Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pressure gradient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Some Scenarios for Transition on Turbomachinery Blading

Measurements on transition under different levels of adverse pressure gradient and free-stream turbulence level are described. This extensive series of investigations, which was predicated on intermittency measurement techniques, has resulted in correlations for transition length and turbulent spot formation rate. These correlations rae intended to be used in conjunction with boundary layer prediction methods and examples are given of such predictions. More effective predictions of the transition region, especially under conditions of variable pressure gradient, are dependent on a more comprehensive understanding of transition and spot behavior. It is expected that this will result in improved transition modeling.

Gostelow, J. P.↗
NASA NTRS1986

Numerical simulation of a controlled boundary layer

The problem of interest is the boundary layer over a flat plate. The three standard laminar flow control (LFC) techniques are pressure gradient, suction, and heating. The parameters used to describe the amount of control in the context of the boundary layer equations are introduced. The numerical method required to find the mean flow, the linear eigenvalues of the Orr-Sommerfeld equation, and the full, nonlinear, 3-D solution of the Navier-Stokes equations are outlined. A secondary instability exists for the parallel boundary subject to uniform pressure gradient, suction, or heating. Selective control of the spanwise mode reduces the secondary instability in the parallel boundary layer at low Reynolds number.

Zang, Thomas A.↗
NASA NTRS1995

An experimental study of a turbulent boundary layer in the trailing edge region of a circulation-control airfoil

This report describes the development of a new near-wall LDV technique and its use to measure the full turbulent stress tensor in a highly three-dimensional separated boundary layer flow. Laser Doppler velocimetry, with small diameter laser beams allowing small beam-crossing angles (i.e., larger fringe spacings), was used, resulting in measurements close to solid surfaces. Dennis Johnson of NASA/Ames combined the advantages offered by FFT signal processors with a beam-steering probe inserted in the flow to devise a new self-aligning, near-wall LDV approach capable of making direct measurements of the transverse velocity component. This new technique was applied to a 2D, zero-pressure-gradient, flat-plate boundary layer in the High Reynolds Number Pilot Channel at Ames. Accurate and repeatable measurements of U and uu to within 30 mm of the wall were obtained. Next, the near-wall LDV technique was employed in a 3D separated boundary layer flow, consisting of a 2-dimensional wall boundary layer approaching a right-angle wedge. The resulting lateral and adverse streamwise pressure gradients generated significant spanwise velocities and turbulent stresses, and a large reverse-flow region. The near-wall LDV was modified further to facilitate measurements in the 3D Wedge Flow.

Brown, Jeffrey↗
NASA NTRS2008

Supersonic/Hypersonic Laminar Heating Correlations for Rectangular and Impact-Induced Open and Closed Cavities

Impact and debris damage to the Space Shuttle Orbiter Thermal Protection System tiles is a random phenomenon, occurring at random locations on the vehicle surface, resulting in random geometrical shapes that are exposed to a definable range of surface flow conditions. In response to the 2003 Final Report of the Columbia Accident Investigation Board, wind tunnel aeroheating experiments approximating a wide range of possible damage scenarios covering both open and closed cavity flow conditions were systematically tested in hypersonic ground based facilities. These data were analyzed and engineering assessment tools for damage-induced fully-laminar heating were developed and exercised on orbit. These tools provide bounding approximations for the damaged-surface heating environment. This paper presents a further analysis of the baseline, zero-pressure-gradient, idealized, rectangular-geometry cavity heating data, yielding new laminar correlations for the floor-averaged heating, peak cavity endwall heating, and the downstream decay rate. Correlation parameters are derived in terms of cavity geometry and local flow conditions. Prediction Limit Uncertainty values are provided at the 95%, 99% and 99.9% levels of significance. Non-baseline conditions, including non-rectangular geometries and flows with known pressure gradients, are used to assess the range of applicability of the new correlations. All data variations fall within the 99% Prediction Limit Uncertainty bounds. Importantly, both open-flow and closed-flow cavity heating are combined into a single-curve parameterization of the heating predictions, and provide a concise mathematical model of the laminar cavity heating flow field with known uncertainty.

