SEARCH · Engineering Papers

Results for “Geometry Visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Pre-Transient Characterization of Historic EBR-II Pins for Transient Testing

Current interest in sodium-cooled fast reactor (SFR) designs, such as TerraPower’s Natrium Reactor, has highlighted the need for advanced reactor fuel technology development. Modern U-Zr and U- Pu-Zr pin designs are primary candidates to fuel SFRs and boast high fuel utilization capacity, increased fuel-cladding compatibility, and improved safety through inherent feedback mechanisms. Despite over 60 years of metallic fuel irradiation, uncertainties exist in the performance of the fuel system, particularly under transient overpower (TOP) and loss of flow (LOF) scenarios. Throughout historical testing within the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF), fuel behavior has demonstrated benign response to transient reactor conditions; however, accurate predictions of failure thresholds to inform operational limitations rely heavily on fuel composition, burnup, and irradiation history. In expanding TOP and LOF testing, the Transient Heat sink Overpower Response (THOR) Capsule will be used to test modern fuel technologies in a static sodium environment in the Transient Reactor Test (TREAT) Facility. The THOR capsule is highly instrumented and will provide time-dependent thermal behavior of SFR fuel pins subjected to accident conditions within TREAT. The THOR-Metallic (THOR- M) campaign aims to validate and expand historical TOP and LOF testing on high burnup U-Zr and U-Pu- Zr fuel alloys previously irradiated in EBR-II by running the rods to failure. This contribution focuses primarily on the pre-transient engineering-scale destructive and non- destructive characterization that has been conducted on both the test and sibling pins used for the TOP and LOF tests. All pins underwent visual examination, neutron radiography, element contact profilometry, and precise gamma scan. The sibling pins used for each test were further analyzed using gas assay, sampling, and recharge analysis (GASR), and optical microscopy. The results from each technique confirmed that the fuel pins were intact and devoid of any atypical developments when compared to historical data. Additionally, the analyzed measurements establish a baseline for comparison to post-transient analysis. Key fuel behaviors quanitifed include axial elongation of the fuel column, diametral strain of the pin, patterns in fluff structure geometry, changes in axial isotope distribution, evolution of constituent redistribution, porosity, and fission gas release. The pre-transient measurements and changes attributed to transient behavior from post-transient measurement will be compared to historical data to capture the behavioral dependence on composition, burnup, and irradiation history. Results from this work advance the initiatives of the THOR-M campaign, which aid in informing fuel performance models and establishing safety criteria for SFR operational limits. The novel combination of test environment, in-situ instrumentation, and comprehensive suite of characterization methods provides greater understanding of transient fuel behavior. Overall, information on the time and condition of pin failure for high burnup U-Pu-Zr will greatly expand the limited existing TOP and LOF test data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1985

Investigation of flowfields found in typical combustor geometries

Activities undertaken during the entire course of research are summarized. Studies were concerned with experimental and theoretical research on 2-D axisymmetric geometries under low speed nonreacting, turbulent, swirling flow conditions typical of gas turbine and ramjet combustion chambers. They included recirculation zone characterization, time-mean and turbulence simulation in swirling recirculating flow, sudden and gradual expansion flowfields, and furher complexities and parameter influences. The study included the investigation of: a complete range of swirl strengths; swirler performance; downstream contraction nozzle sizes and locations; expansion ratios; and inlet side-wall angles. Their individual and combined effects on the test section flowfield were observed, measured and characterized. Experimental methods included flow visualization (with smoke and neutrally-buoyant helium-filled soap bubbles), five-hole pitot probe time-mean velocity field measurements, and single-, double-, and triple-wire hot-wire anemometry measurements of time-mean velocities, normal and shear Reynolds sresses. Computational methods included development of the STARPIC code from the primitive-variable TEACH computer code, and its use in flowfield prediction and turbulence model development.

