Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Performance and Reliability of Bonded Interfaces for High-Temperature Packaging. Annual Report

Current generation automotive power electronics packages utilize silicon devices and lead-free solder alloys. To meet stringent technical targets for 2020 and beyond (for cost, power density, specific power, efficiency and reliability), wide-bandgap devices are being considered since they offer advantages such as operation at higher frequencies, voltages, and temperatures. Traditional power electronics packages must be redesigned to utilize the full potential of wide-bandgap devices, and the die- and substrate-attach layers are key areas where new material development and validation is required. Present solder alloys do not meet the performance requirements for these new package designs while also meeting cost and hazardous substance restrictions. Sintered silver (Ag) promises to meet the needs for die- and substrate-attach interfaces but synthesis optimization and reliability evaluation must be completed. Sintered Ag material was proposed as an alternative solution in power electronics packages almost 20 years back. However, synthesis pressure requirements up 40 MPa caused a higher complexity in the production process and more stringent flatness specifications for the substrates. Recently, several manufacturers have developed sintered Ag materials that require lower (3-5 MPa) or even no bonding pressures. Degradation mechanisms for these sintered Ag materials are not well known and need to be addressed. We are addressing these aspects to some extent in this project. We are developing generalized (i.e., independent of geometry) stress intensity factor versus cycles-to-failure relations for sintered Ag. Because sintered Ag is a relatively new material for automotive power electronics, the industry currently does not have a good understanding of recommended synthesis parameters or expected reliability under prescribed conditions. It is an important deliverable of this project to transfer findings to industry to eliminate barriers to using sintered Ag as a viable and commercialized die- and substrate-attach material. Only a few manufacturers produce sintered Ag pastes and may consider some processing conditions as proprietary. It is the goal of this project to openly explore and define best practices in order to impact the maximum number of power electronics module manufacturers and suppliers.

30 DIRECT ENERGY CONVERSION↗

Measurement of $W$ -Boson Helicity-Fractions in Top-Quark Decays with the CDF II Experiment and Prospects for an Early $t\overline{t}$ Cross-Section Measurement with the CMS Experiment

Aus was besteht die Welt? Die Frage nach den fundamentalen Bausteinen der Materie beschaftigte Wissenschaftler und Gelehrte zu allen Zeiten. Ausgehend von abstrakten philosophischen Uberlegungen wurde das Konzept von kleinsten, nicht weiter zerteilbaren Grundbausteinen der Materie bereits einige Jahrhunderte vor Christus von indischen und griechischen Philosophieschulen entwickelt. Etwa 450 v. Chr. pragte Demokrit den Begriff ´atomos, das “Unzerschneidbare”, fur die diskreten Grundbausteine der Materie. Doch erst in der jungeren Vergangenheit konnte dieses philosophische Konzept auch experimentell uberpruft werden.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Additively Manufactured, Net Shape Powder Metallurgy Cans for Valves Used in Energy Production

Additive manufacturing (AM) has the potential to enable a paradigm shift in fabricating complex net shape components with yields over 90%, significantly increasing productivity, decreasing energy consumption during manufacturing and improving downstream energy efficiency. ORNL has developed a technology for producing large-scale additively manufactured polymer matrix composite components at deposition rates on the order of 100 lbs. per hour. This project utilized tools, dies and molds made from this technology to enable the net shape forming of cans for the powder metallurgy (PM) manufacturing of valves used in energy production plants. This approach has the potential to develop affordable valves with superior performance to castings. It will also lead to increased strength values, decreased wall thickness size, and the potential for higher yields (less machining). This project is critical for evaluating new methodologies for the fabrication of additively manufactured tooling, molds and dies that could be used across multiple industries. In the first phase of this project, a new methodology of creating a Powder Metallurgy and Hot Isostatic Pressing (PM-HIP) container by hydroforming sheet metal over additively manufactured (AM) dies was evaluated. The goal in this stage of development was to evaluate some of the new polymer matrix composite materials designed for deposition on large scale additive manufacturing systems as candidates for hydroforming steel and aluminum sheet to make thin gauge net shape components. In order to meet this objective, most research was performed on subscale tools in order to evaluate the processing pressures, material options, and gauge thicknesses most relevant to this approach. In addition, full scale AM tools (30% over final component geometry) were produced to demonstrate scalability, but were not used in testing. The first phase of this project has proven this concept has merit, but future studies are required to address minor tool failures that occurred in phase one due to geometry, cost of the process over other techniques, and demonstration of a full-scale tool that could then be used in (HIP). Lastly, this project provides the PM community a new approach in using hydroforming for the manufacturing of cans, a process that was not highly utilized for this purpose previously.

