Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Complex Geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Calculation Accuracy and Efficiency of a Transient Model for Submerged Entry Nozzle Clogging

A transient numerical model was proposed and validated by the current authors for nozzle clogging (Barati et al. in Powder Technol 329:181-98, 2018). The model can reproduce the experiment in pilot scale satisfactorily. In the present article, the main objective is to validate the model for application in industry process continuous casting of steel, referring to the model accuracy and calculation efficiency. The results have shown that for the complex geometry of submerged entry nozzle (SEN), where it is difficult to create hexahedron mesh in the entire domain, a mixed mesh type is recommended, i.e., the wedge mesh for regions adjacent to SEN walls and the tetrahedron mesh for inner regions. Another challenge to the calculation of real SEN clogging is the huge number of particles involved in the industry process. An artificial factor, the N-factor, has to be introduced to reduce the calculation cost. A dimensionless number (α) is defined to limit the N-factor and ensure the modeling accuracy. Simulation of a test case has indicated that by an appropriate N-factor (1000, corresponding to α = 6 × 10{sup −5}), the calculation time would be reduced significantly to a reasonable time.

36 MATERIALS SCIENCE↗

Notch Tensile Behavior of the Mg-Zn-Gd-Zr Alloy

The Mg-Zn-Gd-Zr alloy is one of the important aerospace alloys in the aircraft gearbox applications. The complex geometry of the gearbox introduces several stress concentration points with various intensities. These regions are susceptible to catastrophic failure under mixed loading condition. Therefore, it is important to understand the deformation and failure mode of this alloy for various plastic constraint conditions. In the present work, Mg-4%Zn-1.5%Gd-0.5%Zr alloys were prepared with four different increasing notch root radii (1, 2, 4 and 8 mm). These samples were tested for tensile properties and compared with the smooth condition. In addition, notch sensitivity was determined analytically. The microstructure and fracture samples of the alloy were characterized with the aid of an optical/scanning electron microscope. Tensile test results show that the alloy is notch sensitive and shows notch-strengthening effects. The notch strength ratio increases with the decrease in the notch root radius due to the strong plastic constraint. The predicted and experimental results of the fracture strain with the notch root radius are in qualitative agreement. The void growth rate prediction is qualitatively in agreement with the tensile and fractography results and suggests that the notch geometry has a significant influence on the plastic strain of the alloy. The microstructure of the alloy has equiaxed grains of 74 ± 24 µm with the grain boundary eutectic. The eutectic is composed of Gd-rich Mg phase. The fracture surface has a distinct change from mixed mode to complete cleavage with the increasing notch root radius. The fractography results show that the fracture mode is predominantly intergranular for all the cases.

36 MATERIALS SCIENCE↗

Neutron Diffraction Analysis of Residual Strain in High-Pressure Die Cast A383 Engine Blocks

The residual strains in three high-pressure die cast A383 engine blocks were measured using neutron diffraction. Residual strains and stresses can be generated during high-pressure die casting process due to high thermal gradients and may cause fatigue failure or dimensional distortion. Neutron diffraction can measure the residual strain distributions deep inside castings with complex geometries, because neutrons can penetrate substantially more material than x-rays. In this paper, the residual strains (in the axial and hoop directions) along the whole cylinder bridge of high-pressure die cast A383 engine blocks in as-cast and heat-treated conditions were measured by neutron diffraction methods. The effect of heat treatment on the distribution and magnitude of residual strains was also investigated. The results indicate that the residual strain in the cylinder bridge is tensile in both the axial and hoop components for both the as-cast and the heat-treated engine blocks. The residual strain in the hoop direction is bigger in magnitude than the residual strain in the axial direction. Heat treatment significantly relaxes the residual strain in the axial direction but only slightly relaxes the residual strain in the hoop direction.

