SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Supplementary data tables for single stage experimental evaluation of compressor blading with slots and vortex generators
Data and performance of stage four of compressor blades with slots and vortex generators
Slot antenna radiation pattern distortion produced by boundary layer plasma sheath around conical reentry vehicles
Additional slot and flow fence effects on aerodynamic characteristics of single stage compressor blading
Finite difference calculation based on eddy diffusivity and mixing length flow theory to characterize supersonic turbulent boundary layer with tangential slot injection
Wind tunnel investigation of use of slotted test-section walls to reduce wall interference for high-lift-model testing
Slotted blades and vanes and rotor tip design for highly loaded, low speed fan stage applicable to low noise aircraft engines
Wind tunnel tests of swept wing jet transport aircraft model with four pod mounted engines under wing and external flow, jet augmented double slotted flap
Wind tunnel investigation of external-flow jet-flap transport configuration having full-span tripple-slotted flaps - graphs
Design, characteristics, and performance tests of short two dimensional curved wall diffusers using suction slots
Turbulent boundary layers calculation downstream of compressible relaxing slot injection flows, using finite difference method based on eddy viscosity model
A numerical method is presented for calculating the boundary-induced interference at subsonic speeds. The wind tunnel slot width or wall porosity can vary throughout the test section. The interference can be computed at any point in the test section. The model can be any configuration and can be located anywhere in the test section. Several examples are given, and comparison is made with other methods where available.
An analysis is presented for compressible fluid flow across shaft face seals and narrow slots. The analysis includes fluid inertia, viscous friction, and entrance losses. Subsonic and choked flow conditions can be predicted and analyzed. The model is valid for both laminar and turbulent flows. Results agree with experiment and with solutions which are more limited in applicability. Results show that a parallel film can have a positive film stiffness under choked flow conditions.
A simplified model is suggested for engineering estimates of heat transfer in the vicinity of reattachment for the case of supersonic flow over a backward facing step with a suction slot. The presented approach gives a closed-form approximate solution which is shown to be in satisfactory agreement with experimental results for the case of no mass transfer, and is expected to predict the effect of mass transfer in the case of suction.
A computer program is presented for compressible fluid flow with friction across face seals and through narrow slots. The computer program carries out a quasi-one-dimensional flow analysis which is valid for laminar and turbulent flows under both subsonic and choked flow conditions for parallel surfaces. The program is written in FORTRAN IV. The input and output variables are in either the International System of Units (SI) or the U.S. customary system.
A two-dimensional liquid-metal slot jet that is impinging normally against a uniformly heated flat plate is analyzed. The distributions of wall temperature and heat-transfer coefficient are obtained as functions of position along the plate. The liquid-metal assumptions are made that the jet is inviscid and that molecular condition is dominating heat diffusion. The solution is obtained by mapping the jet flow region into a potential plane where it occupies a strip of uniform width. The energy equation is transformed into potential coordinates, and an exact solution obtained in the strip region. Conformal mapping is then used to transform the solution into the physical plane.
The noise generated by a 2.26- by 11.43-cm slot nozzle with a V-gutter reverser, as well as some aerodynamic data on flow, thrust-reversal efficiency, and nozzle jet velocity decay were studied. The experimental data are scaled up to sizes suitable for reversing the wing flow of a 45/400-kg augmentor-wing-type STOL airplane, yielding perceived noise levels well above the 95-PNdb design goal on the 152-m sideline. The reverser, in addition to being noisier than the nozzle alone, also had a more uniform directional distribution and more high frequency noise. The maximum overall sound pressure level and the effective sound power level both varied with the sixth power of nozzle jet velocity. Preliminary experiments indicated possible sideline noise reduction by shielding.
The electrohydraulically actuated slotted-plate bypass valve used to control the position of the normal shock during wind-tunnel investigations of supersonic inlets also has proven to be a valuable device for determining inlet dynamics and creating airflow disturbances. Operation of previous valves at high frequencies (to 100 Hz) for extended testing has resulted in numerous failures. An improved bypass-valve design is presented which increases the cyclic tolerance of the device considerably over past designs. The use of dynamic limit criteria to obtain an optimum actuator-piston size results in a frequency response which is flat within + or - 3 decibels to 120 Hz for a peak-to-peak variation of 20 percent of full area.