Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Reducing DLOFC fuel temperatures by mixing thorium with LEU in a single-zone six-pass fuel cycle in a PBMR-DPP-400 core - 18548

Many studies have been done in neutronics and thermal-hydraulic simulation of the standard 6- pass fuel recirculation scheme for the standard 9.6 wt % enriched, 9 g per fuel sphere low-enriched uranium (LEU) fuel in the PBMR-DPP-400, using different versions of the VSOP diffusion codes. Maximum DLOFC temperatures were all below the upper limit of 1600 deg. C. The DLOFC temperature is highly dependent on the peaking factor of the power; meaning a lower maximum DLOFC temperature can be obtained by suppressing the axial power peak and by moving the radial power peak towards the external reflector. In this study the standard 6-pass fuel recirculation was retained. The improvement strategy was thus attempted by means of flattening the axial power profile by mixing substantial amounts of thorium into the LEU fuel. The addition of thorium led to breading of substantial amounts of {sup 233}U. This led to slower depletion of enrichment with burn-up, which increased fuel reactivity and power densities near the bottom of the core and thus flattened the axial power profile. The effect was a reduction in maximum DLOFC temperature by 44 deg. C. The simulations were made using the VSOP- 99/05 diffusion code. It was further shown that the results obtained are also applicable to the Chinese HTR-PM and the proposed strategies for further improvement can be expected to produce even much better results in Block Reactors than in Pebble Bed Reactors. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of New Reactor Core Configuration for Power Uprate - Fuel Reload & Heat Processing Analyses, Core Design, System Safety Assessments, and Fuel Performance Analyses

With the passage of the Infrastructure Investment and Jobs Act in 2021 and the Inflation Reduction Act (IRA) in 2022, the United States stands at a critical juncture for the future of nuclear power. These landmark policies provide significant support for clean energy initiatives, positioning nuclear power as a key component of the nation’s strategy to reduce carbon emissions and achieve energy security. This growing emphasis on nuclear energy is driven by the need for reliable, low-carbon power sources as the country transitions away from fossil fuels. Federal policy, along with increasing state-level support, is encouraging investment in nuclear technology advancements to meet these demands. Building new nuclear power plants (NPPs), however, presents significant challenges due to high costs and long construction timelines. As a result, increasing the power output of existing NPPs through power uprates has emerged as a more feasible and cost-effective strategy. One key area of advancement is the development of accident-tolerant fuel (ATF), such as chromium-coated zirconium alloy cladding, which offers enhanced material performance, enabling power uprates in light water reactors (LWRs). Given the growing demand for nuclear energy fueled by federal policies and state initiatives, it is essential to evaluate the feasibility and benefits of significant power uprates in existing pressurized water reactors (PWRs) using advanced fuel technologies. The introduction of ATF concepts opens new opportunities for safely and economically achieving these power increases. Assessing whether these innovations can support substantial power uprates while maintaining operational safety is crucial to maximizing the potential of the nation’s existing nuclear infrastructure. This project aims to explore how power uprates can be achieved by boosting reactor thermal power output and optimizing reactor core design, while ensuring the safety and economic viability of NPPs. Specifically, it will focus on demonstrating the technical and economic feasibility of power uprates in a PWR using low 5-10% enrichment uranium (LEU+) high burnup (HBU) fuel combined with ATF concepts. In fiscal year 2024 (FY24), the research and development focus on building foundational models and conducting multi-physics performance and safety analyses to support the power uprate. The findings of the study would be shared through LWRS Seasonal Meetings, conferences and workshops with utility companies and researchers. These also serve as a basis for further study of fuel reloading optimization with ATF claddings.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radioactive Waste Partitioning and Transmutation within Advanced Fuel Cycles: Achievements and Challenges

If nuclear power should become a sustainable source of energy, a safe, robust and acceptable solution must be pursued for existing and projected inventories of high-activity, long-lived radioactive waste. Remarkable progress in the last two decades has been made in the field of geological disposal. Some countries have reached important milestones and geological disposal (of spent fuel) is expected to start in 2020 in Finland and in 2022 in Sweden and in fact the licensing of the geological repositories in both countries is now entering into their final phases. In France disposal of Intermediate Level Wastes (ILW) and vitrified High Level Wastes (HLW) is expected to start around 2025, according to the roadmap defined by a Parliament Act in 2006. In this context, transmutation of part of the waste through use of advanced fuel cycles, probably feasible in the coming decades, has the potential of reducing the burden on the geological repository. This article presents the physical principle of transmutation and reviews several strategies of P&T (Partitioning and Transmutation). Many recent studies have demonstrated that the impact of P&T on geological disposal concepts is not overwhelmingly high. However, by reducing waste heat production a more efficient utilization of repository space is likely. Moreover, even if radionuclide release from the waste to the environment and related calculated doses to the population are only partially reduced by P&T, it is important to point out that a clear reduction of the actinide inventory in the High Level Waste definitely reduces risks arising from less probable evolutions of a repository, i.e. increase of actinide mobility in certain geochemical situations and radiological impact by human intrusion.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Primer on Motor Fuel Excise Taxes and the Role of Alternative Fuels and Energy Efficient Vehicles

