Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

Hydrodynamics of binary coalescence. 1: Polytropes with stiff equations of state

We performed a series of three-dimensional hydrodynamic calculations of binary coalescence using the smoothed particle hydrodynamics (SPH) method. The initial conditions are exact polytropic equilibrium configurations on the verge of dynamical instability. We consider synchronized equilbria only and concentrate on stiff equations of state, with adiabatic Gamma greater than 5/3. We assume that the polytropic constants (K identically equal to P/(rho(exp Gamma)) are the same for both components. These conditions apply well to models of neutron star binaries. Accordingly, we discuss our results in the context of the Laser Interferometer Gravitational-Wave Observatory (LIGO) project, and we calculate the emission of gravitational radiation in the quadruple approximation. The fully nonlinear development of the instability is followed using SPH until a new equilibrium configuration is reached by the system. We find that the properties of this final configuration depend sensitively on both the compressibility and mass ratio. An axisymmetric merged configuration is always produced when the adiabatic exponent Gamma approximately less than 2.3. As a consequence, the emission of gravitational radiation shuts off abruptly right after the onset of dynamical instability. In contrast, triaxial merged configurations are obtained when Gamma approximately greater than 2.3, and the system continues to emit gravitational waves after the final coalescence. Systems with mass ratios q not equal to 1 typically become dynamically unstable before the onset of mass transfer. Stable mass transfer from one neutron star to another in a close binary is therefore probably ruled out. For a mass ratio q approximately less than 0.5, however, dynamical mass transfer can temporarily retard the coalescence by causing a rapid reexpansion of the binary into a new, slightly eccentric but dynamically stable orbit. The maximum amplitude h(sub max) and peak luminosity L(sub max) of the gravitational waves emitted during the final coalescence are nearly independent of Gamma, but depend sensitively on the mass ratio q. The approximate scalings we find are h(sub max) varies as q(exp 2) and L(sub max) varies as q(exp 6) for q close to unity.

Rasio, Frederic A.↗

Control-Relevant Modeling, Analysis, and Design for Scramjet-Powered Hypersonic Vehicles

Within this paper, control-relevant vehicle design concepts are examined using a widely used 3 DOF (plus flexibility) nonlinear model for the longitudinal dynamics of a generic carrot-shaped scramjet powered hypersonic vehicle. Trade studies associated with vehicle/engine parameters are examined. The impact of parameters on control-relevant static properties (e.g. level-flight trimmable region, trim controls, AOA, thrust margin) and dynamic properties (e.g. instability and right half plane zero associated with flight path angle) are examined. Specific parameters considered include: inlet height, diffuser area ratio, lower forebody compression ramp inclination angle, engine location, center of gravity, and mass. Vehicle optimizations is also examined. Both static and dynamic considerations are addressed. The gap-metric optimized vehicle is obtained to illustrate how this control-centric concept can be used to "reduce" scheduling requirements for the final control system. A classic inner-outer loop control architecture and methodology is used to shed light on how specific vehicle/engine design parameter selections impact control system design. In short, the work represents an important first step toward revealing fundamental tradeoffs and systematically treating control-relevant vehicle design.

