Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXTRUSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Effect of Zr on microstructures and mechanical properties of an Al-Mg-Si-Cu-Cr alloy prepared by low frequency electromagnetic casting

The Al-1.6Mg-1.2Si-1.1Cu-0.15Cr (all in wt. %) alloys with and without Zr addition prepared by low frequency electromagnetic casting process were investigated by using the optical microscope, scanning electron microscope and transmission electron microscope equipped with energy dispersive analytical X-ray. The effects of Al{sub 3}Zr phases on the microstructures and mechanical properties during solidification, homogenization, hot extrusion and solid solution were studied. The results show that Al{sub 3}Zr phases reduce the grain size by ∼ 29% and promote the formation of an equiaxed grain structure during solidification. Numerous spherical Al{sub 3}Zr dispersoids with 35–60 nm in diameters precipitate during homogenization, and these fine dispersoids change little during subsequent hot extrusion and solid solution. Adding 0.15 wt. % Zr results in no recrystallization after hot extrusion and partial recrystallization after solid solution, while the recrystallized grain size is 400–550 μm in extrusion direction in the Zr-free alloy. In addition, adding 0.15 wt. % Zr can obviously promote Q′ phase precipitation, while the β″ phases are predominant in the alloy without Zr. Adding 0.15 wt. % Zr, the ultimate tensile strength of the T6 treated alloy increases by 45 MPa, while the elongation remains about 16.7%. - Highlights: • Minor Zr can refine as-cast grains of the LFEC Al-Mg-Si-Cu-Cr alloy. • L1{sub 2} Al{sub 3}Zr phases with 35–60 nm in diameter precipitate during homogenization. • L1{sub 2} and DO{sub 22} Al{sub 3}Zr phases result in partial recrystallization after solid solution. • Minor Zr can promote the precipitation of Q′ phases. • Mechanical properties of Al-Mg-Si-Cu-Cr-Zr alloy are higher than those of AA7005.

36 MATERIALS SCIENCE↗

Status update on the US ODS development program

Three papers are attached highlighting some recent progress in the development and testing of Oxide Dispersion Strengthened ferritic steels in tube and plate form. Aydogan et al. (2016) and Alam et al. (2016) papers summarize testing and characterization that has been performed on plate and tube materials. In the Alam et al. paper it was noted that after cross-rolling plate material of 14YWT, microcracks were formed. This resulted from an (001) texture in the plane normal to the plate causing cracking microcracking within that plane. Such microcracking affects low temperature tensile properties up to 200C. It was not seen in tube material produced by hydrostatic extrusion. In the Aydogan et al. (2016) paper characterization was performed on tubes produced from the ODS material, 14YWT. Tubes were formed through hydrostatic extrusion of plate material and hydrostatic extrusion of spray formed tubes. It was noted that strong texture on {001}<110> was formed in the plate material while shear deformation during hot extrusion produced a strong <111> ll ND texture component. In the Aydogan et al. (2017) paper detailed analysis was performed on the change in oxide size with ion irradiation to doses >500 dpa at 450C. The results show strong stability for the 2-4 nm oxide particles with a reduction in size ~25% after 270 dpa and an increase in density.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Report on the Production by Mechanical Alloying of New Heats of 14YWT

This report provides a summary of the new heats of 14YWT produced by mechanical alloying. Compared to the past heats of 14YWT, which were based on the nominal composition of Fe-14Cr-3W-0.4Ti-0.3Nb + 0.3Y 2 O 3 (wt. %), the three new heats of 14YWT contain a lower W level (1% vs. 3%) and various Ti levels of 0.2%, 0.3% and 0.4%. Powders with compositions of Fe-14Cr-1W-0.2Ti, Fe-14Cr-1W-0.3Ti and Fe- 14Cr-1W-0.4Ti were produced by ATI Powder Metals via Ar gas atomization. The mechanical alloying procedure consisted of ball milling the powder, canning and degassing the milled powder followed by consolidation of the powder by hot extrusion. Powder consisting of 1 kg mass containing 0.3% Y 2 O 3 powder was ball milled using the high kinetic energy ball mill for 40 h in Ar gas atmosphere. A total of 2 kg of powder from each of the three compositions of 14YWT was produced. The 3 batches of milled powder were added to 4 inch diameter cans that were fabricated from low carbon steel and sealed by electron beam welding. Each of the cans were degassed for 24 h at 300ºC under vacuum. For consolidation of the milled powder, the cans were solutionized at 850ºC for 2 h and then at 1000ºC for 2 h followed by extrusion through a rectangular shaped die to form the 14YWT billets. The 14YWT heat containing 0.4%Ti (14YW4T) was successfully extruded before a critical component on the extrusion press failed, thus preventing any further extrusions until it is repaired.

