Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FRACTURE MECHANICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Preliminary report on tests of tensile specimens with a part-through surface notch for a filament wound graphite/epoxy material

The behavior of tensile coupons with surface notches of various semi-elliptical shapes were evaluated for specimens obtained from a filament wound graphite/epoxy cylinder. The quasi-static test results, in some instances, are inadequate for defining complete trend curves and the interpretive analysis is considered to be preliminary. Specimens with very shallow notches were observed to be notch insensitive and the unnotched strength from these specimens was determined to be 54.97 Ksi. The failure strain of the laminate was found to be 1.328%. Specimens with deeper notches were sensitive to notch depth, notch aspect ratio, and specimen width. Using the unnotched strength of 54.97 Ksi and Poe's general toughness parameter, the fracture toughness was estimated to be 27.2 Ksi square root of In. Isotropic linear elastic fracture mechanics together with the estimated fracture toughness correctly predicted the influence of notch depth, aspect ratio, and specimen finitewidth.

Harris, C. E.↗

Elevated temperature crack growth in advanced powder metallurgy aluminum alloys

Rapidly solidified Al-Fe-V-Si powder metallurgy alloy FVS0812 is among the most promising of the elevated temperature aluminum alloys developed in recent years. The ultra fine grain size and high volume fraction of thermally stable dispersoids enable the alloy to maintain tensile properties at elevated temperatures. In contrast, this alloy displays complex and potentially deleterious damage tolerant and time dependent fracture behavior that varies with temperature. J-Integral fracture mechanics were used to determine fracture toughness (K sub IC) and crack growth resistance (tearing modulus, T) of extruded FVS0812 as a function of temperature. The alloy exhibits high fracture properties at room temperature when tested in the LT orientation, due to extensive delamination of prior ribbon particle boundaries perpendicular to the crack front. Delamination results in a loss of through thickness constraint along the crack front, raising the critical stress intensity necessary for precrack initiation. The fracture toughness and tensile ductility of this alloy decrease with increasing temperature, with minima observed at 200 C. This behavior results from minima in the intrinsic toughness of the material, due to dynamic strain aging, and in the extent of prior particle boundary delaminations. At 200 C FVS0812 fails at K levels that are insufficient to cause through thickness delamination. As temperature increases beyond the minimum, strain aging is reduced and delamination returns. For the TL orientation, K (sub IC) decreased and T increased slightly with increasing temperature from 25 to 316 C. Fracture in the TL orientation is governed by prior particle boundary toughness; increased strain localization at these boundaries may result in lower toughness with increasing temperature. Preliminary results demonstrate a complex effect of loading rate on K (sub IC) and T at 175 C, and indicate that the combined effects of time dependent deformation, environment, and strain aging may play a role. Fractography showed that microvoid coalescence was the microscopic mode of fracture in FVS0812 under all testing conditions. However, the nature of the microvoids varied with test temperature and loading rate, and is complex for the fine grain and dipersoid sizes of FVS0812.

Porr, William C., Jr.↗

Data base for crack growth properties of materials

A computerized data base of crack growth properties of materials was developed for use in fracture control analysis of rocket engine components and other NASA space hardware. The software system has files of basic crack growth rate data, other fracture mechanics material properties such as fracture toughness and environmental crack growth threshold values, and plotting and fitting routines for deriving material properties for use in fracture control analysis. An extensive amount of data was collected and entered, and work is continuing on compiling additional data. The data base and software codes are useful both for fracture control analysis and for evaluation or development of improved crack growth theories.

Forman, Royce G.↗

An Investigation on the Accuracy of Delamination Analysis Predictions for Unidirectional Laminate Configurations

The state-of-the-art methodologies for predicting delamination growth in composite laminates make use of the concept of mixed-mode fracture mechanics. In mixed-mode fracture approaches the individual Mode I, Mode II and Mode III components of the strain energy release rate (SERR) need to be determined under general loading conditions. Through the use of mixed-mode fracture, the individual components are used in combination with the critical strain energy release rates (interlaminar fracture toughnesses) for each fracture mode in a mixed mode criterion in order to predict delamination extension. These interlaminar fracture toughnesses are traditionally obtained by testing of unidirectional laminate coupons. This work presents an investigation on the accuracy of Double Cantilever Beam (DCB), End Notch Flexure (ENF) and Mixed-Mode Bending (MMB) delamination analysis predictions by comparing measured total strain-energy release rates obtained experimentally to results for structural analysis from closed-form expressions, shell finite element analysis, and continuum two-dimensional (2D) and three-dimensional (3D) (solid) finite element analysis.

