SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Progress on research in high-efficiency silicon solar cells is presented. Topics addressed include: recombination measurement techniques, doped crystals, minority carrier transport, oxygen process in solar cells, solar cell models, loss mechanics in solar cells, high-efficiency metal insulators, dendritic web cells, and surface and bulk loss reduction by low-energy hydrogen doping.
High-efficiency dendritic cells were discussed. The influence of twin planes and heat treatment on the location and effect of trace impurities was of particular interest. Proper heat treatment often increases efficiency by causing impurities to pile up at twin planes. Oxide passivation had a beneficial effect on efficiency. A very efficient antireflective (AR) coating of zinc selenide and magnesium fluoride was designed and fabricated. An aluminum back-surface reflector was also effective.
Progress on the electrical, structural, and chemical characterization of silicon sheet material is reported. In the study on high temperature deformation of dendritic web ribbon, experimental creep tests were performed in four point bending under constant load conditions, and unusual behavior was observed. Also, measurements of oxygen content in web ribbon were made. Two conclusions reached are creep behavior of web which is very different from any seen for single crystal silicon and oxygen level in web silicon which is near the saturation level at the melting point of silicon.
The solidification kinetics involved in the process of melt spinning a Ni-base superalloy have been characterized. Through a correlation of ribbon thickness to melt puddle residence time, it was found that the solidification front velocity, V, is typically about 100 mm/sec at the ribbon surface not in contact with the spinning wheel. The rate of solidification varies within the ribbon, increasing with decreasing distance, S, from the wheel-contact surface as V = 3.65/s. Ribbon microstructure and texture characteristics are discussed in light of this kinetics result. The thickness-vs-time correlation was further analyzed to yield information about thermal history during ribbon formation. These thermal results are generally consistent with those deduced from dendrite arm spacing measurements.
It is explicitly shown that, in a realistic model of diffusion-controlled dendritic solidification, Ivantsov's continuous family of steady-state needle crystals is destroyed by the addition of surface tension. The starting point is in the exact integro-differential equation for the one-sided model, in two dimensions, in a moving frame of reference. In the limit of large undercooling, where the range of the diffusion field is much smaller than the radius of curvature of the tip of the needle, this problem is reduced to a linear, inhomogeneous differential equation of infinite order. A solvability condition for this equation is derived and it is shown that solutions cease to exist for arbitrarily small but finite isotropic surface tension.
An analytic approach to the problem of predicting the widths of fingers in a Hele-Shaw cell is presented. The analysis is based on the WKB technique developed recently for dealing with the effects of surface tension in the problem of dendritic solidification. It is found that the relation between the dimensionless width lambda and the dimensionless group of parameters containing the surface tension, nu, has the form lambda - 1/2 = nu exp 2/3 in the limit of small nu.
Report describes experiments on directional solidification on MAR-M246(Hf) superalloy in low gravity. Determines effects of reduction in gravity on growth of dendrites and on resultant interdendritic segregation of various constituents, particularly of additive hafnium. Interdendritic spacings and carbide contents increase.
Study of dendritic-web growth of single-crystal silicon casts doubts on previously accepted physical concepts of process.
Chill block melt spun ribbons of Ni-Mo binary alloys containing 8.0 to 41.8 wt % Mo have been prepared under carefully controlled processing conditions. The growth velocity has been determined as a function of distance from the quench surface from the observed ribbon thickness dependence on the melt puddle residence time. Primary arm spacings measured at the midribbon thickness locations show a dependence on growth velocity and alloy composition which is expected from dendritic growth models for binary alloys directionally solidified in a positive temperature gradient.