36 MATERIALS SCIENCE↗

Preliminary Study of Potential Utilization of Triassic Rift Basins for Long-Term Carbon Sequestration

Triassic rift basins of the eastern United States present a potential option for long–term carbon dioxide (CO 2 ) sequestration. Exposed and buried basins are located near large point CO 2 sources. Because of their similar origins, comparable fill successions indicate a level of reproducibility that can be conveyed between basins. The thick rock successions of the exposed Culpeper and Gettysburg basins served as proxies for understanding of the basin sequences. Their study allowed recognition of five mappable assemblages of rock types, herein termed lithofacies associations. These lithofacies associations were formed by alluvial fan, braided and meandering streams and marginal and distal lake depositional processes.Stratigraphic architecture of the lithofacies associations within exposed basins suggests a vertical succession that consists of an initial coarse-grained fluvial succession that is progressively replaced upward and basinward by finer grained lacustrine deposits. Along the faulted margins of the basins alluvial fans transitioning to fluvial delta deposits reflect lateral progradation and contemporaneous lateral components of the basin filling.To test the model devised in exposed basins, facies associations were developed for the buried Taylorsville Basin. This basin preserves over 8,000 feet of Triassic rocks that are concealed beneath more than 2,000 feet of Cretaceous and Tertiary Coastal Plain sediments. Composition and stratigraphic architecture of these rocks are similar to those observed in exposed basins. Infilling of the basin was the result of vertical aggradation and lateral progradation of coarse-grained to fine-grained facies. Based upon study of outcrops in the Culpeper and Gettysburg basins, groups of recurring lithologic facies were identified as the fundamental constructs of the basin’s sediment infilling. These groups of facies, termed lithofacies associations, represent an amalgamation of lithologic components from broadly similar depositional systems. These lithologic associations were then extrapolated into the exposed and buried portions of the Taylorsville basins. This effort determined that Triassic rift basins provide several avenues for potential study of geologic sequestration of carbon. The characteristic rift basin succession in the basins presents possible reservoir targets within the marginal fluvial deposits. Furthermore, intrusive and extrusive mafic bodies present a potential source of fracture porosity that could serve as CO 2 reservoirs. Porosity values from thin section analysis of exposed basin samples are higher in alluvial fan and braided fluvial lithofacies. Porosity is highest in samples that show less compaction, due to a lack of ductile lithic fragments and/or higher stratigraphic position. Log data from the Taylorsville Basin indicates that porosity and permeability values in basin marginal fluvial strata are elevated. Near the center of the basin, porosity and permeability values are greatly reduced, primarily owing to the fine-grained character of the lacustrine deposits. Some Triassic basins also contain thick intervals of concordant extrusive and intrusive mafic igneous rocks. These igneous bodies are potential CO 2 reservoirs for several reasons. Firstly, extrusive lava flows provide potential storage in the layers of primary porosity that occur in the vesicules formed at the top of lava flows. Secondly, both lava flows and subsurface igneous sills exhibit extensive fracture porosity produced by the rapid cooling of the flows and intrusions. Thirdly, these igneous rocks are mafic in composition, and studies have shown that iron- and magnesium-rich mafic rocks provide sequestration opportunities through carbonate remineralization. Lastly, extrusive and intrusive igneous rocks are invariably preserved within fine-grained lake deposits. These lacustrine sediments can serve as a fine-grained confining layer that encases the igneous rocks both above and below.

01 COAL, LIGNITE, AND PEAT↗

Solid Phase Processing of Lead-Free Brass with Carbon Additives

Currently, “lead-free” brass alloys (like C27450/C27451/C6930), used extensively in drinking water fixtures and automotive, electrical, and electronic applications contain maximum 0.25% lead to maintain mechanical performance and machinability. Adding graphite to brass as an alternative to lead, using casting, powder metallurgy, and extrusion methods, has been explored previously. However, all these methods have proven to be energy-, time-, and resource-intensive, while not enabling performance equivalent to that of C36000 brass. In this project, we developed a one-step approach using friction extrusion and ShAPE to make lead-free brass/graphite components such as wires, rods and tubes with mechanical performance equivalent to commercial lead-free brass alloys. Manufacturing temperatures were maintained ~550-730 °C with feed rates ranging between 4 – 25 mm/min. Results show larger grains at the center of the rods and wires with smaller grains developing at the edges. Graphite particles were sheared in the direction of extrusion with higher strains observed towards the edges. Hardness of the brass/graphite samples was over 25% higher than that of the corresponding brass-only samples (rods and wires), also friction extruded. Our results show that the sub-micron graphite plays an important role in limiting process temperature and restraining grain growth during friction extrusion, thus reducing grain size in composites.

