Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Experimental and numerical investigation of the effect of H{sub 2} enrichment on laminar methane-air flame thickness

The Rayleigh scattering technique has been applied to a V-shaped methane-air flame in order to investigate the effect of H{sub 2} enrichment on the laminar flame thickness for a wide range of equivalence ratios (0.4 to 0.9) and a wide range of enrichment rates (from 10% to 40% in volume). From the Rayleigh scattering signal, the temperature is estimated using an original noniterative experimental-numerical coupled method where the variation of the cross section across the flame front is taken into account. The determination of temperature gradient is carried out using a statistical criterion and all data post-processing are validated by comparing experimental and numerical results. As expected, a decrease in flame thickness is observed when H{sub 2} is added to methane-air flames. There is very good agreement between numerical and experimental results for equivalence ratios higher than 0.55. Below this value, a great discrepancy is observed and a large scatter between various chemical mechanisms can be observed. In the validated domain of GRImech3.0, the numerical results are used to give explanation elements concerning the decrease in the flame thickness when methane is H{sub 2}-enriched. From the energy equation analysis, two different mechanisms emerge. The first takes place at high temperature and leads to an increase of the global heat release rate magnitude. It mainly involved the chain branching reaction H + O{sub 2} <-> O + OH. The second takes place at low temperature and affect the preheat zone. It involves the reaction H + O{sub 2}(+ M) <-> HO{sub 2}(+ M) and allows the methane to be oxidized at lower temperature and thus an earlier heat release. (author)

03 NATURAL GAS↗

Chemiluminescence of BO{sub 2} to map the creation of thermal NO in flames

The aim of this study is to detect and map the local conditions that generate thermal NO in flames. According to the Zeldovich mechanism, the formation of NO comes from the local conjunction of a high concentration of atomic oxygen and a temperature above a critical high level imposed by the high activation energy of the rate-limiting reaction. The green light emitted when a flame is seeded with boron salts is a chemiluminescence from the BO{sup *}{sub 2} that is chemically formed in its excited state when BO reacts with atomic oxygen. As the rate of this oxidation is also strongly increasing with temperature, the chemiluminescence of BO{sub 2} depends on the concentration of atomic oxygen and on the temperature in a way similar to the formation rate of thermal NO. This double analogy suggests the possibility of an experimental in situ simulation of the formation rate of thermal NO or at least the use of the chemiluminescence of BO{sub 2} to map the sites where thermal NO is being created. Spectroscopic experiments and comparisons with numerical simulations have been performed to test the feasibility of this technique in laminar premixed and diffusion methane/air flames. The agreement is good except in the burnt gases of fuel-rich flames. Imaging strategies with different spectral filters have been developed in the same flames to overcome the problem of interference from soot radiation in diffusion flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On the effect of carbon monoxide addition on soot formation in a laminar ethylene/air coflow diffusion flame

The effect of carbon monoxide addition on soot formation in an ethylene/air diffusion flame is investigated by experiment and detailed numerical simulation. The paper focuses on the chemical effect of carbon monoxide addition by comparing the results of carbon monoxide and nitrogen diluted flames. Both experiment and simulation show that although overall the addition of carbon monoxide monotonically reduces the formation of soot, the chemical effect promotes the formation of soot in an ethylene/air diffusion flame. The further analysis of the details of the numerical result suggests that the chemical effect of carbon monoxide addition may be caused by the modifications to the flame temperature, soot surface growth and oxidation reactions. Flame temperature increases relative to a nitrogen diluted flame, which results in a higher surface growth rate, when carbon monoxide is added. Furthermore, the addition of carbon monoxide increases the concentration of H radical owing to the intensified forward rate of the reaction CO + OH = CO{sub 2} + H and therefore increases the surface growth reaction rates. The addition of carbon monoxide also slows the oxidation rate of soot because the same reaction CO + OH = CO{sub 2} + H results in a lower concentration of OH. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Soot volume fraction in a piloted turbulent jet non-premixed flame of natural gas