Patrick Enjuto↗

A Novel Workflow for Coupled Simulation of Hydraulic Stimulation with Simultaneous Injection of Proppant

Enhanced Geothermal Systems (EGS) are located in impermeable host rock. Therefore, to achieve promising circulation, hydraulic stimulation is a key factor. Stimulation involves injecting a combination of fluids and proppant particles into existing fractures under high pressure. The effectiveness of stimulation depends on a variety of different factors, including the pressurization scheme and the optimal choice of carrying fluid and proppant particles to be used. For example, high-density particles can settle out of the injected slurry quickly, whereas lighter particles as well as a dense carrying fluid allow for a long transport into the reservoir. A numerical tool is therefore essential to take all these factors into account and to make robust predictions about the performance of the hydraulic stimulation. We present a novel computational application for coupled numerical simulation of hydraulic stimulation with concurrent injection of proppant in a fractured geothermal reservoir. This application is based on the open-source MOOSE framework that has been enriched with a set of equations to account for the circulation of proppant-laden slurries. It accounts for both the fluid and proppant components of the mixture, as well as particle-driven processes that include gravity settling, particle-particle interactions, and strong density and viscosity contrasts. A particular challenge is the mutual coupling with fracture mechanical processes in a propagating fracture using the FE code Defmod. Aperture and fluid pressure on one side and slurry density and viscosity changes on the other side interact and affect each other. Their basic understanding is therefore essential for the success of the stimulation. We compare our application to common numerical benchmark problems for both slurry flow and hydraulic stimulation.

15 GEOTHERMAL ENERGY↗

Hydro-chemo-mechanical phase field formulation for corrosion induced cracking in reinforced concrete

Steel corrosion induced cracking in reinforced concrete structures is often caused by volumetric straining at the steel-concrete interface. This volumetric strain is mainly controlled by the rate of generation of corrosion product, which depends on the diffusion of Cl{sup −} and dissolved O{sub 2} as well as the chemical reaction at the steel-concrete interface. While many numerical modeling techniques have been proposed to tackle this complex phenomenon, most have been limited to using staggered solution schemes, where the diffusion, chemical reaction, mechanical strain, and crack fields are solved for separately. Unfortunately, such approaches introduce numerical errors that can lead to unrealistic predictions. Therefore, a coupled solution, is needed to remove the formulation induced errors and understand this complex phenomenon. To provide a unifying solution framework for corrosion induced cracking in reinforced concrete, a phase field formulation is presented and implemented with FEM algorithms. The governing equations are derived from the system's free energy and Fick's law of diffusion. The proposed formulation was first validated in 1D by comparing the modeling results with the semi-analytical solution approximated via Laurent series to avoid singularities in the complex domain. 2D plane strain solutions to the embedded rebar undergoing corrosion induced cracking with pre-cracks are also presented and compared with the approximated solutions from linear elastic fracture mechanics theory (LEFM). The modeling of crack propagation enabled by the proposed formulation is also presented along with parametric studies to reveal the roles of the fracture toughness and permeability of the concrete on the corrosion induced cracking. A case study was also conducted on H-pile steel with concrete jackets to demonstrate the feasibility of modeling corrosion induced fracture in reinforced concrete structures with complex steel-concrete interfaces.

36 MATERIALS SCIENCE↗

Use of Neutron Flux Calculated by Shift in a Grizzly Reactor Pressure Vessel Fracture Simulation

The reactor pressure vessel (RPV) plays the critical role of containing the reactor and coolant in a light water reactor nuclear power plant, and must be able to safely perform this function under a variety of normal and off-normal transient loading conditions. The RPV is subjected to harsh environmental conditions (elevated temperature and high neutron flux) whenever the plant is operating, which leads to embrittlement of the steel over time. RPVs contain populations of flaws introduced during the manufacturing process, and the primary safety concern is that during a transient event, a fracture could initiate at the site of one of these flaws and lead to rupture of the RPV. RPVs are very rugged structures, and the probability of this occurring is very low, but as the RPV's steel becomes embrittled over time, its resistance to fracture decreases and this becomes more likely. Assessing the likelihood of RPV fracture during a transient event involves performing a probabilistic fracture mechanics analysis, in which random sampling procedures are used to assess the probability of fracture of a population of flaws. Grizzly offers unique capabilities for modeling the RPV using 1D, 2D, or 3D representations, taking advantage of parallel computing for this type of analysis. One of the important inputs to Grizzly is the spatial distribution of the neutron fluence, which has a large impact on the material embrittlement, and should thus be characterized as accurately as possible. The VERA core simulator developed by the CASL program takes advantage of high performance computing resources to perform high-fidelity multiphysics simulations of reactor physics, including the effects of neutron transport, fuel performance, and thermal hydraulics. Recently a capability was developed to also evaluate neutron fluxes away from the reactor core through the Shift code. This allows for a detailed 3D map of the spatial variation of the fluence in components such as the RPV to be computed, which is ideal for use with Grizzly. This report documents a procedure developed to use the fluences computed in Shift in a Grizzly simulation, which allows for improved realisim in the prediction of the effects of environmental exposure on propensity for reactor pressure vessel fracture. This capability demonstrated on RPVs with multiple types of configurations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Perspective: Mechanochemistry of biological and synthetic molecules

