Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fracturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Fracture toughness of schist, amphibolite, and rhyolite from the Sanford Underground Research Facility (SURF), Lead, South Dakota

The Cracked Chevron Notched Brazilian Disc (CCNBD) method was selected for Mode I fracture toughness tests on Poorman schist, Yates amphibolite, and rhyolite dikes from the EGS Collab site at the SURF in Lead, South Dakota. The effects of lithology, anisotropy, and loading rate were investigated. Fracture toughness was greatest in amphibolite, with schist and rhyolite having similar toughness values ($K$ amphibolite > $K$ rhyolite ≈ $K$ schist ). The effects of anisotropy on fracture toughness were investigated in the foliated schist samples. Schist samples were prepared in three geometries (divider, arrester, and short transverse) which controlled how the fracture would propagate relative to foliations. The divider geometry was strongest and short transverse geometry was the weakest ($K$ divider > $K$ arrester > $K$ shorttransverse ). Fracture toughness was observed to decrease with decreasing loading rate. Optical and SEM microscopy revealed that for the short transverse geometry, fractures tended to propagate along grain boundaries, whereas in arrester and divider geometries fractures tended to propagate through grains. In foliated samples, the tortuosity of the fracture observed in thin section was greater in arrester and divider geometries than in short transverse geometries.

58 GEOSCIENCES↗
DOE OSTI2025

Mechanistic understanding of carbon mineralization in fracture systems using microfluidics

Carbon mineralization in mafic and ultramafic rocks presents an opportunity for permanent carbon storage in the Earth's subsurface. However, due to their lower permeability, pre-existing fracture networks are key for mineralization to occur. Therefore, to fully develop this technology, a mechanistic understanding of the mineralization behavior in fractures with the consideration of hydrodynamic components is required. We use high-pressure microfluidics to investigate key mechanisms influencing dissolution–precipitation in a fracture network. The experiments were conducted in micromodels made of natural rocks with a comb-shaped flow channel to mimic a fracture network. This enabled studying the effect of injection rate on coupled dissolution–precipitation in advection and diffusion-dominated flow paths. We used gypsum carbonation as an analog reaction to allow for realistic experimental time frames due to its rapid reaction kinetics. The experimental work is coupled with high-fidelity numerical simulations to enhance our understanding of the parameters affecting the mineralization reaction. Our results demonstrate the importance of flow rate on the rate and nature of the gypsum carbonation reaction revealing that higher flow rates enable deeper penetration of the mineral precipitation front into the dead-end channels. This is an important finding since for sustained mineralization in a fracture network, precipitation in dead-ends while still allowing for flowing fractures is critical. Detailed characterization of the precipitates showed that lower flow rates led to porous and loose precipitates in the form of aragonite while higher flow rates mimicked supersaturation behavior leading to the formation of calcite. The reactive transport simulations further demonstrated the significance of flow velocity in advection-dominated channels to influence the efficiency of carbon mineralization in diffusion-dominated channels, potentially clogging of dead-end channels. These findings highlight the need for coupling chemical, mechanical, and hydrodynamic processes to evaluate the nature and extent of carbon mineralization in fractured media critical for permanent storage in mafic and ultramafic formations. This research further highlights the need for more investigation in potential subsurface fracture generation techniques to aid carbon mineralization.

25 ENERGY STORAGE↗
DOE OSTI2024

Investigating In-Situ Fracture Behaviors of Polymer Pipeline Materials in Hydrogen and Hydrogen-Methane Blended Gas Environments

To reduce carbon emissions, the US natural gas infrastructure is seen as a primary solution for efficiently transporting hydrogen gas. Blending hydrogen gas with natural gas and transporting it across a national infrastructure could save significant infrastructure costs. To properly operate the infrastructure under the new gas system, it is critical to understand material compatibility with hydrogen under various conditions. The Blended Gas CRADA, a Hyblend project, is established to determine the material compatibility of existing natural gas pipes with hydrogen gas. In this study, we investigate the in-plane fracture behaviors of MDPEMarlex and HDPEGDB exposed to hydrogen and hydrogen-methane blended gas. Single-edge notch bending geometry is used. All tests are executed in-situ with the gas environment. The experimental results show a significant effect of the gas environment on HDPEGDB specimens, reducing 5% (H2) to 42% (Blended gas) of specific fracture energy compared to non-aged specimens. For the MDPEMarlex, the effects of the gas environment have increased the specific fracture energy by 10% (H2) to 15% (Blended gas). Fracture surfaces of the tested samples are observed using an electronic microscope. The in-plane fracture surface of HDPEGDB shows a pronounced dimple fracture pattern after exposure to hydrogen and blended gas. The expanded fracture pattern contributes to lower the specific fracture energy. These observations provide critical information for validating polymer pipeline materials when interact with hydrogen and hydrogen-blend gas.

