SEARCH · Engineering Papers

Results for “GAS MIXTURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

NASA NTRS1978

Organic molecules in the atmosphere of Jupiter

Organic synthesis in the primitive solar system was simulated by Fischer Tropsch type experiments. Particular attention was given to the formation of lower molecular weight hydrocarbons. In a gas flow experiment, a gas mixture of H2 and CO was introduced into a heated reaction tube at a constant flow rate and passed through a catalyst (powdered Canyon Diablo). The products that emerged were directly analyzed by gas chromatography. The results of 21 runs under various gas mixing rations, reaction temperatures, and gas-catalyst contact times showed the predominance of the saturated hydrocarbon formation at C sub 4 and C sub 5 over the unsaturated ones. Saturate/unsaturate ratios were mostly less than 0.4 and none showed over 0.7.

Ponnamperuma, C. A.↗

NASA NTRS1979

Preparation of dielectric coating of variable dielectric constant by plasma polymerization

A plasma polymerization process for the deposition of a dielectric polymer coating on a substrate comprising disposing of the substrate in a closed reactor between two temperature controlled electrodes connected to a power supply is presented. A vacuum is maintained within the closed reactor, causing a monomer gas or gas mixture of a monomer and diluent to flow into the reactor, generating a plasma between the electrodes. The vacuum varies and controls the dielectric constant of the polymer coating being deposited by regulating the gas total and partial pressure, the electric field strength and frequency, and the current density.

Hudis, M.↗

NASA NTRS1979

Investigation of air stream from combustor-liner air entry holes, 3

Jets flowing from air entry holes of the combustor liner of a gas turbine were investigated. Cold air was supplied through the air entry holes into the primary hot gas flows. The mass flow of the primary hot gas and issuing jets was measured, and the behavior of the air jets was studied by the measurement of the temperature distribution of the gas mixture. The air jets flowing from three circular air entry holes, single streamwise long holes, and two opposing circular holes, parallel to the primary flow were studied along with the effects of jet and gas stream velocities, and of gas temperature. The discharge coefficient, the maximum penetration of the jets, the jet flow path, the mixing of the jets, and temperature distribution across the jets were investigated. Empirical expressions which describe the characteristics of the jets under the conditions of the experiments were formulated.

Aiba, T.↗

NASA NTRS1985

Monte Carlo simulations in support of the Shuttle upper atmospheric mass spectrometer experiment

This paper presents the results of calculations obtained with a Direct Simulation Monte Carlo (DSMC) method that describes both the external flow about the nose region of the Shuttle Orbiter and the internal flow in an inlet tube that provides the initial path between the shock-processed gases and a mass spectrometer mounted inside the Orbiter. A dedicated, three-dimensional version of the DSMC was developed during this study for the internal flow simulation along with the procedure for interfacing the external and internal flows. The calculations span the 140 to 95 km altitude range, which includes most of the hypersonic transitional flow encountered during reentry. All calculations were for a multicomponent gas mixture consisting of five chemical species while simulating the effects of transitional, rotational, vibrational, and chemical nonequilibrium. The results of the calculations show that within the entry region of the inlet tube where the gas has equilibrated with the sidewall tube temperature, the pressure is substantially less than the pressure at the external surface. This pressure correction for the entry region is significant for all conditions investigated and increases with altitude. The results highlight the structure of both the external and internal flow. Results of parametric studies show the sensitivity of the equilibrated inlet sidewall pressure to mass flow rates, gas-surface reflection model, tube side-wall temperature variations, and surface recombinations.

