SEARCH · Engineering Papers

Results for “Camber”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Experimental trim drag values for conventional and supercritical wings

Supercritical wings were studied to determine whether they incur higher trim drag values at cruise conditions than wide body technology wings. Relative trim drag increments were measured in an experimental wind tunnel investigation. The tests utilized high aspect ratio supercritical wing and a wide body wing in conjunction with five different horizontal tail configurations, mounted on a representative wide body fuselage. The three low tail configurations and two T tail configurations were chosen to measure the effects on horizontal tail size, location, and camber on the trim drag increments for the two wings. The increase in performance (lift to drag ratio) for supercritical wing over the wide body wing was 11 percent for both the optimum low tail and T tail configurations.

Jacobs, P. F.↗

NASA NTRS1982

Transonic pressure measurements and comparison of theory to experiment for three arrow-wing configurations

Wind tunnel tests of arrow-wing body configurations consisting of flat, twisted, and cambered twisted wings, as well as a variety of leading and trailing edge control surface deflections, were conducted at Mach numbers from 0.4 to 1.05 to provide an experimental pressure data base for comparison with theoretical methods. Theory to experiment comparisons of detailed pressure distributions were made using state of the art attached flow methods. Conditions under which these theories are valid for these wings are presented.

Manro, M. E.↗

NASA NTRS1982

Aerodynamic performance of slender wings with separated flows

The aerodynamic performance of low aspect ratio sweptback wings with vortex flows was numerically investigated using the free vortex sheet method. The models studied included flat, cambered, strake, and leading edge flapped wings of different planforms. The theoretical results predicted by the method were compared with the existing experimental data wherever available; and the code capabilities and limitations were explored. Also the effects of the wing thickness, fuselage, leading edge flap and multiple vortex modeling on the aerodynamic characteristics were studied.

Reddy, C. S.↗

NASA NTRS1982

Structural dynamics of shroudless, hollow fan blades with composite in-lays

Structural and dynamic analyses are presented for a shroudless, hollow titanium fan blade proposed for future use in aircraft turbine engines. The blade was modeled and analyzed using the composite blade structural analysis computer program (COBSTRAN); an integrated program consisting of mesh generators, composite mechanics codes, NASTRAN, and pre- and post-processors. Vibration and impact analyses are presented. The vibration analysis was conducted with COBSTRAN. Results show the effect of the centrifugal force field on frequencies, twist, and blade camber. Bird impact analysis was performed with the multi-mode blade impact computer program. This program uses the geometric model and modal analysis from the COBSTRAN vibration analysis to determine the gross impact response of the fan blades to bird strikes. The structural performance of this blade is also compared to a blade of similar design but with composite in-lays on the outer surface. Results show that the composite in-lays can be selected (designed) to substantially modify the mechanical performance of the shroudless, hollow fan blade.

Aiello, R. A.↗

NASA NTRS1981

Recent Darrieus vertical axis wind turbine aerodynamical experiments at Sandia National Laboratories

Experiments contributing to the understanding of the aerodynamics of airfoils operating in the vertical axis wind turbine (VAWT) environment are described. These experiments are ultimately intended to reduce VAWT cost of energy and increase system reliability. They include chordwise pressure surveys, circumferential blade acceleration surveys, effects of blade camber, pitch and offset, blade blowing, and use of sections designed specifically for VAWT application.

Klimas, P. C.↗

NASA NTRS1982

F-16E program overview and wind tunnel/flight correlation

Correlation is defined in three different ways: comparisons of wind tunnel and/or theory with flight results; detailed studies of total vehicle drag from wind tunnel and flight tests; and attempts to understand the fundamental mechanisms of fluid flows associated with aircraft components in specific areas of the flight environment. The F-16E configuration is an outgrowth of studies conducted to produce a refined fighter wing design. Several iterations required to arrive at the combination of wing planform, camber, and twist which gives near optimum lift, drag, and high-angle-of-attack stability. Theoretical analyses were backed up by extensive experimental data to validate the design and are presented

Madsen, A. P.↗

NASA NTRS1982

X-29A forward-swept-wing demonstrator airplane

The X-29A is a technology demonstrator. The FSW is just one of the technologies. Others include the following: discrete variable camber, relaxed static stability, triplex digital fly-by-wire (FBW) control system, variable-incidence/close-coupled canard, aeroelastically tailored composite wing, and thin supercritical airfoil. The growth potential for additional technologies is shown.