Ko, Seunghyun↗
DOE OSTI2021

Investigating Fracture Network Deformation Using Noble Gas Release

We investigate deformation mechanics of fracture networks in unsaturated fractured rocks from subsurface conventional detonation using dynamic noble gas measurements and changes in air permeability. We dynamically measured the noble gas isotopic composition and helium exhalation of downhole gas before and after a large subsurface conventional detonation. These noble gas measurements were combined with measurements of the subsurface permeability field from 64 discrete sampling intervals before and after the detonation and subsurface mapping of fractures in borehole walls before well completion. We saw no observable increase in radiogenic noble gas release from either an isotopic composition or a helium exhalation point of view. Large increases in permeability were observed in 13 of 64 discrete sampling intervals. Of the sampling intervals which saw large increases in flow, only two locations did not have preexisting fractures mapped at the site. Given the lack of noble gas release and a clear increase in permeability, we infer that most of the strain accommodation of the fractured media occurred along previously existing fractures, rather than the creation of new fractures, even for a high strain rate event. These results have significant implications for how we conceptualize the deformation of rocks with fracture networks above the percolation threshold, with application to a variety of geologic and geological engineering problems.

Gardner, W. Payton↗
DOE OSTI2021

Characterization of an electrically conductive proppant for fracture diagnostics

Fracture diagnosis with electromagnetic (EM) and electrical tools requires proppants with high electrical conductivity and mechanical strength. Lab measurements of the electrical and hydraulic conductivity of proppants are critical for selecting the best candidates. Such measurements greatly benefit simulations, field tests, and the ultimate application of such proppants in the field. To that end, a new lab protocol is developed for measuring the electrical and hydraulic conductivity of proppants. The lab setup, which mainly includes a resistivity core holder and a Hassler sleeve core holder, allows for simulation of realistic pressure and temperature conditions when making measurements. Petroleum coke (PC) is proposed as a candidate proppant because of its widespread availability and low cost. Lab measurements show that the effective electrical conductivity of pure PC in a model fracture is approximately 5000 S/m, under a closure stress greater than [Formula: see text] (4000 psi). When PC is mixed with sand, the effective electrical conductivity of the mixture decreases with an increasing weight percentage of sand. Although sand degrades the contact between PC particles, the electrical conductivity stays reasonably high (approximately 1700 S/m) when 50% sand is added. Hydraulic conductivity measurements show that when a fracture is propped with pure PC, the measured fracture conductivity is greater than [Formula: see text] ([Formula: see text]) (dimensionless fracture conductivity greater than 100 for a shale with [Formula: see text] or 100 nD permeability) under a confining pressure of [Formula: see text] (6000 psi). This means that a fracture propped with PC is infinitely conductive in a typical shale formation. When sand is added, the fracture’s hydraulic conductivity becomes even higher, which clearly shows PC’s ability of sustaining high stresses. The proposed protocol provides a robust and effective method that can be generalized for lab testing for other candidate proppants. The data presented clearly show that PC has the potential for field-scale applications in EM hydraulic fracture diagnostics.

Geochemistry & Geophysics↗
DOE OSTI2018

Environmental Impact Analysis on the Hydraulic Fracture Test Site (HFTS)