36 MATERIALS SCIENCE↗

Processing of sintered alpha SiC

Processing methods of sintered alpha SiC for engine applications are developed in a cost effective manner, using a submicron sized powder blended with sintering aids (boron and carbon). The processes for forming a green powder compact, such as dry pressing, cold isostatic pressing and green machining, slip casting, aqueous extrusion, plastic extrusion, and injection molding, are described. Dry pressing is the simplest route to component fabrication, and is carried out at approximately 10,000 psi pressure, while in the cold isostatic method the pressure could go as high as 20,000 psi. Surfactants are added to control settling rates and casting characteristics in the slip casting. The aqueous extrusion process is accomplished by a hydraulic ram forcing the aqueous mixture through a die. The plastic forming processes of extrusion and injection molding offer the potential of greater diversity in shape capacity. The physical properties of sintered alpha SiC (hardness, Young's modulus, shear modulus, and thermal diffusivity) are extensively tested. Corrosion resistance test results of silicon carbide are included.

Storm, R. S.↗

An evaluation of the benefits of utilizing rapid solidification for development of 2XXX (Al-Cu-Mg) alloys

The advantages of rapid solidification processing over ingot metallurgy processing in the development of 2XXX aluminum alloy compositions were evaluated using a similarly processed ingot metallurgy (IM) control alloy. The powder metallurgy (PM) alloy extrusions showed a reduced age-hardening response in comparison with similar IM compositions, with higher tensile properties for naturally aged extrusions but lower properties for artificially aged ones. However, the tensile properties of naturally and artificially aged PM alloy extrusions based on a version of IM 2034 alloy, but containing 0.6 weight percent zirconium, were comparable to those of the IM control extrusions and had significantly superior combinations of strength and toughness. The tensile properties of this PM alloy showed even greater advantage in 6.4-mm (0.25-in.) and 1.8-mm (0.070-in.) plate and sheet, the yield strength being about 68 MPa (10 ksi) greater than reported values for the IM 2034 alloy sheet. An artificially aged PM alloy based on 2219 alloy also showed a strength and strength-toughness combination comparable to those of the PM Al-Cu-Mg-Zr alloy, substantially outperforming the IM 2219 alloy. These results show that rapid solidification offers the flexibility needed to modify conventional IM compositions to produce new alloy compositions with superior mechanical properties.

Paris, H. G.↗

Enhanced additive manufacturing with a reciprocating platen

An additive manufacturing extrusion head that includes a heated nozzle for accepting a feedstock and extruding the feedstock onto a substrate at a deposition plane, the nozzle having a longitudinal extrusion axis. A reciprocating platen surrounds the nozzle, the platen operable to reciprocate along the extrusion axis at or above the deposition plane as the nozzle extrudes feedstock onto the substrate; and wherein the platen flattens the extruded feedstock such that it does not protrude above the deposition plane as the extrusion head traverses over the substrate.

36 MATERIALS SCIENCE↗

Investigating microstructural evolution in SolidStir™ extruded oxide dispersion strengthened 14YWT alloy fuel cladding tube