Moss, J. N.↗

DOE OSTI2022

Findings on Subtask 3.1 - Bakken Rich Gas Enhanced Oil Recovery Project

Total in-place oil for the Bakken petroleum system (BPS) (which includes the Bakken and Three Forks Formations) has been estimated to be 600 billion barrels (bbl). However, BPS wells have decline rates as high as 85% over the first 3 years of their lives, and primary recovery factors typically range from 3% to 10% of original oil in place. Given the low initial recovery rates, even small incremental productivity improvements could dramatically increase technically recoverable oil in the BPS. One potential solution is enhanced oil recovery (EOR) using gas injection, such as carbon dioxide (CO2) or hydrocarbon (HC) gases. While commonly used in conventional reservoirs, CO2 EOR in unconventional tight oil reservoirs has been limited to pilot tests. EOR using rich gas (mixture of methane, ethane, and propane) has also been employed in numerous pilots in several unconventional plays and has recently been successfully applied in the Eagle Ford play. If successful, large-scale gas-based EOR in the BPS could dramatically increase oil productivity and recovery factors and extend the life of the play for decades. While CO2 may be a technically suitable working fluid for EOR in the BPS, supplies are limited and costs for using CO2 in EOR pilots are prohibitively high. Meanwhile, produced gas flaring has presented challenges for BPS operators in North Dakota. Analysis conducted by the North Dakota Pipeline Authority indicates that the current gas-gathering infrastructure in North Dakota is insufficient to accommodate all of the associated gas that is produced from the BPS. The geographically isolated location of North Dakota relative to large natural gas markets, combined with suppressed natural gas prices, has made it economically challenging for industry to invest capital in expanding gas-gathering infrastructure in the state. These circumstances led to a research program conducted by the Energy & Environmental Research Center (EERC) in partnership with Liberty Resources Management Company LLC (LR) to examine the potential to use rich gas injection for EOR and mitigate flaring. A rich gas EOR pilot test was designed and executed by LR at its Stomping Horse development area in Williams County, North Dakota. From July 2018 through May 2019, a total of 160 million standard cubic feet (MMscf) of rich produced gas was injected into the BPS using five different wells in a sequential injection strategy. LR’s Leon–Gohrick drill spacing unit (DSU) was used as the test site. Regulatory oversight was provided by the North Dakota Industrial Commission (NDIC). Technical support was provided by the EERC through a series of laboratory, modeling, and field-based activities, and additional post-pilot research activities incorporated learnings from the test, developed new laboratory data, improved fracture modeling methods, and developed machine learning and big data analytics. The results from the Stomping Horse rich gas EOR pilot activities indicate that developing an effective, economical EOR approach for the BPS will require more field tests. Another key lesson learned from the Stomping Horse tests is that detailed pre- and posttest data on reservoir conditions and fluids production are essential. Robust reservoir characterization provides information that is crucial to creating realistic geomodels and conducting valid dynamic simulations of potential EOR scenarios. A detailed understanding of the completions and production history of offset wells is also necessary for valid test result interpretations. This knowledge is essential to designing the operational parameters of injectivity tests and interpreting the results. A conformance control strategy is also essential to success. Laboratory-based examinations of rich gas interactions with reservoir fluids and rocks were conducted, with an emphasis on determining the ability to mobilize oil in the tight reservoir rocks and shales of the BPS. Injection fluid composition was shown to have a positive impact on reducing reservoir oil minimum miscibility pressure (MMP), reducing interfacial tension (IFT), and altering wettability. IFT and contact angle measurements demonstrated that wettability can be altered in the presence of rich gas, suggesting the potential to improve oil recovery. Iterative modeling of surface infrastructure and reservoir performance using data generated by the various project activities was conducted. A geologic model of the Stomping Horse area was built; history-matched oil, gas, and water production was used in simulations of various EOR scenarios. Early programmatic modeling results were used to support LR’s design and operation of the EOR pilot and to provide insight regarding optimization of future commercial-scale BPS EOR design and operations. Post-pilot modeling focused on alternative methods of understanding complex fracture networks and accelerating simulation time. These led to improved simulation run times and provide excellent history-matching results. Several of these iterative models were used as the bases for developing algorithms into machine learning and big data analytics. History matching in reservoir simulation is time-consuming and computer processing-intensive. Machine learning algorithms were created, and an automated history-matching tool was developed. A large set of synthetic reservoir simulations were created to generate well responses (oil, gas, and water production, well bottomhole pressure [BHP], and tracer or propane breakthrough) for a set of EOR operating parameters that included offset well status (open or closed), injectate (rich gas or propane), injection rate, and injection well BHP. A user interface was developed to provide real-time visualization. Machine learning-based models were developed to provide rapid forecasting of well performance given a set of user-defined EOR operating parameters. These predictive models allow the user to modify the offset well status, injection rate, and injection well BHP and rapidly forecast future production performance. The combination of real-time visualization tools with real-time forecasting tools provides a framework for real-time control—operational changes that the EOR site operator can enact (e.g., changing gas injection rates) to affect the observed performance and potentially improve the EOR outcome. There is great reason to be optimistic about the future of EOR in the Bakken. The results of the laboratory studies suggest significant potential for high rates of oil mobilization using produced field gas injection under the right conditions. The results of the lab studies, combined with rigorous statistical analysis of well production data and associated modeling efforts, confirm the notion that fluid mobility within the reservoir is controlled by fractures. As more knowledge is gained about the nature and distribution of fracture networks in the Bakken, the industry will be in a better position to predict and, ultimately, influence fluid mobility. New field tests are necessary to develop a more complete understanding of those conditions. Thoughtful and creatively engineered field tests within a well-characterized geologic setting will yield the fundamental knowledge needed to take Bakken oil production to the next level. This subtask was cofunded through the EERC–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission’s Oil and Gas Research Program and Computer Modelling Group.

