SEARCH · Engineering Papers

Results for “CONTROL DEVICE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Energy Efficient High-Pressure Turbine Leakage Technology Report

The leakage test program was one of such supporting technology programs structured to provide guidance to the Energy Efficient Engine High Pressure Turbine Component Design Effort. Leakage reduction techniques were identified and evaluated. Test models were used to simulate component leak paths and to evaluate leakage reduction techniques. These models simulated the blade/disk attachment, the vane inner platform attachment, and the vane outer platform attachment combined with the blade outer airseal. Disk blade attachment testing indicated that leakage in this area could be reduced to very low levels by paying careful attention to the tolerances along the contact surface between the blade vibration damper and the blade platform contact surface. The aim of feather seal testing was to achieve a goal for an effective leakage gap of one mil (.001 inch) per inch of feather seal length. Results indicated that effective gaps even below the goal level were achievable by (1) maintaining close tolerances between feather seals and their slots to minimize end gaps and limit seal rotation, (2) avoiding feather seal overlap, and (3) minimizing feather seal intersections. W seals were shown to be effective leakage control devices. Wire rope, in its present state of development, was shown not to be an effective sealing concept for application to the component design.

Gardner, W. B.↗

NASA NTRS1983

Effect of tail-fin span on stability and control characteristics of a Canard-controlled missile at supersonic Mach numbers

An experimental wind-tunnel investigation was conducted at Mach numbers from 1.60 to 3.50 to obtain the longitudinal and lateral-directional aerodynamic characteristics of a circular, cruciform, canard-controlled missile with variations in tail-fin span. In addition, comparisons were made with the experimental aerodynamic characteristics using three missile aeroprediction programs: MISSILE1, MISSILE2, and NSWCDM. The results of the investigation indicate that for the test Mach number range, canard roll control at low angles of attack is feasible on tail-fin configurations with tail-to-canard span ratios of less than or equal to 0.75. The conards are effective pitch and yaw control devices on each tail-fin span configuration tested. Programs MISSILE1 and MISSILE2 provide very good predictions of longitudinal aerodynamic characteristics and fair predictions of lateral-directional aerodynamic characteristics at low angles of attack, with MISSILE2 predictions generally in better agreement with test data. Program NSWCDM provides good longitudinal and lateral-directional aerodynamic predictions that improve with increases in tail-tin span.

Blair, A. B., Jr.↗

NASA NTRS1983

Effects of wind on turbofan engines in outdoor static test stands

Wind can affect measured thrust and can cause turbofan engine speed to fluctuate during outdoor testing. Techniques used at an outdoor test stand at NASA Lewis Research Center to make testing easier and faster and to improve data repeatability include using an inflow control device (ICD) to make fan speed steadier, taking many raw data samples for better averaging, and correcting thrust for wind direction and speed. Data from engine tests are presented to show that the techniques improve repeatability of thrust and airflow measurements under various wind conditions.

Mcardle, J. G.↗

NASA NTRS1983

Flight effects on fan noise with static and wind tunnel comparisons

A flight test program utilizing a JT15D-1 turbofan engine has been conducted with the objectives of studying flight effects on fan noise and evaluating the simulation effectiveness of both a wind tunnel and a static test configuration that incorporated an inlet control device (ICD). In conjunction with synchronized laser-radar tracking and meteorological profile information, data obtained from a linear array of ground microphones was narrowband-analyzed and ensemble-averaged to yield highly accurate far-field flight acoustic results. Utilizing appropriate corrections, flight, wind tunnel, and static acoustic data were normalized to a static-equivalent, 100-foot radius, lossless reference condition. Data comparisons showed that both the static test with ICD and wind tunnel were generally very effective in simulating flight blade-passage-frequency (BPF) noise levels. However, differences were observed in broadband noise levels and in the details of the multiple-pure-tone harmonics.

Preisser, J. S.↗

NASA NTRS1984

Antimisting kerosene: Base fuel effects, blending and quality control techniques

The problems associated with blending of the AMK additive with Jet A, and the base fuel effects on AMK properties are addressed. The results from the evaluation of some of the quality control techniques for AMK are presented. The principal conclusions of this investigation are: significant compositional differences for base fuel (Jet A) within the ASTM specification DI655; higher aromatic content of the base fuel was found to be beneficial for the polymer dissolution at ambient (20 C) temperature; using static mixer technology, the antimisting additive (FM-9) is in-line blended with Jet A, producing AMK which has adequate fire-protection properties 15 to 20 minutes after blending; degradability of freshly blended and equilibrated AMK indicated that maximum degradability is reached after adequate fire protection is obtained; the results of AMK degradability as measured by filter ratio, confirmed previous RAE data that power requirements to decade freshly blended AMK are significantly higher than equilibrated AMK; blending of the additive by using FM-9 concentrate in Jet A produces equilibrated AMK almost instantly; nephelometry offers a simple continuous monitoring capability and is used as a real time quality control device for AMK; and trajectory (jet thurst) and pressure drop tests are useful laboratory techniques for evaluating AMK quality.

