Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIR FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 487 records · Page 27
All sourcesNASA NTRSDOE OSTI
NASA NTRS1948

Investigation of X24C-2 10-Stage Axial-Flow Compressor. III - Surge Characteristics

Compressor operation at low air flows for a given speed is limited by unstable flow conditions, commonly called surge. An investigation of surge in centrifugal compressors (reference 1) showed that the pulsation of pressures and velocities occurred when the slope of the compressor characteristic curve was positive and that the magnitude and frequency, as well as the incidence of surge, depended on the capacity and resistance of the total system. Although the theory presented in reference 1 is applicable to axial-floe compressors, little experimental information is available on the surge characteristics of the individual stages of axial-flow compressors, or on the variation of the surge characteristics with operating conditions. During the investigation to determine the performance of the X24C-2 compressor (references 2 and 3), instrumentation was added to study the surge characteristics and to determine the effect of speed and inlet pressure on the frequency, amplitude, and phase relation of the pressure pulsations behind each stage.

Buckner, Howard A., Jr.↗
NASA NTRS1987

Inter and intra blade row laser velocimetry studies of gas turbine compressor flows

The use of a two-component LDV to study the flow within gas turbine intrablade passages and air flow through multistage compressor rigs is investigated. The LDV, multistage compressor, and the data acquisition system employed in the experiments are described. The velocity magnitude and air angle as a function of rotor position were mapped; modulations in the multistage compressor data resulted in the application of spectral analysis techniques to identify and characterize the periodic fluctuations. It is noted that the two-component LDV is applicable to the characterization of the aerodynamics of flows.

Williams, M. Carlson↗
NASA NTRS1974

Flow measurement in base cooling air passages of a rotating turbine blade

The operational performance is decribed of a shaft-mounted system for measuring the air mass flow rate in the base cooling passages of a rotating turbine blade. Shaft speeds of 0 to 9000 rpm, air mass flow rates of 0.0035 to 0.039 kg/sec (0.0077 to 0.085 lbm/sec), and blade air temperatures of 300 to 385 K (80 to 233 F) were measured. Comparisons of individual rotating blade flows and corresponding stationary supply orifice flows agreed to within 10 percent.

Liebert, C. H.↗
NASA NTRS1972

Splitting supersonic nozzle flow into separate jets by overexpansion into a multilobed divergent nozzle

Air flowing from a convergent nozzle at pressure ratios greater than 2.5 has been split into eight separate jets by overexpansion of the flow into a divergent, eight-lobed passage. The splitting of the flow is accompanied by a decrease in the nozzle axial centerline Mach number. This in part is due to the radial inflow of secondary air between the lobes toward the nozzle centerline. Each of the smaller jets is partially split after it leaves the end of the divergent lobed section of the nozzle, thus creating a velocity profile having 16 peaks. At a pressure ratio of 3.5 the flow decelerates to Mach 1 in three convergent nozzle throat diameters. Convergent nozzle flow normally requires 12 diameters to reach Mach 1. The nozzle has a sound attenuation of 12 decibels with a thrust loss of 9 percent for the best configuration tested.

Huff, R. G.↗
NASA NTRS1992

Flow field measurement and visualization using projected smoke trails

A new, simple method is described for measuring and visualizing air flows. The method involves projecting a small heated metal pellet through the air at a speed greater than the flow. The pellet burns as it moves through the air and leaves a wake of very fine, visible, metal oxide particles. The position of this visible smoke trail is then photographed at a sequence of times. The displacement of the trail can be used to provide a plot of the normal component of velocity as a function of distance. Examples are given for very low speed thermal convection (less than about 1 m/sec) and low speed flow over airfoils and cylinders (less than about 10 m/sec). Comparisons of the method to pulsed smoke-wire, spark-tracer and laser fluorescence methods, which give similar information, are discussed.

Steinhoff, J. S.↗
NASA NTRS1983

Viscous shock-layer predictions of three-dimensional nonequilibrium flows past the space shuttle at high angle of attack

Computational solutions were obtained for chemically reacting flowfields over the entire windward surface of the Space Shuttle at high angle of attack. The recently developed computational method for the Space Shuttle is capable of treating three dimensional viscous nonequilibrium air flow as well as equilibrium air and perfect gas flows. A general nonorthogonal computational grid system is used to treat the nonaxisymmetric geometry. Boundary conditions take into account noncatalytic wall, equilibrium with noncatalytic wall condition are compared to the fully catalytic wall solutions, the equilibrium air solutions, the perfect gas solutions, and also the Shuttle flight heating and pressure data. The comparisons show good agreement and correlations in most cases.