Frei, D. R.↗

NASA NTRS1982

Production version of the extended NASA-Langley Vortex Lattice FORTRAN computer program. Volume 1: User's guide

The latest production version, MARK IV, of the NASA-Langley vortex lattice computer program is summarized. All viable subcritical aerodynamic features of previous versions were retained. This version extends the previously documented program capabilities to four planforms, 400 panels, and enables the user to obtain vortex-flow aerodynamics on cambered planforms, flowfield properties off the configuration in attached flow, and planform longitudinal load distributions.

Lamar, J. E.↗

NASA NTRS1982

An experimental investigation of gapwise periodicity and unsteady aerodynamic response in an oscillating cascade. 1: Experimental and theoretical results

Tests were conducted on a linear cascade of airfoils oscillating in pitch to measure the unsteady pressure response on selected blades along the leading edge plane of the cascade, over the chord of the center blade, and on the sidewall in the plane of the leading edge. The pressure data were reduced to Fourier coefficient form for direct comparison, and were also processed to yield integrated loads and, particularly, the aerodynamic damping coefficient. Results from the unsteady Verdon/Caspar theory for cascaded blades with nonzero thickness and camber were compared with the experimental measurements. The three primary results are: (1) from the leading edge plane blade data, the cascade was judged to be periodic in unsteady flow over the range of parameters tested; (2) the interblade phase angle was found to be the single most important parameter affecting the stability of the oscillating cascade blades; and (3) the real blade theory and the experiment were in excellent agreement for the several cases chosen for comparison.

Carta, F. O.↗

NASA NTRS1982

Energy efficient engine: Turbine transition duct model technology report

The Low-Pressure Turbine Transition Duct Model Technology Program was directed toward substantiating the aerodynamic definition of a turbine transition duct for the Energy Efficient Engine. This effort was successful in demonstrating an aerodynamically viable compact duct geometry and the performance benefits associated with a low camber low-pressure turbine inlet guide vane. The transition duct design for the flight propulsion system was tested and the pressure loss goal of 0.7 percent was verified. Also, strut fairing pressure distributions, as well as wall pressure coefficients, were in close agreement with analytical predictions. Duct modifications for the integrated core/low spool were also evaluated. The total pressure loss was 1.59 percent. Although the increase in exit area in this design produced higher wall loadings, reflecting a more aggressive aerodynamic design, pressure profiles showed no evidence of flow separation. Overall, the results acquired have provided pertinent design and diagnostic information for the design of a turbine transition duct for both the flight propulsion system and the integrated core/low spool.

Leach, K.↗

NASA NTRS1982

Subsonic 3-D surface panel method for rapid analysis of multiple geometry perturbations

For any baseline aircraft configuration, a matrix of partial derivatives of surface velocity potential with respect to geometry coordinates is calculated. Linear extrapolation is then used to analyze the subcritical potential flow corresponding to a series of arbitrary small geometry perturbations. Each perturbation analysis is more than an order of magnitude more efficient than a conventional panel method solution because no influence coefficients are calculated and no large system of linear algebraic equations is solved. Wing and wing-fuselage examples are presented to demonstrate that the predicted pressure distributions are nearly exact for large changes to wing camber, thickness, and leading edge radius.

Bristow, D. R.↗

NASA NTRS1982

Wind-tunnel wall interference corrections for three-dimensional flows

A procedure for the evaluation of wall interference corrections for three-dimensional aircraft configurations is presented. The Mach number and angle-of-attack corrections are obtained by numerically solving the Laplace equation in a parallelepiped with boundary conditions supplied mainly from experimental pressure measurements. A portion of these measurements and other wind-tunnel data required by the procedure may be replaced by theoretical estimates if not available from experiments. The accuracy of the correction results will then depend on the accuracy of these estimates. The correction procedure is applied to an isolated wing and to a wing-tail configuration in a solid-wall wind tunnel. It is found that neglecting twist and camber corrections for the wing effectively increases the tail angle-of-attack correction. Two different Mach number corrections can be calculated for the wing and tail. However, since only one Mach number correction is allowed for both the wing and the tail, and since the wing surface area is larger than the tail surface area, the final correction tends to be closer to the required wing correction. This is a source of error for the tail results.

