Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Multiphase Modeling in a Parallel Plate Fluidized Bed Receiver for Concentrating Solar Power

A novel high temperature particle solar receiver is developed by using a light trapping planar cavity configuration. As particles fall through the cavity, the concentrated solar radiation warms the boundaries of the receiver and in turn heats the particles. Particles flow through the system, forming a packed bed at the lower end, leaving the system from the bottom at a constant flow rate. Air is introduced to the system as the fluidizing medium to improve particle heat transfer and mixing. A laboratory scale cavity receiver is built and a near IR quartz lamp is used to provide flux to the vertical wall of the heat exchanger. The system is modeled using a continuum two-fluid method. The computational model matches the experimental system size and the particle size distribution is assumed monodisperse. A conduction model that accounts for the effects of solid concentration is implemented, and the heat flux boundary condition matches the experimental setup. Radiative heat transfer is estimated using a widely used correlation during the post-processing step to determine an overall heat transfer coefficient. The model is validated against testing data and achieves less than 30% discrepancy and a heat transfer coefficient greater than 1000 W/m2K.

CSP↗
DOE OSTI2020

Impacts of swinging door lossy compression of synchrophasor data

As the number of operational Phasor Measurement Units (PMUs) is increasing, compression is becoming crucial for efficiently transferring and storing enormous amount of synchrophasor data continuously measured from a power system. Some utilities in the U.S. have already adopted a nonlinear compression technique, called Swinging Door Algorithm (SDA), assuming compressed data meets technical and regulatory requirements without resulting in any degradation of the measurements. This paper studies impacts of this compression algorithm on field measured and simulated PMU data, and presents results from spectral analyses of raw and decompressed measurements. The results show blind application of the SDA compression alters frequency content in the measurements and introduces false harmonics and aliasing. These can lead to false conclusions being drawn from the measurements about the power system condition.

42 ENGINEERING↗
DOE OSTI2020

Transport and kinetics properties of LaF 3 in FLiNaK molten salt determined by electrochemical methods

It is found that lanthanum species can exist in the form of LaF 6 3- in FLiNaK (46.5 LiF-11.5 NaF-42 KF, mol%) molten salt in previous studies. The understanding of transport and reaction kinetics parameters of LaF 6 3- ions in FLiNaK molten salt is essential for the electrochemical separation of lanthanum from FLiNaK melt to achieve the coolant clean-up in fluoride salt cooled high-temperature reactor (FHR). Through conducting chronopotentiometry tests, the diffusion coefficients of LaF 6 3- ions in FLiNaK molten salt at the temperature range of 923 K–1023 K were determined. By conducting potentiodynamic polarization measurements at different concentrations and temperatures, the exchange current density, reaction rate constant, and charge transfer coefficient were obtained. The experiment data of potentiodynamic polarization were analyzed using a non-simplified electrode kinetics equation which incorporates both mass transfer and reaction kinetics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Anomaly Detection in Seismic Data with Deep Learning: Application for Instrument Failure Detection and Forecasting

Seismic data quality assessment (QA) is the first and one of the most important steps before conducting any further data analysis. Traditional methods involve checking various metrics, such as spike detection and power spectral density, by setting strict thresholds or comparing data against synthetic benchmarks. However, these approaches often rely on pre-existing knowledge and assumptions about data anomalies, leading to potential misclassification of unusual cases. Here, in this study, we propose a deep autoencoder model, an unsupervised learning approach that evaluates data quality without making assumptions about normal and anomalous data, which can be used to identify deviations in recorded data that may indicate nascent instrument failure. We test the model with the U.S. International Monitoring System (IMS) seismic stations and demonstrate the capability of detecting anomalies on a monthly scale. This could prompt station operators to examine potential problems early, allowing sufficient time for instrument maintenance to prevent data outages. In addition, we use a new manually selected testing dataset to compare our model performance against two supervised machine learning (ML) approaches and a standard QA package, as baseline models. When applied to the dataset containing known data anomalies, performance of the supervised and unsupervised ML approaches is similar, with an accuracy of 88.1% for our model compared to ∼90% for the supervised ML approach and 78.2% for the standard QA package. Our model outperforms the baseline models when applied to new stations, where new types of data anomalies can be station-specific and not included in the training dataset. Finally, we show model transferability by training the model with data from the Global Seismograph Network only and applying it to the IMS network data. The results suggest that our model is generalizable and can be applied to new stations with good accuracy.