Motor fuel taxes were established to finance our nation’s transportation infrastructure, yet evolving economic, political, and technological influences are constraining this ability. At the federal level, the Highway Trust Fund (HTF), which is primarily funded by motor fuel taxes, has become increasingly dependent on general fund contributions and short-term reauthorizations to prevent insolvency. As a result, there are discussions at both the federal and state levels in which stakeholders are examining the future of motor fuel excise taxes as well as the role of electric and alternative fuel vehicles in that future. On July 1, 2015, six states increased their motor fuel tax rates.

33 ADVANCED PROPULSION SYSTEMS↗

Overview of lower length scale model development for accident tolerant fuels regarding U 3 Si 2 fuel and FeCrAl cladding

U 3 Si 2 and FeCrAl have been proposed as fuel and cladding concepts, respectively, for accident tolerance fuels with higher tolerance to accident scenarios compared to UO 2 . However, a lot of key physics and material properties regarding their in-pile performance are yet to be explored. To accelerate the understanding and reduce the cost of experimental studies, multiscale modeling and simulation are used to develop physics-based materials models to assist engineering scale fuel performance modeling. In this report, the lower-length-scale efforts in method and material model development supported by the Accident Tolerance Fuel (ATF) high-impact-problem (HIP) under the NEAMS program are summarized. Significant progresses have been made regarding interatomic potential, phase field models for phase decomposition and gas bubble formation, and thermal conductivity for U 3 Si 2 fuel, and precipitation in FeCrAl cladding. The accomplishments are very useful by providing atomistic and mesoscale tools, improving the current understanding, and delivering engineering scale models for these two ATF concepts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The need for a characteristics-based approach to radioactive waste classification as informed by advanced nuclear fuel cycles using the fuel-cycle integration and tradeoffs (FIT) model

This study explores the impact of wastes generated from potential future fuel cycles and the issues presented by classifying these under current classification criteria, and discusses the possibility of a comprehensive and consistent characteristics-based classification framework based on new waste streams created from advanced fuel cycles. A static mass flow model, Fuel-Cycle Integration and Tradeoffs (FIT), was used to calculate the composition of waste streams resulting from different nuclear fuel cycle choices. Because heat generation is generally the most important factor limiting geological repository areal loading, this analysis focuses on the impact of waste form heat load on waste classification practices, although classifying by metrics of radiotoxicity, mass, and volume is also possible. Waste streams generated in different fuel cycles and their possible classification based on the current U.S. framework and international standards are discussed. It is shown that the effects of separating waste streams are neglected under a source-based radioactive waste classification system. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Assessment of SFR fuel pin performance codes under advanced fuel for minor actinide transmutation

Americium is a strong contributor to the long term radiotoxicity of high activity nuclear waste. Transmutation by irradiation in nuclear reactors of long-lived nuclides like {sup 241}Am is, therefore, an option for the reduction of radiotoxicity and residual power packages as well as the repository area. In the SUPERFACT Experiment four different oxide fuels containing high and low concentrations of {sup 237}Np and {sup 241}Am, representing the homogeneous and heterogeneous in-pile recycling concepts, were irradiated in the PHENIX reactor. The behavior of advanced fuel materials with minor actinide needs to be fully characterized, understood and modeled in order to optimize the design of this kind of fuel elements and to evaluate its performances. This paper assesses the current predictability of fuel performance codes TRANSURANUS and GERMINAL V2 on the basis of post irradiation examinations of the SUPERFACT experiment for pins with low minor actinide content. Their predictions have been compared to measured data in terms of geometrical changes of fuel and cladding, fission gases behavior and actinide and fission product distributions. The results are in good agreement with the experimental results, although improvements are also pointed out for further studies, especially if larger content of minor actinide will be taken into account in the codes. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Temperature Rise on Liner Surfaces of Fuel Cell Electric Vehicle Tanks during Fueling Process

Herein, the temperature of the inner tank walls, or plastic liners, of composite pressure tanks in fuel cell electric vehicles during fueling using three‐dimensional computational fluid dynamics (CFD) models is evaluated. The liner materials are limited to 85.0 °C to prevent thermal stress causing material failure that would result in a hydrogen leak. Therefore, the temperature of hydrogen gas must be limited to below 85.0 °C during the fueling process as dictated by the current fueling protocol. However, there are limited experimental or simulation data confirming that the temperature changes do not exceed the threshold. Herein, the liner temperatures with CFD tank models for two sizes of type IV tanks representative of the upper and lower system bounds that are close to the SAE J2601 fueling protocol (36.0 and 244.0 L) are evaluated. First, each model's reliability is validated with experimental data and then analyzed, and the data are used to evaluate the maximum hydrogen and liner temperatures under real‐world fueling conditions. The evaluation shows that the maximum liner surface temperature of each tank model is at least 7 °C lower than that of the hydrogen. Additionally, there is at least 12 °C difference found between the upper limit and actual liner temperatures.