Rodriguez, Armando A.↗

Aligning Arrays of Lenses and Single-Mode Optical Fibers

A procedure now under development is intended to enable the precise alignment of sheet arrays of microscopic lenses with the end faces of a coherent bundle of as many as 1,000 single-mode optical fibers packed closely in a regular array (see Figure 1). In the original application that prompted this development, the precise assembly of lenses and optical fibers serves as a single-mode spatial filter for a visible-light nulling interferometer. The precision of alignment must be sufficient to limit any remaining wavefront error to a root-mean-square value of less than 1/10 of a wavelength of light. This wavefront-error limit translates to requirements to (1) ensure uniformity of both the lens and fiber arrays, (2) ensure that the lateral distance from the central axis of each lens and the corresponding optical fiber is no more than a fraction of a micron, (3) angularly align the lens-sheet planes and the fiber-bundle end faces to within a few arc seconds, and (4) axially align the lenses and the fiber-bundle end faces to within tens of microns of the focal distance. Figure 2 depicts the apparatus used in the alignment procedure. The beam of light from a Zygo (or equivalent) interferometer is first compressed by a ratio of 20:1 so that upon its return to the interferometer, the beam will be magnified enough to enable measurement of wavefront quality. The apparatus includes relay lenses that enable imaging of the arrays of microscopic lenses in a charge-coupled-device (CCD) camera that is part of the interferometer. One of the arrays of microscopic lenses is mounted on a 6-axis stage, in proximity to the front face of the bundle of optical fibers. The bundle is mounted on a separate stage. A mirror is attached to the back face of the bundle of optical fibers for retroreflection of light. When a microscopic lens and a fiber are aligned with each other, the affected portion of the light is reflected back by the mirror, recollimated by the microscopic lens, transmitted through the relay lenses and the beam compressor/expander, then split so that half goes to a detector and half to the interferometer. The output of the detector is used as a feedback control signal for the six-axis stage to effect alignment.

Liu, Duncan↗

Tension–Compression Asymmetry Improved by Cold Extrusion in Pure Magnesium

In this paper, cold extrusion was successfully used to fabricate the fine-grained pure Mg bar with average grain size of 2.5 μm. The microstructure, texture and mechanical properties were evaluated by electron backscattering diffraction and mechanical test. The results showed that the corresponding yield strengths for as-extruded fine-grained pure Mg were 130.8 MPa in tension and 125.6 MPa in compression, leading to a greatly improved yield asymmetry ratio. The improvement in tension–compression asymmetry is mainly due to grain refinement which favors the suppression of deformation twinning in compression and promotion of multi-deformation modes both in tension and compression at small strains.

36 MATERIALS SCIENCE↗

First-principles equation of state and shock compression predictions of warm dense hydrocarbons

We use path integral Monte Carlo and density functional molecular dynamics to construct a coherent set of equations of state (EOS) for a series of hydrocarbon materials with various C:H ratios (2:1, 1:1, 2:3, 1:2, and 1:4) over the range of 0.07–22.4gcm –3 and 6.7 × 10 3 – 1.29 × 10 8 K. The shock Hugoniot curve derived for each material displays a single compression maximum corresponding to K-shell ionization. For C:H = 1:1, the compression maximum occurs at 4.7-fold of the initial density and we show radiation effects significantly increase the shock compression ratio above 2 Gbar, surpassing relativistic effects. The single-peaked structure of the Hugoniot curves contrasts with previous work on higher-Z plasmas, which exhibit a two-peak structure corresponding to both K- and L-shell ionization. Analysis of the electronic density of states reveals that the change in Hugoniot structure is due to merging of the L-shell eigenstates in carbon, while they remain distinct for higher-Z elements. Lastly, we show that the isobaric-isothermal linear mixing rule for carbon and hydrogen EOS is a reasonable approximation with errors better than 1% for stellar-core conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

An Experimental Parametric Study of Geometric, Reynolds Number, and Ratio of Specific Heats Effects in Three-Dimensional Sidewall Compression Scramjet Inlets at Mach 6

Since mission profiles for airbreathing hypersonic vehicles such as the National Aero-Space Plane include single-stage-to-orbit requirements, real gas effects may become important with respect to engine performance. The effects of the decrease in the ratio of specific heats have been investigated in generic three-dimensional sidewall compression scramjet inlets with leading-edge sweep angles of 30 and 70 degrees. The effects of a decrease in ratio of specific heats were seen by comparing data from two facilities in two test gases: in the Langley Mach 6 CF4 Tunnel in tetrafluoromethane (where gamma=1.22) and in the Langley 15-Inch Mach 6 Air Tunnel in perfect gas air (where gamma=1.4). In addition to the simulated real gas effects, the parametric effects of cowl position, contraction ratio, leading-edge sweep, and Reynolds number were investigated in the 15-Inch Mach 6 Air Tunnel. The models were instrumented with a total of 45 static pressure orifices distributed on the sidewalls and baseplate. Surface streamline patterns were examined via oil flow, and schlieren videos were made of the external flow field. The results of these tests have significant implications to ground based testing of inlets in facilities which do not operate at flight enthalpies.