Coupling of mechanical forces and chemical transformations is central to the biophysics of molecular machines, polymer chemistry, fracture mechanics, tribology, and other disciplines. As a consequence, the same physical principles and theoretical models should be applicable in all of those fields; in fact, similar models have been invoked (and often repeatedly reinvented) to describe, for example, cell adhesion, dry and wet friction, propagation of cracks, and action of molecular motors. This perspective offers a unified view of these phenomena, described in terms of chemical kinetics with rates of elementary steps that are force dependent. The central question is then to describe how the rate of a chemical transformation (and its other measurable properties such as the transition path) depends on the applied force. I will describe physical models used to answer this question and compare them with experimental measurements, which employ single-molecule force spectroscopy and which become increasingly common. Multidimensionality of the underlying molecular energy landscapes and the ensuing frequent misalignment between chemical and mechanical coordinates result in a number of distinct scenarios, each showing a nontrivial force dependence of the reaction rate. I will discuss these scenarios, their commonness (or its lack), and the prospects for their experimental validation. Finally, I will discuss open issues in the field.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fracture toughness evaluations for spent nuclear fuel dry storage canister welds and spent nuclear fuel clad-pellet structures

Integrity of spent nuclear fuel (SNF) interim storage canisters is very important to the safety of the back-end nuclear fuel cycle. Stress corrosion cracking (SCC) potential of interim storage canister has been considered as a high priority. Because no post-weld heat treatment was required for forming these canisters, the high tensile residual stress existed within these canister welds. This can change the fracture resistance capacity significantly as well as increase SCC potential. Due to relative thin shell thickness of a canister weldment, the spiral notch torsion test (SNTT) method was used to estimate the canister weldment fracture toughness. SNTT was developed to measure the intrinsic fracture toughness of structural materials using small specimens. The SNTT method has been applied to a wide variety of structural materials, such as low-alloy steels, stainless steel, aluminum alloy, ceramics, concrete, and composites. The SNTT system operates by applying pure torsion to cylindrical specimens with a notch line that spirals around the specimen at a 45° pitch. In order to carry out pure torsion load mode, biaxial tension/torsion tester was developed accordingly to perform SNTT protocol. Moreover, applying fracture mechanics approach to SNF system reliability investigation is warranted due to the inherent flaws and hydride structures existed in a SNF system after nuclear reactor operation. However, none of the existing fracture toughness data deal with fuel cladding specific geometry or spent fuel material conditions, such as cladding structure with the pellet-inserts and the associated pellet clad mechanical interactions induced mixed-mode damage mechanisms. Thus, the development of an intrinsic fracture mechanics approach that is suitable for SNF materials is needed. Furthermore, due to thin wall and small dimension of clad tubing structure, the SNTT method was used to estimate the clad tubing structure fracture toughness. Fracture testing were performed on the received stainless steel canister weldment, most SNTT weld samples fracture initiation sites are at heat-affected zone (HAZ) regions. The estimated fracture toughness J Q ’ for the baseline SS304 steel is at 283 kJ/m². The estimated JQ’ for the SS304/308 weld and baseline metals are 148 kJ/m 2 and 459 kJ/m 2 , respectively. Out of cell fracture testing for spent fuel structure were carried out on the surrogate rods made of Zr-4 clad and alumina inserts, the estimated fracture toughness values for baseline Zr-4 cladding with alumina-pellet inserts are: (1) For SNTT samples with a short or medium crack length, between 5.4-mm and 8-mm, the estimate J IQ upon fracture initiation for the baseline Zr-4 cladding is at 50 kJ/m 2 with 2-sigma uncertainty of 3.26 kJ/m 2 , and the associated K IQ is at 67.46 MPa$\sqrt{m}$; and (2) For SNTT samples with a long crack length, around 13-mm, the crack initialization is deviated from that of the Mode-I tensile fracture and appears to be a mixed-mode fracture of Mode I - tensile stress and Mode III - out of plane shear stress; the estimated J MQ is at 18.9 kJ/m 2 , the associated K MQ is at 41.4 MPa$\sqrt{m}$.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanical Behaviors of Fe75Mo5P10C7.5B2.5 Bulk Metallic Glass under Torsional Loadings

