Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Next-generation anion exchange membrane water electrolyzers operating for commercially relevant lifetimes

Alkaline anion exchange membrane (AEM) water electrolysis has gained increasing attention due to its potential to achieve low-cost, high performance hydrogen production. However, most existing membranes are not durable in industrial settings. In this work, we demonstrate good performance relative to industrial parameters using Sustainion® anion exchange membranes. Long-duration tests showed stable performance of 1 A/cm 2 at 1.85 V with a degradation rate of less than 1 μV/h over 10,000 h. The projected lifetime is thus over 20 years. Daily on/off cycling performance over the course of 30 years was simulated experimentally through accelerated voltage shock tests, resulting in a performance loss of only 0.15 μV/cycle over 11,000 cycles. As shown through impact and crossover testing, an improvement in performance is achieved by the addition of zirconia to the polymer matrix and mechanically reinforcing the membrane.

08 HYDROGEN↗
DOE OSTI2021

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics--based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.

Kulkarni, Shank S.↗
DOE OSTI2024

Supported Platinum Nanoparticles Catalyzed Carbon–Carbon Bond Cleavage of Polyolefins: Role of the Oxide Support Acidity

Supported platinum nanoparticle catalysts are known to convert polyolefins to high-quality liquid hydrocarbons using hydrogen under relatively mild conditions. To date, few studies using platinum grafted onto various metal oxide (M x O y ) supports have been undertaken to understand the role of the acidity of the oxide support in the carbon-carbon bond cleavage of polyethylene under consistent catalytic conditions. Specifically, two Pt/M x O y catalysts (M x O y = SrTiO 3 and SiO 2 -Al 2 O 3 ; Al = 3.0 wt %, target Pt loading 2 wt % Pt similar to 1.5 nm), under identical catalytic polyethylene hydrogenolysis conditions (T = 300 degree celsius, P(H 2 ) = 170 psi, t = 24 h; M w = similar to 3,800 g/mol, M n = similar to 1,100 g/mol, D = 3.45, N branch/100C = 1.0), yielded a narrow distribution of hydrocarbons with molecular weights in the range of lubricants (M w = < 600 g/mol; M n < 400 g/mol; D = 1.5). While Pt/SrTiO 3 formed saturated hydrocarbons with negligible branching, Pt/SiO 2 -Al 2 O 3 formed partially unsaturated hydrocarbons (<1 mol % alkenes and similar to 4 mol % alkyl aromatics) with increased branch density (N branch/100C = 5.5). Further investigations suggest evidence for a competitive hydrocracking mechanism occurring alongside hydrogenolysis, stemming from the increased acidity of Pt/SiO 2 -Al 2 O 3 compared to Pt/SrTiO 3 . Additionally, the products of these polymer deconstruction reactions were found to be independent of the polyethylene feedstock, allowing the potential to upcycle polyethylenes with various properties into a value-added product.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Foundry-compatible high-resolution patterning of vertically phase-separated semiconducting films for ultraflexible organic electronics

Solution processability of polymer semiconductors becomes an unfavorable factor during the fabrication of pixelated films since the underlying layer is vulnerable to subsequent solvent exposure. A foundry-compatible patterning process must meet requirements including high-throughput and high-resolution patternability, broad generality, ambient processability, environmentally benign solvents, and, minimal device performance degradation. However, known methodologies can only meet very few of these requirements. Here, a facile photolithographic approach is demonstrated for foundry-compatible high-resolution patterning of known p- and n-type semiconducting polymers. This process involves crosslinking a vertically phase-separated blend of the semiconducting polymer and a UV photocurable additive, and enables ambient processable photopatterning at resolutions as high as 0.5 μm in only three steps with environmentally benign solvents. The patterned semiconducting films can be integrated into thin-film transistors having excellent transport characteristics, low off-currents, and high thermal (up to 175 °C) and chemical (24 h immersion in chloroform) stability. Moreover, these patterned organic structures can also be integrated on 1.5 μm-thick parylene substrates to yield highly flexible (1 mm radius) and mechanically robust (5,000 bending cycles) thin-film transistors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fast growth and high-titer bioproduction from renewable formate via metal-dependent formate dehydrogenase in Escherichia coli

