Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Axial flow compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27

The response of an axial compressor to unsteady disturbances

The disturbances of flow in a uniform duct are examined, taking into account a disturbance which is sinusoidal in time. The equations of motion for a plane disturbance with blade forces represented by body forces are considered along with the stage configuration of the compressor and the temperature rise for two-dimensional flow through the stage. An investigation is conducted for the case in which the disturbances are restricted to small amplitudes about the design operating condition for all points within the compressor. The three independent solutions of the disturbance equations obtained for the system of compressor and associated inlet and exit ducts can be used with three arbitrary constants to satisfy three external conditions.

Rannie, W. D.↗

Task II: Three-dimensional Rotating Stall Inception and Effects of Rotating Tip Clearance Asymmetry in Axial Compressors

The effects of two types of flow non-uniformity on stall inception behavior were assessed with linearized stability analyses of two compressor flow models. Response to rotating tip clearance asymmetries induced by a whirling rotor shaft or rotor height variations were investigated with a two-dimensional flow model. A 3-D compressor model was also developed to study the stability of both full-span and part-span rotating stall modes in annular geometries with radial flow variations. The studies focussed on (1) understanding what compressor designs were sensitive to these types of circumferential and spanwise flow non-uniformities, and (2) situations where 2-D stability theories were inadequate because of 3-D flow effects. Rotating tip clearance non-uniformity caused the greatest performance loss for shafts whirling at the rotating stall frequency. A whirling shaft displacement of 1 percent chord caused the stalling mass flow to rise by as much as 10 percent and the peak pressure rise to decrease by 6 percent. These changes were an order of magnitude larger than for equivalent-sized stationary or rotor-locked clearance asymmetries. Spanwise flow non-uniformity always destabilized the compressor, so that 2-D models over-predicted that stall margin compared to 3-D theory. The difference increased for compressors with larger spanwise variations of characteristic slope and reduced characteristic curvature near the peak. Differences between 2-D and 3-D stall point predictions were generally unacceptable (2 - 4 percent of flow coefficient) for single-stage configurations, but were less than 1 percent for multistage compressors. 2-D analyses predicted the wrong stall mode for specific cases of radial inlet flow distortion, mismatching and annulus area contraction, where higher-order radial modes led to stall. The stability behavior of flows with circumferential or radial non-uniformity was unified through a single stability criterion. The stall point for both cases was set by the integral around the annulus of the pressure rise characteristic slope, weighted by the amplitude of the mode shape. For the case of steady circumferential variations, this criterion reduced to the integrated mean slope (IMS) condition associated with steady inlet distortions. The rotating tip clearance asymmetry model was also used to demonstrate the feasibility of actively controlling the shaft position to suppress rotating stall. In axisymmetric mean flow, this method only stabilized the first harmonic mode, increasing the operating range until surge or higher harmonic modes became unstable.

Suder, Kenneth↗

System Study for Axial Vane Engine Technology

The purpose of this engine feasibility study was to determine the benefits that can be achieved by incorporating positive displacement axial vane compression and expansion stages into high bypass turbofan engines. These positive-displacement stages would replace some or all of the conventional compressor and turbine stages in the turbine engine, but not the fan. The study considered combustion occurring internal to an axial vane component (i.e., Diesel engine replacing the standard turbine engine combustor, burner, and turbine); and external continuous flow combustion with an axial vane compressor and an axial vane turbine replacing conventional compressor and turbine systems.

Badley, Patrick R.↗

A viscous-inviscid interactive compressor calculations

A viscous-inviscid interactive procedure for subsonic flow is developed and applied to an axial compressor stage. Calculations are carried out on a two-dimensional blade-to-blade region of constant radius assumed to occupy a mid-span location. Hub and tip effects are neglected. The Euler equations are solved by MacCormack's method, a viscous marching procedure is used in the boundary layers and wake, and an iterative interaction scheme is constructed that matches them in a way that incorporates information related to momentum and enthalpy thicknesses as well as the displacement thickness. The calculations are quasi-three-dimensional in the sense that the boundary layer and wake solutions allow for the presence of spanwise (radial) velocities.