42 ENGINEERING↗

Highly Integrated Wide Bandgap Power Module for Next Generation Plug-In Vehicles (Final Report)

Wide bandgap devices are key enablers for high power density traction inverters. A highly integrated wide bandgap (WBG) power module enables higher temperature operation, higher inverter efficiency and overall smaller die area with the same power delivery. However, it requires careful design of the power module to take advantage of all the superior material properties that silicon carbide (SiC) provides over conventional silicon (Si) Insulated Gate Bipolar Transistor (IGBT) based design. This project developed an efficient and densely packed SiC power module for an automotive traction inverter application. Extensive study was performed to select the best performing SiC die considering a wide range of temperature variation, suitability to integrate into target packaging, robust body diode performance and overall high electrical efficiency. Multiple design ideas were explored to achieve lower stray inductance for both power loop and signal loop, uniform current distribution, compact form factor, and very high thermal performance. The final power module package includes all six inverter switches in the same module (six-pack) with die sintered at both bottom and top surfaces utilizing high performance substrate to achieve high electrical and thermal performance. Two power module variants were developed using 900 V and 1200 V devices for operating at two different high voltage levels (> 600 V HV battery). Both power modules were comprehensively characterized, and high efficiency operation of the inverter was confirmed through analysis. Finally, a complete functional inverter was built with the 1200V power modules using other essential components (HV capacitors, gate driver board, controller board, current sensor, connectors etc.) and tested using GM’s standard test procedure. There are several challenges associated with adopting WBG devices for high voltage operation. In order to assess and mitigate those challenges, GM and subrecipients of this project have conducted multiple detailed studies. This includes phase current reconstruction using integrated Rogowski coil, device junction temperature estimation using on-state gate resistance, modeling and testing the effect of high voltage and fast switching on motor insulation and bearings, partial discharge inception voltage measurement under different environmental conditions. Findings of all these studies are summarized in this report.

33 ADVANCED PROPULSION SYSTEMS↗

Impact of Changes in ENDF/B-VII.1 and ENDF/B-VIII.0 235U Nuclear Data Indicated by NDSE Studies on LLNL Pulsed Sphere Simulations

A recent journal article by J.A. Gomez et al. measured gamma-ray die-off curves of three subcritical static highly-enriched uranium (HEU) assemblies driven by an external neutron source with a new detector system. This new detector system was developed for being used in dynamically driven subcritical assemblies as part of the Neutron Diagnosed Subcritical Experiments (NDSE) program. Simulations of these die-off curves with various nuclear data and comparison to experimental data indicated that a decrease of the ENDF/B-VII.1 235 U(n,inl) cross section by a factor 0.8 and 0.85 for ENDF/B-VIII.0 would lead to better predictions of experimental data. Here, we test the proposed changes with another type of measurement response, namely neutron-leakage spectra emitted in LLNL pulsed sphere measurements. These spheres were pulsed by 14-MeV neutrons produced via the D+T reaction in their center. The proposed changes in nuclear data have a distinctly smaller impact on predicting pulsed-sphere neutron-leakage spectra than for the die-off curves; they lead to a worsened prediction of the inelastic valley of LLNL pulsed-sphere neutron spectra indicating that the proposed change could constitute a compensating error. Changes in the inelastic angular distributions along with the cross section might be worthwhile to study