Microbial bioproduction using one-carbon (C1) feedstocks has the potential to decarbonize the manufacturing of materials, fuels, and chemicals. Formate is a promising C1 feedstock, and the realization of industrial, formatotrophic platform organisms is a key goal for C1-based bioproduction. So far, a major limitation for synthetic formatotrophy has been slow energy supply due to slow formate dehydrogenase activity. Here, we implement a fast, metal-dependent formate dehydrogenase complex in a synthetic formatotrophic Escherichia coli utilizing the reductive glycine pathway. After a short-term evolution, we demonstrate formatotrophic growth of E. coli with a doubling time of less than 4.5 h, comparable to the fastest natural formatotrophs. To further explore the potential of a formate-based bioeconomy, this strain is engineered to produce mevalonate, as well as the terpenoid and aviation fuel precursor isoprenol, using formate we generate directly from the electrochemical reduction of CO2. This work demonstrates an improvement in bioproduct titer from formate, achieving the production of 3.8 g/L of mevalonate. Additionally, the abundant and recalcitrant polymer lignin is chemically decomposed into a formate-rich mixture of small organic acids and subsequently bioconverted into mevalonate. Overall, the described fast-growing, formatotrophic bioproduction strain demonstrates that a sustainable formate bioeconomy is within reach.

Cowan, Aidan E↗
DOE OSTI2020

Electrochemical Behavior of Copper Ion Complexed with Nanoparticle Organic Hybrid Materials

Nanoscale Organic Hybrid Materials (NOHMs) have unique properties that show potential for their use as novel electrolytes that can interact with redox active species. In this work, we probe the effects of adding poly(ethyleneimine)-based NOHMs (NOHM-I-PEI) on copper ion electrochemical reactions. As NOHM-I-PEI is added to a solution containing Cu(II), the voltammetric peak current decreases. This is likely caused by strong complex formation between the PEI nitrogen and the copper, similar to complexation observed in solutions of the polymer with copper. Upon copper addition to a NOHM-I-PEI solution, the pH decreases from 10.1, plateauing at pH = 5.3 at ~3:1 N:Cu ratio indicating that Cu(II) displaces protons. The UV–visible spectra exhibit a Cu-PEI peak, the intensity of which levels off at ~2.8 N:Cu. Acid titration of the N-moieties of the PEI reveals three inflections corresponding to N-environments in the PEI. Upon controlling the pH of the solution by buffering, the "sequestration" of Cu(II) is found to occur when there are unprotonated nitrogens present in the NOHM-I-PEI system; this phenomenon is also supported by UV-vis results. Furthermore, this work highlights the potential of and the design of NOHMs to carry charged electroactive species in solutions along with key factors to control for optimal function.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Developing Materials for High-Energy-Density Solid State Li-S Batteries

Solid-state lithium-sulfur batteries are considered to be the next-generation power source for vehicle applications due to their high energy density (up to 3 times more than current Li-ion) and low cost of sulfur (100 times less than conventional cobalt oxide). However, issues with solid-state electrolyte stability, conduction pathways in the sulfur cathode, and the interface between solid-state electrolyte and sulfur cathode must be solved in order to allow commercialization. This project demonstrates the creation of new, advanced materials which overcome these inherent issues. Current approaches based on polymer or liquid electrolyte with additives have been able to improve stability at the cost of efficiency. In contrast, by creating new hybrid materials it is possible to achieve both stability and efficiency. We developed a novel sulfide-based solid electrolyte, a sulfur-carbon composite cathode, and explored various additives to stabilize the interface of solid electrolyte and cathode. After the desired properties were achieved, these materials were integrated into a high-performance solid-state battery, bringing low-cost high-energy solid-state lithium-sulfur batteries one step closer to reality.