Johnston, W.↗

A viscous-inviscid interactive compressor calculation

A viscous-inviscid interactive procedure for subsonic flow is developed and applied to an axial compressor stage. Calculations are carried out on a two-dimensional blade-to-blade region of constant radius assumed to occupy a mid-span location. Hub and tip effects are neglected. The Euler Equations are solved by MacCormack's method, a viscous marching procedure is used in the boundary layers and wake, and an iterative interaction scheme is constructed that matches them in a way that incorporates information related to momentum and enthalpy thicknesses as well as the displacement thickness. The calculations are quasi-three-dimensional in the sense that the boundary layer and wake solutions allow for the presence of spanwise (radial) velocities.

Johnston, W. A.↗

Development and Application of Advanced Measurement Techniques for Characterizing and Controlling Flow Instabilities in Axial Turbomachines

This report summarizes the recent progress in a project aimed at characterizing the flow structure, instabilities, and turbulence in axial compressors, and also on the utilization of casing grooves for delaying the onset of stall without performance degradation at high flow rates. Progress had been hindered by the COVID-19 laboratory closures and restrictions on the number of people that could be present in the laboratory during Fiscal Year 2020. Once the restrictions were lifted, the tasks described in this report were completed.

compressor↗

Secondary vorticity in axial compressor blade rows

A theoretical investigation of secondary flow in compressor blade rows is presented. Formulas for calculating secondary flows in annular cascade blade passages are derived. The influence of the relative rotation vector on secondary velocity perturbations, using recent developments in shear-flow theory, is examined. A method of calculating the flow through successive blade rows is given and a comparison is made with experimental results.

Dixon, S. L.↗

Low-turbulence high-speed wind tunnel for the determination of cascade shock losses

A low turbulence high-speed wind tunnel, using anti-turbulence screening and a 100:1 contraction ratio, has been found suitable for high-speed smoke flow visualization. The location and strength of normal, oblique, and curved shock waves generated by transonic or supersonic wind tunnel flow over airfoils or through axial compressor cascades is determined by combined shadowgraph and smokelines visualization techniques without the interference effects caused by intrusive probes. The Reynolds number based on chord varied between 50,000 and 1,000,000. Preliminary results are compared with the relevant theory and data gathered using a total pressure probe.

Slovisky, J. A.↗

Automated design of controlled diffusion blades

A numerical automation procedure was developed to be used in conjunction with an inverse hodograph method for the design of controlled diffusion blades. With this procedure a cascade of airfoils with a prescribed solidity, inlet Mach No., inlet air flow angle and air flow turning can be produced automatically. The trailing edge thickness of the airfoil, an important quantity in inverse methods, is also prescribed. The automation procedure consists of a multi-dimensional Newton iteration in which the objective design conditions are achieved by acting on the hodograph input parameters of the underlying inverse code. The method, although more general in scope, is applied to the design of axial flow turbomachinery blade sections, both compressors and turbines. A collaborative effort with U.S. Engine Companies to identify designs of interest to the industry will be described.

Sanz, Jose M.↗

Compressor Study to Meet Large Civil Tilt Rotor Engine Requirements

A vehicle concept study has been made to meet the requirements of the Large Civil Tilt Rotorcraft vehicle mission. A vehicle concept was determined, and a notional turboshaft engine system study was conducted. The engine study defined requirements for the major engine components, including the compressor. The compressor design-point goal was to deliver a pressure ratio of 31:1 at an inlet weight flow of 28.4 lbm/sec. To perform a conceptual design of two potential compressor configurations to meet the design requirement, a mean-line compressor flow analysis and design code were used. The first configuration is an eight-stage axial compressor. Some challenges of the all-axial compressor are the small blade spans of the rear-block stages being 0.28 in., resulting in the last-stage blade tip clearance-to-span ratio of 2.4%. The second configuration is a seven-stage axial compressor, with a centrifugal stage having a 0.28-in. impeller-exit blade span. The compressors conceptual designs helped estimate the flow path dimensions, rotor leading and trailing edge blade angles, flow conditions, and velocity triangles for each stage.