Lin, Jiun-Ting [Lawrence Livermore National Labora↗
DOE OSTI2020

Transfer Learning for HVAC System Fault Detection

Faults in HVAC systems degrade thermal comfort and energy efficiency in buildings and have received significant attention from the research community, with data driven methods gaining in popularity. Yet the lack of labeled data, such as normal versus faulty operational status, has slowed the application of machine learning to HVAC systems. In addition, for any particular building, there may be an insufficient number of observed faults over a reasonable amount of time for training. To overcome these challenges, we present a transfer methodology for a novel Bayesian classifier designed to distinguish between normal operations and faulty operations. The key is to train this classifier on a building with a large amount of sensor and fault data (for example, via simulation or standard test data) then transfer the classifier to a new building using a small amount of normal operations data from the new building. We demonstrate a proof-of-concept for transferring a classifier between architecturally similar buildings in different climates and show few samples are required to maintain classification precision and recall.

transfer learning, Building HVAC, Bayesian framewo↗
DOE OSTI2025

Sparse-Data Deep Learning Strategies for Radiographic Non-Destructive Testing

Radiography is an imaging technique used in a variety of applications, such as medical diagnosis, airport security, and nondestructive testing. We present a deep learning system for extracting information from radiographic images. We perform various prediction tasks using our system, including material classification and regression on the dimensions of a given object that is being radiographed. Our system is designed to address the sparse-data issue for radiographic nondestructive testing applications. It uses a radiographic simulation tool for synthetic data augmentation, and it uses transfer learning with a pre-trained convolutional neural network model. Using this system, our preliminary results indicate that the object geometry regression task saw an improvement of 70% in the R-squared value when using a multi-regime model. In addition, we increase the performance of the object material classification tasks by utilizing data from different imaging systems. In particular, using neutron imaging improved the material classification accuracy by 20% when compared to x-ray imaging.

convolutional neural networks↗
DOE OSTI2023

A Modified Sequence-to-point HVAC Load Disaggregation Algorithm

This paper presents a modified sequence-to-point (S2P) algorithm for disaggregating the heat, ventilation, and air conditioning (HVAC) load from the total building electricity consumption. The original S2P model is convolutional neural network (CNN) based, which uses load profiles as inputs. We propose three modifications. First, the input convolution layer is changed from 1D to 2D so that normalized temperature profiles are also used inputs to the S2P model. Second, a drop-out layer is added to improve adaptability and generalizability so that the model trained in one area can be transferred to other geographical areas without labelled HVAC data. Third, a fine-tuning process is proposed for areas with a small amount of labelled HVAC data so that the pre-trained S2P model can be fine-tuned to achieve higher disaggregation accuracy (i.e., better transferability) in other areas. The model is first trained and tested using smart meter and sub-metered HVAC data collected in Austin, Texas. Then, the trained model is tested on two other areas: Boulder, Colorado and San Diego, California. Simulation results show that the proposed modified S2P algorithm outperforms the original S2P model and the support-vector machine based approach in accuracy, adaptability, and transferability.

Ye, Kai↗
DOE OSTI2021

Controlled Single-Electron Transfer via Metal–Ligand Cooperativity Drives Divergent Nickel-Electrocatalyzed Radical Pathways