Yavrouian, A. H.↗

NASA NTRS1984

Design and test of a low-temperature liner driver/rate controller

The design and testing of a force/rate control device used to deploy an Earth shield on an orbiting satellite is described. Test experience, failure modes, and applications are emphasized.

Lowry, C. H.↗

NASA NTRS1984

Dielectric cure monitoring: Preliminary studies

Preliminary studies have been conducted on two types of dielectric cure monitoring systems employing both epoxy resins and phenolic composites. An Audrey System was used for 23 cure monitoring runs with very limited success. Nine complete cure monitoring runs have been investigated using a Micromet System. Two additional measurements were performed to investigate the Micromet's sensitivity to water absorption in a post-cure carbon-phenolic material. While further work is needed to determine data significance, the Micromet system appears to show promise as a feedback control device during processing.

Goldberg, B. E.↗

NASA NTRS1984

High Power K Sub a -band Transmitter for Planetary Radar and Spacecraft Uplink

A proposed conceptual design of a 400 kW continuous wave (CW)K sub a band transmitter and associated microwave components to be used for planetary radar and serve as a prototype for future spacecraft uplinks is discussed. System requirements for such a transmitter are presented. Performance of the proposed high-power millimeter wave tube, the gyroklystron is discussed. Parameters of the proposed power amplifier, beam supply, and monitor and control devices are also presented. Microwave transmission line components consisting of signal monitoring devices, signal filtering devices, and an overmoded corrugated feed are discussed. Finally, an assessment of the state of the art technology to meet the system requirements is given and possible areas of difficulty are summarized.

Bhanji, A. M.↗

NASA NTRS1983

Effects of wind on turbofan engines in outdoor static test stands

Mcardle, J. G.↗

NASA NTRS1985

Flow control in a diffusing S-Duct

Accurate measurements have been made of secondary flow in a 1.51 area ratio diffusing 30 deg - 30 deg S-Duct with circulair cross section. Turbulent flow was entering the duct at Mach number of 0.6, the boundary layer thickness at the duct entrance was ten percent of the duct inlet diameter. Through measurements made, local flow velocity vector as well as static and total pressures mapping of the flow at several stations were obtained. Strong secondary flow was measured in the first bend which continued into the second bend with new vorticity produced in there in the opposite direction. Surface oil flow visualization and wall pressures indicated a region of separated flow starting at theta approximately equal to 22 deg on the inside of the first bend up to theta approximately equal to 44 deg on the outside of the second bend. The flow separated in 'cyclone' form and never reattached in the duct. As a result of the secondary flow and the flow separation, significant total pressure distortion was observed at the exit of the duct. Using flow control devices the separation was eliminated while the exit distortion was improved.

Vakili, A. D.↗

NASA NTRS1985

Supersonic aerodynamic characteristics of some reentry concepts for angles of attack up to 90 deg

Past studies of reentry vehicles tested to high angles of attack (up to 90 deg) in the Mach number range from 2 to 4.8 have provided some fundamental insights into the aerodynamic characteristics of such vehicles. Two basic planforms are considered in this paper: highly swept deltas, and circular. The delta concepts include variations in cross section (and thus volume) and in camber distribution. The effectiveness of various types of aerodynamic control devices is also included. The purpose of the paper is to examine the characteristics of the vehicles with a view toward the potential usefulness of such concepts in a flight regime that would include reentry from space into the atmosphere, followed by a transition to sustained atmospheric flight.

Spearman, M. L.↗

NASA NTRS1986

Dual-Flow-Rate Valve

Flow-control device precisely adjusted for two rates. Heart of twoposition valve is sliding poppet. At far-right position, poppet allows low flow. At far-left position, allows high flow. Valve supplies high-pressure gas at either of two preselected flow rates. Valve adjustable between 0.12 and 1.2 lb/s (0.054 and 0.54 kg/s) of hydrogen at 3,300 lb/in.2 (23 MN/m2) and 80 degrees F (27 degrees C). Two flow rates preadjusted between these limits in increments of 0.01 lb/s (0.0045 kg/s).

Allbritain, R. H.↗

NASA NTRS1985

Supersonic aerodynamic characteristics of some reentry concepts for angles of attack to 90 deg

Past studies of reentry vehicles tested to high angles of attack (up to 90 deg) in the Mach number range from 2 to 4.8 are reviewed. Two basic planforms are considered: highly-swept deltas and circular. The delta concepts include variations in cross section (and thus volume) and in camber distribution. The effectiveness of various types of aerodynamic control devices is also included. The purpose of the paper is to examine the characteristics of the vehicles with a view toward the potential usefulness of such concepts in a flight regime that would include reentry from space into the atmosphere followed by a transition to sustained atmospheric flight.