Lilley, D. G.↗

DOE OSTI2022

Historic Submarine Landslides in the Northern Gulf of Mexico

This dataset provides a set of polygons representing the zone of depletion for historic submarine landslides (also referred to as mass transport deposits) within four regions of the US Exclusive Economic Zone in the northern Gulf of Mexico. Landslides were digitized by geologists and spatial scientists at the National Energy Technology Laboratory by visually interpreting landslide boundaries from a seismic-derived, high resolution bathymetric hillshade provided by the Bureau of Ocean and Energy Management (BOEM, 2017). A portion of the landslide features are derived from other spatial sources including the Seismic Water Anomalies dataset by BOEM (2016) as well as from McAdoo et al., 2000 and Twichell et al, 2005. The scale that landslides depletion areas can be interpreted at is limited by the spatial resolution of the gridded bathymetry, which is 12.192 meters (BOEM, 2017). For each landslide feature in the dataset, geometry metrics were calculated including geodesic area (km2) and geodesic perimeter (km) using the North America Albers Equal Area Conic projected coordinate system. The same geometry metrics were calculated for the four inventory regions.

DOE↗

NASA NTRS1951

Theoretical Investigation of Submerged Inlets at Low Speeds

The general characteristics of the flow field in a submerged air inlet are investigated by theoretical, wind-tunnel, and visual-flow studies. Equations are developed for calculating the laminar and turbulent boundary-layer growth along the ramp floor for parallel, divergent, and convergent ramp walls, and a general equation is derived relating the boundary-layer pressure losses to the boundary-layer thickness. It is demonstrated that the growth of the boundary layer on the floor of the divergent-ramp inlet is retarded and that a vortex pair is generated in such an inlet. Functional relationships are established between the pressure losses in the vortices and the geometry of the inlet. A general discussion of the boundary layer and vortex formations is included, in which variations of the various losses and of the incremental external drag with mass-flow ratio are considered. Effects of compressibility are also discussed.

Sacks, Alvin H.↗

NASA NTRS2001

The Transfer Function Model as a Tool to Study and Describe Space Weather Phenomena

The Transfer Function Model (TFM) is a semi-analytical, linear model that is designed especially to describe thermospheric perturbations associated with magnetic storms and substorm. activity. It is a multi-constituent model (N2, O, He H, Ar) that accounts for wind induced diffusion, which significantly affects not only the composition and mass density but also the temperature and wind fields. Because the TFM adopts a semianalytic approach in which the geometry and temporal dependencies of the driving sources are removed through the use of height-integrated Green's functions, it provides physical insight into the essential properties of processes being considered, which are uncluttered by the accidental complexities that arise from particular source geometrie and time dependences. Extending from the ground to 700 km, the TFM eliminates spurious effects due to arbitrarily chosen boundary conditions. A database of transfer functions, computed only once, can be used to synthesize a wide range of spatial and temporal sources dependencies. The response synthesis can be performed quickly in real-time using only limited computing capabilities. These features make the TFM unique among global dynamical models. Given these desirable properties, a version of the TFM has been developed for personal computers (PC) using advanced platform-independent 3D visualization capabilities. We demonstrate the model capabilities with simulations for different auroral sources, including the response of ducted gravity waves modes that propagate around the globe. The thermospheric response is found to depend strongly on the spatial and temporal frequency spectra of the storm. Such varied behavior is difficult to describe in statistical empirical models. To improve the capability of space weather prediction, the TFM thus could be grafted naturally onto existing statistical models using data assimilation.

Porter, Hayden S.↗

NASA NTRS1999

In Situ Identification of Mineral Resources with an X-Ray-Optical "Hands-Lens" Instrument

