SEARCH · Engineering Papers

Results for “solar panel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS1976

Ultrahigh-accuracy body-pointing system for the Large Space Telescope

The Large Space Telescope (LST) is a 3-m diffraction-limited telescope. Pointing stability requirements necessary to assure diffraction-limited images are plus or minus 0.005 arc-sec, over possible experiment observation times of several hours. In order to determine whether these stringent pointing requirements could be met, a complex simulation model was defined which consisted of detailed dynamic representations of control moment gyros (CMGs) and reaction wheels (RWs), including their noise characteristics, dynamic sensor representations with sensor noise, shock mounts for the CMG actuators, a detailed representation of an image motion compensation (IMC) system, and a detailed flexible body structural model with all significant vehicle and solar panel bending modes. On the basis of both stability and performance studies utilizing this model, it was determined that a body-pointing system will meet LST requirements in the presence of CMG vibrational disturbances and sensor noise. The recommended system consists of three orthogonally mounted RWs for primary short-term control, and a cluster of CMG actuators for continuous RW desaturation and vehicle maneuvering.

Rybak, S. C.↗

NASA NTRS1975

ATS-6 spacecraft - An EMC challenge

A series of analytical, measurement, and experimental EMI tests were performed on ATS-6. The EMC problems encountered included: (1) wiring pickup and reradiation, (2) input rectification and bias offset, (3) harmonics, (4) component degradation, (5) unbalanced shield ground, (6) inadvertent pickup, and (7) electro-explosive devices. The test program consisted of materials evaluation (with regard to shielding effectiveness, cost, weight, etc.), sun sensor RF susceptibility, cable shielding material evaluation, RF integrity of solar panels and power harnesses, anechoic chamber tests, bonding and grounding, and shielding and thermal control.

Kampinsky, A.↗

NASA NTRS1975

The SAS-3 X-ray observatory

The experiment section of the Small Astronomy Satellite-3 (SAS-3) launched in May 1975 is an X-ray observatory intended to determine the location of bright X-ray sources to an accuracy of 15 arc-seconds; to study a selected set of sources over a wide energy range, from 0.1 to 55 keV, while performing very specific measurements of the spectra and time variability of known X-ray sources; and to monitor the sky continuously for X-ray novae, flares, and unexpected phenomena. The improvements in SAS-3 spacecraft include a clock accurate to 1 part in 10 billion, rotatable solar panels, a programmable data format, and improved nutation damper, a delayed command system, improved magnetic trim and azimuth control systems. These improvements enable SAS-3 to perform three-axis stabilized observations of any point on the celestial sphere at any time of the year. The description of the experiment section and the SAS-3 operation is followed by a synopsis of scientific results obtained from the observations of X-ray sources, such as Vela X-1 (supposed to be an accreting neutron star), a transient source of hard X-ray (less than 36 min in duration) detected by SAS-3, the Crab Nebula pulsar, the Perseus cluster of galaxies, and the Vela supernova remnant.

Mayer, W. F.↗

NASA NTRS1977

Changing sunlight to microwaves: A concept

Electromechanical device converts sunlight into microwave energy by direct process. Still in conceptual stage, device is expected to be lighter and more efficient (ninety percent conversion efficiency) than less-direct conversion systems that employ solar panels and magnetrons. Besides uses in satellites and spacecraft as microwave source, device has many terrestrial applications, including use in fuel-saving sun-powered microwave oven.

Dickinson, R. M.↗

NASA NTRS1977

Photovoltaic, gravitationally-stabilized solid-state, satellite solar power station /GSS4PS/

The salient feature of a gravitationally-stabilized satellite solar power system (SSPS) for a photovoltaic system is that the large solar array is separated into smaller segments or subunits, joined together in a linear array oriented along the local vertical. Applicability of gravitational stabilization to the design of photovoltaic SSPS is demonstrated. Both actively controlled systems using multiple solar panels oriented to the sun and passively controlled systems requiring no sun orientation are considered and determined to be feasible. Expressions for gravity-gradient induced tension and restoring torques about the local vertical are assessed. Particular attention is directed to the applicability of solid-state approaches to the design of SSPS. It is shown that an all solid-state SSPS utilizing the LITOMIC (light-to-microwave conversion) concept is feasible but that a hybrid system employing a combination of both solid-state and cryogenic cooled low-voltage techniques to the design of the power management and distribution subsystem may also provide a solution.