04 OIL SHALES AND TAR SANDS↗

NASA NTRS1978

Gas Control System for HEAO-B

The HEAO-B Gas Control System consists of a high pressure gas storage supply together with distribution and regulation assemblies and their associated electronics for management of gas required for HEAO-B X-ray counter experiments. The Gas Control System replenishes a gas mixture (82 percent argon, 12.3 percent carbon dioxide, 5.7 percent xenon) in the counter volumes which is lost by: diffusion through controlled leakage plugs, diffusion through counter windows, and consumption resulting from periodic purges. The gas density in each counter volume is maintained constant to within 0.25 percent by comparison with a sealed reference volume. The system is fully redundant, capable of operating at atmospheric pressure as well as in a vacuum, contains interlocks which shut down gas flow in the event of either leakage or excessive pressure, and is able to shut down counter high voltage if counter pressure is abnormally low. The system is electronically controlled by ground command and self-sustaining in orbit for a period of at least one year.

Taylor, B.↗

NASA NTRS2003

Solid state potentiometric gaseous oxide sensor

A solid state electrochemical cell (10a) for measuring the concentration of a component of a gas mixture (12) includes first semiconductor electrode (14) and second semiconductor electrode (16) formed from first and second semiconductor materials, respectively. The materials are selected so as to undergo a change in resistivity upon contacting a gas component, such as CO or NO. An electrolyte (18) is provided in contact with the first and second semiconductor electrodes. A reference cell can be included in contact with the electrolyte. Preferably, a voltage response of the first semiconductor electrode is opposite in slope direction to that of the second semiconductor electrode to produce a voltage response equal to the sum of the absolute values of the control system uses measured pollutant concentrations to direct adjustment of engine combustion conditions.

Wachsman, Eric D.↗

NASA NTRSDate not supplied

Characterization of CO 4th Positive Radiation in CO2-Ar Mixtures

This paper presents measurements and simulations of CO 4th Positive spectra obtained in NASA Ames Research Center's Electric Arc Shock Tube (EAST) and CentraleSupelec's Plasma Torch. The experiments were aimed at measuring optically thin emission for the main band features of CO 4th Positive by using test gas mixtures of CO2 and Ar. By using mixtures of CO2 and Ar, the temperature of the flow (and consequently black-body curve) is increased compared to using pure CO2 (or CO2 / N2 mixtures). This temperature increase allows for emission spectroscopy of features that would nominally be black-body limited for conditions relevant to Mars entry. The CO 4th Positive system is the focus of this study as it accounts for a large percentage of the emitted radiation for Martian entry, and also due to the difficulties of obtaining experimental validation data due to the emission appearing in the Vacuum Ultraviolet (VUV) spectral range. The focus of this paper is to provide a comprehensive comparison between the EAST and plasma torch data along with various CO 4th Positive databases available in the literature. Previously reported VUV CO2 / N2 EAST data required a larger temperature than would be predicted based upon equilibrium shock relations. The need for the temperature increase implies that the EAST experiment did not fully equilibrate. Thus, it is presumed that the EAST data did not obtain an equilibrium condition. The plasma torch data, on the other hand, is very consistent with equilibrium assumptions. Thus, the equilibrium data obtained in the plasma torch is utilized to construct the CO 4th Positive emission model, which is then applied to the EAST data with a non-equilibrium interpretation.