Objective The Hydraulic Fracture Test Site (HFTS) provided a platform to test new extraction and production techniques and technologies to understand fracture geometry and increase the efficiency of shale hydrocarbon production. Eleven test wells were drilled in the Upper and Middle Wolfcamp formations, hydraulically fractured, and produced. Air quality, groundwater quality, and produced water chemistry and microbiology were monitored through the duration of the field experiment and one year into production. Methods BTEX, methane, VOCs, SOx, NOx, and PM 10 were measured 1,000 ft up-wind and 1,000 ft down-wind of the HFTS experiment before operations began, during hydraulic fracturing, flowback, and several months into production to evaluate operational impact on local air quality. The underlying Edward-Trinity Plateau aquifer was monitored using 5 groundwater wells within 2 miles of the HFTS pad; BTEX, methane, petroleum hydrocarbons, and a comprehensive suite of anions and metals were analyzed from samples taken before operations began, during hydraulic fracturing, flowback, and one year after production. Water produced from 3 of the 11 HFTS wells was analyzed for chemical and microbiological properties 1.5 years into production. Observations There was no significant impact to air quality from HFTS operations, although elevated BTEX concentrations were measured 1,000 ft. away from the well-pads during the flowback period. We detected no migration of hydrocarbon or fracture fluid chemical migration into the Edward-Trinity Plateau aquifer. Source waters used for hydraulic fracturing contained naturally occurring high concentrations (~500ppm) of sulfate. Rapid microbially induced corrosion was detected in several wells, leading to biocide dosing. Microbiological populations were significantly altered by biocide treatment, but still continued to increase in population size six months after application. Significance After hydraulic fracturing, detailed chemical and microbiological analysis provides evidence for microbiologicallymediated sub-surface transformations of supplied sulfate and organic carbon into sulfides. This report discusses air quality, water quality, and produced water analytical results for the HFTS experiment and further implications for the unconventional oil and gas industry.

Eisenlord, Sarah↗
DOE OSTI2016

Seismic Fracture Characterization Methodologies for Enhanced Geothermal Systems

Executive Summary The overall objective of this work was the development of surface and borehole seismic methodologies using both compressional and shear waves for characterizing faults and fractures in Enhanced Geothermal Systems. We used both surface seismic and vertical seismic profile (VSP) methods. We adapted these methods to the unique conditions encountered in Enhanced Geothermal Systems (EGS) creation. These conditions include geological environments with volcanic cover, highly altered rocks, severe structure, extreme near surface velocity contrasts and lack of distinct velocity contrasts at depth. One of the objectives was the development of methods for identifying more appropriate seismic acquisition parameters for overcoming problems associated with these geological factors. Because temperatures up to 300º C are often encountered in these systems, another objective was the testing of VSP borehole tools capable of operating at depths in excess of 1,000 m and at temperatures in excess of 200º C. A final objective was the development of new processing and interpretation techniques based on scattering and time-frequency analysis, as well as the application of modern seismic migration imaging algorithms to seismic data acquired over geothermal areas. The use of surface seismic reflection data at Brady's Hot Springs was found useful in building a geological model, but only when combined with other extensive geological and geophysical data. The use of fine source and geophone spacing was critical in producing useful images. The surface seismic reflection data gave no information about the internal structure (extent, thickness and filling) of faults and fractures, and modeling suggests that they are unlikely to do so. Time-frequency analysis was applied to these data, but was not found to be significantly useful in their interpretation. Modeling does indicate that VSP and other seismic methods with sensors located at depth in wells will be the most effective seismic tools for getting information on the internal structure of faults and fractures in support of fluid flow pathway management and EGS treatment. Scattered events similar to those expected from faults and fractures are seen in the VSP reported here. Unfortunately, the source offset and well depth coverage do not allow for detailed analysis of these events. This limited coverage also precluded the use of advanced migration and imaging algorithms. More extensive acquisition is needed to support fault and fracture characterization in the geothermal reservoir at Brady's Hot Springs. The VSP was effective in generating interval velocity estimates over the depths covered by the array. Upgoing reflection events are also visible in the VSP results at locations corresponding to reflection events in the surface seismic. Overall, the high temperature rated fiber optic sensors used in the VSP produced useful results. Modeling has been found useful in the interpretation of both surface reflection seismic and VSP data. It has helped identify possible near surface scattering in the surface seismic data. It has highlighted potential scattering events from deeper faults in the VSP data. Inclusion of more detailed fault and fracture specific stiffness parameters are needed to fully interpret fault and fracture scattered events for flow properties (Pyrak-Nolte and Morris, 2000, Zhu and Snieder, 2002). Shear wave methods were applied in both the surface seismic reflection and VSP work. They were not found to be effective in the Brady's Hot Springs area. This was due to the extreme attenuation of shear waves in the near surface at Brady's. This does not imply that they will be ineffective in general. In geothermal areas where good shear waves can be recorded, modeling suggests they should be very useful for characterizing faults and fractures.