Planar laser-induced incandescence (LII) has been used to measure soot volume fraction in a well-characterised, piloted, turbulent non-premixed flame known as the ''Delft Flame III''. Simulated Dutch natural gas was used as the fuel to produce a flame closely matching those in which a wide range of previous investigations, both experimental and modelling, have been performed. The LII method was calibrated using a Santoro-style burner with ethylene as the fuel. Instantaneous and time-averaged data of the axial and radial soot volume fraction distributions of the flame are presented here along with the Probability Density Functions (PDFs) and intermittency. The PDFs were found to be well-characterised by a single exponential distribution function. The distribution of soot was found to be highly intermittent, with intermittency typically exceeding 97%, which increases measurement uncertainty. The instantaneous values of volume fraction are everywhere less than the values in strained laminar flames. This is consistent with the soot being found locally in strained flame sheets that are convected and distorted by the flow. (author)

03 NATURAL GAS↗

Probe measurements and numerical model predictions of evolving size distributions in premixed flames

Particle size distributions (PSDs), measured with a dilution probe and a Differential Mobility Analyzer (DMA), and numerical predictions of these PSDs, based on a model that includes only coagulation or alternatively inception and coagulation, are compared to investigate particle growth processes and possible sampling artifacts in the post-flame region of a C/O = 0.65 premixed laminar ethylene-air flame. Inputs to the numerical model are the PSD measured early in the flame (the initial condition for the aerosol population) and the temperature profile measured along the flame's axial centerline. The measured PSDs are initially unimodal, with a modal mobility diameter of 2.2 nm, and become bimodal later in the post-flame region. The smaller mode is best predicted with a size-dependent coagulation model, which allows some fraction of the smallest particles to escape collisions without resulting in coalescence or coagulation through the size-dependent coagulation efficiency ({gamma}{sub SD}). Instead, when {gamma} = 1 and the coagulation rate is equal to the collision rate for all particles regardless of their size, the coagulation model significantly under predicts the number concentration of both modes and over predicts the size of the largest particles in the distribution compared to the measured size distributions at various heights above the burner. The coagulation ({gamma}{sub SD}) model alone is unable to reproduce well the larger particle mode (mode II). Combining persistent nucleation with size-dependent coagulation brings the predicted PSDs to within experimental error of the measurements, which seems to suggest that surface growth processes are relatively insignificant in these flames. Shifting measured PSDs a few mm closer to the burner surface, generally adopted to correct for probe perturbations, does not produce a better matching between the experimental and the numerical results. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Combustion of butanol isomers - A detailed molecular beam mass spectrometry investigation of their flame chemistry

The combustion chemistry of the four butanol isomers, 1-, 2-, iso- and tert-butanol was studied in flat, premixed, laminar low-pressure (40 mbar) flames of the respective alcohols. Fuel-rich ({phi} = 1.7) butanol-oxygen-(25%)argon flames were investigated using different molecular beam mass spectrometry (MBMS) techniques. Quantitative mole fraction profiles are reported as a function of burner distance. In total, 57 chemical compounds, including radical and isomeric species, have been unambiguously assigned and detected quantitatively in each flame using a combination of vacuum ultraviolet (VUV) photoionization (PI) and electron ionization (EI) MBMS. Synchrotron-based PI-MBMS allowed to separate isomeric combustion intermediates according to their different ionization thresholds. Complementary measurements in the same flames with a high mass-resolution EI-MBMS system provided the exact elementary composition of the involved species. Resulting mole fraction profiles from both instruments are generally in good quantitative agreement. In these flames of the four butanol isomers, temperature, measured by laser-induced fluorescence (LIF) of seeded nitric oxide, and major species profiles are strikingly similar, indicating seemingly analog global combustion behavior. However, significant variations in the intermediate species pool are observed between the fuels and discussed with respect to fuel-specific destruction pathways. As a consequence, different, fuel-specific pollutant emissions may be expected, by both their chemical nature and concentrations. The results reported here are the first of their kind from premixed isomeric butanol flames and are thought to be valuable for improving existing kinetic combustion models. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Non-premixed counterflow methane flames in DC/AC/NS electric fields