A. M. Brandis↗

DOE OSTI2025

Deuterium Extraction from Helium with a Vanadium Vacuum Permeator: Commissioning of the Tritium Extraction eXperiment (TEX)

Here, the Tritium Extraction eXperiment (TEX) is a forced-convection lead-lithium (PbLi) loop in the Safety and Tritium Applied Research (STAR) facility at Idaho National Laboratory (INL) with the purpose of providing validation data for the vacuum permeator tritium extraction concept. A vanadium tube of 1000 mm length, 12.7 mm outside diameter, and 0.50 mm wall thickness is installed in the test section of TEX. The installed vanadium tube is characterized to quantify impurity concentrations, surface chemistry, and microstructure to elucidate permeation phenomena observed in experimentation. Herein, the permeation properties of the vanadium tube are characterized by measuring deuterium permeation at 300 °C, 325 °C, and 350 °C at 100 kPa, 125 kPa, and 150 kPa total pressures with 5000 ppm deuterium in helium gas mixture in a once-through flow configuration. The hydrogen isotope permeation through the vanadium tube in the test section is measured with quadrupole mass spectrometers and the hydrogen isotope concentration in the feed and retentate gas stream is measured with gas chromatography. The transient permeation results are modeled with MELCOR-TMAP, a thermal-hydraulic tritium transport code, and compared well with literature data.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Tank Side Cesium Removal IXC-150 Cask Detonation Report

A set of experiments were conducted at Los Alamos National Laboratory’s firing point 88 to determine the blast pressure and effects of a stoichiometric gas mixture of Hydrogen (H 2 ) and Nitrous Oxide (N 2 O) on the IXC-150 Storage Pad Vent Stack assemblies. The Lab was asked to design, build, and test the vent stack assemblies using a reaction gas volume of 340 in 3 that mimics the Tank Side Cesium Removal (TSCR) Ion Exchange Column (IXC) assembly. The experimental system with vent stack assembly was designed with input from the Washington River Protection Services (WRPS) to ensure an accurate test setup. The tests were conducted at LANL on the newly built filter/gas assembly at the end of April 2021 timeframe, using WRPS supplied vent stack assemblies and internal HEPA filters. The objective of these tests was to observe that the structural integrity of the vent stack assemblies was maintained and determine the resulting blast overpressures at a distance of 16 and 32 inches from the assembly. All work was performed under the LANL Quality Assurance Program (SD330), using a graded application of ASME NQA-1- 2008/NQA-1a-2009. To ensure that all client quality assurance (QA) expectations were addressed, evaluation of the end data needs was performed and the appropriate controls applied for this work.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1979

Noble gas trapping and fractionation during synthesis of carbonaceous matter

An investigation of noble gas entrapment during synthesis of carbonaceous, macromolecular, and kerogen-like substances is presented. High molecular weight organic matter synthesized in aqueous condensation reactions contained little gas, and the composition was consistent with fractionation due to noble gas solubility in water; however, propane soot produced during a modified Miller-Urey experiment in an aritificial gas mixture contained high concentrations of trapped noble gases that displayed strong elemental fractionation from their reservoirs. It is concluded that theses experiemnts show that processes exist for synthesis of carbonaceous carriers that result in high noble gas concentrations and strong elemental fractionation at temperatures well above those required by absorption to achieve similar effects.