Rizk, M. H.↗

NASA NTRS1982

Generation of three-dimensional boundary-fitted curvilinear coordinate systems for wing/wing-tip geometries using the elliptic solver method

A three-dimensional elliptic solver technique is utilized to generate surface-fitted coordinates about wing/wing-tip configurations. The method is applicable to wings of arbitrary section profile and camber, leading-edge sweep, taper ratio, and spanwise thickness variation. The basic theory of three-dimensional elliptic mappings is developed along with a method to compute interior coordinate control functions. Examples of grids generated about several wing/wing-tip geometries are given. A 49 x 33 x 17 grid requires about 3 minutes of CPU time on a CYBER 203 computer.

Thames, F. C.↗

NASA NTRS1982

The use of linearized-aerodynamics and vortex-flow methods in aircraft design /invited paper/

This paper deals with selected linearized-aerodynamic and vortex-flow methods as applied to aircraft design problems at high subsonic speeds. In particular, the NASA Vortex Lattice and Modified Multhopp methods are the linearized techniques employed, and the suction analogy is used to provide estimates associated with vortex-flow aerodynamics. Many examples are given as to how researchers at Langley have used these methods to design the high subsonic, wing-mean-camber shapes for various configurations such as a supersonic transport, high-aspect-ratio transport, trapezoidal fighter wing, strake wing, tandem wing, joined wing, delta wing, and slender cranked wing. Many of these have been built, tested, and have had their data compared with theory. In addition, a technique for defining efficiently performing strake planforms for use in strake-wing combinations is discussed, and further improvements in wing design are outlined. The latter may be obtained by using higher-ordered linear panel methods as well as nonlinear-transonic methods.

Lamar, J. E.↗

NASA NTRS1982

Computational and experimental studies of light twin aerodynamic interference

The results of an analytical and experimental study of aerodynamic interference effects for a light twin aircraft are presented. Both the influence of a body (either fuselage or nacelle) on a wing and the influence of a wing on a body are studied. The wing studied uses a new natural laminar flow airfoil with variable camber movable trailing edge. A three-dimensional panel method program utilizing surface source and surface doublet singularities was used to design wing-nacelle and wing-fuselage fairings. Experiments were conducted using a 1/6 scale reflection plane model. Forces, pressures, and surface flow visualization results are presented. Results indicate that potential flow analysis is useful to guide the design of intersection fairings, but experimental tuning is still required. While the study specifically addressed a light twin aircraft, the methods are applicable to a wide variety of aircraft.

Thomson, W. G.↗

NASA NTRS1982

Wind-tunnel investigation of vortex flaps on a highly swept interceptor configuration

A subsonic wind-tunnel investigation of the application of vortex flaps to a supersonic interceptor configuration is described. Experimental results are presented which indicate the aerodynamic effects of vortex-flap deflection, trailing-edge flap deflection, vortex flap chord and span, vertical stabilizers, and a highly cambered leading edge designed for attached flow. Data presented include longitudinal forces and moments, upper-surface pressure distributions, and oil- and smoke-flow visualization photographs. It is concluded that a full-span deployable vortex flap can provide a substantial performance improvement for this and other similar configurations.

Schoonover, W. E., Jr.↗

NASA NTRS1983

Wing Subsonic Aerodynamic Performance Estimates

Solution by iteration estimates performance of twisted and cambered wings of arbitrary planform. SUBAER based on linearized theory lifting-surface solution provides spanwise distribution of theoretical leading edge thrust, in addition to surface distribution of perturbation velocities. Program written in FORTRAN IV.

Carlson, H. W.↗

NASA NTRS1978

The NASA supercritical-wing technology

A number of high aspect ratio supercritical wings in combination with a representative wide body type fuselage were tested in the Langley 8 foot transonic pressure tunnel. The wing parameters investigated include aspect ratio, sweep, thickness to chord ratio, and camber. Subsequent to these initial series of tests, a particular wing configuration was selected for further study and development. Tests on the selected wing involved the incorporation of a larger inboard trailing edge extension, an inboard leading edge extension, and flow through nacelles. Range factors for the various supercritical wing configurations are compared with those for a reference wide body transport configuration.

Bartlett, D. W.↗