Cantafio, L. J.↗

NASA NTRS1977

Specifying spacecraft flexible appendage rigidity

As a method for specifying the required degree of rigidity of spacecraft flexible appendages, an analytical technique is proposed for establishing values for the frequency, damping ratio, and modal gain (deflection) of the first several bending modes. The shortcomings of the technique result from the limitations associated with the order of the equations that can be handled practically. An iterative method is prescribed for handling a system whose structural flexibility is described by more than one normal mode. The analytical technique is applied to specifying solar panel rigidity constraints for the NASA Space Telescope. The traditional nonanalytic procedure for specifying the required degree of rigidity of spacecraft flexible appendages has been to set a lower limit below which bending mode frequencies may not lie.

Seltzer, S. M.↗

NASA NTRS1977

Pioneer Venus spacecraft charging model

Five environmental models were constructed to represent the solar wind and the upper, middle, and lower ionosphere of Venus. The spacecraft structure was modeled with over 140 passive electrical elements representing structural elements of the spacecraft. Electron, ion, secondary electron, and photocurrents to the spacecraft from the plasma were calculated, ignoring sheath effects. In all but one case, potentials of interest were less than 1 volt. Potential differences between widely separated points on the equipment shelf were less than 1 mV. The one area of concern is the solar panel potential when the orbiter is passing through the bowshock region.

Robinson, P. A., Jr.↗

NASA NTRS1977

The Goddard Space Flight Center high efficiency cell development and evaluation program

Laboratory tests and flight experiments showed that solar cells can be produced in quantity, that they are suitable for space flight applications, and that the power produced ranged from 20 to 35% more than that of conventional cells. In a benign flight environment, the cells degraded at approximately the same rate as conventional cells. In synchronous orbit, the rate exceeded that of conventional cells, but high efficiency cells still showed significant power advantage after two years. Irradiation test results showed the voltage-temperature coefficients to be comparable to conventional cells. However, current-temperature coefficients were not only higher initially, but also increased significantly with irradiation. Although thin cells with good performance characteristics were made, significant problem areas pertinent to production were disclosed, particularly for cells with thickness of 0.100 mm or less. The overall program led to the use of advanced high efficiency cells on the International Sun-Earth Explorer solar panels.

Slifer, L. W.↗

NASA NTRS1967

Wabble gear drive mechanism

The wabble gear principle was applied in the design of a driving mechanism for controlling spacecraft solar panels. The moving elements, other than the output gear, are contained within a hermetically sealed package to prevent escape of lubricants and ingestion of contaminant particles. The driving gear contains one more tooth than the output gear on a concave, conical pitch surface of slightly larger apex angle. The two gears mesh face to face such that engagement takes place at one point along the circumference. The driving gear is not permitted to rotate by virtue of its attachment through the bellows which permits flexure in the pitch and yaw position, but not in roll. As the bearing carrier rotates, the inclined mounting of the bearing causes the driving gear to perform a wabbling, irrotational motion. This wabbling motion causes the contact point between the output gear and the driving gear to traverse around the circumference of the gears once per revolution of the bearing carrier.

Winiarski, F. J.↗

NASA NTRS1977

Inhibitor analysis for a solar heating and cooling system

A study of potential corrosion inhibitors for the NASA solar heating and cooling system which uses aluminum solar panels is provided. Research consisted of testing using a dynamic corrosion system, along with an economic analysis of proposed corrosion inhibitors. Very good progress was made in finding a suitable inhibitor for the system.