Electrocatalysis enables the construction of C-C bonds under mild conditions via controlled formation of carbon-centered radicals. For sequences initiated by alkyl halide reduction, coordinatively unsaturated Ni complexes commonly serve as single-electron transfer agents, giving rise to the foundational question of whether outer- or inner-sphere electron transfer oxidative addition prevails in redox mediation. Indeed, rational design of electrochemical processes requires the discrimination of these two electron transfer pathways, as they can have outsized effects on the rate of substrate bond activation and thus impact radical generation rates and downstream product selectivities. We present results from combined synthetic, electroanalytical, and computational studies that examine the mechanistic differences of single electron transfer to alkyl halides imparted by Ni metal-ligand cooperativity. Electrogenerated reduced Ni species, stabilized by delocalized spin density onto a redox-active tpyPY2Me polypyridyl ligand, activates alkyl iodides via outer-sphere electron transfer, allowing for the selective activation of alkyl iodide substrates over halogen atom donors and the controlled generation and sequestration of electrogenerated radicals. In contrast, the Ni complex possessing a redox-innocent pentapyridine congener activates the substrates in an inner-sphere fashion owning to a purely metal-localized spin, thereby activating both substrates and halogen atom donors in an indiscriminate fashion, generating a high concentration of radicals and leading to unproductive dimerization. Overall, our data establish that controlled electron transfer via Ni-ligand cooperativity can be used to limit undesired radical recombination products and promote selective radical processes in electrochemical environments, providing a generalizable framework for designing redox mediators with distinct rate and potential requirements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Airborne hyperspectral imaging of nitrogen deficiency on crop traits and yield of maize by machine learning and radiative transfer modeling

Nitrogen is an essential nutrient that directly affects plant photosynthesis, crop yield, and biomass production for bioenergy crops, but excessive application of nitrogen fertilizers can cause environmental degradation. To achieve sustainable nitrogen fertilizer management for precision agriculture, there is an urgent need for nondestructive and high spatial resolution monitoring of crop nitrogen and its allocation to photosynthetic proteins as that changes over time. Here, we used visible to shortwave infrared (400–2400 nm) airborne hyperspectral imaging with high spatial (0.5 m) and spectral (3–5 nm) resolutions to accurately estimate critical crop traits, i.e., nitrogen, chlorophyll, and photosynthetic capacity (CO 2 -saturated photosynthesis rate, V max,27 ), at leaf and canopy scales, and to assess nitrogen deficiency on crop yield. We conducted three airborne campaigns over a maize (Zea mays L.) field during the growing season of 2019. Physically based soil-canopy Radiative Transfer Modeling (RTM) and data-driven approaches i.e. Partial-Least Squares Regression (PLSR) were used to retrieve crop traits from hyperspectral reflectance, with ground truth of leaf nitrogen, chlorophyll, V max,27 , Leaf Area Index (LAI), and harvested grain yield. To improve computational efficiency of RTMs, Random Forest (RF) was used to mimic RTM simulations to generate machine learning surrogate models RTM-RF. The results show that prior knowledge of soil background and leaf angle distribution can significantly reduce the ill-posed RTM retrieval. RTM-RF achieved a high accuracy to predict leaf chlorophyll content (R 2 = 0.73) and LAI (R 2 = 0.75). Meanwhile, PLSR exhibited better accuracy to predict leaf chlorophyll content (R 2 = 0.79), nitrogen concentration (R 2 = 0.83), nitrogen content (R 2 = 0.77), and V max,27 (R 2 = 0.69) but required measured traits for model training. We also found that canopy structure signals can enhance the use of spectral data to predict nitrogen related photosynthetic traits, as combining RTM-RF LAI and PLSR leaf traits well predicted canopy-level traits (leaf traits × LAI) including canopy chlorophyll (R 2 = 0.80), nitrogen (R 2 = 0.85) and V max,27 (R 2 = 0.82). Compared to leaf traits, we further found that canopy-level photosynthetic traits, particularly canopy V max,27 , have higher correlation with maize grain yield. This study highlights the potential for synergistic use of process-based and data-driven approaches of hyperspectral imaging to quantify crop traits that facilitate precision agricultural management to secure food and bioenergy production.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Film condensation with high heat fluxes and scaled experiments using pure steam for reactor containment cooling

Condensation tests were performed using a newly developed test facility for scaling the passive containment cooling system (PCCS) to a small modular reactor (SMR). The PCCS of the SMR plays a pivotal role in ensuring greater safety, reliability, and compactness than what is afforded by traditional reactors. Therefore, a well-designed PCCS is essential to SMRs. However, previous studies and test data were unsuitable for scaling, due to high variation in the test geometry and operating conditions. This study intends to close this research gap by using a novel designed scaled test facility consisting of vertical condensing test sections featuring 1-, 2-, and 4-inch-diameter condensing tubes with annular water cooling, and by applying superheated and saturated steam with different steam mass flow ranges of 5–25 g/s. Further, the primary test data, including axial temperatures, mass flow rates, and pressures, were used in conjunction with a standard data reduction method to estimate critical parameters such as heat fluxes, heat transfer coefficients, and condensation rates. These scaled test data would support improving empirical correlations and validating condensation models to identify scaling distortion for SMR PCCSs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

