Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Axial Staging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Two-stage fan. 3: Data and performance with rotor tip casing treatment, uniform and distorted inlet flows

A two stage fan with a 1st-stage rotor design tip speed of 1450 ft/sec, a design pressure ratio of 2.8, and corrected flow of 184.2 lbm/sec was tested with axial skewed slots in the casings over the tips of both rotors. The variable stagger stators were set in the nominal positions. Casing treatment improved stall margin by nine percentage points at 70 percent speed but decreased stall margin, efficiency, and flow by small amounts at design speed. Treatment improved first stage performance at low speed only and decreased second stage performance at all operating conditions. Casing treatment did not affect the stall line with tip radially distorted flow but improved stall margin with circumferentially distorted flow. Casing treatment increased the attenuation for both types of inlet flow distortion.

Burger, G. D.↗
NASA NTRS1978

Pollution Reduction Technology Program for Small Jet Aircraft Engines, Phase 2

A series of iterative combustor pressure rig tests were conducted on two combustor concepts applied to the AiResearch TFE731-2 turbofan engine combustion system for the purpose of optimizing combustor performance and operating characteristics consistant with low emissions. The two concepts were an axial air-assisted airblast fuel injection configuration with variable-geometry air swirlers and a staged premix/prevaporization configuration. The iterative rig testing and modification sequence on both concepts was intended to provide operational compatibility with the engine and determine one concept for further evaluation in a TFE731-2 engine.

Bruce, T. W.↗
NASA NTRS1986

Development of an explicit multigrid algorithm for quasi-three-dimensional viscous flows in turbomachinery

A rapid quasi three-dimensional analysis was developed for blade-to-blade flows in turbomachinery. The analysis solves the unsteady Euler or thin layer Navier-Stokes equations in a body-fitted coordinate system. It accounts for the effects of rotation, radius change, and stream-surface thickness. The Baldwin-Lomax eddy-viscosity model is used for turbulent flows. The equations which are solved b a two-stage Runge-Kutta scheme made efficient by use of vectorization, a variable time-step, and a flux-based multigrid scheme, are described. A stability analysis is presented for the two-stage. Results for a flat-plate model problem show the applicability of the method to axial, radial, and rotating geometries. Results for a centrifugal impeller and a radial diffuser show that the quasi three-dimensional viscous analysis can be a practical design tool.

Chima, R. V.↗
NASA NTRS2014

Analysis of Dual Rotating Rake Data from the NASA Glenn Advanced Noise Control Fan Duct with Artificial Sources

The Rotating Rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. Initially, the mode amplitudes and phases were quantified from a single rake measurement at one axial location. To directly measure the modes propagating in both directions within a duct, a second rake was mounted to the rotating system with an offset in both the axial and the azimuthal directions. The rotating rake data analysis technique was then extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode levels at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode amplitudes for the modes propagating in both directions within the duct. Validation experiments have been conducted using artificial acoustic sources. Results are shown for the measurement of the standing waves in the duct from sound generated by one and two acoustic sources that are separated into the component modes propagating in both directions within the duct. Measured reflection coefficients from the open end of the duct are compared to analytical predictions.

Noise↗
NASA NTRSDate not supplied

The Effect of Anode Configuration on the Plasma Plume of a 25-A class Hollow Cathode

The effect of anode configuration on the plasma plume properties of a 25-A class hollow cathode are experimentally characterized. At a nominal operating condition of 20.8 A and 14.7 sccm of xenon, the cathode was operated with two axially-segmented anodes of different diameters at varying distance from the cathode. A fast, reciprocating motion stage was used to rapidly insert an ion saturation probe and an emissive probe on cathode centerline, and from those measurements, spatial profiles of plasma density, plasma potential, and electron temperature were calculated. For both anode diameters, maximum plasma potential and electron temperature increased with increasing anode distance. However, the 64-mm diameter anode was found to be significantly more sensitive to position, with measurements indicating that parameters changed continuously with position instead of an instantaneous mode change at a certain critical distance. The 254-mm diameter, in contrast, showed much more similar plasma property profiles across the range of anode positions tested and much smaller changes per unit increase in distance. These results are discussed in the context of assessing anode design for component-level cathode tests.