The response of counterflow diffusion flames to sub-breakdown DC and AC electric fields, as well as their superposition with ns pulse discharge waveforms, is studied in the plane-to-plane electrode geometry. Sub-breakdown DC and low-frequency AC electric fields cause the flame displacement toward the grounded electrode, in the direction of the applied field, indicating that the body force on the positive ions exceeds that on the electrons and negative ions. As the AC frequency increases, the flame response becomes less pronounced, due to the reduction of the electrohydrodynamic (EHD) body force impulse over the AC half-period. The electric field in the electrode gap is determined by ps Electric Field Induced Second Harmonic (E-FISH) generation, with absolute calibration using sub-breakdown ns pulses overlapped with the measured electric field waveform. The results show that the electric field distribution across the flame in the current saturation regime follows the Laplacian field. This indicates that the space charge density in the gap is too low to distort the applied DC or AC field, consistent with the kinetic modeling predictions. Combining a nanosecond pulse discharge with a sub-breakdown DC field generates a diffuse plasma across the entire gap. Time-resolved and spatially resolved measurements of the electric field in the discharge indicate the ionization wave propagation between the electrodes. The present results do not exhibit a detectable flame displacement enhancement by ns discharge pulses combined with a sub-breakdown field, observed previously. Kinetic modeling calculations show that the absence of this effect in the plane-to-plane geometry is due to the rapid plasma self-shielding. This indicates that alternative electrode geometries limiting the self-shielding would be more effective for the plasma / electric field enhanced flameholding and flame stabilization applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of the characteristics and stability of air-staged flames

The influence of burner aerodynamics on the characteristics of the flame has been studied by means of detailed measurements in a laboratory gas-fired furnace. The distribution of air between two concentric injections and the swirl numbers of both air streams were systematically varied. As a result, a broad range of flames were obtained. The spatial distribution of temperature and species revealed important differences in the configuration of the flame, for which plausible interpretations are proposed. Air-staged flames led to reductions in NO{sub x} emissions down to one third. The fluctuations in pressure and heat release (estimated from OH* chemiluminescence) were characterised in detail. Their standard deviations varied widely with the burner settings, reaching the highest values in some regimes close to flame extinction and also for high staging ratios. Analysis in the frequency domain revealed some characteristic peaks in the pressure spectra, some of them associated with resonant modes of the combustion chamber and the burner. Cross-correlations between the pressure and chemiluminescence signals indicated the onset of thermo-acoustic instabilities for highly air-staged flames, but not for non-staged regimes. This is attributed to the partial premixing achieved before the second combustion stage. The results confirm that the Rayleigh index is related to the magnitude of the fluctuations but, for the cases explored, the threshold associated with the onset of thermo-acoustic coupling might be different depending on the degree of premixing. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental study on thermophoretic deposition of soot particles in laminar diffusion flames along a solid wall in microgravity

Soot deposition process in diffusion flames along a solid wall has been investigated experimentally under a microgravity environment. An ethylene (C{sub 2}H{sub 4}) diffusion flame was formed around a cylindrical rod-burner with the surrounding air velocities of V{sub a} = 2.5, 5, and 10 cm/s, the oxygen concentration of 35%, and the burner wall temperature of 300 K. A laser extinction method was adopted to measure the distribution of soot volume fraction. The experiments determined the trace of maximum soot concentration together with the relative distance of the trace of flame. Results showed that the distance was about 2-5 mm. As the surrounding air velocity increased, the region of the soot particle distribution moved closer to the burner wall. The soot particles near the flame zone tended to move away from the flame zone because of the thermophoretic force and to concentrate at a certain narrow region inside the flame. Because of the simultaneous effects of convection and the thermophoresis, soot particles finally adhered to the burner wall. It has been found that there existed an optimal air velocity for the early deposition of soot on the furnace wall. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Laser-saturated fluorescence of nitric oxide and chemiluminescence measurements in premixed ethanol flames

