Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FREE OSCILLATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Optical communications and a comparison of optical technologies for a high data rate return link from Mars

The important principles of direct- and heterodyne-detection optical free-space communications are reviewed. Signal-to-noise-ratio (SNR) and bit-error-rate (BER) expressions are derived for both the direct-detection and heterodyne-detection optical receivers. For the heterodyne system, performance degradation resulting from received-signal and local oscillator-beam misalignment and laser phase noise is analyzed. Determination of interfering background power from local and extended background sources is discussed. The BER performance of direct- and heterodyne-detection optical links in the presence of Rayleigh-distributed random pointing and tracking errors is described. Finally, several optical systems employing Nd:YAG, GaAs, and CO2 laser sources are evaluated and compared to assess their feasibility in providing high-data-rate (10- to 1000-Mbps) Mars-to-Earth communications. It is shown that the root mean square (rms) pointing and tracking accuracy is a critical factor in defining the system transmitting laser-power requirements and telescope size and that, for a given rms error, there is an optimum telescope aperture size that minimizes the required power. The results of the analysis conducted indicate that, barring the achievement of extremely small rms pointing and tracking errors (less than 0.2 microrad), the two most promising types of optical systems are those that use an Nd:YAG laser (lambda = 1.064 microns) and high-order pulse position modulator (PPM) and direct detection, and those that use a CO2 laser (lambda = 10.6 microns) and phase shifting keying homodyne modulation and coherent detection. For example, for a PPM order of M = 64 and an rms pointing accuracy of 0.4 microrad, an Nd:YAG system can be used to implement a 100-Mbps Mars link with a 40-cm transmitting telescope, a 20-W laser, and a 10-m receiving photon bucket. Under the same conditions, a CO2 system would require 3-m transmitting and receiving telescopes and a 32-W laser to implement such a link. Other types of optical systems, such as a semiconductor laser systems, are impractical in the presence of large rms pointing errors because of the high power requirements of the 100-Mbps Mars link, even when optimal-size telescopes are used.

Spence, Rodney L.↗
NASA NTRS2002

A Study of Standing Pressure Waves Within Open and Closed Acoustic Resonators

The first section of the results presented herein was conducted on an axisymmetric resonator configured with open ventilation ports on either end of the resonator, but otherwise closed and free from obstruction. The remaining section presents the results of a similar resonator shape that was closed, but contained an axisymmetric blockage centrally located through the axis of the resonator. Ambient air was used as the working fluid. In each of the studies, the resonator was oscillated at the resonant frequency of the fluid contained within the cavity while the dynamic pressure, static pressure, and temperature of the fluid were recorded at both ends of the resonator. The baseline results showed a marked reduction in the amplitude of the dynamic pressure waveforms over previous studies due to the use of air instead of refrigerant as the working fluid. A sharp reduction in the amplitude of the acoustic pressure waves was expected and recorded when the configuration of the resonators was modified from closed to open. A change in the resonant frequency was recorded when blockages of differing geometries were used in the closed resonator, while acoustic pressure amplitudes varied little from baseline measurements.

Daniels, C.↗
NASA NTRS1970

Leading-edge pressure measurements of airfoil vortex interaction

Experimental pressure-differential measurements made at 10% chord of an airfoil-vortex interaction are presented. A line vortex was oscillated over an airfoil perpendicular to the span and parallel to the chord. The pressure time history was recorded in order to show the sharp pressure pulses resulting from the bursting of the vortex core as it impinges upon the airfoil. Results for various vortex sizes and free stream velocities were obtained. Measurements were also made when the airfoil was yawed to the line vortex. Maximum pressure differences were observed to occur in phase across the blade even with yaw, and were directly proportional to the square of the free stream velocity. The maximum dynamic pressure coefficients obtained were as high as 1.0 when vortex bursting occurred.

Walsh, R. G., Jr.↗
NASA NTRS1973

Radiative lifetimes and band oscillator strengths for metal oxides. II - SiO E 1 Sigma /+/-X 1 Sigma /+/

Use of an electron-beam phase-shift apparatus to obtain the radiative lifetimes for vibrational levels of the SiO E 1 Sigma (+) state. It is found that the radiative lifetimes for the vibrational transitions of the E-X band are independent of the vibrational upper state. The measured phase shifts yield cascade free lifetimes of 10.5 plus or minus 1.1 nsec for v' from 1 to 7. Spectroscopic data from Elander and Lagerqvist (1971) were used to calculate potential curves by the Klein-Dunham procedure, and Franck-Condon factors and r-centroids for the transition were computed.