Pure- and cyclic-torsional studies were conducted on a Fe{sub 75}Mo{sub 5}P{sub 10}C{sub 7.5}B{sub 2.5} (atomic percent, at.%) bulk-metallic glass at room temperature for an understanding of its damage and fracture mechanisms. Under pure-torsional loading, the metallic glass exhibited very little plastic strain before fracture. The fracture initiated along the maximum tensile-stress plane, which is about 45{sup o} to the axial direction. The shear-fracture strength ({approx}510 MPa) is much lower than the compressive-fracture strength ({approx}3280 MPa), which suggests that different deformation mechanisms be present under various loading modes. Instead of an apparent vein-type structure, the fracture morphologies revealed a crack-initiation site, a mirror region, a mist region, and a hackle region. Under cyclic-torsional loading, fatigue cracks initiated from casting defects, and propagate generally along the maximum tensile-stress plane. A slight cyclic-hardening behavior was observed in initial loading steps. The fatigue-fracture surface consists of three main regions: the fatigue crack-initiation, crack-propagation, and final-fast-fracture areas. The striations resulting from the blunting and re-sharpening of the fatigue crack tip were observed in the crack-propagation region. Based on these results, the damage and fracture mechanisms of the metallic glass induced by torsional loadings are elucidated.

36 MATERIALS SCIENCE↗

Fracture toughness evaluation for Zr-4 clad tubing structure with pellet inserts

Applying fracture mechanics approach to spent nuclear fuel (SNF) system reliability investigation is warranted due to the inherent flaws and hydride structures existed in a SNF system after nuclear reactor operation. However, none of the existing fracture toughness data deal with fuel cladding specific geometry or spent fuel material conditions, such as cladding structure with the pellet-inserts and the associated pellet clad mechanical interactions induced mixed-mode damage mechanisms. Thus, the development of an intrinsic fracture mechanics approach that is suitable for SNF materials is needed. Due to thin wall and small dimension of clad tubing structure, the spiral notch torsion test (SNTT) method of small specimen approach was used to estimate the clad tubing structure fracture toughness. The estimated fracture toughness for Zr-4 cladding with alumina-pellet inserts are presented in this report. For SNTT samples with a short or medium crack length, between 5.4-mm and 8-mm, the estimate JIQ upon fracture initiation for the baseline Zr-4 cladding is at 50 kJ/m2 with 2-sigma uncertainty of 3.26 kJ/m2, and the associated KIQ is at 67.46 MPa√m. For SNTT samples with a long crack length, around 13-mm, the crack initialization is deviated from that of the Mode-I tensile fracture and appears to be a mixed-mode fracture of Mode I – tensile stress and Mode III – out of plane shear stress; the estimated JMQ is at 18.9 kJ/m2, the associated KMQ is at 41.4 MPa√m.

36 MATERIALS SCIENCE↗

Microstructure Anisotropy Effects on Fracture and Fatigue Mechanisms in Shape Memory Alloy Martensites

The chief scientific object was to investigate the fatigue and fracture mechanisms in NiTi shape memory alloys, in the presence of stress concentrating factors such as micro-pores and notches. In particular, the interactions between structure (factors related to the geometry of the specimen, such as holes, pores and notches) and microstructure (related to properties of the material such as grains, secondary phases, twins) in influencing the inelastic deformation, leading up to fracture in NiTi was examined. Primarily, there were two major thrusts. The first thrust focused on fracture behavior in Shape Memory Alloys where the high crystal symmetry cubic phase transformed into the low symmetry phase during deformation and propagation of cracks. This thrust revealed the interplay between size of micro-pores, size of grains and grain orientations in determining the resistance to crack growth, during cyclic tensile deformation of porous-like NiTi specimens. The role of secondary phases (impurities of Ti, often formed during fabrication) were also shown to induce local inelastic deformation gradients during tensile deformation and reduce overall extent of deformation. The second thrust focused on the fatigue and fracture behavior in the low crystal symmetry martensite phase. Unlike high symmetry phases, characterization of deformation in low symmetry phases such as martensitic NiTi has been challenging, due to a hierarchical microstructure spanning from nanoscale twins to the macroscale, a highly anisotropic microstructure stemming from the low crystal symmetry and a multitude of inelastic mechanisms for deformation. Thus, advanced X-ray techniques such as 3D high-energy diffraction microscopy and x-ray micro-Laue diffraction and spectroscopy were used in conjunction with traditional techniques such as SEM and TEM to understand the inelastic deformation in the martensite phase in NiTi, in the presence of notches. This thrust revealed a stark difference in deformation mechanisms based on the nature of stress: regions near the notch experience a highly triaxial stress while those far away experience a uniaxial stress. Additionally, while regions close to the notch were shown to deform locally by amorphization/nanocrystallization, ultimately leading to fracture, regions far away from the notch deformed in a more traditional manner, with detwinning and twin reorientation the primary mechanisms of deformation. More importantly, this thrust revealed that in the presence of structural factors such as notches, the traditional picture of reorientation (coalescence) of nanoscale martensite twins into increasingly larger domains with increased loading does not hold true, even up to fracture of the specimen. These conclusions will inform the modeling and understanding of deformation behavior of specimens, where structure and microstructure coexist and interact.