The recognition of material resources on a planetary surface requires exploration strategies not dissimilar to those employed by early field geologists who searched for ore deposits primarily from surface clues. In order to determine the location of mineral ores or other materials, it will be necessary to characterize host terranes at regional or subregional scales. This requires geographically broad surveys in which statistically significant numbers of samples are rapidly scanned from a roving platform. To enable broad-scale, yet power-conservative planetary-surface exploration, we are developing an instrument that combines x-ray diffractometry (XRD), x-ray fluorescence spectrometry (XRF), and optical capabilities; the instrument can be deployed at the end of a rover's robotic arm, without the need for sample capture or preparation. The instrument provides XRD data for identification of mineral species and lithological types; diffractometry of minerals is conducted by ascertaining the characteristic lattice parameters or "d-spacings" of mineral compounds. D-spacings of 1.4 to 25 angstroms can be determined to include the large molecular structures of hydrated minerals such as clays. The XRF data will identify elements ranging from carbon (Atomic Number = 6) to elements as heavy as barium (Atomic Number = 56). While a sample is being x-rayed, the instrument simultaneously acquires an optical image of the sample surface at magnifications from lx to at least 50x (200x being feasible, depending on the sample surface). We believe that imaging the sample is extremely important as corroborative sample-identification data (the need for this capability having been illustrated by the experience of the Pathfinder rover). Very few geologists would rely on instrument data for sample identification without having seen the sample. Visual inspection provides critical recognition data such as texture, crystallinity, granularity, porosity, vesicularity, color, lustre, opacity, and so forth. These data can immediately distinguish sedimentary from igneous rocks, for example, and can thus eliminate geochemical or mineral ambiguities arising, say between arkose and granite. It would be important to know if the clay being analyzed was part of a uniform varve deposit laid down in a quiescent lake, or the matrix of a megabreccia diamictite deposited as a catastrophic impact ejecta blanket. The unique design of the instrument, which combines Debye-Scherrer geometry with elements of standard goniometry, negates the need for sample preparation of any kind, and thus negates the need for power-hungry and mechanically-complex sampling systems that would have to chip, crush, sieve, and mount the sample for x-ray analysis. Instead, the instrument is simply rested on the sample surface of interest (like a hand lens); the device can interrogate rough rock surfaces, coarse granular material, or fine rock flour. A breadboard version of the instrument has been deployed from the robotic arm of the Marsokhod rover in field trials at NASA Ames, where large vesicular boulders were x-rayed to demonstrate the functionality of the instrument design, and the ability of such a device to comply with constraints imposed by a roving platform. Currently under development is a flight prototype concept of this instrument that will weigh 0.3 kg, using about 4500 J of energy per sample analysis. It requires about 5 min. for XRD analysis, and about 30 min. for XRF interrogation. Its small mass and rugged design make it ideal for deployment on small rovers of the type currently envisaged for the exploration of Mars (e.g., Sojourner-scale platforms). The design utilizes a monolithic P-N junction photodiode pixel array for XRD, a Si PIN photodiode/avalanche photodiode system for XRF, and an endoscopic imaging camera system unobtrusively embedded between the detectors and the x-ray source (the endoscope with its board-mounted camera can be adapted for IR light in addition to visible wavelenths. A rugged, miniature (7 cu cm) x-ray source for the instrument has already been breadboarded.

Marshall, J.↗

NASA NTRS2004

Examples of Current and Future Uses of Neural-Net Image Processing for Aerospace Applications

Feed forward artificial neural networks are very convenient for performing correlated interpolation of pairs of complex noisy data sets as well as detecting small changes in image data. Image-to-image, image-to-variable and image-to-index applications have been tested at Glenn. Early demonstration applications are summarized including image-directed alignment of optics, tomography, flow-visualization control of wind-tunnel operations and structural-model-trained neural networks. A practical application is reviewed that employs neural-net detection of structural damage from interference fringe patterns. Both sensor-based and optics-only calibration procedures are available for this technique. These accomplishments have generated the knowledge necessary to suggest some other applications for NASA and Government programs. A tomography application is discussed to support Glenn's Icing Research tomography effort. The self-regularizing capability of a neural net is shown to predict the expected performance of the tomography geometry and to augment fast data processing. Other potential applications involve the quantum technologies. It may be possible to use a neural net as an image-to-image controller of an optical tweezers being used for diagnostics of isolated nano structures. The image-to-image transformation properties also offer the potential for simulating quantum computing. Computer resources are detailed for implementing the black box calibration features of the neural nets.

Decker, Arthur J.↗

NASA NTRS1990

Workspace visualization and time-delay telerobotic operations

The paper examines the performance of telerobotic tasks where the operator and robot are physically separated, and a comunication time delay of up to several seconds between them exists. This situation is applicable to space robotic servicing-assembly-maintenance operations on low earth or geosynchronous orbits with a ground-based command station. Attention is given to two developments which address advanced time-delay teleoperations for unstructured tasks: (1) the 'phantom robot', a real-time predictive graphics simulator developed to allow teleoperator eye-to-hand coordination or robot free-space kinematics under a time delay of several seconds; and (2) shared compliance control, a modified form of automatic electromechanical impedance control employed in parallel with manual position control to permit soft contact and grasp compliance with workpiece geometry under a time delay of several seconds.