In this study, nitric oxide laser-saturated fluorescence (LSF) measurements were acquired from premixed ethanol flames at atmospheric pressure in a burner. NO-LSF experimental profiles for fuel-rich premixed ethanol flames ({phi} = 1.34 and {phi} = 1.66) were determined through the excitation/detection scheme of the Q{sub 2}(26.5) rotational line in the A{sup 2}{sigma}{sup +} - X{sup 2}{pi} (0,0) vibronic band and {gamma}(0,1) emission band. A calibration procedure by NO doping into the flame was applied to establish the NO concentration profiles in these flames. Chemiluminescent emission measurements in the (0, 0) vibronic emission bands of the OH{sup *} (A{sup 2}{sigma}{sup +} - X{sup 2}{pi}) and CH{sup *}(A{sup 2}{delta} - X{sup 2}{pi}) radicals were also obtained with high spatial and spectral resolution for fuel-rich premixed ethanol flames to correlate them with NO concentrations. Experimental chemiluminescence profiles and the ratios of the integrated areas under emission spectra (A{sub CH*}/A{sub CH*}(max.) and A{sub CH*}/A{sub OH*}) were determined. The relationships between chemiluminescence and NO concentrations were established along the premixed ethanol flames. There was a strong connection between CH{sup *} radical chemiluminescence and NO formation and the prompt-NO was identified as the governing mechanism for NO production. The results suggest the optimum ratio of the chemiluminescence of two radicals (A{sub CH*}/A{sub OH*}) for NO diagnostic purposes. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chirped-probe-pulse femtosecond CARS thermometry in turbulent spray flames

This paper presents temperature measurements in turbulent dilute and dense spray flames using single-laser-shot chirped-probe-pulse femtosecond coherent anti-Stokes Raman spectroscopy (CPP-fs-CARS). This ultrafast technique, with a repetition rate of 5 kHz, is applied to the piloted Sydney Needle Spray Burner (SYNSBURN TM ). The burner system features air-blast atomization of liquid injected from a needle that can be translated within a co-flowing air stream. The pilot-stabilized spray flames can range between the two extremes of dense and dilute by physically translating the needle tip relative to the burner's exit plane. The CPP-fs-CARS set-up has achieved integration times of 3 picoseconds (ps) as well as spatial resolution of approximately 800 µm along beam propagation and 60 µm in the transverse dimension. Brief details of the technique, calibration, correction of interferences, and spectral fitting processes are presented along with estimates of the associated error. The measurements are compared against well-established, line Raman–Rayleigh data for temperature collected in a turbulent CH 4 /air jet diffusion flame, which is largely non-sooting. At peak gaseous flame temperatures of up to 2512 K, the relative accuracy and precision were 2.8% and ±3.4%, respectively. Measurements in turbulent spray flames are shown after applying the relevant corrections based on non-resonant background (NRB) behavior and camera saturation effects on the shape of the CARS signal spectrum. Preliminary mapping of the temperature fields demonstrates the wealth of information available in this dataset which will provide insights into the spatio-temporal structure of spray flames once relevant statistical analysis is applied.

42 ENGINEERING↗

Characterization of multi-regime reaction zones in a piloted inhomogeneous jet flame with local extinction

In this study, gradient free regime identification (GFRI) is applied to 1D Raman/Rayleigh/LIF measurements of temperature and major species from the intermediate velocity case of the Sydney piloted inhomogeneous jet flame series to better understand the structure of reaction zones and the downstream evolution of multi-regime characteristics. The GFRI approach allows local reaction zones to be detected and characterized as premixed, dominantly premixed, multi-regime, dominantly non-premixed, or non-premixed flame structures, based on flame markers (mixture fraction, chemical mode, and heat release rate) derived from the experimental data. The statistics of chemical mode zero-crossings, which mark premixed reaction zones, and the relative populations of flame structures are shown to be sensitive to the state of mixing in the near field of the flame and to the level of local extinction farther downstream. Multi-regime structures, where premixed and non-premixed reaction zones occur in close proximity and both contribute to overall heat release, account for nearly half the total population at streamwise locations within the first several jet diameters. There is a rapid transition within the near field whereby the relative population of non-premixed and dominantly non-premixed structures grows from 0.05 to nearly 0.5, and the population of premixed and dominantly premixed structures decreases correspondingly as fluid entering the reaction zone becomes progressively fuel-rich. Local extinction and re-ignition bring a resurgence in premixed-type structures, many of which occur at fuel-lean conditions. There are also modest populations of multi-regime structures, having chemical mode zero-crossings at lean conditions, which would not exist in a fully burning jet flame.

