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

BioADAPT-MRC: adversarial learning-based domain adaptation improves biomedical machine reading comprehension task

ABSTRACT Motivation Biomedical machine reading comprehension (biomedical-MRC) aims to comprehend complex biomedical narratives and assist healthcare professionals in retrieving information from them. The high performance of modern neural network-based MRC systems depends on high-quality, large-scale, human-annotated training datasets. In the biomedical domain, a crucial challenge in creating such datasets is the requirement for domain knowledge, inducing the scarcity of labeled data and the need for transfer learning from the labeled general-purpose (source) domain to the biomedical (target) domain. However, there is a discrepancy in marginal distributions between the general-purpose and biomedical domains due to the variances in topics. Therefore, direct-transferring of learned representations from a model trained on a general-purpose domain to the biomedical domain can hurt the model’s performance. Results We present an adversarial learning-based domain adaptation framework for the biomedical machine reading comprehension task (BioADAPT-MRC), a neural network-based method to address the discrepancies in the marginal distributions between the general and biomedical domain datasets. BioADAPT-MRC relaxes the need for generating pseudo labels for training a well-performing biomedical-MRC model. We extensively evaluate the performance of BioADAPT-MRC by comparing it with the best existing methods on three widely used benchmark biomedical-MRC datasets—BioASQ-7b, BioASQ-8b and BioASQ-9b. Our results suggest that without using any synthetic or human-annotated data from the biomedical domain, BioADAPT-MRC can achieve state-of-the-art performance on these datasets. Availability and implementation BioADAPT-MRC is freely available as an open-source project at https://github.com/mmahbub/BioADAPT-MRC. Supplementary information Supplementary data are available at Bioinformatics online.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2015

Implementation of spot scanning dose optimization and dose calculation for helium ions in Hyperion

Purpose: Helium ions ({sup 4}He) may supplement current particle beam therapy strategies as they possess advantages in physical dose distribution over protons. To assess potential clinical advantages, a dose calculation module accounting for relative biological effectiveness (RBE) was developed and integrated into the treatment planning system Hyperion. Methods: Current knowledge on RBE of {sup 4}He together with linear energy transfer considerations motivated an empirical depth-dependent “zonal” RBE model. In the plateau region, a RBE of 1.0 was assumed, followed by an increasing RBE up to 2.8 at the Bragg-peak region, which was then kept constant over the fragmentation tail. To account for a variable proton RBE, the same model concept was also applied to protons with a maximum RBE of 1.6. Both RBE models were added to a previously developed pencil beam algorithm for physical dose calculation and included into the treatment planning system Hyperion. The implementation was validated against Monte Carlo simulations within a water phantom using γ-index evaluation. The potential benefits of {sup 4}He based treatment plans were explored in a preliminary treatment planning comparison (against protons) for four treatment sites, i.e., a prostate, a base-of-skull, a pediatric, and a head-and-neck tumor case. Separate treatment plans taking into account physical dose calculation only or using biological modeling were created for protons and {sup 4}He. Results: Comparison of Monte Carlo and Hyperion calculated doses resulted in a γ{sub mean} of 0.3, with 3.4% of the values above 1 and γ{sub 1%} of 1.5 and better. Treatment plan evaluation showed comparable planning target volume coverage for both particles, with slightly increased coverage for {sup 4}He. Organ at risk (OAR) doses were generally reduced using {sup 4}He, some by more than to 30%. Improvements of {sup 4}He over protons were more pronounced for treatment plans taking biological effects into account. All OAR doses were within tolerances specified in the QUANTEC report. Conclusions: The biological {sup 4}He model proposed above is a first approach matching biological data published so far. The advantage of {sup 4}He seems to lie in the reduction of dose to surrounding tissue and to OARs. Nevertheless, additional biological experiments and treatment planning studies with larger patient numbers and more tumor indications are necessary to study the possible benefits of helium ion beam therapy in detail.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2019

Extraction and Parametrization of Isobaric Trinucleon Elastic Cross Sections and Form Factors

By mining data from Jefferson Lab Hall A experiment E08-014 a new 3 He elastic cross section was extracted from a large quasielastic background. This measurement was taken with an initial beam energy of 3.356 GeV and an angle of 20.51°. The cross section was found to be 1.345 × 10 -6 µb/sr ± 0.086 × 10 -6 µb/sr at Q 2 = 34.19 fm -2 . This new data point falls approximately halfway between the first and second diffractive minima of the 3 He form factors. When combined with recent high Q 2 3 He elastic cross section measurements from Jefferson Lab and MIT-Bates this new data point improves our knowledge of the cross section and form factors at large momentum transfers. The new high Q 2 data motivate a reanalysis of the 3 He elastic cross section world data and provide an improved understanding of the magnetic form factor in particular. For this analysis the elastic cross section world data for 3 He, and its mirror nuclei 3 H, were collected. The world data spans a time frame from 1965 to 2016. The dataset contains electron energy ranges from tens of MeV to above 12 GeV for measurements performed at many different facilities. The world data were then fit using a sum of Gaussians parametrization which allowed for the extraction of both targets’ magnetic and electric form factors which were then used to calculate charge densities and radii. The new charge and magnetic form factors for 3 H and the charge form factor for 3 He are in good agreement with the 1994 fits from Amroun et al . However, the addition of the new high Q 2 data has caused the 3 He magnetic form factor’s first diffractive minimum to shift up in Q 2 by 1-3 fm -2 while also decreasing the magnitude of the magnetic form factor above Q2 ≈ 20 fm -2 . The first diffractive minima for 3H are located at Q2 ≈ 13 fm -2 and Q 2 ≈ 23-24 fm -2 for the charge and magnetic form factors respectively. The first diffractive minima for 3 He are located at Q 2 ≈ 11 fm -2 and Q 2 ≈ 17-20 fm -2 for the charge and magnetic form factors respectively. The charge radius for 3 He was found to be 1.90 fm ± 0.00144 fm in reasonable agreement with past measurements, and the charge radius for 3 H was found to be 2.02 fm ± 0.0133 fm which is much larger than past measurements. However, each of these charge radii has an additional uncertainty that must be applied to them due to allowing all parameters to float freely during the sum of Gaussians fitting procedure. This additional uncertainty should be small for 3 He, but it is likely quite significant for 3 H and would help bring this charge radius closer to agreement with past measurements that made different fitting choices. Unfortunately, this analysis was unable to quantify this additional uncertainty. The new form factor fits were compared to modern theoretical predictions from the 2016 paper of Marcucci et al . The ‘conventional’ theoretical approach applied in this paper modelled two and three-body nucleon interactions with relativistic corrections and was reasonably successful at predicting the charge form factors of 3 H and 3 He. χEFT predictions were also often successful. However, while the ‘conventional’ approach still performed best, theory failed to accurately predict the magnetic form factors of either 3 H or 3 He. The first diffractive minimum of the new 3 He magnetic form factor fits actually moved further away from theory. This disagreement between theory and experiment provides motivation for new asymmetry measurements using polarized 3 He and a polarized electron beam. When the beam is scanned in Q 2 on the target the sign of the asymmetry will flip at the form factor minima pinning down their true location.

Barcus, Scott↗
NASA NTRS1975

Effect of various material properties on the adhesive stage of fretting

Various properties of metals and alloys have been studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films have all been found to influence adhesion. High atomic density, low surface energy grain orientations exhibit lower adhesion than other orientations. Hexagonal metals in general manifest less adhesive wear than cubic metal. Knowledge of interfacial surface binding energies can assist in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents can accomplish both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