Holland, Scott D.↗

Multi-stage heat release of multi-component fuels: Insights and implications for advanced engine operation

Multi-stage heat release (MSHR) is a unique phenomenon typically seen in lean/diluted and low- to intermediate-temperature combustion. Despite its relevance to advanced engine operation, the MSHR of multi-component fuels has barely been quantified. This study aims to characterize the MSHR of multi-component fuels in a rapid compression machine (RCM) at conditions representative of advanced combustion engines. New experimental data are first reported in the RCM at an equivalence ratio of 0.4, pressure of 60 bar and temperatures from 702 to 795 K for a research grade, multi-component gasoline surrogate, termed PACE-20. Here, experiments confirm the existence of MSHR for PACE-20 at all temperatures, and reveal the strong inhibiting effect of temperature on MSHR, where increasing temperature inhibits MSHR by suppressing first stage heat release and promoting second and third stage heat release. A detailed chemical kinetic model is also adopted to model the experiments, with good agreement observed. The response of MSHR characteristics to changes in different engine operating parameters (i.e., temperature, pressure, equivalence ratio and CO 2 dilution level) and fuel compositions (i.e., mole fraction of n-pentane, n-heptane, isooctane, cyclopentane, 1-hexene, ethanol and aromatics in PACE-20) is further evaluated via statistical analysis coupling quasi-random sampling, extensive computer experiments and high-dimensional model representation. The change in MSHR is characterized through 8 quantities of interest (QOIs), i.e., duration and extent of each heat release stage, and their standard deviations. The analysis highlights the dependence of the QOIs on the individual parameters as well as their interplays, with temperature exhibiting the strongest impact among all parameters. Furthermore, it is demonstrated that if MSHR is to be facilitated and combustion phasing is to be extended to enable engine operation at higher compression ratios, it is recommended to operate the engine at low intake temperatures, boosted intake pressures and high CO 2 dilutions (i.e., high EGR levels) with gasoline fuels containing more n-pentane and less aromatics.

42 ENGINEERING↗

Pressure dependence of Poisson’s ratio of glassy Baltic amber studied by Brillouin scattering spectroscopy

Amber is a typical natural glass with very long aging time. Elastic properties of amber at high pressures have been studied using Brillouin scattering and a diamond anvil cell. Both longitudinal and transverse acoustic modes have been observed up to 12 GPa. The pressure dependences of longitudinal, shear, Young’s, and bulk moduli, compressibility, and Poisson’s ratio were determined. The longitudinal, shear, Young’s, bulk moduli show the remarkable increase, and compressibility shows a marked decrease with increasing pressure. However, it is found that the pressure dependence of Poisson’s ratio is very small. The mechanism of this small pressure dependence was discussed. Finally, the Cauchy type relation between longitudinal and shear moduli was examined. Its coefficients show the deviation from the Cauchy relation owing to the coexistence of different intermolecular interactions in amber.

07 ISOTOPE AND RADIATION SOURCES↗

Non-linear properties of metallic cellular materials with a negative Poisson's ratio

Negative Poisson's ratio copper foam was prepared and characterized experimentally. The transformation into re-entrant foam was accomplished by applying sequential permanent compressions above the yield point to achieve a triaxial compression. The Poisson's ratio of the re-entrant foam depended on strain and attained a relative minimum at strains near zero. Poisson's ratio as small as -0.8 was achieved. The strain dependence of properties occurred over a narrower range of strain than in the polymer foams studied earlier. Annealing of the foam resulted in a slightly greater magnitude of negative Poisson's ratio and greater toughness at the expense of a decrease in the Young's modulus.