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Solid Phase Processing at the Extreme

The effective application of high-flow-stress materials in the realm of Solid Phase Processing frequently necessitates operating at elevated temperatures and substantially high force. These rigorous processing conditions give rise to intricate predicaments concerning the durability of the tools and dies involved, as well as the efficient utilization of process energy. This project is centered on the investigation of the fundamental scientific aspects inherent to these challenges. We aim to delve into the details of how materials react when subjected to intense shear forces at die interfaces, determine the metallurgical interactions occurring at the interfaces with the dies, and investigate the consequences of extreme temperatures on material flow, microstructural evolution, and resultant properties.

36 MATERIALS SCIENCE↗

Pelleting of Pine and Switchgrass Blends: Effect of Process Variables and Blend Ratio on the Pellet Quality and Energy Consumption

The blending of woody and herbaceous biomass can influence pellet quality and the energy consumption of the process. This work aims to understand the pelleting characteristics of 2-inch top-pine residue blended with switchgrass at high moisture content. The process variables tested are blend moisture content, length-to-diameter (L/D) ratio in the pellet die, and the blend ratio. A flat die pellet mill was also used in this study. The pine and switchgrass blend ratios that were tested include: (1) 25% 2-inch top pine residue with 75% switchgrass; (2) 50% 2-inch top pine residue with 50% switchgrass; and (3) 75% 2-inch top pine residue with 25% switchgrass. The pelleting process conditions tested included the L/D ratio in the pellet die (i.e., 1.5 to 2.6) and the blend moisture content (20 to 30%, w.b.). Analysis of experimental data indicated that blending 25% switchgrass with 75% 2-inch top pine residue and 50% switchgrass with 50% 2-inch top pine residue resulted in pellets with a bulk density of > 550 kg/m3 and durability of > 95%. Optimization of the response surface models developed for process conditions in terms of product properties indicated that a higher L/D ratio of 2.6 and a lower blend-moisture content of 20% (w.b.) maximized bulk density and durability. Higher pine in the blends improved the pellet durability and reduced energy consumption.

09 BIOMASS FUELS↗

Spark Plasma Sintering of Commercial Zirconium Carbide Powders: Densification Behavior and Mechanical Properties

Commercial zirconium carbide (ZrC) powder is consolidated by Spark Plasma Sintering (SPS). Processing temperatures range from 1650 to 2100 °C. Specimens with various density levels are obtained when performing single-die SPS at different temperatures. Besides the single-die tooling setup, a double-die tooling setup is employed to largely increase the actual applied pressure to achieve higher densification in a shorter processing time. In order to describe the densification mechanism of ZrC powder under SPS conditions, a power-law creep constitutive equation is utilized, whose coefficients are determined by the inverse regression of the obtained experimental data. The densification of the selected ZrC powder is shown to be likely associated with grain boundary sliding and dislocation glide controlled creep. Transverse rupture strength and microhardness of sintered specimens are measured to be up to 380 MPa and 24 GPa, respectively. Mechanical properties are correlated with specimens’ average grain size and relative density to elucidate the co-factor dependencies.

36 MATERIALS SCIENCE↗

Thick silicon growth techniques

Hall mobility measurements on a number of single crystal silicon ribbons grown from graphite dies have shown some ribbons to have mobilities consistent with their resistivities. The behavior of other ribbons appears to be explained by the introduction of impurities of the opposite sign. Growth of a small single crystal silicon ribbon has been achieved from a beryllia dia. Residual internal stresses of the order of 7 to 18,000 psi have been determined to exist in some silicon ribbon, particularly those grown at rates in excess of 1 in./min. Growth experiments have continued toward definition of a configuration and parameters to provide a reasonable yield of single crystal ribbons. High vacuum outgassing of graphite dies and evacuation and backfilling of growth chambers have provided significant improvements in surface quality of ribbons grown from graphite dies.