Everhart, Joel L.↗
NASA NTRS1992

The stability of the near-Earth magnetotail against the ballooning instability

In an extension to a previous study, conditions for the ballooning instability in the magnetohydrodynamic approximation are derived. It is necessary for exciting the ballooning instability that the plasma pressure is higher where plasma is convected outward. However, the expansion of plasma, which results from the divergence of outward flows in the curved geometry of field lines, may overcompensate for the convective change in the plasma pressure. Conditions for the instability are derived from the equation describing the linear coupling between the Alfven and slow magnetosonic waves. The result indicates that excessive curvature stabilizes, rather than destabilizes, perturbations, as well as the field aligned current and the field aligned flow. That is the field line curvature should be smaller than the pressure gradient for exciting the ballooning instability. It is inferred that this condition is not satisfied during quiet times in the near Earth tail. The plasma sheet becomes more stable to the instability in accordance with the thinning of the plasma sheets during the growth phase of substorms, while in the region nearer to the Earth (the inner edge of the plasma sheet or the ring current region) the plasma pressure gradient, which is possibly localized during the growth phase, may drive the instability.

Ohtani, Shin-Ichi↗
NASA NTRS1977

Experimental and theoretical investigation of three-dimensional turbulent boundary layers and turbulence characteristics inside an axial flow inducer passage

Analytical and experimental investigations of the characteristics of three dimensional turbulent boundary layers in a rotating helical passage of an inducer rotor are reported. Expressions are developed for the velocity profiles in the inner layer, where the viscous effects dominate, in the outer layer, where the viscous effects are small, and in the interference layer, where the end walls influence the flow. The prediction of boundary layer growth is based on the momentum integral technique. The equations derived are general enough to be valid for all turbomachinery rotors with arbitrary pressure gradients. The experimental investigations are carried out in a flat plate inducer 3 feet in diameter. The mean velocity profiles, turbulence intensities and shear stresses, wall shear stress, and limiting streamline angles are measured at various radial and chordwise locations by using rotating probes. The measurements are in general agreement with the predictions. The radial flows are well represented by an expression which includes the effect of stagger angle and radial pressure gradient. The radial flows in the rotor channel are higher than those on a single blade. The collateral region exists only very near the blade surface. The radial component of turbulence intensity is higher than the streamwise component because of the effect of rotation.

Anand, A. K.↗
NASA NTRS1996

High lift wake investigation

The behavior of wakes in adverse pressure gradients is critical to the performance of high-lift systems for transport aircraft. Wake deceleration is known to lead to sudden thickening and the onset of reversed flow; this 'wake bursting' phenomenon can occur while surface flows remain attached. Although known to be important for high-lift systems, few studies of such decelerated wakes exist. In this study, the wake of a flat plate has been subjected to an adverse pressure gradient in a two-dimensional diffuser, whose panels were forced to remain attached by use of slot blowing. Pitot probe surveys, L.D.V. measurements, and flow visualization have been used to investigate the physics of this decelerated wake, through the onset of reversed flow.

Sullivan, J. P.↗
NASA NTRSDate not supplied

On Generalizably Improving RANS Predictions of Flow Separation and Reattachment

This work presents progress in an ongoing data-driven turbulence modeling effort at NASA Langley Research Center to improve predictions for separated flows. Two augmentation strategies are presented – one to improve predictions for the point of reattachment after smooth-body separation, and another to improve predictions for flow separation due to prolonged adverse pressure gradients. The reattachment augmentation was inspired from lessons learned during attempts at using field inversion and machine learning (FIML); however, it is prescribed as a conventional analytic closed-form expression. Results show that, when introduced into the SST k-w model, it shortens the otherwise overpredicted separation bubble length for three cases characterized by different Reynolds numbers and flow geometries. The second augmentation, which addresses flow separation under prolonged adverse pressure gradients, is inferred via FIML and applied as a neural network within the Spalart-Allmaras model. It uses features that are chosen such that the presented results show an improved predictive accuracy for the training case without affecting other cases where the augmentation is not needed. Further testing is required to establish the generalizability of this augmentation. The rationale behind the chosen features that serve as inputs to both these augmentations is also presented for the benefit of the reader.