25 ENERGY STORAGE↗
DOE OSTI2024

Infinitely Recyclable Network Polymers, Enabling Sustainable Manufacturing (CRADA Final Report)

This FLO Materials project was aimed at commercializing a new, infinitely recyclable material that can enable closed-loop lifecycles for hard-to-recycle plastics and plastic products. Four hundred million metric tons of virgin plastic is produced each year, yet less than 10% of this material is recycled. In the US alone, 2% of energy consumption is dedicated to the manufacture of virgin plastics, polymer resin, and synthetic rubbers. By keeping plastic materials in circulation longer, we can reduce waste, lower manufacturing costs, cut energy and oil consumption, and drastically reduce greenhouse gas (GHG) emissions. Specifically, FLO’s innovation overcomes the complications associated with salvaging difficult-to-recycle plastics (i.e., contaminated thermoplastic linear polymers, thermoset cross-linked network polymers), which represent at least 20% of total polymer global production, with a recycling rate of near 0%. Chemical recycling of these new polymers through depolymerization allows all additives to be easily removed at room temperature and the recovered monomers to be remanufactured into next generation materials with 100% recovery of mechanical performance and aesthetic quality.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Flexible fire retardant polyisocyanate modified neoprene foam

Lightweight, fire resistant foams have been developed through the modification of conventional neoprene-isocyanate foams by the addition of an alkyl halide polymer. Extensive tests have shown that the modified/neoprene-isocyanate foams are much superior in heat protection properties than the foams heretofore employed both for ballistic and ablative purposes.

Parker, J. A.↗
NASA NTRS1975

Isomer effects on polyimide properties

Polyimide polymers which are thermally stable and processable are developed. The addition of alkyl substituents to an aromatic ring in the polymer backbone is examined along with polyimide precursor amines containing functional groups that allow for post-cure crosslinking. The synthesis of key monomers is reported, including 2,4,6-tris (m-aminobenzyl) 1,3,5-trimethyl benzene and 2,4,6-tris (p-aminobenzyl) 1,3,5-trimethyl benzene. The preparation of a key monomer, 2,5,3-triamino benzophenone, is reported.

Stump, B. L.↗
NASA NTRS1976

New separators for nickel-zinc batteries

Flexible separators consisting of a substrate coated with a mixture of a polymer and organic and inorganic additives were cycle tested in nickel-zinc cells. By substituting a rubber-based resin for polyphenylene oxide in the standard inorganic-organic separator, major improvements in both cell life and flexibility were made. Substituting newsprint for asbestos as the substrate shows promise for use on the zinc electrode and reduces separator cost. The importance of ample electrolyte in the cells was noted. Cycle lives and the characteristics of these flexible, low-cost separators were compared with those of a standard microporous polypropylene separator.

Sheibley, D. W.↗
NASA NTRS2001

Polymer Matrix Composite Lines and Ducts

Since composite laminates are beginning to be identified for use in reusable launch vehicle propulsion systems, a task was undertaken to assess the feasibility of making cryogenic feedlines with integral flanges from polymer matrix composite materials. An additional level of complexity was added by having the feedlines be elbow shaped. Four materials, each with a unique manufacturing method, were chosen for this program. Feedlines were to be made by hand layup (HLU) with standard autoclave cure, HLU with electron beam cure, solvent-assisted resin transfer molding (SARTM), and thermoplastic tape laying (TTL). A test matrix of fill and drain cycles with both liquid nitrogen and liquid helium, along with a heat up to 250 F, was planned for each of the feedlines. A pressurization to failure was performed on any feedlines that passed the cryogenic cycling testing. A damage tolerance subtask was also undertaken in this study. The effects of foreign object impact to the materials used was assessed by cross-sectional examination and by permeability after impact testing. At the end of the program, the manufacture of the electron beam-cured feedlines never came to fruition. All of the TTL feedlines leaked heavily before any cryogenic testing, all of the SARTM feedlines leaked heavily after one cryogenic cycle. Thus, only the HLU with autoclave cure feedlines underwent the complete test matrix. They passed the cyclic testing and were pressurized to failure.