Frick, U.↗

DOE OSTI2025

Scaled-up fabrication of durable and porous adsorbent-coated minichannels on aluminum for CO 2 separation

A method was developed to fabricate zeolite 13X adsorbent-coated minichannels on aluminum for CO₂ adsorption applications in this study. It emphasizes the innovative use of aluminum as a substrate, which offers airtight assembly, paving the way for highly efficient adsorption systems. An optimized coating process was developed using a slurry of Zeolite 13X, yeast, sugar, and xanthan gum, resulting in durable and highly porous layers that enhance CO₂ capture performance. A PETG peeler was designed to remove the top layer of the yeast-engineered adsorbent coatings, revealing a super porous and foamy structure. The teeth of the peeler were designed and fabricated for high repeatability and rapid prototyping. Breakthrough experiments were conducted on the scaled-up adsorbent bed using gas mixtures of 80% CO₂, 20% N₂, and 20% CO₂, 80% N₂ to represent different industrial scenarios. The performance of the bed was evaluated at flow rates of 160 and 190 cm³ min -1 using a Raman Laser Gas Analyzer (RLGA), demonstrating stable adsorption without degradation across multiple cycles. Computational modeling of integral transport phenomena under the chosen experimental conditions was pursued using gPROMS ProcessBuilder™, and the modeling results were compared with those from the tests for adsorption time, which resulted in an error margin of 2% to 9% for the breakthrough time, confirming the easy reproducibility of the design through modeling. This research advances CO₂ capture technologies by providing an effective and scalable solution for producing aluminum-based adsorbent coated beds, supporting industrial carbon capture efforts.

CO2 capture↗

DOE OSTI2021

Center for Gas Separations (CGS)

The total energy consumption in the U.S. has been rising steadily for decades, and it currently amounts to ~98,000 TBtu/yr, with approximately 30% of this total attributable to the industrial sector. Reasonable estimates indicate that 45–55% of total industry energy consumption derives from chemical separations, and for example, over 120 TBtu/yr alone is used in carrying out olefin/paraffin separations via energy-intensive cryogenic distillation. Therefore, the pursuit of new, even radically different approaches to some of the most energy-intensive industrial separations processes is an imperative scientific pursuit for reducing energy consumption toward a more sustainable future. Adsorbent and membrane-based separations can require a fraction of the energy needed for distillation methods, and as such are considered promising solutions for balancing increasing energy demand in the U.S. with the need for a massive reduction in energy consumption. Although considerable research effort has been devoted to the design of materials capable of carrying out various gas separations, usually operating through size-selective, chemisorptive, or physisorptive mechanisms, it remains a great challenge to design materials that function adequately for real-world applications. Indeed, the chemical and physical differences between molecules in gas mixtures of interest are often small, and therefore it is necessary, through the use of nanoscience and synthetic chemistry, to engineer unprecedented molecular-level control in adsorbate–adsorbent interactions. The overarching mission of the Center for Gas Separations (CGS) was to discover fundamental innovations that have the potential to dramatically reduce the energy associated with critical gas separations. In particular, the CGS developed novel synthetic routes, guided by molecular chemistry principles, as well as advanced characterization and computational methods, that have enabled the discovery of new materials and membranes tailor-made to exhibit exceptional performance for a range of gas separations processes, as required in the clean use of fossil fuels and in reducing CO 2 emissions from industry. A challenge of this magnitude required the collaboration and synergy of a large team of researchers with expertise in materials synthesis, characterization, and computations. During the 11-year project period, the CGS created a range of new materials within the family of highly-tunable, porous solids known as metal–organic frameworks (MOFs). These new frameworks demonstrate novel mechanisms for key industrial gas separations, including revolutionary new cooperative adsorption processes that enable low-energy CO 2 and CO capture, and are capable of efficiently separating olefins from paraffins, O 2 from air, and the shape-selective separation of alkane isomers. In addition, the CGS developed new strategies for incorporating these materials into composite membranes toward highly efficient and selective membrane-based separations. As a testament to the success of the CGS, two start-up companies, Mosaic Materials,4 Inc. and Flux Technology, Inc., grew out of these research efforts, and these companies are seeking to commercialize MOF and composite membranes materials for key separations in industry, including large-scale CO 2 capture and hydrocarbon separations, respectively. Another company, framergy, Inc., licensed IP resulting from CGS research toward the commercialization of adsorbents for various energy-relevant applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRSDate not supplied