36 MATERIALS SCIENCE↗

Large deformation and brittle failure calculated using the dual-domain material point method

The dual domain material point (DDMP) method is explored as a candidate to be implemented in a general purpose code to perform simulations of materials with complex geometry that undergo large history-dependent deformation and failure. To test its candidacy, we study its mesh convergence, its sensitivity to mesh orientation, and its ability to handle softening and failure of a material. Simulations of large deformation and simulations of mechanical failure are performed using both DDMP and the material point method (MPM). When cell-crossing of material points is not an issue and when there are a sufficient number of material points in each computation cell, the numerical error decreases with the square of the cell size as expected for both MPM and DDMP. DDMP has reduced error compared with MPM when there are many instances of material points crossing cell boundaries due to the continuous nature of the modified gradient of the shape functions. Simulations of a specimen under tension are also performed where the background mesh is aligned and misaligned with the tension direction. MPM displays a significant mesh-dependent stress field, DDMP shows negligible mesh dependency. Despite a mesh orientation-dependent stress field from MPM, the critical tension and failure mode from both MPM and DDMP calculations have negligible mesh dependency when using a non-local failure model. If only the failure mode is important (i.e., local stresses are unimportant), MPM with a non-local failure model is a suitable method for modeling failure with small deformations. However, if local stresses are also important or if there are large deformations with many cell-crossings before failure, DDMP should be the method that is used. A needed improvement for DDMP is identified from our numerical simulations.

36 MATERIALS SCIENCE↗

Additively Manufactured Single-Use Molds and Reusable Patterns for Large Automotive and Hydroelectric Components

Additive manufacturing (AM) has the potential to reduce costs in the casting industry, particularly for large parts (i.e., components with any dimension > 12 in.). In this study, pilot-scale production case studies of hydroelectric and automotive parts were used to evaluate two AM-enabled casting methods: the direct printing of sand molds by binder jet and printing of reusable cope and drag patterns for sand casting. An additional benefit was found when additively manufactured patterns were used in combination with heat-treat free aluminum alloys, to produce castings of complex hydrodynamic surfaces. These parts previously required production via subtractive machining due to part distortion induced by the quench step of heat treatments. The machine types used for the three case studies are sand-binder jet, high-resolution polymer fused deposition modeling (FDM), and big area additive manufacturing (BAAM) FDM in combination with CNC machining. Each method demonstrated distinct advantages over traditional casting practices in particular use cases. Single-use molds show great reductions in start-up cost to produce one-off or legacy parts, and additively manufactured impression patterns show promise for innovating the tooling design process for complex geometry and large castings.

36 MATERIALS SCIENCE↗

Nickel-based superalloy single crystals fabricated via electron beam melting

Additive manufacturing technologies have emerged as potential disruptive processes whose possible impacts range from supply chain logistics, prototyping, and novel materials synthesis. Numerous works illustrate the ability to control mi- crostructure in fusion based processes and a few recent authors have even produced single crystals. However, a number of open questions remain regarding the process window which enables printing of single crystals. Furthermore, it has been observed that these additively manufactured single crystals exhibit a preferred $\langle$011$\rangle$ secondary orientation. In this work we investigate fabrication conditions which enable printing of single crystals via electron beam melting. A space filling design of experiments is utilized to efficiently explore the fabrication space. Single crystals were success- fully obtained using both commercially available powders and custom melt alloys. Microstructures obtained via these exploratory experiments exhibited a continuum of columnar structures ranging from weakly textured polycrystals, near single crystal, and fully single crystalline material. Complex geometry experiments are performed to study the grain selection mechanism. We find that the grain selection mechanism is independent of the bulk scale geometry and must therefore by driven by local heat transfer and solidification dynamics. Furthermore, grain selection is shown to be driven by competing driving forces; one which prefers epitaxial growth and another which is driven by the imposed scan pattern geometry. Finally, a mechanism is proposed for the anomalous secondary orientation preference.

36 MATERIALS SCIENCE↗

GrainPaint: A multi-scale diffusion-based generative model for microstructure reconstruction of large-scale objects

Simulation-based approaches to microstructure generation can suffer from a variety of limitations, such as high memory usage, long computational times, and difficulties in generating complex geometries. Generative machine learning models present a way around these issues, but they have previously been limited by the fixed size of their generation area. Here, we present a new microstructure generation methodology leveraging advances in inpainting using denoising diffusion models to overcome this generation area limitation. We show that microstructures generated with the presented methodology are statistically similar to grain structures generated with a kinetic Monte Carlo simulator, SPPARKS.