CO2 hydrate crystal thickening, morphology, and Raman spectroscopy in a microfluidic device

Gas hydrates are a solid, crystalline form of water that often form at low temperatures and high pressures. Carbon dioxide (CO2) hydrates may form during carbon dioxide capture and storage (CCS) processes. These solid compounds may form in CO2 pipelines, potentially leading to a full blockage and process shutdown for plug removal. On the other hand, formation of CO2 hydrates may be desired for CO2 capture and separation. In either case, understanding the growth behavior and nature of the hydrates is vital to managing these CCS processes. Using a high-pressure, transparent microfluidic reactor, the crystalline film thickening of CO2 hydrates was observed and measured through visual microscopy and Raman spectroscopy. The impact of subcooling, pressure, and CO2 flow rate was investigated, and only CO2 flow rate was found to have a significant impact on the overall thickness of the film. Visual observations and Raman spectroscopy measurements confirmed that two distinct hydrate layers formed during thickening, one which was more porous than the other. The capillary-like channels in the porous layer indicated a mechanism for mass transfer of water through the hydrate layer. A model was developed based on this observation, and it was fit to the thickening data in order to obtain mass transfer coefficients. Results of this study can be applied to CO2 hydrate formation in pipelines and near porous media used for CO2 capture.

Wadsworth, Lindsey [Colorado School of Mines, Gold↗
DOE OSTI2020

Pulsed Thermal Tomography Nondestructive Examination of Additively Manufactured Reactor Materials (Second Annual Progress Report)

Additive manufacturing (AM) is an emerging method for cost-efficient fabrication of nuclear reactor parts. AM of metallic structures for nuclear energy applications is currently based on laser powder bed fusion (LPBF) process, which can introduce internal material flaws, such as pores and anisotropy. Integrity of AM structures needs to be evaluated nondestructively because material flaws could lead to premature failures due to exposure to high temperature, radiation and corrosive environment in a nuclear reactor. Thermal tomography (TT) provides a capability for non-destructive evaluation of sub-surface defects in arbitrary size structures. Thermal tomography is a computational method for heat diffusion-based imaging of solids, which provides 3D visualization of data from flash thermography measurements. We investigate thermal tomography imaging and nondestructive evaluation of stainless steel and nickel super alloy metallic structures produced with laser powder bed fusion (LPBF) additive manufacturing (AM) process. Metallic structures produced with LPBF contain defects, and there are limited capabilities to evaluate these structures non-destructively. Thermal tomography reconstruction of 3D apparent spatial effusivity provides information about AM structure geometry and internal material flaws. We study performance of thermal tomography in imaging of metallic structures through COMSOL computer simulations of transient heat transfer, and through reconstruction of data obtained from experimental measurements. Reconstruction of internal defects is investigated using a stainless steel 316L specimen with flat bottom hole (FBH) indentations, and Inconel 718 plate produced with laser powder bed fusion (LPBF) method, which contains imprinted hemispherical shape low density regions containing non-sintered metallic powder. The FBH’s have the same sizes as the imprinted defects in the LPBF specimens, but offer better imaging contrast. Thermal tomography reconstructions provide visualizations of internal defects, and allow for estimation of their sizes and locations. Detection sensitivity of TT is limited by noises. We investigate separation of signal from noise in thermography images using several machine learning (ML) methods, including new spatio-temporal blind source separation (STBSS) and spatio-temporal sparse dictionary learning (STSDL) methods. Performance of the ML methods is benchmarked using thermography data obtained from imaging stainless steel 316L and Inconel 718 specimens produced LPBF method with imprinted calibrated porosity defects. The ML methods are ranked by F-score and execution runtime. Finally, we investigate TT of AM stainless steel 316L specimen with imprinted internal porosity defects using relatively low-cost, small form factor infrared (IR) camera based on uncooled micro bolometer detector. Sparse coding related K-means singular value decomposition (SVD) machine learning, image processing algorithms are developed to improve quality of TT images through removal of Additive white Gaussian noise without blurring the images. Following initial qualification of an AM component for deployment in a nuclear reactor, a compact TT can also be used for in-service nondestructive evaluation (NDE). With capability to perform in-service NDE of the AM component lifecycle, TT data can be used for development of a component digital twin.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Thermal tomography 3D imaging of additively manufactured metallic structures