Elander, N.↗
NASA NTRS1983

A 10 deg K triple-expansion Stirling-cycle cryocooler

The design of a triple expansion closed cycle Stirling cryocooler optimized for a cooling load of 50 mW at 10 K is described. The cooler was designed with the objectives of low power, low weight, compactness, low mechanical motion, low electromagnetic noise, and low output temperature fluctuations. The design employs a direct drive linear motion piston motor and a triple expansion free displacer. Piston motion is controlled by feedback from an optical position transducer. Mechanical vibrations are attenuated with a passive resonant counterbalance. Electromagnetic noise is attenuated with layered high permeability magnetic shielding. The regenerators move with the displacer within a thin titanium cold finger. The piston and displacer oscillate at 8.33 Hz on bearings and seals of reinforced Teflon. The cooler is designed to provide the desired 50 mW of cooling at 10 K with a power input of less than 100 W. The piston can be driven at a greater stroke to produce up to 200 mW of cooling with an input power of 250 W. A lead and copper cold tip heat exchanger will limit temperature fluctuations to within 0.01 K.

Newman, W.↗
NASA NTRS1972

Flight-test results from two total temperature probes for air-data measurements up to 2014 K (3625 R)

An experimental temperature probe package containing a fluidic oscillator temperature probe and a shielded thermocouple temperature probe was tested during several X-15 flights. The X-15 flights provided greatly varying test conditions, including a wide range of rapidly changing total temperatures and Mach numbers which extended from subsonic to hypersonic speeds. Within restricted ranges of free-stream Mach number, free-stream unit weight flow, and local stagnation pressure, both probes yielded ramp outputs of temperature parallel to ramp inputs of free-stream total temperature. Within these ranges both probes were used to determine total temperature in the Mach 6 temperature environment. Because ambient temperature was known, both probes were used to estimate velocity and Mach number.

Nugent, J.↗
NASA NTRS1972

A second quantized model of anharmonicity.

A heuristic description is given for a simple harmonic oscillator as a basis for a model of anharmonicity. A formalism is applied in the process, which applies to complex excitation fields involving particle clusters and also facilitates a description of nonequilibrium multibody configurations by classical methods. The heuristic description is based on Streit's results (1965) and is free of linearization requirements in most physically interesting situations.

Rasetti, M.↗
NASA NTRS1975

Recent developments in dynamic stall

Tests were performed on an airfoil in a low-turbulence subsonic wind tunnel at fixed incidence for different speeds of the wind, the airfoil being in translatory motion normal or parallel to the wind. The resulting aerodynamic forces and moment on the airfoil were measured along with local pressure and skin friction. When the incidence is small and the boundary layer attached, no unsteady effects were observed. However, for a large incidence (16 deg), in the case of boundary layer separation, strong unsteady effects are revealed when the boundary layer is reattached in periodic flow. Reattachment can be explained assuming that for the same value of free stream velocity, the gradient of the modulus of the periodic component of the relative airspeed at the upper surface of the airfoil in a direction normal to this surface is greater than the gradient of the relative air speed at the upper surface when the airfoil is not oscillating.

Mccroskey, W. J.↗
NASA NTRS1974

Analysis of oscillatory pressure data including dynamic stall effects

The dynamic stall phenomenon was examined in detail by analyzing an existing set of unsteady pressure data obtained on an airfoil oscillating in pitch. Most of the data were for sinusoidal oscillations which penetrated the stall region in varying degrees, and here the effort was concentrated on the chordwise propagation of pressure waves associated with the dynamic stall. It was found that this phenomenon could be quantified in terms of a pressure wave velocity which is consistently much less than free-stream velocity, and which varies directly with frequency. It was also found that even when the stall region has been deeply penetrated and a substantial dynamic stall occurs during the downstroke, stall recovery near minimum incidence will occur, followed by a potential flow behavior up to stall inception.

Carta, F. O.↗
NASA NTRS1975

Chordwise propagation of dynamic stall cells on an oscillating airfoil

The dynamic stall phenomenon was examined in detail by analyzing a set of unsteady pressure data obtained on an airfoil oscillating in pitch. These data were for sinusoidal oscillations which penetrated the stall region in varying degrees, and here the effort was concentrated on the chordwise propagation of pressure waves associated with the dynamic stall. It was found that this phenomenon could be quantified in terms of a pressure wave velocity which is consistently much less than free-stream velocity, and which varies directly with frequency. It was also found that even when the stall region has been deeply penetrated and a substantial dynamic stall occurs during the downstroke, stall recovery near minimum incidence will occur, followed by a potential flow behavior up to stall inception.

Carta, F. O.↗
NASA NTRS1986

Design of a thermocapillary flow experiment in reduced gravity

Detailed considerations for the design of a low-gravity thermocapillary flow experiment are presented. The basic configuration is one in which a fluid contained in a circular dish is subjected to an imposed surface heat flux. Specific consideration is given to the imposed thermal signature, thermal boundary conditions, free-surface deformations, and g-jitter effects. Numerical analysis and ground-based and drop-tower tests are utilized to ensure that reasonable flows are obtained in which measurements can be made relatively easily. The configuration chosen is of further importance because it differs from others in which oscillations were observed.