machine learning↗
NASA NTRS1992

Nozzle material requirements and the status of intermetallic matrix composites

The HSCT exhaust nozzle must manage high temperature exhaust gases and pressure gradients while meeting HSCT economic and noise goals. The important features and requirements for an HSCT exhaust nozzle are shown for a 2DCD (two-dimensional convergent-divergent) design. The same requirements would apply to an axisymmetric design. Exhaust nozzle weight has an adverse effect on the overall aircraft range, payload, and engine specific fuel consumption and is therefore the primary driver for advanced exhaust nozzle materials. Because of the large airflow and pressure gradients, exhaust nozzles are extremely large and heavy when made from current materials. The use of advanced materials with higher specific strength will reduce the weight of exhaust nozzle components. In addition to the flow of high-temperature exhaust gases into the exhaust nozzle, ambient air is entrained to reduce gas exit velocities and suppress sound. This leads to components exposed to extremely high temperature gradients and, hence, high thermal stresses. Further, exhaust gases are highly oxidizing; material environmental resistance will be an important factor for long life. Several viable concepts have been identified to reduce noise through the mixture of exhaust and ambient air. Sound can be further suppressed by acoustic panels that absorb high-frequency noise.

Johnson, Andrew M.↗
NASA NTRS1996

Studies of Two-Phase Flow Dynamics and Heat Transfer at Reduced Gravity Conditions

The ability to predict gas-liquid flow patterns is crucial to the design and operation of two-phase flow systems in the microgravity environment. Flow pattern maps have been developed in this study which show the occurrence of flow patterns as a function of gas and liquid superficial velocities as well as tube diameter, liquid viscosity and surface tension. The results have demonstrated that the location of the bubble-slug transition is affected by the tube diameter for air-water systems and by surface tension, suggesting that turbulence-induced bubble fluctuations and coalescence mechanisms play a role in this transition. The location of the slug-annular transition on the flow pattern maps is largely unaffected by tube diameter, liquid viscosity or surface tension in the ranges tested. Void fraction-based transition criteria were developed which separate the flow patterns on the flow pattern maps with reasonable accuracy. Weber number transition criteria also show promise but further work is needed to improve these models. For annular gas-liquid flows of air-water and air- 50 percent glycerine under reduced gravity conditions, the pressure gradient agrees fairly well with a version of the Lockhart-Martinelli correlation but the measured film thickness deviates from published correlations at lower Reynolds numbers. Nusselt numbers, based on a film thickness obtained from standard normal-gravity correlations, follow the relation, Nu = A Re(sup n) Pr(exp l/3), but more experimental data in a reduced gravity environment are needed to increase the confidence in the estimated constants, A and n. In the slug flow regime, experimental pressure gradient does not correlate well with either the Lockhart-Martinelli or a homogeneous formulation, but does correlate nicely with a formulation based on a two-phase Reynolds number. Comparison with ground-based correlations implies that the heat transfer coefficients are lower at reduced gravity than at normal gravity under the same flow conditions. Nusselt numbers can be correlated in a fashion similar to Chu and Jones.

Witte, Larry C.↗
NASA NTRS1993

Underwing compression vortex attenuation device

A vortex attenuation device is presented which dissipates a lift-induced vortex generated by a lifting aircraft wing. The device consists of a positive pressure gradient producing means in the form of a compression panel attached to the lower surface of the wing and facing perpendicular to the airflow across the wing. The panel is located between the midpoint of the local wing cord and the trailing edge in the chord-wise direction and at a point which is approximately 55 percent of the wing span as measured from the fuselage center line in the spanwise direction. When deployed in flight, this panel produces a positive pressure gradient aligned with the final roll-up of the total vortex system which interrupts the axial flow in the vortex core and causes the vortex to collapse.