Structural components for extreme environments require advanced materials and manufacturing processes. One such advanced material is oxide dispersion strengthened (ODS) Fe–14 wt.%Cr–3W–0.4Ti–0.3Y 2 O 3 (14YWT), which is developed for components to be used in Gen IV and fusion nuclear reactors. However, the conventional manufacturing processes to produce components, such as fuel cladding tubes, either do not retain the desired microstructural attributes or are costly and less efficient. As a result, a more attractive option is a novel manufacturing process developed on the principle of friction stir welding or processing (FSW/P) and commercially referred to as SolidStir™ Extrusion (SSE). Here this study used the SSE technique to study the manufacturing and microstructural evolution of a fuel cladding tube made of ODS 14YWT alloy. The cladding extrusion by the SSE technique involved the use of ball-milled 14YWT powders with Y, Ti, and O in the solid solution and the use of a specially designed W-25Re-Hf tool for consolidation and extrusion of the powders. A scanning electron microscope (SEM), electron backscattered diffraction (EBSD), and transmission electron microscope (TEM) were utilized for microstructural characterization. A Keyence microscope captured macrostructural photographs of the extruded tube. EBSD examination of the extruded tube on both transverse and longitudinal cross-sections showed the presence of dynamically recrystallized grains and revealed that the average grain size of the transverse cross-section was smaller than that of the longitudinal cross-section. The texture was weak and consisted of some amount of shear texture. The presence of nano-oxide clusters or precipitates of Y, Ti, and O (pyrochlores) in the extruded tube was determined by TEM. Aging heat treatment caused the average precipitate size to decrease and the density to increase compared to the as-processed condition. The results indicated that SSE is a viable tool for manufacturing fuel cladding tubes with the desired microstructural attributes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Final Technical Report for the Martin County Hydrogen Fuel Cell Development Project

In September 2008, the U.S. Department of Energy and Martin County Economic Development Corporation entered into an agreement to further the advancement of a microtubular PEM fuel cell developed by Microcell Corporation. The overall focus of this project was on research and development related to high volume manufacturing of fuel cells and cost reduction in the fuel cell manufacturing process. The extrusion process used for the microfiber fuel cells in this project is inherently a low cost, high volume, high speed manufacturing process. In order to take advantage of the capabilities that the extrusion process provides, all subsequent manufacturing processes must be enhanced to meet the extrusion line’s speed and output. Significant research and development was completed on these subsequent processes to ensure that power output and performance were not negatively impacted by the higher speeds, design changes and process improvements developed in this project. All tasks were successfully completed resulting in cost reductions, performance improvements and process enhancements in the areas of speed and quality. These results support the Department of Energy’s goal of fuel cell commercialization.

08 HYDROGEN↗

The Effects of Grain Refinement and Rare Earth Intermetallics on Mechanical Properties of As-Cast and Wrought Magnesium Alloys

The effects of rare earth intermetallics and grain refinement by alloying and hot extrusion on the mechanical properties of Mg-Gd-Al-Zn alloys have been studied to elucidate some useful ways to enhance the mechanical properties of magnesium alloys. It was revealed that aluminum as an alloying element is a much better grain refining agent compared with gadolinium, but the simultaneous presence of Al and Gd can refine the as-cast grain size more efficiently. The presence of fine and widely dispersed rare earth intermetallics was found to be favorable to achieve finer recrystallized grains during hot deformation by extrusion. The presence of coarse dendritic structure in the GZ61 alloy, grain boundary eutectic containing Mg{sub 17}Al{sub 12} phase in the AZ61 alloy, and rare earth intermetallics with unfavorable morphology in the Mg-4Gd-2Al-1Zn alloy was found to be detrimental to mechanical properties of the alloy in the as-cast condition. As a result, the microstructural refinement induced by hot extrusion process resulted in a significant enhancement in strength and ductility of the alloys. The presence of intermetallic compounds in the extruded Mg-4Gd-2Al-1Zn and Mg-2Gd-4Al-1Zn alloys deteriorated tensile properties, which was related to the fact that such intermetallic compounds act as stress risers and microvoid initiation sites.

36 MATERIALS SCIENCE↗

Alleviation of Mechanical Anisotropy in Ultrafine/Nano-grained AZ31 Magnesium Alloy

An ultrafine/nano-grained AZ31 magnesium alloy was processed through multipass accumulative back extrusion at 280 and 380 °C. Texture analysis was conducted to determine preferred crystallographic orientations developed during multipass deformation. The anisotropy in mechanical properties of the processed materials was studied by compressive and tensile testing. The results implied that the accumulative back extrusion effectively reduces the anisotropy of yield strength, ultimate strength and strain-to-fracture during compressive and tensile loading. The operations of different twinning/slip systems during compressive and tensile deformation were discussed using Schmid factors measurements. A decrease in twinning-related anisotropy, as well as the contribution of different slip systems in strain accommodation, could reduce the mechanical anisotropy of ultrafine/nano-grained AZ31 alloy. The compressive strength of the two-pass processed material was lower along extrusion direction than transverse direction; however, the result was reverse after four passes. The tensile behavior implied that the contribution of basal slip might accommodate strain along length as well as the thickness of the specimen, while prismatic slip may assist in narrowing the width of the specimen and elongating the length.