15 GEOTHERMAL ENERGY↗
DOE OSTI2018

Literature Review and Analysis of Waterless Fracturing Methods

This report provides a brief literature review and analysis of several waterless fracturing methods. The methods included in this report are: Liquid CO2/Sand Fracturing; Straight Nitrogen Based Fracturing; Liquefied Petroleum Gas (LPG) Fracturing; Liquefied Natural Gas (LNG) Fracturing; as well as Explosives and Propellant-Based Fracturing. Additional non-water carrier fluids are also identified. A discussion on CO2-Foam Fracturing is given in the separate LBNL report mentioned above (Wan, 2017). The strengths and limitations of each non-water fracture stimulation carrier fluid are described below, and insights are provided on the characteristics of geologic formations amenable to the use of each fluid.

58 GEOSCIENCES↗
DOE OSTI2020

CO2 injection with fracturing in geomechanically protected caprock: Task 6 of LLNL's Research Activities to Support DOE's Carbon Storage Program (FWP-FEW0191) (Final Technical Report)

Conventional principles of the design and operation of geologic carbon storage (GCS) require injecting CO 2 below the caprock fracturing pressure to ensure the integrity of the storage complex. In non-ideal storage reservoirs with relatively low permeability, modest injection rates can lead to pressure buildup and hydraulic fracturing of the reservoir and caprock. While the GCS community has generally viewed hydraulic fractures as a key risk to storage integrity, the actual behavior of a caprock hydraulic fracture, particularly from a geomechanical perspective, has not been thoroughly studied. The prevailing method of treating a hydraulic fracture as a high-permeability wing of the storage reservoir might have resulted in erroneous understanding of caprock hydraulic fracture behavior. Comprehensive analyses of monitoring data from the In Salah project suggested that one or more hydraulic fractures may have been created in the reservoir and lower caprock system during injection operations, but did not cause detectable leakage of CO 2 out of the storage complex. This observation coincides with a well-known phenomenon in the oil and gas industry: sedimentary rock formations have many inherent features that naturally protect the formations from unbounded vertical growth of hydraulic fractures.

58 GEOSCIENCES↗
DOE OSTI2022

Controlling Sustainability of Hydraulic Fracture Permeability in Ductile Shales

Hydraulic fracturing technology, along with horizontal drilling and associated completion technologies, dramatically increased US oil and gas production, by increasing the permeability of tight shales and allowing for cost-effective extraction of trapped hydrocarbons. For efficient and economical production, the targeted shale has to be fractured easily (i.e., good ‘frackability’), but also the permeability of induced fractures have to be sustained during production (good ‘sustainability’). For these reasons, currently, ductile shale with high clay content (>~40%) is difficult to exploit as a hydrocarbon resource, although hydrocarbons can still be found in it. Good frackability, high-TOC, low-clay-content resource shales—the ‘low-hanging fruit’—will be depleted, and we need to develop tools that allow tapping into currently underutilized, clay-rich ductile shales. This research project aims (1) to understand the behavior of fractures in clay-rich, ductile (and sometimes swelling) shales and (2) to begin to develop technologies for efficient and economical production from such shales. With these objectives, we examine time-dependent, coupled mechanical-hydrological behavior of open and proppant-filled fractures within different types of shales. In the preceding project, the focus of the research was to understand the behavior of the fractures and to predict their permeability changes due to fracture closure from shale matrix deformation and proppant embedment. In the current project, we investigate the possibility of chemically manipulating the sustainability of hydraulic fractures in ductile shales—specifically by altering the proppant-embedding behavior—via chemical means, at different stages of oil and gas production.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2024