36 MATERIALS SCIENCE↗

Stress analysis of cracks

Elastic stress analyses of cracked bodies represented by stress intensity factor method - fracture mechanics

STRESS ANALYSIS↗

Transition among failure modes of the bending system with a stiff film on a soft substrate

Growing interest is being attracted by stretchable and flexible electronics recently due to their attractive characteristics, commercial potentials, and engineering challenges. In comparison with the system on a macroscopic scale, different failure modes are observed in a system with a thin film bonded on an elastomeric substrate. Furthermore, the experimental observations reveal that failure modes occur in turn with the increasing of thickness ratio of the film to substrate. In this paper, theoretical analysis is performed on the failure mechanism in this system with the focus on transitions among these failure modes based on the theory of fracture mechanics. The present theoretical predictions are coincident with related experiment results and can be used to guide the related structural design.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Develop and Connect TRISO Failure Analysis and Uncertainty Quantification to Fission Product Release Calculation Capability

The U.S. Department of Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering-scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. Stress-based failure probability has been developed and analyzed to assess the integrity of tri-structural isotropic (TRISO) fuel particles during fuel life cycles. While simple, stress-based approaches to failure probability leveraging the Weibull statistical distribution entails a number of drawbacks when stress concentration occurs near crack tips, including finite element mesh size dependency. In this report, we use an interaction integral approach to the computation of stress intensity factors in functionally graded materials (FGM) for axisymmetric models. The inner pyrolytic carbon (IPyC) cracking induced silicon carbide (SiC) failure is one of the dominated failure modes in TRISO failure analysis. In this study, we consider a crack in the IPyC layer perpendicular to the SiC layer. The interface between these two TRISO layers is considered to be porous, which we simulate considering a transition of mechanical properties over the porous length. These aspects are considered in the computation of stress intensity factor (SIF) from a fracture mechanics approach and compared with the known stress-based failure probability approach.

42 ENGINEERING↗

Softening the Gap between Wöhler and Paris – New Approaches for Fatigue Analysis –

Fatigue analysis tools can vary across industries. For example, automotive engineers often use the Wöhler (S-N) approach to design for safe-life, while aerospace engineers prioritize damage tolerance and inspection intervals, relying instead on crack growth models such as Paris’ law. Although both approaches may deal with the control of cracks in similar materials, their analysis tools and material characterizations are fundamentally distinct. This divide mirrors the classic split between stress-based strength analysis and linear elastic fracture mechanics. However, modern nonlinear models that incorporate material softening, such as cohesive laws, blur this boundary and capture fracture behaviors across scales. This presentation describes the CF23 fatigue model, which uses cohesive softening to link S-N crack initiation with crack propagation rates. CF23 spans the full fatigue spectrum, from initial propagation transients to steady-state growth and threshold conditions, offering a unified framework that bridges Wöhler and Paris-based methodologies. Example applications include fatigue crack propagation transients in adhesive interfaces and skin/stiffener separation.

cohesive elements↗

Prospects for Ductility and Toughness Enhancement of Nial by Ductile Phase Reinforcement

The use of NiAl as a structural material has been hindered by the fact that this ordered intermetallic does not exhibit significant tensile ductility or toughness at room temperature. A critical review of the operative flow and fracture mechanisms in monolithic NiAl has thus established the need for ductile phase toughening in this order system. Progress in ductile phase reinforced intermetallic systems in general and specifically NiAl-based materials has been reviewed. In addition, further clarification of the primary mechanisms involved in the flow and fracture of ductile phase reinforced alloys has evolved from ongoing investigations of several model NiAl-based materials. The mechanical behavior of these model directionally-solidified alloys (Ni-30Al and Ni-30Fe-20Al) are discussed. Finally, the prospects for developing a ductile phase toughened NiAl-based alloy and the shortcomings presently inherent in these systems are analyzed.

Noebe, R. D.↗