Schenker, P. S.↗

NASA NTRS1995

Low-speed longitudinal aerodynamic characteristics through poststall for 21 novel planform shapes

To identify planform characteristics which have promise for a highly maneuverable vehicle, an investigation was conducted in the Langley Subsonic Basic Research Tunnel to determine the low-speed longitudinal aerodynamics of 21 planform geometries. Concepts studied included twin bodies, double wings, cutout wings, and serrated forebodies. The planform models tested were all 1/4-in.-thick flat plates with beveled edges on the lower surface to ensure uniform flow separation at angle of attack. A 1.0-in.-diameter cylindrical metric body with a hemispherical nose was used to house the six-component strain gauge balance for each configuration. Aerodynamic force and moment data were obtained across an angle-of-attack range of 0 to 70 deg with zero sideslip at a free-stream dynamic pressure of 30 psf. Surface flow visualization studies were also conducted on selected configurations using fluorescent minitufts. Results from the investigation indicate that a cutout wing planform can improve lift characteristics; however, cutout size, shape, and position and wing leading-edge sweep will all influence the effectiveness of the cutout configuration. Tests of serrated forebodies identified this concept as an extremely effective means of improving configuration lift characteristics; increases of up to 25 percent in the value of maximum lift coefficient were obtained.

Gatlin, Gregory M.↗

NASA NTRSDate not supplied

Investigation of Physical Mechanisms for Jet Noise Reduction by Plug Nozzle Porosity

This paper presents the results of a computational study on porous-plug nozzles for their eventual application in reducing takeoff noise levels for supersonic civil transport. The study explores a wide range of porous-plug geometries, encompassing variations in hole size, plug length and porosity. Computational fluid dynamics (CFD) analyses are employed in concert with an advanced automated mesh refinement (AMR) scheme, Sketch-to-Solution (S2S), to investigate porous plug nozzle design strategies that may diminish shock strength, broad-band shock noise (BBSN), flow separation, and other undesirable characteristics associated with high takeoff noise levels. A selected subset of the porous-plug nozzles that were analyzed computationally were manufactured at subscale using stereolithography 3D printing. These nozzles were tested experimentally, obtaining far-field noise spectral data and schlieren flow visualization pictures. Detailed comparisons between CFD predictions and experimental results were conducted. These comparisons focus on gaining a better understanding of the underlying physical mechanisms responsible for noise reduction with the porous plugs relative to corresponding solid plugs.

computational fluid dynamics↗

NASA NTRSDate not supplied

Investigation of Physical Mechanisms for Jet Noise Reduction by Plug Nozzle Porosity

Nozzles↗

DOE OSTI2025

Microscopic signatures of topology in twisted MoTe 2

In moiré materials with flat electronic bands and suitable quantum geometry, strong correlations can give rise to various topological states of matter. The non-trivial band topology of twisted MoTe 2 , which is responsible for its fractional quantum anomalous Hall states, is predicted to arise from a skyrmion lattice texture in the layer pseudospin of the electronic wavefunctions. Tracing the layer polarization of wavefunctions within the moiré unit cell can, thus, offer insights into the band topology. Here we measure the out-of-plane component of the layer-pseudospin skyrmion textures of twisted MoTe 2 using scanning tunnelling microscopy and spectroscopy. We do this by simultaneously visualizing the moiré lattice structure and the spatial localization of its electronic states. We find that the wavefunctions associated with the topological flat bands exhibit a spatially dependent layer polarization within the moiré unit cell, in agreement with our theoretical modelling. Furthermore, our work enables future local probe studies of the intertwined correlated and topological states arising in gate-tunable devices.

Electronic properties and materials↗

NASA NTRS2012

Tidal Control of Jet Eruptions Observed by Cassini ISS

Observations by Cassini's Imaging Science Subsystem (ISS) of Enceladus' south polar region at high phase angles has revealed jets of material venting into space. Observations by Cassini's Composite Infrared Spectrometer (CIRS) have also shown that the south polar region is anomalously warm with hotspots associated with geological features called the Tiger Stripes. The Tiger Stripes are large rifts near the south pole of Enceladus, which are typically about 130 km in length, 2 km wide, with a trough 500 m deep, and are l1anked on each side by 100m tall ridges. Preliminary triangulation of jets as viewed at different times and with different viewing geometries in Cassini ISS images taken between 2005 and 2007 have constrained the locations of eight major eruptions of material and found all of them associated with the south polar fractures unofficially the 'Tiger Stripes', and found four of them coincident with the hotspots reported in 2006 by CIRS. While published ISS observations of jet activity suggest that individual eruption sites stay active on the timescale of years, any shorter temporal variability (on timescales of an orbital period, or 1.3 Earth days, for example) is more difficult to establish because of the spotty temporal coverage and the difficulty of visually isolating one jet from the forest of many seen in a typical image. Consequently, it is not known whether individual jets are continuously active, randomly active, or if they erupt on a predictable, periodic schedule. One mechanism that may control the timing of eruptions is diurnal tidal stress, which oscillates between compression/tension as well as right and left lateral shear at any given location throughout Enceladus' orbit and may allow the cracks to open and close regularly. We examine the stresses on the Tiger Stripe regions to see how well diurnal tidal stress caused by Enceladus' orbital eccentricity may possibly correlate with and thus control the observed eruptions. We then identify possible mechanisms by which tidal stress can provide access to the surface for volatile material and implications for observed jet activity.