36 MATERIALS SCIENCE↗

Elucidating the Effect of TiB{sub 2} Volume Percentage on the Mechanical Properties and Corrosion Behavior of Al5083-TiB{sub 2} Composites

Al5083-TiB{sub 2} in situ composites with 1, 3, and 5 volume percentages of TiB{sub 2} were fabricated. The effect of different volume percentages of TiB{sub 2} reinforcement particles on the mechanical properties and corrosion resistance of these composites was investigated. The hot extrusion process resulted in fragmentation and more homogeneous distribution of TiB{sub 2} particles throughout the Al5083 matrix. Also, the grain size reduced as the amount of TiB{sub 2} reinforcement particles increased which caused the improvement of both the strength and ductility of the material. It was shown that the hardness, the ultimate tensile strength (UTS), and the yield strength (YS) of both the as-cast and extruded materials increased with increasing TiB{sub 2} content. Also, TiB{sub 2} addition combined with the extrusion process improved both UTS and elongation (El.%) of the extruded structures which can be attributed to the presence of TiB{sub 2} particles and obtained microstructural refinement by hot extrusion process. However, the extruded Al5083-5 vol.% TiB{sub 2} composite showed lower ductility in comparison with the extruded Al5083-1 vol.% TiB{sub 2} and Al5083-3 vol.% TiB{sub 2} composites. Moreover, it could be concluded that the corrosion resistance and also the pitting corrosion behavior of the Al5083 alloy do not significantly change in the presence of TiB{sub 2} reinforcement particles.

36 MATERIALS SCIENCE↗

Methodology to determine printability criteria of highly concentrated pastes through rheological characterization

Material extrusion is an additive manufacturing technique that enables the creation of reproducible and complex hardware by depositing a viscous, shear-thinning ink onto a substrate in a custom-pattern via extrusion through a syringe. Here, the ability of an ink to be extruded onto a substrate in many layers, and maintain the desired shape is what defines the printability. Printability is often investigated by formulating, printing, and postmortem analysis of final parts in an iterative manner. Investigations of printability through rheological characterization have often been concerned with inks that straddle the line between printable and too thin, leaving out an entire class of inks that are highly-filled pastes, where extrudability is the limiting factor. Highly-filled pastes continue to pose issues for researchers as the effect of filler morphology, size, loading, and packing fraction on the ink rheology and corresponding printability is not understood. While traditional rheological characterizations may be useful for some inks, we show that protocols utilizing steady-shear, or large-amplitude oscillatory shear are difficult and unreliable for highly-filled pastes. Through transient rheology paired with real-time images we show that each traditional protocol produces inhomogeneous deformations that violate the assumptions that underly common rheological definitions. Instead, we demonstrate metrics measured with small-amplitude oscillatory shear that are correlated to the printability of various ink formulations ranging in loading. The rheological measures that accurately predict the printability of the inks are the axial stress measured at small amplitudes, and the critical stress amplitude above which rheological characterizations become impossible. In addition, we estimate the maximum packing fraction for each filler, based on the exponent common to hard sphere models, and show that the printability of each ink can be predicted by the ratio of the packing fraction to the theoretical maximum. We show how small-amplitude oscillatory shear allows users to develop printability criteria for any ink to enhance the workflow in the development of new inks, increase the performance of material extrusion printing, and improve the stability of printed parts, with less wasted time and materials.

36 MATERIALS SCIENCE↗

Vibration induced active rheology control for 3D concrete printing

3D concrete printing, an emerging automation technology for construction, requires the concrete to be flowable during pumping and extrusion but firm immediately after layer deposition. This study investigated an active rheology control using vibration to achieve these opposing requirements. The effects of vibration frequency and acceleration on rheological parameters of concrete were studied with different levels of nanoparticles in the mix. It was found that extrusion pressure and yield stress show less sensitivity to the peak velocity of the vibration up to a certain level and then they both decrease beyond this level. Also, certain level of nanoparticles inclusion found to double the reduction in extrusion pressure and yield stress. Buildability studies using 3D printers were conducted to demonstrate the active rheology control using vibration. The mechanical properties of the printed structures were also found to have improved when vibration rheology control was used.