Patterson, James C., Jr.↗
NASA NTRS1993

The structure of a three-dimensional turbulent boundary layer

The three-dimensional turbulent boundary layer is shown to have a self-consistent two-layer asymptotic structure in the limit of large Reynolds number. In a streamline coordinate system, the streamwise velocity distribution is similar to that in two-dimensional flows, having a defect-function form in the outer layer which is adjusted to zero at the wall through an inner wall layer. An asymptotic expansion accurate to two orders is required for the cross-stream velocity which is shown to exhibit a logarithmic form in the overlap region. The inner wall-layer flow is collateral to leading order but the influence of the pressure gradient, at large but finite Reynolds numbers, is not negligible and can cause substantial skewing of the velocity profile near the wall. Conditions under which the boundary layer achieves self-similarity and the governing set of ordinary differential equations for the outer layer are derived. The calculated solution of these equations is matched asymptotically to an inner wall-layer solution and the composite profiles so formed describe the flow throughout the entire boundary layer. The effects of Reynolds number and cross-stream pressure gradient on the crossstream velocity profile are discussed and it is shown that the location of the maximum cross-stream velocity is within the overlap region.

Degani, A. T.↗
NASA NTRS1998

The Control of Compressible Dynamic Stall Using Adaptive Airfoils

Ongoing research has shown that compressible dynamic stall can be caused by vastly different mechanisms even for small changes in flow conditions. For example, at low Mach numbers (M less than 0.3) and Reynolds numbers (less than 1 x 10(exp 6)), the bursting of the laminar separation bubble induces dynamic stall. At a slightly higher Mach number (M = 0.45) and around the same Reynolds number, shock induced separation can cause dynamic stall. Also, the mechanism changes from that of laminar separation bubble bursting to that due to excessive adverse pressure gradient, with increase of Reynolds number. Complex interactions occurring between the local supersonic flow and the bubble lead to another possible mechanism of dynamic stall. Since all these mechanisms may be encountered by a rotor-blade during a single cycle, there is a strong need to devise a reliable flow control method for use under such dramatically varying conditions. Whereas it is a Ali 'Beneficent challenge, identification of the fact that these mechanisms are all in some way related to the airfoil leading edge adverse pressure gradient, has resulted in an effective method of flow control to be described.

Chandasekhara, M. S.↗
NASA NTRS1992

Improved two-equation k-omega turbulence models for aerodynamic flows

Two new versions of the k-omega two-equation turbulence model will be presented. The new Baseline (BSL) model is designed to give results similar to those of the original k-omega model of Wilcox, but without its strong dependency on arbitrary freestream values. The BSL model is identical to the Wilcox model in the inner 50 percent of the boundary-layer but changes gradually to the high Reynolds number Jones-Launder k-epsilon model (in a k-omega formulation) towards the boundary-layer edge. The new model is also virtually identical to the Jones-Lauder model for free shear layers. The second version of the model is called Shear-Stress Transport (SST) model. It is based on the BSL model, but has the additional ability to account for the transport of the principal shear stress in adverse pressure gradient boundary-layers. The model is based on Bradshaw's assumption that the principal shear stress is proportional to the turbulent kinetic energy, which is introduced into the definition of the eddy-viscosity. Both models are tested for a large number of different flowfields. The results of the BSL model are similar to those of the original k-omega model, but without the undesirable freestream dependency. The predictions of the SST model are also independent of the freestream values and show excellent agreement with experimental data for adverse pressure gradient boundary-layer flows.