Space propulsion↗
NASA NTRSDate not supplied

The Effect of Anode Configuration on the Plasma Plume of a 25-A class Hollow Cathode

The effect of anode configuration on the plasma plume properties of a 25-A class hollow cathode are experimentally characterized. At a nominal operating condition of 20.8 A and 14.7 sccm of xenon, the cathode was operated with two axially-segmented anodes of different diameters at varying distance from the cathode. A fast, reciprocating motion stage was used to rapidly insert an ion saturation probe and an emissive probe on cathode centerline, and from those measurements, spatial profiles of plasma density, plasma potential, and electron temperature were calculated. For both anode diameters, maximum plasma potential and electron temperature increased with increasing anode distance. However, the 64-mm diameter anode was found to be significantly more sensitive to position, with measurements indicating that parameters changed continuously with position instead of an instantaneous mode change at a certain critical distance. The 254-mm diameter, in contrast, showed much more similar plasma property profiles across the range of anode positions tested and much smaller changes per unit increase in distance. These results are discussed in the context of assessing anode design for component-level cathode tests.

space propulsion↗
NASA NTRS1991

Penn State axial flow turbine facility: Performance and nozzle flow field

The objective is to gain a thorough understanding of the flow field in a turbine stage including three-dimensional inviscid and viscid effects, unsteady flow field, rotor-stator interaction effects, unsteady blade pressures, shear stress, and velocity field in rotor passages. The performance of the turbine facility at the design condition is measured and compared with the design distribution. The data on the nozzle vane static pressure and wake characteristics are presented and interpreted. The wakes are found to be highly three-dimensional, with substantial radial inward velocity at most spanwise locations.

Lakshminarayana, B.↗
NASA NTRS1985

Development of an explicit multigrid algorithm for quasi-three-dimensional viscous flows in turbo-machinery

A rapid quasi three-dimensional analysis was developed for blade-to-blade flows in turbomachinery. The analysis solves the unsteady Euler or thin layer Navier-Stokes equations in a body-fitted coordinate system. It accounts for the effects of rotation, radius change, and stream-surface thickness. The Baldwin-Lomax eddy-viscosity model is used for turbulent flows. The equations which are solved by a two-stage Runge-Kutta scheme made efficient by use of vectorization, a variable time-step, and a flux-based multigrid scheme, are described. A stability analysis is presented for the two-stage scheme. Results for a flat-plate model problem show the applicability of the method to axial, radial, and rotating geometries. Results for a centrifugal impeller and a radial diffuser show that the quasi three-dimensional viscous analysis can be a practical design tool.

Chima, R. V.↗
NASA NTRS1959

Analytical Investigation of the Effect of Turbopump Design on Gross-Weight Characteristics of a Hydrogen-Propelled Nuclear Rocket

The effect of turbopump design on rocket gross weight was investigated for a high-pressure bleed-type hydrogen-reactor long-range rocket with a fixed mission. Axial-flow, mixed-flow, and centrifugal pumps driven by single and twin turbines were considered. With an efficiency of 0.7 assumed for all pumps, the lowest rocket gross weights were obtained with an axial-flow or a mixed-flow pump driven by a single turbine of at least eight stages. All turbopump combinations could be used, however, with gross weight varying less than 8 percent for a given payload. Turbopump efficiencies have a significant effect on the ratio of gross weight to payload with the magnitude of the effect determined by the ratio of rocket structural weight to total propellant weight. One point in pump efficiency is worth 0.2 percent in gross weight for a given payload with a structural weight parameter of 0.1 and 0.6 percent with a structural weight parameter of 0.2. Turbine and pump weights are much less significant in terms of gross-to-pay weight ratio than the efficiencies of these components. One point in pump efficiency is equivalent to approximately 13 percent in pump weight, while 1 point in turbine efficiency is equivalent to about 7 percent in turbine weight.

Rohlik, Harold E.↗
NASA NTRS2003

Calculation of Turbine Axial Thrust by Coupled CFD Simulations of the Main Flow Path and Secondary Cavity Flow in an SLI LOX Turbine

Each single reusable Space Launch Initiative (SLI) booster rocket is an engine operating at a record vacuum thrust level of over 730,000 Ibf using LOX and LH2. This thrust is more than 10% greater than that of the Delta IV rocket, resulting in relatively large LOX and LH2 turbopumps. Since the SLI rocket employs a staged combustion cycle the level of pressure is very high (thousands of psia). This high pressure creates many engineering challenges, including the balancing of axial-forces on the turbopumps. One of the main parameters in the calculation of the axial force is the cavity pressure upstream of the turbine disk. The flow in this cavity is very complex. The lack of understanding of this flow environment hinders the accurate prediction of axial thrust. In order to narrow down the uncertainty band around the actual turbine axial force, a coupled, unsteady computational methodology has been developed to simulate the interaction between the turbine main flow path and the cavity flow. The CORSAIR solver, an unsteady three- dimensional Navier-Stokes code for turbomachinery applications, was used to solve for both the main and the secondary flow fields. Turbine axial thrust values are presented in conjunction with the CFD simulation, together with several considerations regarding the turbine instrumentation for axial thrust estimations during test.