36 MATERIALS SCIENCE↗

Assessment of asymmetrical rheological behavior of cementitious material for 3D printing application

Among the multiplicity of construction methods based on digital concrete technologies, the most common one remains the extrusion-based process. Two opposed strategies have been developed in order to print a concrete structure using extrusion: the first one emphasizes the ease-of-pumping of material which is massively accelerated to ensure the stability of the structure, when leaving the extruder; the second one uses a firm mortar able to sustain the own weight of the structure during the printing, without requiring any accelerator. Both methods have their pros and cons and don't imply the same rheological requirements. Most of the recent literature assumes that both types of material (fluid and firm) follow the same trend of behavior and obey to the Von Mises plasticity criterion, while it has been demonstrated that firm cement-based materials can exhibit a pressure dependent behavior. Moreover, rheological study is mainly based on shear rheometry, while the extrusion-based printing process requires a description of the rheological behavior in compression to predict the global stability of the structure, and in tension to prevent cracks formation. This paper investigates the fresh behavior of cement paste and mortar under different solicitations (shear, compression, tension) for different water to cement ratios. The analysis of these results allows to describe the transition between a ductile fluid material (symmetrical in tension and compression) that obeys to a Von Mises plasticity criterion, and a brittle and firm material (asymmetrical in tension and compression) that requires a pressure dependent plasticity criterion in order to predict its strength under a given solicitation.

36 MATERIALS SCIENCE↗

The Effect of processing on the 455 C tensile and fatigue behavior of boron-modified Ti-6Al-4V

This work investigated the effect of nominal boron (B) additions of 0.1 wt.% and 1.0 wt.% on the elevated-temperature (455 C) fatigue deformation behavior of Ti-6Al-4V (wt.%) for maximum applied stresses between 250 and 550 MPa (R = 0.1, 5 Hz). The alloys were evaluated in the as-cast condition as well as the cast-and-extruded condition. Boron additions resulted in a dramatic refinement of the as-cast grain size, and larger boron additions resulted in larger titanium-boride (TiB) phase volume percents. For the as-cast alloys, the B-containing alloys exhibited longer average fatigue lives than those for Ti-6Al-4V, which was suggested to be related to their increased strength and stiffness due to the addition of the strong and stiff TiB phase. The longest average fatigue lives were exhibited by the Ti-6Al-4V-0.1B alloy, which also exhibited the greatest elongation-to-failure value. The extrusions, which were performed in the {beta}-phase field, resulted in a significantly smaller grain size, a smaller {alpha}-colony size, and finer {alpha}-lath width compared to that for the as-cast B-modified alloys. The TiB whiskers were aligned in the extrusion direction and the {alpha}-phase was also strongly textured such that the basal plane was predominately oriented perpendicular to the extrusion axis. Together these microstructural features were responsible for the significantly higher 455 C yield strength, ultimate tensile strength, and fatigue strength exhibited by the cast-and-extruded alloys compared with the as-cast alloys. In the extruded condition, B-addition did not improve the tensile or fatigue strength.

36 MATERIALS SCIENCE↗

Hot-melt extrudability of amorphous solid dispersions of flubendazole-copovidone: An exploratory study of the effect of drug loading and the balance of adjuvants on extrudability and dissolution

The FDA-approved anthelmintic flubendazole has shown potential to be repositioned to treat cancer and dry macular degeneration; however, its poor water solubility limits its use. Amorphous solid dispersions may overcome this challenge, but the balance of excipients may impact the preparation method and drug release. Here, we evaluate the influence of adjuvants and drug loading on the development of an amorphous solid dispersion of flubendazole-copovidone by hot-melt extrusion. The drug, copovidone, and adjuvants (magnesium stearate and hydroxypropyl cellulose) mixtures were statistically designed, and the process was performed in a twin-screw extruder. The study showed that flubendazole and copovidone mixtures were highly extrudable, except when drug loading was high (>40%). Furthermore, magnesium stearate positively impacted the extrusion and was more effective than hydroxypropyl cellulose. The extruded materials were evaluated by modulated differential scanning calorimetry and X-ray powder diffraction, obtaining positive amorphization and physical stability results. Pair distribution function analysis indicated the presence of drug rich domains with medium-range order structure and no evidence of polymer-drug interaction. All extrudates presented faster dissolution (HCl, pH 1.2) than pure flubendazole, and both adjuvants had a notable influence on the dissolution rate. In conclusion, hot-melt extrusion may be a viable option to obtain stable flubendazole: copovidone amorphous dispersions.

60 APPLIED LIFE SCIENCES↗