Kim, M. D.↗
NASA NTRS1984

Liquid-Nitrogen Test for Blocked Tubes

Nondestructive test identifies obstructed tube in array of parallel tubes. Trickle of liquid nitrogen allowed to flow through tube array until array accumulates substantial formation of frost from moisture in air. Flow stopped and warm air introduced into inlet manifold to heat tubes in array. Tubes still frosted after others defrosted identified as obstructed tubes. Applications include inspection of flow systems having parallel legs.

Wagner, W. R.↗
NASA NTRS1979

Internally coated air-cooled gas turbine blading

Ten candidate modified nickel-aluminide coatings were developed using the slip pack process. These coatings contain additives such as silicon, chromium and columbium in a nickel-aluminum coating matrix with directionally solidified MAR-M200 + Hf as the substrate alloy. Following a series of screening tests which included strain tolerance, dynamic oxidation and hot corrosion testing, the Ni-19A1-1Cb (nominal composition) coating was selected for application to the internal passages of four first-stage turbine blades. Process development results indicate that a dry pack process is suitable for internal coating application resulting in 18 percent or less reduction in air flow. Coating uniformity, based on coated air-cooled blades, was within + or - 20 percent. Test results show that the presence of additives (silicon, chromium or columbium) appeared to improve significantly the ductility of the NiA1 matrix. However, the environmental resistance of these modified nickel-aluminides were generally inferior to the simple aluminides.

Hsu, L.↗
NASA NTRS1953

Free-jet Altitude Investigation of a 20-inch Ram-jet Combustor with a Rich Inner Zone of Combustion for Improved Low-temperature-ratio Operation

An investigation of the altitude performance of a 20-inch-diameter high-temperature-ratio ram-jet combustor which had been redesigned to provide good combustor efficiency over a wide range of temperature ratios was conducted at zero angle of attack in a free-jet facility at a Mach number of 3.0. Configurations investigated incorporated a cylindrical control sleeve which confined the injected fuel at low over-all fuel-air ratios to about 40 percent of the engine air flow. This provided an optimum fuel-air mixture over a portion of the flame holder when the over-all fuel-air ratio was about 0.02. The configurations with the control sleeve operated with good combustor efficiency at fuel-air ratios as lean as 0.015, whereas the original engine had a lean blow-out limit at a fuel-air ratio of about 0.03. The control sleeve had little effect upon the high-fuel-air-ratio performance of the engine.

COMBUSTION, RAM-JET ENGINES↗
NASA NTRS1929

Mathematical and experimental investigation of heat control and power increase in air-cooled aircraft engines

In order to understand the numerical relations between the air velocity, temperature of the cylinder walls, heat dissipation, cylinder dimensions and type of construction an experimental plant was installed in the Siemens and Halske laboratory. The experimental cylinder was exposed to the air stream of a wind tunnel. The compression chamber was heated by an electrically heated oil bath kept constantly in motion by a stirrer. The wall temperatures were measured by thermocouples. The air stream was produced a seven-watt blower. The air flowed through a current rectifier (honeycomb), diffuser, air chamber with quieting sieves and a nozzle.

ENGINES - AIR COOLED - POWER INCREASES↗
NASA NTRS1950

Icing Characteristics and Anti-Icing Heat Requirements for Hollow and Ternally Modified Gas-Heated Inlet Guide Vanes

A two-dimensional inlet-guide-vane cascade was investigated to determine the effects of ice formations on the pressure losses across the guide vanes and to evaluate the heated gas flow and temperature required to prevent Icing at various conditions. A gas flow of approximately 0.4 percent of the inlet-air flow was necessary for anti-icing a hollow guide-vane stage at an inlet-gas temperature of 500 F under the following icing conditions: air velocity, 280 miles per hour; water content, 0.9 gram per cubic meter; and Inlet-air static temperature, 00 F. Also presented are the anti-icing gas flows required with modifications of the hollow Internal gas passage, which show heatinput savings greater than 50 percent.

Gray, Vernon H.↗
NASA NTRS1972

Electric discharges in air - Near infrared emission spectrum.

The emission from glow discharges in flowing air has been investigated in the 1- to 5-micron wavelength region with a vacuum spectrometer. Most of the spectral features observed in the pressure range of .5 to 10 torr are identified, including atomic lines of OI, NI, and HI and molecular bands of N2, NO, N2O, CO2, and CO. The spectra are presented as a function of pressure and a table compiled of the atomic lines. Of particular interest are the contrasts between the emission of the air discharge and that of the pure gases, nitrogen and oxygen. In addition, the results of studies of several discharge modes, employing steady voltages and pulsed, provide data on details of the energy flow within the plasma.