Tabony, J. H.↗

NASA NTRS1976

Results of accelerated thermal cycle tests of solar cells modules

Various candidate solar panel designs were evaluated, both theoretically and experimentally, with respect to their thermal cycling survival capability, and in particular with respect to an accelerated simulation of thermal cycles representative of Viking '75 mission requirements. The experimental results were obtained on 'mini-panels' thermally cycled in a newly installed automated test facility herein described. The resulting damage was analyzed physically and theoretically, and on the basis of these analyses the panel design was suitably modified to significantly improve its ability to withstand the thermal environment. These successful modifications demonstrate the value of the complementary theoretical-experimental approach adopted, and discussed in detail in this paper.

Berman, P.↗

NASA NTRS1979

Assembling solar-cell arrays

Modified 70 mm movie film editor automatically attaches solar cells to flexible film substrate. Machine can rapidly and inexpensively assemble cells for solar panels at rate of 250 cells per minute. Further development is expected to boost production rate to 1000 cells per minute.

Bloch, J. T.↗

NASA NTRS1978

A demonstration of the value of general purpose, on-board satellite computers

Failure of the solar panels to erect and spin stabilize the TRANSIT Improvement Program (TIP) satellites is discussed, with emphasis on how the flight computer was reprogrammed to perform various control functions in order to achieve a partial mission success. These functions include: (1) power management to avoid troublesome spacecraft blackouts; (2) achieve enough spin stability to fire the OATS thruster; (3) raise the parking orbit to a workable altitude; (4) remove a high tumble rate which was the indirect result of the failure; and (5) deploy the gravity-gradient boom successfully on TIP-3.

Jenkins, R. E.↗

NASA NTRS1979

Visual imaging control systems of the Mariner to Jupiter and Saturn spacecraft

Design and fabrication of optical systems for the Mariner Jupiter Saturn (Voyager) mission is described. Because of the long distances of these planets from the sun, the spacecraft was designed without solar panels with the electricity generated on-board by radio-isotope thermal generators (RTG). The presence of RTG's and Jupiter radiation environment required that the optical systems be fabricated out of radiation stabilized materials. A narrow angle and a wide angle camera are located on the spacecraft scan platform, with the narrow angle lens a modification of the Mariner 10 lens. The optical system is described, noting that the lens was modified by moving the aperture correctors forward and placing a spider mounted secondary mirror in the original back surface of the second aperture corrector. The wide angle lens was made out of cerium doped, radiation stabilized optical glass with greatest blue transmittance, which would be resistant to RTG and Jupiter radiation.

Larks, L.↗

NASA NTRS1978

A low cost, durable anti-reflective film for solar collectors

The physics of reflection reduction by thin films is briefly reviewed. Current techniques for the production of anti-reflective coatings are surveyed with respect to their applicabilities to solar panel covers. Techniques for the production of suitable anti-reflection coatings based on acid-hardened sodium silicate solutions are presented along with optical data for both acid-leached and silicate coatings

Pastirik, E. M.↗

NASA NTRS1979

Trends in Materials' Outgassing Technology

Test sample acquisition and chemical analysis techniques for outgassing products from spacecraft, experiment modules, and support equipment is described. The reduction of test data to a computer compatible format to implement materials selection policies is described. A list of the most troublesome outgassing species is given and several materials correlations are discussed. Outgassing from solar panels, thermal blankets, and wire insulation are examined individually.

Colony, J. A.↗

NASA NTRS1982

Solar-Powered Supply Is Light and Reliable

DC supply originally intended for use in solar-powered spacecraft propulsion is lightweight and very reliable. Operates from 100-200 volt output of solar panels to produce 11 different dc voltages, with total demand of 3,138 watts. With exception of specially wound inductors and transformers, system uses readily available components.

Willis, A. E.↗

NASA NTRS1982

Finite-Element Analysis of Forced Convection and Conduction

TAP2 thermal-analysis program was developed as part of research on finite element methodology for thermal analysis of convectively cooled structures, such as scramjet engines and hypersonic aircraft. Program simplifies computations when both structural and thermal analyses are required and is suited for thermal analysis of nuclear reactors and solar-panel heating systems.

Wieting, A. R.↗