Computational Fluid Dynamics Simulation of A Hazardous Gas Purge System in an EUS Aft Adapter Umbilical Plate Concept

The Fluid Dynamics Branch at the NASA Marshall Space Flight Center actively supports flight programs through a variety of in-line analyses. One area of expertise is the mitigation of hazardous gas mixtures that may form during nominal vehicle fueling operation. After the successful Artemis I launch, design cycles for future iterations of the vehicle are in progress. The subject of this work concerns the analysis of a hazardous gas mitigation system concept for a future upper stage.

Riley D Bridges↗

NASA NTRSDate not supplied

Computational Fluid Dynamics Simulation of A Hazardous Gas Purge System in an EUS Aft Adapter Umbilical Plate Concept

Riley Bridges↗

DOE OSTI2023

Challenges and successes in establishing a multipurpose fuels and materials irradiation capsule [Slides]

This presentation discusses the challenges and success related to designing and fabricating multipurpose capsules for irradiation experiments for irradiation within the Advanced Test Reactor (ATR) to be presented at tje DEVICE-MTR irradiation experiment design working group meeting hosted by the Japanese Atomic Energy Agency (JAEA). The information herein is limited to the design of the capsules only and no programmatic information from any project supporting the design of the multipurpose capsule is discussed. The intent of the design team was establish a capsule design that could accommodate multiple different irradiation project needs for the irradiation of nuclear fuel and materials of interest in the nuclear field. The main points of the presentation are as follows: use of tin as a molten thermal bond material was selected for the fueled capsule design and was found to be inadequate as it would corrode the stainless steel at high temperatures, this capsule design has high sensitivity to manufacturing of the gas gap and control of the gas mixture, and the fueled capsule has experienced welding challenges with the inner capsule material 800H Incoloy.

42 ENGINEERING↗

NASA NTRS1975

Shock tube measurements of specific reaction rates in the branched chain CH4-CO-O2 system

Growth constants, obtained by measuring the blue CO flame band emission behind incident shock waves, were obtained for two elementary bimolecular reactions involved in the oxidation of methane. Gas mixtures containing small amounts of CH4 with varying amounts of CO, O2, and in one case CO2, diluted with argon, were investigated, and exponential growth constants were derived from plots of the logarithm of observed light intensity versus gas time. The rate constant for the reaction O + CH4 yields CH3 + OH was found to be 1.9 times 10 to the 14th exp(-5900/T) cu cm per mole per sec in the range 1300-2000 K; for the reaction CH3 + O2 yields CH3O + O, the rate constant was determined to be 2.4 times 10 to the 13th exp(-14,500/T) cu cm per mole per sec in the range 1200 to 1900 K.

Brabbs, T. A.↗

NASA NTRS1977

Nuclear pumped laser II

The first direct nuclear pumped laser using the He-2-(n,p) H-3 reaction is reported. Lasing took place on the 1.79 microns Ar I transition in a mixture of He-3-Ar at approximately 600 Torr total pressure. It was found that the electrically pulsed afterglow He-Ar laser had the same concentration profile as the nuclear pumped laser. As a result, nuclear lasing was also achieved in He-3-Xe (2.027 micron) and He-3-Kr (2.52 micron). Scaling of laser output with both thermal flux and total pressure as well as minority concentration has been completed. A peak output (He-3-Ar) of 3.7 watts has been achieved at a total pressure of 4 atm. Direct nuclear pumping of He-3-Ne has also been achieved. Nuclear pumping of a He-3-NF3 mixture was attempted, lasing in FI at approximately 7000 A, without success, although the potential lasing transitions appeared in spontaneous emission. Both NF3 and 238UF6 appear to quench spontaneous emission when they constitute more than 1% of the gas mixture.

Deyoung, R. J.↗