Benesch, W. M.↗
NASA NTRS1979

Evaluation of the time dependent surface shear stress in turbulent flows

The time dependent surface shear stress has been evaluated using surface heat transfer measurements. For fully developed turbulent pipe and open channel water flows, and incompressible and compressible turbulent boundary layer air flows the measurements indicate the absolute magnitude of the surface shear stress fluctuations will be greater than two times the mean values. The root-mean-square shear stress fluctuations were of the order of 0.2 to 0.4 times the mean surface shear values. Due to these large surface shear stress fluctuations and the nonlinear relation between heat transfer and shear stress, a special technique has been developed to evaluate the measurements. It was found that the non-linear averaging errors for a hot film-surface shear stress gauge in a fully developed pipe flow was of the order of 10 percent at low velocities. A hot wire-surface shear stress gauge was employed for measurements of turbulent boundary layers in air.

Sandborn, V. A.↗
DOE OSTI2020

Impact to Cooling Airflow from Truck Platooning

We investigate tradeoffs between the airflow strategies related to engine cooling and the aerodynamic-enabled fuel savings created by platooning. By analyzing air temperatures, engine temperatures and cooling air flow at different platoon distances, we show the thermal impact to the engine from truck platooning. Previously, we collected wind and thermal data for numerous heavy-duty truck platoon configurations (gaps ranging from 4 to 87 meters) and reported the significant fuel savings enabled by these configurations. The fuel consumption for all trucks in the platoon were measured using the SAE J1321 gravimetric procedure as well as calibrated J1939 instantaneous fuel rate while travelling at 65 mph and loaded to a gross weight of 65,000 lb. Using thermocouples mounted 1 m ahead of each truck, anemometers at the grill and a grid of under-hood thermocouples as well as J1939 reported engine temperatures, we analyze the impact to critical operating temperatures from different platoon configurations. Results show significant changes in the engine and under-hood air temperatures that correlate with vehicle gap distance and platoon position.

adaptive cruise control (ACC)↗
DOE OSTI2020

Impact to Cooling Airflow from Truck Platooning: Preprint

We investigate tradeoffs between the airflow strategies related to engine cooling and the aerodynamic-enabled fuel savings created by platooning. By analyzing air temperatures, engine temperatures and cooling air flow at different platoon distances, we show the thermal impact to the engine from truck platooning. Previously, we collected wind and thermal data for numerous heavy-duty truck platoon configurations (gaps ranging from 4 to 87 meters) and reported the significant fuel savings enabled by these configurations. The fuel consumption for all trucks in the platoon were measured using the SAE J1321 gravimetric procedure as well as calibrated J1939 instantaneous fuel rate while travelling at 65 mph and loaded to a gross weight of 65,000 lb. Using thermocouples mounted 1 m ahead of each truck, anemometers at the grill and a grid of under-hood thermocouples as well as J1939 reported engine temperatures, we analyze the impact to critical operating temperatures from different platoon configurations. Results show significant changes in the engine and under-hood air temperatures that correlate with vehicle gap distance and platoon position.

47 OTHER INSTRUMENTATION↗
NASA NTRS2007

A Novel Method for Breath Capture Inside a Space Suit

Any non-robotic mission to the Mars surface will need to rely on various life support technologies. The large metabolic generation rate and low tolerance to elevated levels of carbon dioxide (CO2) in the Mars atmosphere make CO2 removal one of the preeminent tasks in this domain. In addition, these same features provide a strong impetus for using regenerable CO2 removal technologies. In the past, many of these regenerable technologies have relied on the low partial pressure CO2 surrounding the vehicle to provide an ultimate sink for removing this gas contaminant, however any Mars mission will have to overcome the presence of the Mars atmosphere. This paper describes the investigation of methods to capture the exhaled CO2 from a suited crewmember before it becomes diluted with the high volumetric air flow present within the space suit. Typical expired air contains CO2 partial pressures in the range of 20-35 mm Hg. This research investigated methods to capture this high partial pressure CO2 prior to its dilution with the low partial pressure CO2 ventilation flow. Specifically the research looked at potential designs for a collection cup for use inside the space suit helmet. This collection cup should not be considered the same as a breathing mask typical of that worn by firefighters, etc. Instead, the collection cup is a non-contact device that makes use of detailed analyses of the ventilation flow environment within the helmet. The research used a detailed Computational Fluid Dynamic (CFD) code called Fluent to provide modeling of the various gas species (CO2, water vapor, O2) as they pass through a helmet. This same model was used to numerically evaluate several different collection cup designs for this same CO2 segregation effort.

Paul, Heather↗