33 ADVANCED PROPULSION SYSTEMS↗

A model for droplet heating and evaporation of water-in-oil emulsified fuel

Water-in-oil (W/O) emulsified fuel is a promising alternative fuel by inducing flash boiling of water at high temperature that can improve the atomization of fuel spray. The heating and evaporation process of emulsified fuel droplet is affected by the diffusion and coalescence of small dispersed water droplets in oil during the heating. In this study, a model is developed for the droplet heating and evaporation of W/O emulsified fuel with these key physics considered. The diffusivity of dispersed water droplets in oil is calculated using the Stokes-Einstein equation. The deactivation temperature of surfactant is selected as a criterion for the water coalescence since the water coalescence is due to the deactivation of surfactant. The process of water coalescence is simplified that the dispersed water droplets coalesce into one single water sub-droplet at the center of the oil droplet instantly as the droplet temperature reaches the deactivation temperature of surfactant. The model is validated against experimental data of single droplet under different heating temperatures, surfactant concentrations, and sizes of dispersed water droplets. Based on the proposed model, the effects of fuel properties and heating conditions on the droplet heating and evaporation are analyzed.

Droplet coalescence↗

Production and Fuel properties of Iso-Olefins with Controlled Molecular Structure and Obtained from Butene Oligomerization

The ability to control the molecular structure (e.g., degree of branching) of iso-olefins produced from oligomerizing light olefins is a valuable tool for tuning the final compositions of hydrocarbon fuels and targeting specific fuel properties. In this study, we demonstrated that the degree of branching of iso-olefins obtained from butene(s) oligomerization can be controlled by tuning process conditions (i.e., temperature, weight hourly space velocity [WHSV], and nature of butene feedstock) and by choosing the proper catalyst (i.e., Amberlyst-36 vs. Y/ZSM-22). In this study, we produced three types of iso-olefin mixtures: 1) a methyl-heptenes rich (74 wt.%) mixture, 2) dimethyl-hexenes rich (80–96 wt.%) mixtures, and 3) highly branched (i.e., more than three methyl substitutions) iso-olefins rich (>50 wt.%) mixtures. While dimethyl-hexenes are preferentially formed at lower temperatures (60–100°C) and WHSV (i.e., 2 hr-1), methyl-heptenes are favorably produced at higher temperatures (>100°C) and WHSVs (i.e., 7 hr-1) over Amberlyst-36. The use of either 1-butene or 2-butene as feedstock resulted in liquid products with similar branching because facile intramolecular isomerization occurs prior to oligomerization. However, the use of isobutylene feedstock forms a significantly more branched olefin product. The formation of highly branched iso-olefins also is favored at higher temperature (140°C) over Amberlyst-36. Using Y/ZSM-22 instead of Amberlyst-36 allowed preferential formation of less-branched methyl-heptenes. For each type of iso-olefins mixture, we determined fuel properties including research octane number (RON), motor octane number (MON), and octane sensitivity (S), which is the difference between RON and MON. We found that not only RON and MON but also S values increased with the degree of branching of these complex mixtures of iso-olefins. The highest RON of 99.7 and S value of 9.3 were obtained for a mixture of highly branched iso-olefins.

Dagle, Vanessa↗

TRISO-Fuel Element Performance Modeling for the Hybrid LIFE Engine with Pu Fuel Blanket