Bates, H. E.↗

Thick film silicon growth techniques

One inch wide silicon ribbons up to 14 inches long have been produced from graphite dies. Several different techniques have been employed to improve the semiconductor purity of silicon. This has resulted in a general increase in quality although the techniques involved have not been optimized. The power factor of uncoated ribbon solar cells produced for material evaluation has increased to approximately 75% of those evaluation cells made from commercial silicon. The present limitation is believed due to low lifetime. Additional work has continued with new die materials; however, only composite dies of SiO2 and C show significant potential at this time.

Bates, H. E.↗

Transistor screening evaluation SJ6708H

A manufacturer was contracted to screen 125 transistors capable of withstanding the high level inductive voltages obtained when switching inductive loads. Planned differences included a change in die bonding to comply with NASA's desire for hard solder die attachment which further necessitated a change in package to conform to the required die mounting system. Evaluation of the electrical performance and recommended changes were made during the preliminary build phase of the program. The following sections are outlined: (1) narrative outline; (2) customer data summary and X-ray reports; (3) device specification; (4) failure analysis reports; (5) test facilities list; and (6) test measurement data.

Barton, J. L.↗

Selective Etching of Semiconductor Glassivation

Selective etching technique removes portions of glassivation on a semi-conductor die for failure analysis or repairs. A periodontal needle attached to a plastic syringe is moved by a microprobe. Syringe is filled with a glass etch. A drop of hexane and vacuum pump oil is placed on microcircuit die and hexane is allowed to evaporate leaving a thin film of oil. Microprobe brings needle into contact with area of die to be etched.

Casper, N.↗

Wrinkle-Free Hydroforming of Wire Mesh

Plastic films lubricate workpiece so it deforms smoothly. Thin layers of plastic below top die and above bottom die ensure wire screen slides as shaped by hydroforming. Plastic layers are 0.0043 in. (0.11 m) thick. Preformed to contours of dies and final workpiece. New method of hydroforming fine-wire-mesh heat-shield screens eliminates wrinkles and marks. Prevents screen from being damaged and pores from becoming blocked.

Fadness, J.↗

Ultrasonic angle beam standard reflector

A method that provides an impression profile in a reference standard material utilized in inspecting critically stressed components with pulsed ultrasound is described. A die stamp having an I letter is used to impress the surface of a reference material. The die stamp is placed against the surface and struck with an inertia imparting member to impress the I in the reference standard material. Upset may appear on the surface as a result of the impression and is removed to form a smooth surface. The stamping and upset removal is repeated until the entire surface area of a depth control platform on the die stamp uniformly contacts the material surface. The I impression profile in the reference standard material is utilized for reflecting pulsed ultrasonic beams for inspection purposes.

Berry, R. F., Jr.↗

A thermal-capillary mechanism for a growth rate limit in edge-defined film-fed growth of silicon sheets

Capillarity, acting to set the shape of the melt/gas interfaces, and heat transfer can interact to cause limits to steady-state growth of thin silicon sheets by the Edge-Defined Film-Fed Growth (EFG) method. A finite-element/Newton solution method for a two-dimensional thermal-capillary model of EFG is used to show that limiting values of pull rate exist beyond which steady-state growth is impossible. The pull rate limit is also predicted by a one-dimensional heat transfer model valid when the die sides and menisci are almost parallel and when the thermal conductivities of melt, crystal, and die are all equal. Both the one- and two-dimensional heat transfer models show that heat loss from the melt is dominated by conduction into the crystal and slow heat release to the ambient along the length of the ribbon. The limiting pull rate results from the reduced efficiency of conduction through the melt caused by the curvature of the meniscus which increases height of the die top above the level of the melt. Thermal-capillary limits are predicted for both positive and negative pressure differences across the meniscus.