Choi, J. B.↗

Study by the Prandtl-Glauert method of compressibility effects and critical Mach number for ellipsoids of various aspect ratios and thickness ratios

By using the Prandtl-Glauert method that is valid for three-dimensional flow problems, the value of the maximum incremental velocity for compressible flow about thin ellipsoids at zero angle of attack is calculated as a function of the Mach number for various aspect ratios and thickness ratios. The critical Mach numbers of the various ellipsoids are also determined. The results indicate an increase in critical Mach number with decrease in aspect ratio which is large enough to explain experimental results on low-aspect-ratio wings at zero lift.

Hess, Robert V↗

Anisotropies of the Magnetic Field Fluctuations at Kinetic Scales in the Solar Wind: Cluster Observations

We present the first statistical study of the anisotropy of the magnetic field turbulence in the solar wind between 1 and 200 Hz, i.e., from proton to sub-electron scales. We consider 93 ten-minute intervals of the Cluster/STAFF measurements. We find that the fluctuations δB{sub ⊥}{sup 2} are not gyrotropic at a given frequency f, a property already observed at larger scales (∥/⊥ means parallel/perpendicular to the average magnetic B{sub 0}). This non-gyrotropy gives indications of the angular distribution of the wave vectors k: at f< 10 Hz, we find that k{sub ⊥}≫k{sub ∥}, mainly in the fast wind; at f > 10 Hz, fluctuations with a non-negligible k {sub ∥} are also present. We then consider the anisotropy ratio δB{sub ∥}{sup 2}/δB{sub ⊥}{sup 2}, which is a measure of the magnetic compressibility of the fluctuations. This ratio, always smaller than 1, increases with f. It reaches a value showing that the fluctuations are more or less isotropic at electron scales, for f⩾50 Hz. From 1 to 15–20 Hz, there is a strong correlation between the observed compressibility and the one expected for the kinetic Alfvén waves (KAWs), which only depends on the total plasma β. For f>15--20 Hz, the observed compressibility is larger than expected for KAWs, and it is stronger in the slow wind: this could be an indication of the presence of a slow-ion acoustic mode of fluctuations, which is more compressive and is favored by the larger values of the electron to proton temperature ratio generally observed in the slow wind.

79 ASTRONOMY AND ASTROPHYSICS↗

New theoretical models and ratio imaging techniques associated with the NASA earth resources spectral information system

Four independent investigations are reported; in general these are concerned with improving and utilizing the correlation between the physical properties of natural materials as evidenced in laboratory spectra and spectral data collected by multispectral scanners. In one investigation, two theoretical models were devised that permit the calculation of spectral emittance spectra for rock and mineral surfaces of various particle sizes. The simpler of the two models can be used to qualitatively predict the effect of texture on the spectral emittance of rocks and minerals; it is also potentially useful as an aid in predicting the identification of natural atmospheric aerosol constituents. The second investigation determined, via an infrared ratio imaging technique, the best pair of infrared filters for silicate rock-type discrimination. In a third investigation, laboratory spectra of natural materials were compressed into 11-digit ratio codes for use in feature selection, in searches for false alarm candidates, and eventually for use as training sets in completely automatic data processors. In the fourth investigation, general outlines of a ratio preprocessor and an automatic recognition map processor are developed for on-board data processing in the space shuttle era.

Vincent, R. K.↗

Compressive Deformation Behavior of Open-Cell Cu-Zn-Al Alloy Foam Made Through P/M Route Using Mechanically Alloyed Powder

Cu-Zn-Al foams of varying porosity fractions using mechanical alloyed powder have been made through powder metallurgy route. Here, NH{sub 4} (HCO{sub 3}) was used as a space holder. Mechanically alloyed Cu-Zn-Al is made using a planetary ball mill taking the ratio of Cu/Zn/Al = 70:25:5 (by weight ratio). The ball/powder ratios were varied in the four ranges 10:1, 15:1, 20:1, and 25:1. Green compacts of milled powder and space holder samples were sintered at three stages at three different temperatures 350, 550, and 850 °C for 1 h at each stage. The crystalline size and particle size as a function of ball/powder ratios were examined. The compressive deformation responses of foams are varied with relative density and the ball/powder ratio. The plateau stress and energy absorption of these foams increase with an increase in relative density but decreases with increase in ball/powder ratio, even though crystalline size decreases. This has further been explained on the basis of particle morphology as a function of ball/powder ratio.