Fracture resistance of vintage cast iron in gaseous hydrogen

In an effort to decarbonize legacy energy systems, several projects around the world are exploring alternatives to natural gas. Gaseous hydrogen is proposed as a carbon-free fuel to displace natural gas in existing legacy natural gas distribution systems, some of which continue to operate after 100 years (or more) in service. These systems, particularly in older industrial centers, contain cast iron pipe. However, the fracture resistance of most metals is degraded in gaseous hydrogen environments. This study evaluated the fracture resistance of several legacy cast iron pipe materials while exposed to gaseous hydrogen. Measurements were performed in three environments: air, a gas mixture with hydrogen partial pressure of 1 bar and pure hydrogen with a partial pressure of 34 bar. Although cast iron is generally considered a low ductility metal, elastic-plastic fracture methods are needed to assess the fracture resistance of the relatively small specimens that can be extracted from legacy pipe. Hydrogen reduced the fracture resistance of these cast iron materials by 10-40%. In air, the fracture resistance was determined to be as high as 21 MPa m 1/2 , whereas in gaseous hydrogen at pressure of about 1 bar the fracture resistance was as low as 13 MPa m 1/2 . Additional modest degradation of the fracture resistance was assessed at higher partial pressure (as low as 12 MPa m 1/2 ).

08 HYDROGEN↗
DOE OSTI2026

Development, Monitoring, and Control of Fracture Thermal Energy Storage (FTES) in Crystalline Rock Formations (DEMO-FTES) (CRADA Final Report)

The DEMO-FTES project sought to demonstrate the thermal efficiency of fracture thermal energy storage (FTES) through numerical simulations, laboratory and meso-scale field tests. A detailed dimensional and scaling analysis was performed to identify key parameters and how they can be most effectively scaled to the laboratory and decameter scale. Numerical models were developed and used for three purposes: 1. Before field experiments, numerical modelling can be used to estimate fracture properties based on previous data from the EGS Collab experiment and then predict thermal hydrological behaviors of the fracture system with hot water injection/withdrawal, therefore, help to design the experiments (e.g., to decide the duration of the cycles based on the flow rate the pump can provide, and the estimated fracture properties); 2. After the field experiment, to estimate the system properties during the experiment (as the size and shape of a fracture could change over time), and understand why system performance is different than what has been predicted, i.e., to help understand the meso-scale test; and, 3. To model the lab experiments and estimate fracture properties and storage efficiency. Ultimately, the experiment and numerical models could shed light on the processes and uncertainty happening during fracture activation and help understand the scaling between lab and field test, and finally, the design and optimization of potential fracture thermal energy storage systems.

25 ENERGY STORAGE↗
DOE OSTI2021

Fracture Mechanics—Theory, Modeling and Applications

The field of fracture mechanics was developed during the throes of World War II, and since then, it has been a very active area of research. This is a very energetic and vibrant field because fracture processes are relevant for a vast range of engineering applications spanning different temporal and length scales. Depending on the application, material fracture and fragmentation may be either a desirable feature (for example, for the purpose of hydraulic fracturing operations), or something that is to be avoided at all costs (for example, in key components of mechanical systems). In some other instances, fractures are already present and must be accommodated through novel design (for example, in the case of earthquake ruptures occurring in the Earth’s crust). Because of this wide spectra of motivation, there is a continuous need for the fracture mechanics research community to gain more insight on how fractures are created, evolve, and interact with themselves and with material microstructures. In addition, there are still many remaining questions about how fracture propagation, growth, and interaction impact overall material behavior, and how to develop accurate models to predict this behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Insights into the hydro-mechanical behavior of a decimeter-scale fracture using the mini-SIMFIP probe

ABSTRACT: Understanding hydro-mechanical couplings in fractured rocks is essential for predicting the rock mass response during high-pressure fluid injection, including the stimulation of enhanced geothermal systems. However, fluid-driven fracture dislocations are challenging to measure due to the need for local displacement data at high fluid pressures. In this study, fluid-driven displacement across a decimeter-scale laboratory fracture was investigated using the mini-SIMFIP (step rate injection method for fracture in-situ properties) probe, which is a smaller version of the SIMFIP tool (Guglielmi et al., 2014). The mini-SIMFIP probe is able to resolve the full 3D displacement vector of a fracture. The probe was installed in one of two boreholes across a decimeter-scale saw-cut granite fracture. Two pressure step injection tests were conducted under the same isotropic stress conditions. By varying injection between the boreholes, we estimated the aperture profile across the fracture. The results show a consistent pressure-dependent opening as long as steady-state flow was maintained. At a certain pressure step, steady-state conditions were no longer achievable and the fracture opened rapidly. The pressure-opening relationship diverged between the two tests and indicated a homogenization of the aperture profile and an increase in the non-linearity of the flow regime.