Hurford, T. A.↗

NASA NTRS1990

Testing of 3-D models in 2-D adaptive wall test sections

Considerable effort was devoted to the development of two-dimensional adaptive wall test sections. The development of fully three-dimensional test sections, however, has not had this same level of effort expended. The limitations on three-dimensional research are the result of the complexity of both the mechanical design and operational aspects. Typical of the mechanical complexities are lack of readily available model and flow visualization access, and problems of sealing between adjacent walls for multi-wall types of test sections. The operational aspects are complicated by the necessity for many measurements of the boundary conditions which can be very time consuming. In three-dimensional testing, it is impossible to remove all of the boundary interference. It will be necessary, therefore, to apply residual corrections to the data. The more complex the test section shape, the more complex the calculation of the residual corrections becomes. From both the viewpoint of test section complexity and of ease of residual corrections, a simplified test section geometry is desirable. To aid in the design of simplified test sections, several researchers investigated the capability of using two-dimensional adaptive wall test sections to perform three-dimensional testing. By use of this type of design, the inherent complications and limitations of the fully three-dimensional design are avoided. Strategies of adaptation used for this application are described, as well as, sample results and a discussion of some limitations of the technique.

Wedemeyer, Erich H.↗

NASA NTRS2004

The Lewice Console

Lewice (LEWis ICE accretion program) is software used by literally hundreds of users in the aeronautics community for predicting ice shapes, collections efficiencies, and anti-icing heat requirements for aircraft. LEWICE performs its analysis in minutes on a desktop PC, allowing the user to run several parameter studies for design purposes. The ice shape predictions have been used to assess performance degradation both as an input to a CFD program or experimentally in flight or in a wind tunnel. This information is important to ensure an airplane s safe passage through an icing cloud. Currently, Lewice runs as a DOS program that accepts many different inputs such as cloud conditions, wing shapes, and thermal deicing inputs. Usually, such experimental data is stored in spreadsheets. However, Lewice inputs are text files; therefore, they must be generated by the user. Lewice s outputs (collection efficiency, ice shapes and thicknesses) are also text files; to plot the data, users must generate a spreadsheet with this output. Because all Lewice J/O is in the form of text files, using Lewice can be tricky and time-consuming. Our goal was to improve Lewice s usability by creating a user interface that would automatically generate Lewice input from a spreadsheet and automatically put Lewice output into spreadsheets with charts. Additionally, this user interface would automatically convert units (as Lewice only accepts input in certain units) and offer several output options. I call this program the Lewice Console. The Lewice Console is an easy to use interface for Lewice written in Visual Basic. It allows users to run Lewice given a spreadsheet listing experimental conditions. It automatically generates the input to Lewice, does necessary unit conversions, runs Lewice, and produces a spreadsheet with charts plotting the data. It allows users to import data from previously generated Lewice inputs into a spreadsheet. It also allows users to batch run Lewice on several different inputs to automatically generate multiple output spreadsheets. You can also generate plots of actual data vs. experimental data. These capabilities are just the beginning for the Lewice Console. Lewice is capable of running a full deicing experiment given a geometry and heating apparatus information. However, users find it difficult to run such experiments due to the number of inputs and the difficult input file format. The Lewice Console would simplify experiment generation by allowing the user to interactively draw a geometry, place heating apparatus, and specify information about each part. The input to Lewice would be automatically generated from the experiment the user draws on the screen. The Lewice Console would simplify the experiment building process. Currently, Lewice runs as a DOS program that accepts many different inputs such as