Spearman, M. L.↗

NASA NTRS1986

Statistical prediction of dynamic distortion of inlet flow using minimum dynamic measurement. An application to the Melick statistical method and inlet flow dynamic distortion prediction without RMS measurements

The Melick method of inlet flow dynamic distortion prediction by statistical means is outlined. A hypothetic vortex model is used as the basis for the mathematical formulations. The main variables are identified by matching the theoretical total pressure rms ratio with the measured total pressure rms ratio. Data comparisons, using the HiMAT inlet test data set, indicate satisfactory prediction of the dynamic peak distortion for cases with boundary layer control device vortex generators. A method for the dynamic probe selection was developed. Validity of the probe selection criteria is demonstrated by comparing the reduced-probe predictions with the 40-probe predictions. It is indicated that the the number of dynamic probes can be reduced to as few as two and still retain good accuracy.

Schweikhard, W. G.↗

NASA NTRS1985

Measurements of concentrations of chlorofluoromethanes (CFMs) carbon dioxide and carbon isotope ratio in stratospheric and tropospheric air by grab-sampling systems

Measurements of concentrations of chlorofluoromethanes (CFMs), carbon dioxide and carbon isotope ratio in stratospheric and tropospheric air by grab-sampling systems are reported. The balloon-borne grab-sampling system has been launched from Sanriku Balloon Center three times since 1981. It consists of: (1) six sampling cylinders, (2) eight motor driven values, (3) control and monitor circuits, and (4) pressurized housing. Particular consideration is paid to the problem of contamination. Strict requirements are placed on the choice of materials and components, construction methods, cleaning techniques, vacuum integrity, and sampling procedures. An aluminum pressurized housing and a 4-m long inlet line are employed to prevent the sampling air from contamination by outgassing of sampling and control devices. The sampling is performed during the descent of the system. Vertical profiles of mixing ratios of CF2Cl2, CFCl3 and CH4 are given. Mixing ratios of CF2Cl2 and CFCl3 in the stratosphere do not show the discernible effect of the increase of those in the ground level background, and decrease with altitude. Decreasing rate of CFCl3 is larger than that of CF2Cl2. CH4 mixing ratio, on the other hand, shows diffusive equilibrium, as the photodissociation cross section of CH4 is small and concentrations of OH radical and 0(sup I D) are low.

Itoh, T.↗

NASA NTRS1985

A theory for lateral wing-tip blowing

The concept of lateral blowing consists in utilizing thin jets of air, which are ejected in the spanwise direction from slots at the tips of straight and swept wings, or along the leading edges of delta wings, to generate aerodynamic forces without the assistance of deflecting solid surfaces. For weak intensities of blowing the so-generated forces could be used for roll and lateral control of aircraft. In this work a theory for this concept as applied to straight wings is presented, revealing the analytical relationship between blowing and aerodynamic forces. The approach is based on perturbing the span of an elliptically loaded wing. Scaling laws involving blowing intensity, aspect ratio, and angle of attack are derived and compared with experiments. It is concluded that this concept has potential as a novel roll and lateral control device.

Tavella, D.↗

NASA NTRS1985

High power Ka-band transmitter for planetary radar and spacecraft uplink

A proposed conceptual design of a 400 kW CW Ka-Band transmitter and associated microwave components to be used for planetary radar and serve as a prototype for feature spacecraft uplinks is discussed. System requirements for such a transmitter are presented. Performance of the proposed high power millimeter wave tube, the gyroklystron, is discussed. Parameters of the proposed power amplifier, beam supply, and monitor and control devices are also presented, Microwave transmission line components consisting of signal monitoring devices, signal filtering devices, and an overmoded corrugated feed are discussed. Finally, an assessment of the state of the art technology to meet the system requirements is given and possible areas of difficulty are summarized.

Bhanji, A.M.↗

NASA NTRS1986

Subsonic aerodynamic characteristics of a circular body earth-to-orbit transport

To reduce the weight and improve the performance of future earth-to-orbit transports, the use of circular cross sections in the fuselage bodies of these vehicles is being considered at the Langley Research Center. Structurally, circular cross sections are stronger and lighter than other shapes. A study has been made applying the circular body concept to a vertical-takeoff, delta-winged, single-stage-to-orbit transport. A 52 in., 0.022-scale model of the circular body vehicle was tested at a Mach number of 0.3 in the 7 x 10 ft High Speed Wind Tunnel at the Langley Research Center to obtain aerodynamic forces and moments. Oil-flow photographs were taken at several angles of attack to aid in the aerodynamic analysis. Model control surfaces included elevons and ailerons for the evaluation of pitch and roll characteristics and either wing-tip fins, a nose mounted dorsal fin, or a conventional vertical tail for the evaluation of yaw characteristics. Other deflecting surfaces included speedbrakes and body flaps. Basic data on longitudinal flight characteristics are shown, including lift, drag, and pitching moments. Comparisons of the directional stability and control effectiveness of the three directional control devices are also shown.

Lepsch, R. A., Jr.↗