Web Dendritic Si ribbons are deformed under a well-defined four point bending stress. Since the mechanical properties of Si are known to depend on the 0 content of the material, 0 measurements using Fourier Transform Infrared Spectroscopy were done to determine a proper control sample of non-defected single crystal Si. Four point bending revealed a unique two step bending behavior for the Web Si ribbons. An initial theory for this behavior involves the interaction of the dislocations generated by the deformation with the central twin planes of the ribbons. Measurements showed a uniformly high 0 content for the Web Si ribbons, approximately 10 to the 18th power atoms/cu.cm. The Web samples had a much broader absorption peak at 9 microns than is usually seen for well-annealed single crystal Si. This broadening is thought to be related to stress in the Web Si ribbons. Two samples containing a known amount of residual stress support this hypothesis. Also, a shoulder on the infrared absorption peak associated with interstitial 0 in Si appears in the transmission vs. wavenumber plots for some of the Web samples. This shoulder has been associated with 0-vacancy complexes or with 0 at dislocations. The O content and configuration do not seem to correlate with the growth configuration of the Web Si ribbon.
The technical progress made in the Silicon Sheet Growth Program during its 11 years was reviewed. At present, in 1986, only two of the original 9 techniques have survived to the start-up, pilot-plant stage in industry. These two techniques are the edge-defined, film-fed growth (EFG) technique that produces closed shape polygons, and the WEB dendritic technique that produces single ribbons. Both the status and future concerns of the EFG and WEB techniques were discussed.
The Flat-plate Solar Array (FSA)-sponsored Fourth Silicon Stress/Strain Workshop reviewed, coordinated, and assessed the progress in understanding and controlling stress and strain during the crystal growth of silicon ribbons. dislocation electrical activity and limits on solar cell efficiency, and on studying the effects of dopants on EFG characteristics. Work on silicon for high-efficiency solar cells, stress-strain relationships in silicon ribbon, and high temperature deformation of dendritic web ribbon was also discussed.
The Jet Propulsion Laboratory (JPL) WEB Team activities were reported for activities which were directed toward identifying and attacking areas in the growth of dendritic web ribbon, to complement the program at Westinghouse Electric Corp.
Results are reported for work in high-temperature deformatin of dendritic web ribbons, and oxygen measurement in the material.
Simultaneous diffusion of liquid precursors containing phosphorus and boron into dendritic web silicon to form solar cell structures was investigated. A simultaneous junction formation techniques was developed. It was determined that to produce high quality cells, an annealing cycle (nominal 800 C for 30 min) should follow the diffusion process to anneal quenched-in defects. Two ohm-cm n-base cells were fabricated with efficiencies greater than 15%. A cost analysis indicated that the simultansous diffusion process costs can be as low as 65% of the costs of the sequential diffusion process.
Results are presented for a current set of accelerated long-term endurance tests on crystalline silicon module of various constructions. Cell materials include single crystal, semicrystal, EFG ribbon, and dendritic web ribbon. The latest data set is for the equivalent of 20-year life and showed satisfactory performance.
Several different techniques to simultaneously diffuse the front and back junctions in dendritic web silicon were investigated. A successful simultaneous diffusion reduces the cost of the solar cell by reducing the number of processing steps, the amount of capital equipment, and the labor cost. The three techniques studied were: (1) simultaneous diffusion at standard temperatures and times using a tube type diffusion furnace or a belt furnace; (2) diffusion using excimer laser drive-in; and (3) simultaneous diffusion at high temperature and short times using a pulse of high intensity light as the heat source. The use of an excimer laser and high temperature short time diffusion experiment were both more successful than the diffusion at standard temperature and times. The three techniques are described in detail and a cost analysis of the more successful techniques is provided.
This program has been designed to evaluate the potential benefits to alloy 1480 material properties due to high thermal gradient casting, hot isostatic pressing, and alternative heat treatment. Alloy 1480 castings have been obtained from vendors representing the extremes of commercial casting thermal gradients. Quantitative characterization of the dendrite arm spacing (DAS) and pore distributions has been conducted. A hot isostatic pressing (HIP) schedule, which avoids the many pitfalls of single crystal HIP has been devised for alloy 1480. In addition, an alternate heat treatment for alloy 1480 has been devised which provides benefits in mechanical properties. The standard gradient cast test material is being evaluated in the standard heat treat condition as a baseline and in the HIP plus alternate heat treated condition. The fhigh gradient cast material is being evaluated in alternate heat treat and HIP plus alternate heat treated conditions. Evaluations focus on demonstration of the benefits due to the applied processes, especially in the area of cyclic life.