A TRISO-coated fuel thermo-mechanical performance study is performed for the hybrid LIFE engine to test the viability of TRISO particles to achieve ultra-high burnup of a weapons-grade Pu blanket. Our methodology includes full elastic anisotropy, time and temperature varying material properties for all TRISO layers, and a procedure to remap the elastic solutions in order to achieve fast fluences up to 30 x 10{sup 25} n {center_dot} m{sup -2} (E > 0.18 MeV). In order to model fast fluences in the range of {approx} 7 {approx} 30 x 10{sup 25} n {center_dot} m{sup -2}, for which no data exist, careful scalings and extrapolations of the known TRISO material properties are carried out under a number of potential scenarios. A number of findings can be extracted from our study. First, failure of the internal pyrolytic carbon (PyC) layer occurs within the first two months of operation. Then, the particles behave as BISO-coated particles, with the internal pressure being withstood directly by the SiC layer. Later, after 1.6 years, the remaining PyC crumbles due to void swelling and the fuel particle becomes a single-SiC-layer particle. Unrestrained by the PyC layers, and at the temperatures and fluences in the LIFE engine, the SiC layer maintains reasonably-low tensile stresses until the end-of-life. Second, the PyC creep constant, K, has a striking influence on the fuel performance of TRISO-coated particles, whose stresses scale almost inversely proportional to K. Obtaining more reliable measurements, especially at higher fluences, is an imperative for the fidelity of our models. Finally, varying the geometry of the TRISO-coated fuel particles results in little differences in the scope of fuel performance. The mechanical integrity of 2-cm graphite pebbles that act as fuel matrix has also been studied and it is concluded that they can reliable serve the entire LIFE burnup cycle without failure.

42 ENGINEERING↗

Standardized protocols for evaluating platinum group metal-free oxygen reduction reaction electrocatalysts in polymer electrolyte fuel cells

Platinum group metal (PGM)-free electrocatalysts for the oxygen reduction reaction at the polymer electrolyte fuel cell cathode have shown substantial improvements in activity—especially those derived from transition metals, nitrogen and carbon. However, their stability and durability remain insufficient. A key to enabling future improvements and performance comparisons lies in the development of test protocols that are relevant to the operating conditions of the fuel cell cathode, can be completed within a reasonable time and are ubiquitously adopted. Here we propose and validate such protocols, designed with special attention to typical catalyst degradation mechanisms of PGM-free catalysts. The results of the cross-laboratory validation study using two different catalysts attest to the strength and feasibility of the proposed approach. We hope that the information provided here can serve as a broad and effective platform for assessing the performance and durability of PGM-free catalysts for polymer electrolyte fuel cells.

25 ENERGY STORAGE↗

Phases 1 & 2—Coal-Based Oxy-Fuel System Evaluation and Combustor Development and Phase 2A—Recovery Act: Oxy-Fuel Turbomachinery Development for Energy Intensive Industrial Applications (Final Report, Rev.1)

Clean Energy Systems, Inc. (CES) partnered with the U.S. Department of Energy’s National Energy Technology Laboratory in 2005 to study and develop a competing technology for use in future fossil-fueled power generation facilities that could operate with near zero emissions. CES’s background in oxy-fuel (O-F) rocket technology lead to the award of Cooperative Agreement DE-FC26-05NT42645, “Coal-Based Oxy-Fuel System Evaluation and Combustor Development,” where CES was to first evaluate the potential of these O-F power cycles, then develop the detailed design of a commercial-scale O-F combustor for use in these clean burning fossil-fueled plants. Throughout the studies, CES found that in order to operate at competitive cycle efficiencies a high-temperature intermediate pressure turbine was required. This led to an extension of the Agreement for, “Oxy-Fuel Turbomachinery Development for Energy Intensive Industrial Applications” where CES was to also develop an intermediate-pressure O-F turbine (OFT) that could be deployed in O-F industrial plants that capture and sequester >99% of produced CO 2 , at competitive cycle efficiencies using diverse fuels. The following report details CES’ activities from October 2005 through March 2013, to evaluate O-F power cycles, develop and validate detailed designs of O-F combustors (main and reheat), and to design, manufacture, and test a commercial-scale OFT, under the three-phase Cooperative Agreement.

01 COAL, LIGNITE, AND PEAT↗

Co-Optimization of Fuels & Engines: Fuel Blendstocks with the Potential to Optimize Future Gasoline Engine Performance; Identification of Five Chemical Families for Detailed Evaluation

The U.S. Department of Energy's (DOE's) Co-Optimization of Fuels & Engines (Co-Optima) initiative is conducting the early-stage research needed to accelerate the market introduction of advanced fuel and engine technologies. The research includes both spark-ignition (SI) and compression-ignition (CI) combustion approaches, targeting applications that impact the entire on-road fleet (light-, medium-, and heavy-duty vehicles). The initiative's major goals include significant improvements in vehicle fuel economy, lower-cost pathways to reduce emissions, and leveraging diverse U.S. fuel resources. A key objective of Co-Optima's research is to identify new blendstocks that enhance current petroleum blending components, increase blendstock diversity, and provide refiners with increased flexibility to blend fuels with the key properties required to optimize advanced internal combustion engines. This report identifies eight representative blendstocks from five chemical families that have demonstrated the potential to increase boosted SI engine efficiency, meet key fuel quality requirements, and be viable for production at commercial scale by 2025-2030.

33 ADVANCED PROPULSION SYSTEMS↗