36 MATERIALS SCIENCE↗

High-Temperature Interactions Between Vanadium-Titanium Magnetite Carbon Composite Hot Briquettes and Pellets Under Simulated Blast Furnace Conditions

The high-temperature interactions between vanadium-titanium magnetite carbon composite hot briquettes (VTM-CCBs) and pellets were systematically investigated under simulated blast furnace conditions with respect to the reduction behavior, softening–melting–dripping characteristics, gas permeability, and Ti(C, N) precipitation mechanisms. The results showed that VTM-CCB charging can promote the reduction of the pellet in the packed bed and decrease the compressive strength of the pellet after reduction. The compressive strength of the VTM-CCB after reduction decreased with increasing temperature when the FC/O ratio (the ratio of the fixed carbon mol(C) in coal to the reducible oxygen mol(O) in iron oxides) was higher than 1.0. With an FC/O ratio lower than 1.0, the compressive strength of the VTM-CCB initially decreased and then increased. The FC/O ratio has a significant influence on the softening–melting interaction mechanism between the VTM-CCB and the pellet. With an FC/O ratio of 0.8, the bonding layer at the interface between the pellet and the VTM-CCB (consisting of molten fayalitic slag) can promote the softening process, thereby decreasing the softening start and end temperatures. By increasing the FC/O ratio to 1.4, a dense metallic iron shell with relatively high strength formed at the interface and restricted the collapse of the packed bed, thereby increasing the softening start and end temperatures and ensuring the transport of the reduction gas through the packed bed. The melting point of the primary slag phase increased with increasing FC/O ratio due to a decrease in the FeO content, which resulted in an increase in the melting start temperature from 1273 °C to 1294 °C (1546 K to 1567 K). The gas permeability in the cohesive zone increased with an increasing FC/O ratio of the VTM-CCB due to a combination of the skeletal role performed by the residual VTM-CCB and the decrease in the liquid slag proportion. In addition, as the FC/O ratio increased to 1.4, unconsumed carbon promoted the precipitation of Ti(C, N) at the slag–carbon and slag–metal interfaces, which resulted in a substantial increase in the dripping temperature and deterioration of the dripping behavior of the packed bed. Therefore, to suppress the precipitation of Ti(C, N) and improve the dripping behavior of the packed bed, the FC/O ratio of the charged VTM-CCB should be controlled within an appropriate range.

36 MATERIALS SCIENCE↗

Influence of CaO/FeO ratio on the formation mechanism and properties of alkali-activated Fe-rich slags

Highlights: • Effect of the CaO/FeO molar ratio in alkali-activated Fe-rich slags is unraveled. • Low CaO/FeO molar ratios enhance the early kinetics and compressive strength. • Reaction extent and strength further increase with higher CaO/FeO ratio after 7 days. • Fe{sup 2+}-trioctahedral layers of the binder are hydroxylated and in a silicate phase. • The final strength is determined by the influence of Ca on the reaction products. In the search for CO{sub 2} mitigating cement technologies, alkali-activated Fe-rich slags present a possible alternative. The influence of the chemical composition of the synthetic Fe-silicate slag on the reaction mechanisms is assessed by varying the CaO/FeO molar ratio. The alkali-activated Fe-rich slags consist of trioctahedral layers that are shown to be hydroxylated and in contact with silicates, in a similar way to phyllosilicate minerals. The formation of this phyllosilicate-like structure is hindered during the first days for samples with high CaO/FeO ratios, because of the partial incorporation of Ca in the trioctahedral layers. At later ages, the samples with higher CaO/FeO ratios gain in reaction extent, to exceed the reaction extent of low CaO/FeO ratios at 28 days and beyond. The increase in compressive strength is even more pronounced than the effect on the reaction extent, which underlines the importance of Ca on the inherent strength of the binding phases.