Kamotani, Y.↗
NASA NTRS1969

Flight Test of a 40-Foot Nominal Diameter Disk-Gap-Band Parachute Deployed at a Mach Number of 3.31 and a Dynamic Pressure of 10.6 Pounds per Square Foot

A 40-foot-nominal-diameter (12.2 meter) disk-gap-band parachute was flight tested as part of the NASA supersonic high altitude parachute experiment (SHAPE) program. The test parachute (which included an experimental energy absorber in the attachment riser) was deployed from an instrumented payload by means of a deployment mortar when the payload was at a Mach number of 3.31 and a free-stream dynamic pressure of 10.6 pounds per square foot (508 newtons per square meter). The parachute deployed properly, the canopy inflating to a full-open condition at 1.03 seconds after mortar firing. The first full inflation of the canopy was immediately followed by a partial collapse with subsequent oscillations of the frontal area from about 30 to 75 percent of the full-open frontal area. After 1.07 seconds of operation, a large tear appeared in the cloth near the canopy apex. This tear was followed by two additional tears shortly thereafter. It was later determined that a section of the canopy cloth was severely weakened by the effects of aerodynamic heating. As a result of the damage to the disk area of the canopy, the parachute performance was significantly reduced; however, the parachute remained operationally intact throughout the flight test and the instrumented payload was recovered undamaged.

TESTS↗
NASA NTRS1940

DFS Dive-control Brakes for Gliders and Airplanes ; And, Analytical Study of the Drag of the DFS Dive-control Brake

These two reports are surveys on the progress and present state of development of dive-control flaps for gliders and airplanes. The second article describes how on the basis of wind tunnel and free-flight tests, the drag increase on brake flaps of the type DFS, can be predicted. Pressure records confirm a two-dimensional load distribution along the brake-flap surface Aerodynamically, the location of the brake flaps along the span is of importance for reasons of avoidance of vibration and oscillation phenomena on control and tail surfaces; statically, because of the magnitude of the frontal drag in diving with respect to the bending moments, which may become decisive for the dimensions of the wing attachment and for the wing covering.

Jacobs, Hans↗
NASA NTRS2004

Multi-d CFD Modeling of a Free-piston Stirling Convertor at NASA Glenn

A high efficiency Stirling Radioisotope Generator (SRG) is being developed for possible use in long duration space science missions. NASA s advanced technology goals for next generation Stirling convertors include increasing the Carnot efficiency and percent of Carnot efficiency. To help achieve these goals, a multidimensional Computational Fluid Dynamics (CFD) code is being developed to numerically model unsteady fluid flow and heat transfer phenomena of the oscillating working gas inside Stirling convertors. Simulations of the Stirling convertors for the SRG will help characterize the thermodynamic losses resulting from fluid flow and heat transfer between the working gas and solid walls. The current CFD simulation represents approximated 2-dimensional convertor geometry. The simulation solves the Navier Stokes equations for an ideal helium gas oscillating at low speeds. The current simulation results are discussed.

Wilson, Scott D.↗
NASA NTRS2003

Spurious States-Free Solution of the k dot p Hamiltonian for Heterostructures

A method for eliminating spurious solution in the k dot p Hamiltonian has been proposed. Introduction of additional off-diagonal alpha k(exp 2) term converts spurious solution with large real wave vector to evanescent solution with large imaginary wave vector. This modification keeps the same effective masses at Gamma point and introduces negligible deviation from original nonparabolicity. A set of unphysical fast oscillation eigenfunctions in confined states of heterostructures are removed.

Kolokolov, Konstantin I.↗
NASA NTRS1972

Theory of two coupled lasers.

A transmitting window is used to weakly couple two resonant optical cavities. When active medium is placed in one cavity, the system describes a laser coupled to a resonant cavity, while active medium in both cavities describes two coupled lasers. Equations of motion for the fields in the two cavities are found. These equations are solved in the steady state when the cavities are sufficiently closely tuned that the lasers in the two cavities oscillate with the same frequency. In the locked situation, the second cavity tends to stabilize the frequency of operation against changes in length of the first cavity. When there is no active medium in the second cavity, and that cavity becomes very long, the laser acts as if it were looking into free space.

Spencer, M. B.↗
NASA NTRS1993

Lightweight linear alternators with and without capacitive tuning

Permanent magnet excited linear alternators rated tens of kW and coupled to free-piston Stirling engines are presently viewed as promising candidates for long term generation of electric power in both space and terrestrial applications. Series capacitive cancellation of the internal inductive reactance of such alternators was considered a viable way to both increase power extraction and to suppress unstable modes of the thermodynamic oscillation. Idealized toroidal and cylindrical alternator geometries are used for a comparative study of the issues of specific mass and capacitive tuning, subject to stability criteria. The analysis shows that the stator mass of an alternator designed to be capacitively tuned is always greater than the minimum achievable stator mass of an alternator designed with no capacitors, assuming equal utilization of materials ratings and the same frequency and power to a resistive load. This conclusion is not substantially altered when the usually lesser masses of the magnets and of any capacitors are added. Within the reported stability requirements and under circumstances of normal materials ratings, this study finds no clear advantage to capacitive tuning. Comparative plots of the various constituent masses are presented versus the internal power factor taken as a design degree of freedom. The explicit formulas developed for stator core, coil, capacitor, and magnet masses and for the degree of magnet utilization provide useful estimates of scaling effects.

Niedra, Janis M.↗