36 MATERIALS SCIENCE↗

A non-melting additive approach to structural repair of aluminum aircraft fastener holes

The damage to fastener holes in aerospace aluminum structures presents significant challenges for aircraft durability, and conventional bushing methods for repairing oversized holes often fall short due to the lack of metallurgical bonding and limited edge distance availability. This study investigates additive friction stir deposition, a non-melting additive process, as a viable alternative for the structural repair of aerospace fastener holes. The repair process, demonstrated on AA7050 (Al-Zn-Mg-Cu-Zr) hole structures, involves filling oversized holes with new material and machining to restore the original hole size. The repaired hole coupons are defect-free and exhibit good fatigue performance under fully reversed tension-compression loading (R = -1). At a nominal stress amplitude of 123.5 MPa, the average number of cycles to failure is 12,666 for unrepaired baseline coupons and 17,372 for effectively repaired coupons. Restoring complex geometries without compromising fatigue performance has been difficult in aerospace applications; this study marks the first demonstration of additive repair that consistently outperforms the unrepaired baseline coupons. Notably, the result is achieved through a low-energy, cost-effective solution without the need for post-repair heat treatment. Except for a few outliers, the post-repair fatigue performance generally remains inferior to that of undamaged, pristine coupons, likely due to precipitate evolution in AA7050 caused by the thermomechanical processing nature of additive friction stir deposition. This evolution weakens the repair region and the adjacent base material, leading to faster crack initiation and growth compared to the properly aged base material, AA7050-T7451.

36 MATERIALS SCIENCE↗

Microstructure-sensitive mechanical behavior of an additively manufactured psuedoelastic shape memory alloy

The additive manufacturing of shape memory alloys into complex geometries enables fabrication of advanced functional systems across a variety of fields and domains. This work presents results focused on the mechanical behavior of additively manufactured shape memory pseudoelastic NiTi. The deformation induced solid state phase transformation from austenite to martensite allows this system to accommodate large recoverable strains. This deformation behavior is fundamentally driven by crystal-scale transformation physics. Laser powder bed fusion processing reveals that the resulting microstructure, both grain morphology and crystallographic texture, is strongly dependent on the manufacturing processing history. Exhaustive mechanical testing demonstrates that these microstructural factors strongly impact both tensile and cyclic stress–strain behavior. Cyclic dissipative behavior, however, is similar across all tested microstructures following an initial transient period. Remarkably, analysis of spatial strain fields during tensile loading reveals two distinctly different localization “modes”. The first is initiation of localized deformation bands which continuously propagate through the tensile bar during loading. In the second mode localization is observed but lacks propagation; instead additional localization cites nucleate during subsequent loading. The latter phenomena is suspected to be driven by grain-scale deformation physics as the localized band morphologies coincide with grain morphologies. These phenomena strongly impact the resulting aggregate stress–strain behavior. Hence, manufacturers and designers of psuedoelastic functional components must at the very least consider the potential variability in properties when considering additive manufacturing processing. More ideally the process–structure–property relations can be used to further tailor and optimize final functional performance.

Additive manufacturing↗

Computational modeling of residual stress formation during the electron beam melting process for Inconel 718

Here, a computational modeling approach to simulate residual stress formation during the electron beam melting (EBM) process within the additive manufacturing (AM) technologies for Inconel 718 is presented in this paper. The EBM process has demonstrated a high potential to fabricate components with complex geometries, but the resulting components are influenced by the thermal cycles observed during the manufacturing process. When processing nickel based superalloys, very high temperatures (approx. 1000 °C) are observed in the powder bed, base plate, and build. These high temperatures, when combined with substrate adherence, can result in warping of the base plate and affect the final component by causing defects. It is important to have an understanding of the thermo-mechanical response of the entire system, that is, its mechanical behavior towards thermal loading occurring during the EBM process prior to manufacturing a component. Therefore, computational models to predict the response of the system during the EBM process will aid in eliminating the undesired process conditions, a priori, in order to fabricate the optimum component. Such a comprehensive computational modeling approach is demonstrated to analyze warping of the base plate, stress and plastic strain accumulation within the material, and thermal cycles in the system during different stages of the EBM process.