42 ENGINEERING↗

Spontaneous Raman–LIF–CO–OH measurements of species concentration in turbulent spray flames

This paper presents new measurements of species concentrations, temperature and mixture fraction in selected regions of a turbulent ethanol spray flame. The line-Raman–LIF–COsingle bondOH setup developed at the Sandia's Combustion Research Facility is utilised to probe regions of a spray flame where laser breakdown of liquid droplets is avoided and the remaining interferences can be corrected. The spray flame is stabilised on the piloted Sydney needle spray burner, where axial translation of the liquid injecting needle in the air-blast stream can transition the spray from dilute to dense. The solution to obtaining successful measurements is found to be multifaceted and includes: the appropriate selection of flame conditions; high sensitivity of the Raman detection system permitting reduced laser energies; development of a pre-processing algorithm to reject strong droplet interferences; and application of the hybrid matrix inversion method combined with wavelet denoising to account for interference corrections and noise at the very low signal levels obtained. Unique and necessary for the successful measurements reported in this paper, a pre-processing algorithm is outlined that removes data points corrupted with strong interferences from droplets. These interferences arise from a range of sources, but the most intense are due to the laser interaction with surrounding mist or liquid fragments, such that measurements near the jet centreline are corrupted and hence discarded. Reliable measurements of mixture fraction, temperature obtained from the sum of the species number densities, and species mole fractions are reported for regions in the flames sufficiently far from the centreline. The paper demonstrates the feasibility of the judicious use of Raman scattering in turbulent spray flames, the results of which will be extremely useful for validating numerical simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spatial dynamics of steady flame 2. Low-dimensional manifolds and the role of transport processes.

The study of the spatial dynamics of steady one-dimensional H{sub 2}/O{sub 2} flames is continued. Algorithms for generating low-dimensional manifolds for these systems are presented and used to find low-dimensional manifolds for the flames and the corresponding adiabatic, isobaric chemical-kinetic systems. It is demonstrated that these algorithms generate manifolds that are more accurate than the ILDM algorithm for two-dimensional manifolds of the flames. The manifolds are then employed to study the relationship between the manifolds of the flame and the manifolds of the chemical-kinetic system. It is shown that the one-dimensional manifolds of the flame match well with the composite manifolds of the chemical kinetics, but that for two-dimensional manifolds there are discrepancies between the flame manifolds and the chemical-kinetic manifolds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Interaction of Plasma Discharges with a Flame: Experimental and Numerical Study

This paper presents experimental results and numerical simulations of methane/air non-premixed flame under plasma assistance. Without plasma assistance, the flame blows off at a 28-30 m{center_dot}s{sup -1} bulk velocity (power around 3 kW). When the discharge is on, the flame can be maintained up to a bulk velocity of 53 m{center_dot}s{sup -1}(power around 6 kW), corresponding to +90% gain in power with only a few watt of plasma power. The plasma discharges present short duration current pulses (between 100 ns and 200 ns) and occur non-monotonically (delay between two pulses from 6x10{sup -5} s to 0.1 s). The probability density function of this occurrence is significantly influenced by the mass flow rate or the absence of flame, revealing the strong coupling of the plasma with hydrodynamic and combustion. For the numerical section of this work, we simulated the flame using a Computational Fluid Dynamics code based on Direct Numerical Simulation (direct solving of Navier-Stokes equations), and investigated the thermal and/or chemical effects of discharges on the flame stability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental study of vorticity-strain rate interaction in turbulent partially-premixed jet flames using tomographic particle image velocimetry