Thomas, P. D.↗

Effect of treatment with interferon-gamma and concanavalin A on the course of infection of mice with Salmonella typhimurium strain LT-2

The effect of pretreatment of mice with 34 units/day, for five days, of interferon-gamma (IFN-gamma) on the course of infection with LD50 of Salmonella typhimurium strain LT-2 was assessed, using two IFN preparations: (1) a hybridoma supernatant fluid containing concanavalin-A-induced IFN-gamma activity and (2) pure murine IFN-gamma produced by recombinant DNA technology. The hybridoma supernatant-treated Salmonella-infected mice were found to die faster than mice treated only with Salmonella. Pure murine IFN-gamma was found to protect infected mice significantly, with 95 percent of mice surviving LD50 infection. In contrast, the Salmonella-infected mice treated with hybridoma supernatant were found to die faster than the Salmonella-infected untreated controls. Mice treated with concanavalin A alone prior to infection with S. typhimurium died more quickly than the untreated infected controls, suggesting that contamination with concanavalin A had a detrimental effect on mice survival.

Gould, Cheryl L.↗

Continuous fiber thermoplastic prepreg

A pultrusion machine employing a corrugated impregnator vessel to immerse multiple, continuous strand, fiber tow in an impregnating material, and an adjustable metered exit orifice for the impregnator vessel to control the quantity of impregnating material retained by the impregnated fibers, is provided. An adjustable height insert retains transverse rod elements within each depression of the corrugated vessel to maintain the individual fiber tows spread and in contact with the vessel bottom. A series of elongated heating dies, transversely disposed on the pultrusion machine and having flat heating surfaces with radiused edges, ensure adequate temperature exposed dwell time and exert adequate pressure on the impregnated fiber tows, to provide the desired thickness and fiber/resin ratio in the prepreg formed. The prepreg passing through the pulling mechanism is wound on a suitable take-up spool for subsequent use. A formula is derived for determining the cross sectional area opening of the metering device. A modification in the heating die system employs a heated nip roller in lieu of one of the pressure applying flat dies.

Wilson, Maywood L.↗

Corticosterone, but not Glucose, Treatment Enables Fasted Adrenalectomized Rats to Survive Moderate Hemorrhage

Fed adrenalectomized rats survive the stress of hemorrhage and hypovolemia, whereas fasted adrenalectomized rats become hypotensive and hypoglycemic after the first 90 min and die within 4 hours (h). We have studied the effects of glucose and corticosterone (B) infusions after hemorrhage as well as treatment with B at the time of adrenalectomy on the capacity of chronically prepared, conscious, fasted, adrenalectomized rats to survive hemorrhage. We have also measured the magnitudes of vasoactive hormone responses to hemorrhage. Maintenance of plasma glucose concentrations did not sustain life; however, treatment of rats at the time of adrenalectomy with B allowed 100 percent survival, and acute treatment of adrenalectomized rats at the time of hemorrhage allowed about 50 percent survival during the 5-h posthemorrhage observation period. Rats in the acute B infusion group that died exhibited significantly increased plasma B and significantly decreased plasma glucose concentrations by 2 h compared to the rats that lived. Plasma vasopressin, renin, and norepinephrine responses to hemorrhage were markedly augmented in the adrenalectomized rats not treated with B, and plasma vasopressin concentrations were significantly elevated at 1 and 2 h in all of the rats that subsequently died compared to values in those that lived. We conclude that: 1) death after hemorrhage in fasted adrenalectomized rats is not a result of lack of glucose; 2) chronic and, to an extent, acute treatment of fasted adrenalectomized rats with B enables survival; 3) fasted adrenalectomized rats exhibit strong evidence of hepatic insufficiency which is not apparent in either fed adrenalectomized rats or B-treated fasted adrenalectomized rats; 4) death after hemorrhage in fasted adrenalectomized rats may result from hepatic failure as a consequence of marked splanchnic vasoconstriction mediated bv the actions of extraordinarily high levels of vasoactive hormones after hemorrhage; and 5) B appears to act to decrease the magnitude of response of vasoactive hormones after hemorrhage in fasted adrenatectomized rats.

Darlington, Daniel N.↗