Thermal tomography is a computational method for heat diffusion-based imaging of solids, which provides 3D visualization of data from flash thermography measurements. We investigate thermal tomography imaging and nondestructive evaluation of stainless steel and nickel super alloy metallic structures produced with the laser powder bed fusion (LPBF) additive manufacturing (AM) process. Metallic structures produced with LPBF contain defects, and there are limited capabilities to evaluate these structures non-destructively. Thermal tomography reconstruction of 3D apparent spatial effusivity provides information about AM structure geometry and internal material flaws. We study performance of thermal tomography in imaging of metallic structures through COMSOL computer simulations of transient heat transfer and through reconstruction of data obtained from experimental measurements. Thermal tomography reconstructions of structure shape and dimensions are shown for the Inconel 718 AM structure which has variations in the horizontal plane but is uniform along the depth dimension. Reconstruction of internal defects is investigated using a stainless steel 316L specimen with flat bottom hole (FBH) indentations, and the Inconel 718 plate is produced with the LPBF method, which contains imprinted hemispherical shape low density regions containing non-sintered metallic powder. The FBHs have the same sizes as the imprinted defects in the LPBF specimens but offer better imaging contrast. Thermal tomography reconstructions provide visualizations of internal defects and allow for estimation of their sizes and locations. Results of this study demonstrate that thermal tomography can be used for visualization and quality control in AM.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Direct Evidence for Buffer-Enhanced Proton-Coupled Electron Transfer Generation of a High-Valent Metal-Oxo Complex

Here, the oxidation of metal-aquo and -hydroxo complexes to generate the high-valent metal-oxo species used in oxidative catalysis is often kinetically slow due to sluggish proton transfer between ligated −H 2 O/–OH in the proton-coupled electron transfer (PCET) chemistry. In this research, a ruthenium water oxidation catalyst anchored to a conductive tin-doped indium oxide (ITO) thin film, abbreviated ITO|Ru II –OH 2 , was characterized by spectroscopic and electrochemical methods in acetate or phosphate buffers. The deprotonated intermediate, Ru II –OH, was observed spectroscopically in the PCET half-reaction ITO(e – )|Ru III –OH + H + → ITO|Ru II –OH 2 indicating an underlying stepwise ET-PT mechanism. In contrast, at elevated buffer concentrations, this intermediate was absent, and a 2–4 order of magnitude increase in the proton transfer rate constant was observed. Kinetic data for this PCET reaction measured as a function of the driving force provided the reorganization energy λ = 1.05 eV and was assigned to a concerted electron–proton transfer (EPT) mechanism. In addition, the standard heterogeneous rate constants for two PCET equilibria, Ru III –OH + H + + e – ⇌ Ru II –OH 2 and Ru IV = O + H + + e – ⇌ Ru III –OH were enhanced by these same buffers. Collectively, the data show that the added buffers can enhance the kinetics and thermodynamics for PCET reactions relevant to oxidative catalysis.

Catalysts↗
DOE OSTI2022

Perceived Costs and Benefits of ICON Science and Foundational Documents associated with “Integrated, Coordinated, Open, and Networked (ICON) Science to Advance the Geosciences: Introduction and Synthesis of a Special Collection of Commentary Articles"