Osten, J↗
NASA NTRS1974

An analysis of fracture trace patterns in areas of flat-lying sedimentary rocks for the detection of buried geologic structure

Two study areas in a cratonic platform underlain by flat-lying sedimentary rocks were analyzed to determine if a quantitative relationship exists between fracture trace patterns and their frequency distributions and subsurface structural closures which might contain petroleum. Fracture trace lengths and frequency (number of fracture traces per unit area) were analyzed by trend surface analysis and length frequency distributions also were compared to a standard Gaussian distribution. Composite rose diagrams of fracture traces were analyzed using a multivariate analysis method which grouped or clustered the rose diagrams and their respective areas on the basis of the behavior of the rays of the rose diagram. Analysis indicates that the lengths of fracture traces are log-normally distributed according to the mapping technique used. Fracture trace frequency appeared higher on the flanks of active structures and lower around passive reef structures. Fracture trace log-mean lengths were shorter over several types of structures, perhaps due to increased fracturing and subsequent erosion. Analysis of rose diagrams using a multivariate technique indicated lithology as the primary control for the lower grouping levels. Groupings at higher levels indicated that areas overlying active structures may be isolated from their neighbors by this technique while passive structures showed no differences which could be isolated.

Podwysocki, M. H.↗
NASA NTRS1980

Fractures on Europa - Possible response of an ice crust to tidal deformation

The surface of Europa contains a planetwide system of low albedo lineaments which have been interpreted as fractures in an icy crust. The pattern of fractures on the surface consists of radial and concentric fractures having the general appearance of tension cracks within a region near the antipode of the sub-Jupiter point. Outside this region, linear fractures intersect at angles near 60 deg, suggesting that they are conjugate shear fractures. The orientation of this pattern on the surface suggests that a principal axis of the deformation that produced the fractures was approximately radial to Jupiter. Fracturing may thus be consistent with an origin due to cyclical tidal deformation resulting from orbital eccentricity. Orbital eccentricity related to a relatively recent establishment of orbital resonance among the Galilean satellites may explain the presence of fractures in a relatively young, lightly cratered planetary surface.

Helfenstein, P.↗
NASA NTRS1987

Geometry and relative age of large patterned fractures in southern Acidalia Planitia, Mars

Extraordinary patterned fractures occur in Elysium, Utopia, and Acidalia Planitiae of Mars. Theories as to their origin range from permafrost patterning to tectonic fracturing. Recent studies indicate the patterned fractures may be a surface reflection of rough, buried terrane in which fracturing occurs as a result of differential compaction. The patterned terrane in the southern portion of the Acidalia region (MC4-SE, MC4-SC) is being studied to determine its age relative to other terranes and events, and to constrain models for the origin of the fractures. Fracturing in this area occurs between 5 and 25 degrees west longitude and 37 and 50 degrees north latitude. Many fracture patterns are roughly polygonal, with polygons ranging in size from approximately 11 to 32 km in diameter. Fracture traces range from the limit of resolution (10's of meters) to 35 km in length.

Borrello, Murray C.↗
NASA NTRS1988

Microstructural effects on fracture toughness of polycrystalline ceramics in combined mode I and mode II loading

Fracture toughness of polycrystalline alumina and ceria partially-stabilized tetragonal zirconia (CeO2-TZP) ceramics were assessed in combined mode I and mode II loading using precracked disk specimens in diametral compression. Stress states ranging from pure mode I, combined mode I and mode II, and pure mode II were obtained by aligning the center crack at specific angles relative to the loading diameter. The resulting mixed-mode fracture toughness envelope showed significant deviation to higher fracture toughness in mode II relative to the predictions of the linear elastic fracture mechanics theory. Critical comparison with corresponding results on soda-lime glass and fracture surface observations showed that crack surface resistance arising from grain interlocking and abrasion was the main source of the increased fracture toughness in mode II loading of the polycrystalline ceramics. The normalized fracture toughness for pure mode II loading, (KII/KIc), increased with increasing grain size for the CeO2-TZP ceramics. Quantitative fractography confirmed an increased percentage of transgranular fracture of the grains in mode II loading.

Singh, D.↗