97 MATHEMATICS AND COMPUTING↗

A novel freeform extrusion fabrication process for producing solid ceramic components with uniform layered radiation drying

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. Heere in this process, an aqueous paste of ceramic particles with a very low binder content (<1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

36 MATERIALS SCIENCE↗

Infiltration studies of additive manufacture of WC with Co using binder jetting and pressureless melt method

Additive manufacturing (AM) of tungsten carbide-cobalt (WC-Co) is explored starting with WC preforms shaped with binder jet additive manufacturing (BJAM) followed by melt infiltration of Co. The research objective is to demonstrate the ability to net-shape WC-Co composites through BJAM of a WC preform followed by backfilling with cobalt via pressureless infiltration. This method also has the potential to minimize shrinkage and grain growth compared to other AM techniques. The effects of sintering, Co content, and infiltration time on the net shaping and properties of processed composites are shown. The best shaped material had an average grain size of 5.1 μm, 32 vol.% Co, density of 98.54% theoretical, fracture toughness of 23.2 MPa m 1/2 , and hardness of 9.0 GPa. Data presented illustrates that the proposed approach results in favorable ceramic-metal (cermet) properties and is viable for fabricating cermets of other material combinations. Furthermore successful AM of cermets provides complex geometries, high throughout, and low costs.

36 MATERIALS SCIENCE↗

Correlations between thermal history and keyhole porosity in laser powder bed fusion

Additive manufacturing has the potential to revolutionize the production of metallic components as it yields near net shape parts with complex geometries and minimizes waste. At the present day, additively manufactured components face qualification and certification challenges due to the difficulty in controlling defects. This has driven a significant research effort aimed at better understanding and improving processing controls – yielding a plethora of in-situ measurements aimed at correlating defects with material quality metrics of interest. In this work, we develop machine-learning methods to learn correlations between thermal history and subsurface porosity for a variety of print conditions in laser powder bed fusion. Un-normalized surface temperatures (in the form of black-body radiances) are obtained using high-speed infrared imaging and porosity formation is observed in the sample cross-section through synchrotron x-ray imaging. To demonstrate the predictive power of these features, we present four statistical machine-learning models that correlate temperature histories to subsurface porosity formation in laser fused Ti-6Al4V powder.

36 MATERIALS SCIENCE↗

Island scanning pattern optimization for residual deformation mitigation in laser powder bed fusion via sequential inherent strain method and sensitivity analysis

Laser powder bed fusion (L-PBF) has emerged as one of the mainstream additive manufacturing approaches for fabricating metal parts with complex geometries and intricate internal structures. However, large deformation associated with rapid heating and cooling can lead to build failure and requires post-processing which may increase manufacturing cost and prolong the production period. Here in this work, an island scanning pattern design method is proposed to optimize the scanning direction of each island in order to reduce part deformation after cutting off the build platform. The objective of this optimization is to minimize the upward bending of the part after sectioning, which allows the part deformation to satisfy the tolerance requirement or reduce the post heat treatment time. Inherent strain method is employed in the sequential finite element analysis consisting of layer-by-layer activations and sectioning for fast residual distortion prediction. Full sequential sensitivity analysis for the formulated optimization is provided to update the island scanning directions. To show the feasibility and effectiveness of the proposed method, the scanning patterns of a block structure and a connecting rod were designed and parts were fabricated using an open architecture L-PBF machine. The fabrication experiments demonstrated that the residual deformation of both parts fabricated by optimized scanning pattern can be reduced by over 50% compared to the initial scanning patterns, which demonstrate the effectiveness of the proposed method.