Veres, Joseph P.↗

Compressor Study to Meet Large Civil Tilt Rotor Engine Requirements

A vehicle concept study has been made to meet the requirements of the Large Civil Tilt Rotorcraft vehicle mission. A vehicle concept was determined, and a notional turboshaft engine system study was conducted. The engine study defined requirements for the major engine components, including the compressor. The compressor design-point goal was to deliver a pressure ratio of 31:1 at an inlet weight flow of 28.4 lbm/sec. To perform a conceptual design of two potential compressor configurations to meet the design requirement, a mean-line compressor flow analysis and design code were used. The first configuration is an eight-stage axial compressor. Some challenges of the all-axial compressor are the small blade spans of the rear-block stages being 0.28 in., resulting in the last-stage blade tip clearance-to-span ratio of 2.4 percent. The second configuration is a seven-stage axial compressor, with a centrifugal stage having a 0.28-in. impeller-exit blade span. The compressors conceptual designs helped estimate the flow path dimensions, rotor leading and trailing edge blade angles, flow conditions, and velocity triangles for each stage.

Veres, Joseph P.↗

Inlet flow distortion in turbomachinery

A single stage axial compressor with distorted inflow is studied. The inflow distortion occurs far upstream and may be a distortion in stagnation temperature, stagnation pressure or both. The blade rows are modeled as semi-actuator disks. Losses, quasi-steady deviation angles, and reference incidence correlations are included in the analysis. Both subsonic and transonic relative Mach numbers are considered. A parameter study is made to determine the influence of such variables as Mach number and swirl angle on the attenuation of the distortion.

Seidel, B. S.↗

Axial Compressor Design and Analysis

Program yields blade configurations and aerodynamic flow fields. Program consists of three sections -- two blade design sections and aerodynamic section Program structured that one section used alone, or aerodynamic section used in conjunction with either or both of blading sections. Program written in FORTRAN IV.

William, J. G.↗

Interactive-Boundary-Layer Computations For Oscillating Airfoil

Interactive-boundary-layer method developed for computations of steady flow, extended under assumption of quasi-steady flow, to computations of evolution of two-dimensional flow about oscillating airfoil under light-dynamic-stall conditions. Represents advance toward ability to compute unsteady flows at even greater angles of attack with solutions of equations normally used for description of boundary-layer flows on airfoils prior to stall. Important in practical studies of flow on blades of helicopter rotors, axial compressors, and turbines.

Carr, L. W.↗

Effect of Compressor-outlet Bleedoff on Turbojet-engine Performance

An investigation was conducted in the NACA Lewis altitude wind tunnel to determine the effect of compressor-outlet bleedoff on the performance of an axial-flow turbojet engine equipped with a variable-area exhaust nozzle. Results presented indicate the effect of compressor-outlet bleedoff on performance at altitudes of 25,000 and 40,000 feet and a flight Mach number of 0.53. Variation of performance with bleedoff flow is indicated for operation with fixed- and variable-area exhaust nozzles. Temperature and pressure losses through the bleedoff ducting system are also discussed.

TURBINES, GAS - BLEED-OFF↗

The Influence of the Diameter Ratio on the Characteristics Diagram of the Axial Compressor

With the further development of axial blowers into highly loaded flow machines, the influence of the diameter ratio upon air output and efficiency gains in significance. Clarification of this matter is important for single-stage axial compressors, and is of still greater importance for multistage ones, and particularly for aircraft power plants. Tests with a single-stage axial blower gave a decrease in the attainable maximum pressure coefficient and optimum efficiency as the diameter ratio increased. The decrease must be ascribed chiefly to the guide surface of the hub and housing between the blades increasing with the diameter ratio.

Eckert, B.↗