Dorney, D. J.↗
NASA NTRS1972

Single-stage experimental evaluation of tandem-airfoil rotor and stator blading for compressors. Part 5: Analysis and design of stages D and E

A conventional and a tandem bladed stage were designed for a comparative experimental evaluation in a 0.8 hub/tip ratio single-stage compressor. Based on a preliminary design study, a radially constant work input distribution was selected for the rotor designs. Velocity diagrams and blade leading and trailing edge angles selected for the conventional rotor and stator were used in the design of the tandem blading. The effects of axial velocity ratio and secondary flow on turning were included in the selection of blade leading and trailing edge angles. Design values of rotor tip velocity and stage pressure ratio were 757 ft/sec and 1.26, respectively.

Brent, J. A.↗
NASA NTRS1982

Embryonic development during chronic acceleration

Experiments carried out on chicken eggs indicate that the embryo is affected during very early development, especially over the first four days, and during hatching. In the first four days, the brain develops as well as the anlage for all other organs. In addition, the heart commences to function and the extraembryonic membranes that compartmentalize the egg contents form. The latter require an appreciable extension and folding of tissue which may be disrupted by the mechanical load. Observations of embryonic abnormalities that occur during chronic acceleration suggest an inhibition of development of the axial skeleton, which is rarely seen otherwise, a general retardation of embryonic growth, and circulatory problems. The final stages of development (after 18 days) involve the uptake of fluids, the transition to aerial respiration, and the reorientation of the embryo into a normal hatching position. At 4 G mortality is very high during this period, with a majority of embryos failing to reorient into the normal hatching position.

Smith, A. H.↗
NASA NTRS1983

Advanced propfan engine characteristics and technology needs

A comparative study is presented for two of the advanced gas turbine engine designs developed in the course of a proprietary research effort for the NASA Advanced Propfan Engine Technology research program. In these engines, a cycle pressure ratio of 32.5:1 and a 2500 F maximum turbine temperature provide fuel efficient operation in the 32,000-ft altitude, Mach 0.72 cruise speed regime stipulated. Both of the engine configurations incorporate three spools, of which the compressors are dual-spool and the power turbines are free. A major design challenge for axial compressors in the 10,000-shp class was the maintenance of adequate blade heights in the later stages.

Anderson, R. D.↗
NASA NTRS1996

Unsteady Blade Row Interaction in a Transonic Turbine

Experimental data from jet-engine tests have indicated that unsteady blade row interaction effects can have a significant impact on the performance of multiple-stage turbines. The magnitude of blade row interaction is a function of both blade-count ratio and axial spacing. In the current research program, numerical simulations have been used to quantify the effects of blade count ratio on the performance of an advanced turbine geometries.

Dorney, Daniel J.↗
NASA NTRS2005

Rocket Engine Nozzle Side Load Transient Analysis Methodology: A Practical Approach

At the sea level, a phenomenon common with all rocket engines, especially for a highly over-expanded nozzle, during ignition and shutdown is that of flow separation as the plume fills and empties the nozzle, Since the flow will be separated randomly. it will generate side loads, i.e. non-axial forces. Since rocket engines are designed to produce axial thrust to power the vehicles, it is not desirable to be excited by non-axial input forcing functions, In the past, several engine failures were attributed to side loads. During the development stage, in order to design/size the rocket engine components and to reduce the risks, the local dynamic environments as well as dynamic interface loads have to be defined. The methodology developed here is the way to determine the peak loads and shock environments for new engine components. In the past it is not feasible to predict the shock environments, e.g. shock response spectra, from one engine to the other, because it is not scaleable. Therefore, the problem has been resolved and the shock environments can be defined in the early stage of new engine development. Additional information is included in the original extended abstract.

Shi, John J.↗
NASA NTRS1954

Experimental Investigation of Stage Performance of J71 Three-stage Turbine

An experimental investigation of the stage performance of the J71 three-stage turbine at design speed and pressure ratio was conducted as part of a program involving research on the design and operational characteristics of high-work-output multistage axial-flow turbines. The investigation indicated that the over-all work output of the turbine based on temperature measurements at design speed and pressure ratio was 95 percent of the design value, with the greatest loss in work output and efficiency occurring in the first stage. Choking in the second-stage stator over most of the pressure ratios investigated prevented the attainment of design first-stage work output and also prevented any increase in work output of the first stage with increasing over-all pressure ratio at design speed. High losses in the first stage were a contributing factor to this choking condition.

Forrette, Obert E↗
NASA NTRS1991

Fluid-structure interaction forces at pump-impeller-shroud surfaces for axial vibration analysis

The axial forces developed on a pump impeller shroud surfaces are analyzed using a bulk-flow model of the leakage path between the impeller and the housing. Shear stresses at the impeller and the housing surfaces are modeled according to Hirs's turbulent lubrication model. The calculated results yield predictions of resonance peaks of the fluid within the annulus formed by the impeller shroud and housing. Numerical results are presented for a double-suction single-stage pump, showing that the direct stiffness of the perturbed impeller shroud forces is negligible; the forces become important only for pumps with very low axial natural frequencies in comparison to the running speed.

Childs, D. W.↗