36 MATERIALS SCIENCE↗

A new procedure for implementing the modified inherent strain method with improved accuracy in predicting both residual stress and deformation for laser powder bed fusion

As a metal additive manufacturing (AM) process, laser powder bed fusion (L-PBF) has been widely used to produce parts with complex geometries. The large thermal gradient caused by the fast, intense, and repeated laser scanning induces significant residual deformation and stress to the as-built parts, which increase manufacturing difficulty and geometrical inaccuracy as a result. The modified inherent strain (MIS) method exploiting multiscale process simulations was developed to simulate residual deformation accurately and efficiently. However, the existing procedure of implementing the MIS method is found to give inaccurate residual stress prediction. Here in this work, a new implementation procedure for the MIS method is proposed to improve the simulation accuracy of residual stress without degrading the residual deformation prediction. The new procedure concerns the application of inherent strains to the part-scale layer-by-layer finite element model to obtain residual stress and deformation field. While the existing implementation of the part-scale MIS model involves only mechanical properties at ambient temperature, the new procedure adds one more solution step employing mechanical properties at an elevated temperature determined from the inherent strain extraction step. Both numerical and experimental studies are conducted to validate the proposed new implementation procedure. It shows that by using the new procedure, the MIS-based simulation can predict both residual stress and deformation of as-built L-PBF metal parts with good accuracy.

36 MATERIALS SCIENCE↗

Developing ductile and isotropic Ti alloy with tailored composition for laser powder bed fusion

Laser powder bed fusion (LPBF) is an advanced technology to create metallic components with complex geometry. Ti-6Al-4V (Ti64) is one of the most frequently used materials for LPBF. The intrinsic high cooling rates and ultra-high directional thermal gradient of melt, however, lead to a hierarchical structure composed of fine martensitic alpha' within columnar prior-beta grains in LPBF Ti64. This microstructure results in poor ductility and strong mechanical anisotropy in as-built Ti64 components, which largely limit their applications. Here, we report that the above shortcomings can be overcome by tailoring the alloy composition. Specifically, by reducing the aluminum content from 6 wt% to 4 wt%, the resultant LPBF Ti-4Al-4V (Ti44) alloy exhibits substantially improved ductility and mechanical isotropy. These improvements are attributed to grain refinement during solidification and the activation of multiple slip modes and twinning in the as-built material during deformation. This work offers a simple strategy to design new titanium alloys for LPBF with significantly improved ductility and isotropy.

36 MATERIALS SCIENCE↗

Measuring thermomechanical response of large-format printed polymer composite structures via digital image correlation

Large-format additive manufacturing (LFAM) is a branch of additive manufacturing (AM) research with the ability to create large structures typically measuring several meters in scale. LFAM is advantageous for tooling applications, not only because it offers the ability to create complex geometries not easily made using subtractive manufacturing processes, but the cost savings of pelletized feedstock used by these systems result in larger parts printed at faster speeds than traditional AM systems. Fiber reinforced polymer (FRP) is a commonly used feedstock material in LFAM structures because it reduces the distortion experienced during printing. However, FRP introduces highly anisotropic thermomechanical properties and contributes to a nonhomogeneous microstructure that can result in critical distortion of dimensions during tooling. Measuring the global thermomechanical response of LFAM structures requires a more representative method that accounts for not only anisotropic properties but also the nonhomogeneous nature of the final part. This is where traditional techniques to measure thermomechanical response, such as thermomechanical analysis (TMA), fall short as they assume homogeneity. This study evaluated the coefficient of thermal expansion (CTE) of LFAM structures as measured by TMA as compared to a novel digital image correlation oven (DIC Oven) system. The LFAM structures were made from 20 % by weight carbon fiber reinforced acrylonitrile butadiene styrene (CF-ABS). TMA measurements showed significant variations in CTE across a single LFAM bead, confirming the need for a global technique that captures overall thermomechanical response. The CTE values measured using the DIC Oven compared well to average TMA values obtained from localized measurements across the sample. The DIC Oven was also used to quantify the effects of different layer orientations on thermomechanical properties, which cannot be easily captured using TMA. A predictive model was also developed by using localized TMA values across an LFAM bead to predict the overall thermomechanical response of an LFAM structure.

36 MATERIALS SCIENCE↗