Menter, Florian R.↗
NASA NTRS1993

Zonal Two Equation Kappa-Omega Turbulence Models for Aerodynamic Flows

Two new versions of the kappa-omega two-equation turbulence model will be presented. The new Baseline (BSL) model is designed to give results similar to those of the original kappa-omega model of Wilcox, but without its strong dependency on arbitrary freestream values. The BSL model is identical to the Wilcox model in the inner 50% of the boundary-layer but changes gradually to the standard kappa-epsilon model (in a kappa- omega formulation) towards the boundary-layer edge. The free shear layers. The second version of the model is called Shear-Stress Transport (SST) model. It is a variation of the BSL model with the additional ability to account for the transport of the principal turbulent shear stress in adverse pressure gradient boundary-layers. The model is based on Bradshaw's assumption that the principal shear-stress is proportional to the turbulent kinetic energy, which is introduced into the definition of the eddy-viscosity. Both models are tested for a large number of different flowfields. The results of the BSL model are similar to those of the original kappa-omega model, but without the undesirable freestream dependency. The predictions of the SST model are also independent of the freestream values but show better agreement with experimental data for adverse pressure gradient boundary-layer flows.

Menter, Florian R.↗
NASA NTRS2005

Analysis of Transition-Sensitized Turbulent Transport Equations

The dynamics of an ensemble of linear disturbances in boundary-layer flows at various Reynolds numbers is studied through an analysis of the transport equations for the mean disturbance kinetic energy and energy dissipation rate. Effects of adverse and favorable pressure-gradients on the disturbance dynamics are also included in the analysis Unlike the fully turbulent regime where nonlinear phase scrambling of the fluctuations affects the flow field even in proximity to the wall, the early stage transition regime fluctuations studied here are influenced cross the boundary layer by the solid boundary. The dominating dynamics in the disturbance kinetic energy and dissipation rate equations are described. These results are then used to formulate transition-sensitized turbulent transport equations, which are solved in a two-step process and applied to zero-pressure-gradient flow over a flat plate. Computed results are in good agreement with experimental data.

Rumsey, Christopher L.↗
NASA NTRS1998

Transition Heat Transfer Modeling Based on the Characteristics of Turbulent Spots

While turbulence models are being developed which show promise for simulating the transition region on a turbine blade or vane, it is believed that the best approach with the greatest potential for practical use is the use of models which incorporate the physics of turbulent spots present in the transition region. This type of modeling results in the prediction of transition region intermittency which when incorporated in turbulence models give a good to excellent prediction of the transition region heat transfer. Some models are presented which show how turbulent spot characteristics and behavior can be employed to predict the effect of pressure gradient and Mach number on the transition region. The models predict the spot formation rate which is needed, in addition to the transition onset location, in the Narasimha concentrated breakdown intermittency equation. A simplified approach is taken for modeling turbulent spot growth and interaction in the transition region which utilizes the turbulent spot variables governing transition length and spot generation rate. The models are expressed in terms of spot spreading angle, dimensionless spot velocity, dimensionless spot area, disturbance frequency and Mach number. The models are used in conjunction with a computer code to predict the effects of pressure gradient and Mach number on the transition region and compared with VKI experimental turbine data.

Simon, Fred↗
NASA NTRS2008

Nonlinear Reduced-Order Analysis with Time-Varying Spatial Loading Distributions

Oscillating shocks acting in combination with high-intensity acoustic loadings present a challenge to the design of resilient hypersonic flight vehicle structures. This paper addresses some features of this loading condition and certain aspects of a nonlinear reduced-order analysis with emphasis on system identification leading to formation of a robust modal basis. The nonlinear dynamic response of a composite structure subject to the simultaneous action of locally strong oscillating pressure gradients and high-intensity acoustic loadings is considered. The reduced-order analysis used in this work has been previously demonstrated to be both computationally efficient and accurate for time-invariant spatial loading distributions, provided that an appropriate modal basis is used. The challenge of the present study is to identify a suitable basis for loadings with time-varying spatial distributions. Using a proper orthogonal decomposition and modal expansion, it is shown that such a basis can be developed. The basis is made more robust by incrementally expanding it to account for changes in the location, frequency and span of the oscillating pressure gradient.

Prezekop, Adam↗