36 MATERIALS SCIENCE↗

Poisson's Ratio of a Hyperelastic Foam Under Quasi-static and Dynamic Loading

Poisson's ratio is a material constant representing compressibility of material volume. However, when soft, hyperelastic materials such as silicone foam are subjected to large deformation into densification, the Poisson's ratio may rather significantly change, which warrants careful consideration in modeling and simulation of impact/shock mitigation scenarios where foams are used as isolators. The evolution of Poisson's ratio of silicone foam materials has not yet been characterized, particularly under dynamic loading. In this study, radial and axial measurements of specimen strain are conducted simultaneously during quasi-static and dynamic compression tests to determine the Poisson's ratio of silicone foam. The Poisson's ratio of silicone foam exhibited a transition from compressible to nearly incompressible at a threshold strain that coincided with the onset of densification in the material. Poisson's ratio as a function of engineering strain was different at quasi-static and dynamic rates. Here, the Poisson's ratio behavior is presented and can be used to improve constitutive modeling of silicone foams subjected to a broad range of mechanical loading.

36 MATERIALS SCIENCE↗

Exploring the Effects of Piston Bowl Geometry and Injector Included Angle on Dual-Fuel and Single-Fuel RCCI

Abstract Reactivity control compression ignition (RCCI) is a low-temperature combustion technique that has been proposed to meet the current demand for high thermal efficiency and low engine-out emissions. However, its requirement of two separate fuel systems (i.e., a low-reactivity fuel system and a high-reactivity fuel system) has been one of its major challenges in the last decade. This leads to the single-fuel RCCI concept, where the secondary fuel (reformates of diesel) is generated from the primary fuel (diesel) through catalytic partial oxidation reformation. Following the in-depth analysis of the reformate fuel (reformates of diesel) and its benefit as the low-reactivity fuel with diesel, the effects of the start of injection (SOI) timing of diesel and the energy-based blend ratio were also studied in detail. In this study, the effects of piston profile and the injector included angles were experimentally examined using both conventional fuel pairs (gasoline—diesel and natural gas—diesel) and reformate RCCI. A validated computational fluid dynamics (CFD) model was also used for a better understanding of the experimental trends. Comparing a reentrant bowl piston with a shallow bowl piston at a constant compression ratio and SOI, the latter showed better thermal efficiency, regardless of the fuel combination, due to its 10% lower surface area for the heat transfer. Comparing the 150-degree included angle and 60-degree included angle on the shallow bowl piston, the latter showed better combustion efficiency, regardless of the fuel combination, due to its earlier combustion phasing (at constant SOI timing). The effect was particularly prominent on reformate RCCI because of its incredibly high diluent concentration, which retards the combustion further for the 150-deg injector. Later, using convergecfd, seven different injector included angles were studied at a constant SOI. With the change in injector included angle, the region of the cylinder targeted by the fuel spray varies significantly, and it was found to have a significant impact on the combustion efficiency and the engine-out emissions. As the injector included angle changed from 60-deg to 150-deg, the combustion efficiency increased by 15% and the CO, NOx, and HC emissions decreased by 96%, 70%, and 86%, respectively.

Engineering↗

Low-frequency waves in a high-beta collisionless plasma Polarization, compressibility and helicity

This paper considers the linear theory of waves near and below the ion cyclotron frequency in an isothermal electron-ion Vlasov plasma which is isotropic, homogeneous and magnetized. Numerical solutions of the full dispersion equation for the magnetosonic/whistler and Alfven/ion cyclotron modes at beta(i) = 1.0 are presented, and the polarizations, compressibilities, helicities, ion Alfven ratios and ion cross-helicities are exhibited and compared. At sufficiently large beta(i) and theta, the angle of propagation with respect to the magnetic field, the real part of the polarization of the Alfven/ion cyclotron wave changes sign, so that, for such parameters, this mode is no longer left-hand polarized. The Alfven/ion cyclotron mode becomes more compressive as the wavenumber increases, whereas the magnetosonic/whistler becomes more compressive with increasing theta.

Gary, S. P.↗