This data package is associated with the publication "Integrated, Coordinated, Open, and Networked (ICON) Science to Advance the Geosciences: Introduction and Synthesis of a Special Collection of Commentary Articles" in Earth and Space Science (Goldman et al. 2022; https://doi.org/10.1029/2021EA002099). The manuscript is an introductory article for a special collection of commentary articles across 19 geoscience disciplines that explore the challenges and opportunities associated with the use of ICON science principles. These principles focus on research intentionally designed to be Integrated, Coordinated, Open, and Networked (ICON) with the goal of maximizing mutual benefit (among stakeholders) and cross-system transferability of science outcomes. This data package contains data, figures, and R scripts associated with the cost/benefit analysis presented in the manuscript. The writing teams involved in the special collection placed each letter of ICON on a plot with perceived cost on one axis and perceived benefit on the other to summarize their perceptions of pursuing each principle of ICON science. These data were subsequently quantified and analyzed. Files are saved as .csv, .R, and .pdf. This data package also contains (1) the public foundational and instructional documents that enabled the crowdsourced creation of the special collection; (2) file-level metadata (flmd) that lists each file in the data package with a description; (3) data dictionary (dd) that defines column headers that appear in csv files. Files are saved as .pdf and .csv.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Predicting Kyasanur forest disease in resource-limited settings using event-based surveillance and transfer learning

In recent years, the reports of Kyasanur forest disease (KFD) breaking endemic barriers by spreading to new regions and crossing state boundaries is alarming. Effective disease surveillance and reporting systems are lacking for this emerging zoonosis, hence hindering control and prevention efforts. We compared time-series models using weather data with and without Event-Based Surveillance (EBS) information, i.e., news media reports and internet search trends, to predict monthly KFD cases in humans. We fitted Extreme Gradient Boosting (XGB) and Long Short-Term Memory models at the national and regional levels. We utilized the rich epidemiological data from endemic regions by applying Transfer Learning (TL) techniques to predict KFD cases in new outbreak regions where disease surveillance information was scarce. Overall, the inclusion of EBS data, in addition to the weather data, substantially increased the prediction performance across all models. The XGB method produced the best predictions at the national and regional levels. The TL techniques outperformed baseline models in predicting KFD in new outbreak regions. Novel sources of data and advanced machine-learning approaches, e.g., EBS and TL, show great potential towards increasing disease prediction capabilities in data-scarce scenarios and/or resource-limited settings, for better-informed decisions in the face of emerging zoonotic threats.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

An Intermediate Level Trigger Supernova Pointing Trigger for DUNE Using In-Storage AI

We propose a near-data approach to reduce the buffered supernova data on the DUNE DAQ front-end computers using ML techniques. Based on simulations, we are able to reduce the data by 5 orders of magnitude to 0(100)MB which can then be transferred quickly over ethernet to a single server that executes a full reconstruction and pointing analysis to determine the SN direction. The entire process of reducing the data and executing reconstruction and pointing analysis pipeline takes less time than that required to transfer all the data back to Fermilab before performing more processing to determine the direction of the supernova, which was the baseline plan for DUNE.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Multi-objective surrogate-assisted calibration of CPFEM models using macroscopic response and in situ EBSD measurements of grain reorientation trajectories

Crystal plasticity finite element method (CPFEM) models are widely used to simulate the deformation behaviour of polycrystalline materials, but their calibration is often limited by their high computational cost and the non-convexity of the optimisation landscape. Here, this study develops a multi-objective surrogate-assisted calibration workflow that couples a multi-objective genetic algorithm (MOGA) with an adaptively trained deep neural network (DNN) surrogate model to efficiently identify CPFEM parameters from experimental data. The workflow is demonstrated on three crystal plasticity (CP) formulations of increasing complexity — Voce hardening (VH), two-coefficient latent hardening (LH2), and six-coefficient latent hardening (LH6) — using in situ electron backscatter diffraction (EBSD) measurements of Alloy 617 under uniaxial tensile loading. The CPFEM models are calibrated against the experimentally observed stress–strain response and reorientation trajectories of eight grains, then validated against eight additional trajectories and overall texture evolution. Across the CP formulations, the macroscopic response was reproduced reliably, while differences emerged in the robustness and accuracy of the grain-scale predictions. Including grain reorientation trajectories in the multi-objective calibration improved texture evolution predictions and filtered out physically inconsistent parameter sets that can arise from calibrating against only the stress–strain data. The workflow also demonstrates good transferability of calibrated parameters from a low- to a high-fidelity microstructural model. These results provide practical guidance for integrating in situ microstructural data into CPFEM through efficient, repeatable, and physically meaningful multi-objective calibration.

Crystal plasticity finite element method↗