In turbulent flows, the interaction between vorticity, ω, and strain rate, s, is considered a primary mechanism for the transfer of energy from large to small scales through vortex stretching. The ω-s coupling in turbulent jet flames is investigated using tomographic particle image velocimetry (TPIV). TPIV provides a direct measurement of the three-dimensional velocity field from which ω and s are determined. The effects of combustion and mean shear on the ω-s interaction are investigated in turbulent partially premixed methane/air jet flames with high and low probabilities of localized extinction as well as in a non-reacting isothermal air jet with Reynolds number of approximately 13,000. Results show that combustion causes structures of high vorticity and strain rate to agglomerate in highly correlated, elongated layers that span the height of the probe volume. In the non-reacting jet, these structures have a more varied morphology, greater fragmentation, and are not as well correlated. The enhanced spatiotemporal correlation of vorticity and strain rate in the stable flame results in stronger ω-s interaction characterized by increased enstrophy and strain-rate production rates via vortex stretching and straining, respectively. The probability of preferential local alignment between ω and the eigenvector of the intermediate principal strain rate, s 2 , which is intrinsic to the ω-s coupling in turbulent flows, is larger in the flames and increases with the flame stability. The larger mean shear in the flame imposes a preferential orientation of ω and s 2 tangential to the shear layer. The extensive and compressive principal strain rates, s 1 and s 3 , respectively, are preferentially oriented at approximately 45° with respect to the jet axis. As a result, the production rates of strain and vorticity tend to be dominated by instances in which ω is parallel to the s 1 ¯-s 2 ¯ plane and orthogonal to s 3 ¯.

42 ENGINEERING↗

A multi-probe thermophoretic soot sampling system for high-pressure diffusion flames

Optical diagnostics and physical probing of the soot processes in high pressure combustion pose challenges that are not faced in atmospheric flames. One of the preferred methods of studying soot in atmospheric flames is in situ thermophoretic sampling followed by transmission electron microscopy imaging and analysis for soot sizing and morphology. The application of this method of sampling to high pressures has been held back by various operational and mechanical problems. In this work, we describe a rotating disk multi-probe thermophoretic soot sampling system, driven by a microstepping stepper motor, fitted into a high-pressure chamber capable of producing sooting laminar diffusion flames up to 100 atm. Innovative aspects of the sampling system design include an easy and precise control of the sampling time down to 2.6 ms, avoidance of the drawbacks of the pneumatic drivers used in conventional thermophoretic sampling systems, and the capability to collect ten consecutive samples in a single experimental run. Proof of principle experiments were performed using this system in a laminar diffusion flame of methane, and primary soot diameter distributions at various pressures up to 10 atm were determined. High-speed images of the flame during thermophoretic sampling were recorded to assess the influence of probe intrusion on the flow field of the flame.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Flame synthesis of multi-walled carbon nanotubes using CH{sub 4}-H{sub 2} fuel blends

Flame synthesis of carbon nanotubes (CNTs) has the potential to become a cost effective, energy efficient and scalable method for large-volume commercial synthesis. The in-flame concentration of key particulate inception intermediates, i.e., CH{sub 3}, C{sub 2}H{sub 2}, C{sub 3}H{sub 3}, and C{sub 5}H{sub 5} can be tailored using hydrogen fuel blends to optimize and enhance the yield of flame synthesis processes. Additionally, synthesis of CNTs using hydrogen fuel blends (coal or biomass derived gases) creates new opportunities for efficient coal utilization and by-product synergism of coal-fired power plants. This article reports an investigation on the synthesis of CNTs using H{sub 2} doped CH{sub 4} flames. For a baseline study, nanostructures formed in diffusion flames of 100% CH{sub 4} at different fuel flow rates have been analyzed. Initially the yield of nanomaterials increases with the increase in H{sub 2} doping in the fuel mixture. However, at higher H{sub 2} concentration (10%) and flow velocity (Jet Exit Reynolds number > 200), formation of nanostructures diminishes and H{sub 2}-CH{sub 4} flames produce amorphous carbon and soot particles. The maximum yield of nanostructures occurs at 95-5% CH{sub 4}-H{sub 2} fuel compositions and 8.37E-07m{sup 3}/s (corresponding Jet Exit Reynolds number=200). Raman analyses of the pristine samples show the existence of distinctive multi-walled carbon nanotube (MWNT) D and G bands at 1321cm{sup -1} and 1595cm{sup -1}, respectively. Infrared absorption measurements of vibrational line characteristics of CNTs also reveal the presence of C-H bonds.

01 COAL, LIGNITE, AND PEAT↗