Armstrong, Aaron E.↗

NASA NTRS2010

PLOT3D Export Tool for Tecplot

The PLOT3D export tool for Tecplot solves the problem of modified data being impossible to output for use by another computational science solver. The PLOT3D Exporter add-on enables the use of the most commonly available visualization tools to engineers for output of a standard format. The exportation of PLOT3D data from Tecplot has far reaching effects because it allows for grid and solution manipulation within a graphical user interface (GUI) that is easily customized with macro language-based and user-developed GUIs. The add-on also enables the use of Tecplot as an interpolation tool for solution conversion between different grids of different types. This one add-on enhances the functionality of Tecplot so significantly, it offers the ability to incorporate Tecplot into a general suite of tools for computational science applications as a 3D graphics engine for visualization of all data. Within the PLOT3D Export Add-on are several functions that enhance the operations and effectiveness of the add-on. Unlike Tecplot output functions, the PLOT3D Export Add-on enables the use of the zone selection dialog in Tecplot to choose which zones are to be written by offering three distinct options - output of active, inactive, or all zones (grid blocks). As the user modifies the zones to output with the zone selection dialog, the zones to be written are similarly updated. This enables the use of Tecplot to create multiple configurations of a geometry being analyzed. For example, if an aircraft is loaded with multiple deflections of flaps, by activating and deactivating different zones for a specific flap setting, new specific configurations of that aircraft can be easily generated by only writing out specific zones. Thus, if ten flap settings are loaded into Tecplot, the PLOT3D Export software can output ten different configurations, one for each flap setting.

Alter, Stephen↗

DOE OSTI2022

Effect of coaxial nozzle wear on catchment efficiency in direct energy deposition built components

Laser based Direct Energy Deposition (DED) systems using metallic powder feedstock are recognized as a promising manufacturing method for their ability to shorten production cycles and create complex part geometries. Components are built by generating a melt pool with a high-power laser beam while material is coaxially injected and left to solidify. An impediment to large scale use of DED lies in poor powder catchment efficiency, the condition in which a portion of injected powder escapes the melt pool resulting in a ratio of decreased printed material mass to mass of supplied feedstock. The wear state of a coaxial nozzle on a DED system within a hybrid manufacturing machine tool has been observed to decrease catchment efficiency over time. Herein this study investigates this effect by adapting flow visualization techniques to an in-situ process monitoring format, the implementation of a Computational Fluid Dynamics (CFD) simulation, and deposition testing. Nozzle geometric defects due to wear are identified and categorized, and the impact of nozzle tip wear, resulting in axial tip reduction, on powder catchment efficiency is proven by multiple calculation methods. A linear correlation between catchment efficiency and powder stream diameter is identified, causing a 15–20% loss in efficiency sustained over incremental nozzle tip reduction up to − 1 mm. These results provide a foundation for further study of wear effects and Zero defect manufacturing solutions for powder fed DED systems.

42 ENGINEERING↗

NASA NTRS2005

Managed Development Environment Successes for MSFC's VIPA Team

This paper outlines the best practices of the Vehicle Design Team for VIPA. VIPA is the Vehicle Integrated Performance Analysis Team at MSFC. This team was created to reconnect the individual engineering disciplines to be able to perform system level technical assessments in support of program decisions. The functions of the VIPA Vehicle Design (VVD) discipline team are to maintain the controlled reference geometry and provide linked, simplified geometry for each of the other discipline analyses. The core of the VVD work, and the approach for VVD s first task of controlling the reference geometry, involves systems engineering, top-down, layout-based CAD modeling within a Product Data Manager (PDM) development environment. The topdown approach allcws for simple contrnl of very large, integrated assemblies and greatly enhances the ability to generate trade configurations and reuse data. The second W D task, model simplification for analysis, is handled within the managed environment through application of the master model concept. In this approach, there is a single controlling, or master, product definition dataset. Connected to this master model are reference datasets with live geometric and expression links. The referenced models can be for drawings, manufacturing, visualization, embedded analysis, or analysis simplification. A discussion of web based interaction, including visualization, between the design and other disciplines is included. Demonstrated examples are cited, including the Space Launch Initiative development cycle, the Saturn V systems integration and verification cycle, an Orbital Space Plane study, and NASA Exploration Office studies of Shuttle derived and clean sheet launch vehicles. The VIPA Team has brought an immense amount of detailed data to bear on program issues. A central piece of that success has been the Managed Development Environment and the VVD Team approach to modeling.

Finckenor, Jeff↗