Nettles, A. T.↗
NASA NTRS2005

New Aptes Cross-linked Polymers from Poly(ethylene oxide)s and Cyanuric Chloride for Lithium Batteries

A new series of polymer electrolytes for use as membranes for lithium batteries are described. Electrolytes were made by polymerization between cyanuric chloride and diamino-terminated poly(ethylene oxide)s, followed by cross-linking via a sol-gel process. Thermal analysis and lithium conductivity of freestanding polymer films were studied. The effects of several variables on conductivity were investigated, such as length of backbone PEO chain, length of branching PEO chain, extent of branching, extent of cross-linking, salt content, and salt counterion. Polymer films with the highest percentage of PEO were found to be the most conductive, with a maximum lithium conductivity of 3.9 x 10(exp -5) S/cm at 25 C. Addition of plasticizer to the dry polymers increased conductivity by an order of magnitude.

Tigelaar, Dean M.↗
DOE OSTI2023

Wide temperature range ultracapacitor

A solid state polymer electrolyte is disclosed for use in an ultracapacitor. The electrolyte includes an ionic liquid and a polymer and may include other additives, wherein an ultracapacitor that utilizes the solid state electrolyte is configured to output electrical energy at temperatures between about −40° C. and about 250° C. or more.

Brambilla, Nicolo Michele↗
DOE OSTI2022

Mechanically and Thermally Enhanced 3D-Printed Photocurable Polymer Nanocomposites Containing Functionalized Chitin Nanowhiskers by Stereolithography

Additive manufacturing, or simply 3D printing (3DP), where objects are built through layer-wise material deposition, has gained significant academic and industrial attention as a result of the development of advanced and functional materials requiring rapid, customized, and flexible solutions. In the context of green manufacturing, diversifying environmentally and economically sustainable material portfolios is an essential endeavor for the success of 3DP technology that uses widely available, highly valuable, and renewable materials. Here, we used stereolithography (SLA) for processing methacrylate-based photocurable resins containing crab shell-derived chitin nanowhiskers (CNWs), which are surface-functionalized by reactive acrylate groups. Results from full spectral, thermal, structural, and topological analyses corroborate not only the surface functionalization of CNWs but also indicate the presence of these photocurable CNW (pCNW) fillers in the 3D-printed nanocomposites. Owing to the strong interfacial bond induced by the physical and chemical crosslinking between the pCNW and methacrylate (MA) polymer matrix, the internally formulated nanocomposites displayed enhanced thermomechanical properties (e.g., storage modulus and glass transition temperature) compared to those of commercially available pure SLA resins. For instance, the inclusion of 0.5 wt % pCNW improved the tensile strength and stiffness to up to 78 and 71%, respectively, without compromising the toughness and ductility of the printed material. Accordingly, this result also evidences the compatibility between the filler and resin materials. Consequently, the formation of a crosslinked network in the nanocomposite structure results in a higher thermal stability and activation energy (i.e., up to ~79%) for all the hybrid materials than the pristine MA. Finally, the high-resolution SLA print features, dimensional accuracy, and enhanced mechanical performance of our microstructure-forming functionalized chitin-based nanocomposites make them promising materials for a wide range of robust and high-performance industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Pushing the limits of high-resolution polymer microscopy using antioxidants

High-resolution transmission electron microscopy (HRTEM) has been transformative to the field of polymer science, enabling the direct imaging of molecular structures. Although some materials have remarkable stability under electron beams, most HRTEM studies are limited by the electron dose the sample can handle. Beam damage of conjugated polymers is not yet fully understood, but it has been suggested that the diffusion of secondary reacting species may play a role. As such, we examine the effect of the addition of antioxidants to a series of solution-processable conjugated polymers as an approach to mitigating beam damage. Characterizing the effects of beam damage by calculating critical dose D c values from the decay of electron diffraction peaks shows that beam damage of conjugated polymers in the TEM can be minimized by using antioxidants at room temperature, even if the antioxidant does not alter or incorporate into polymer crystals. As a consequence, the addition of antioxidants pushes the resolution limit of polymer microscopy, enabling imaging of a 3.6Å lattice spacing in poly[(5,6-difluoro-2,1,3-benzothiadiazol-4,7-diyl)-alt-(3,3"-di(2-octyldodecyl)-2,2';5',2";5",2"-quaterthiophene-5,5"-diyl)] (PffBT4T-2OD).

36 MATERIALS SCIENCE↗
NASA NTRS1988

Additives Improve Processing Of Polyimides

Melt-processable polyimides maintain desirable polymer properties prepared by adding small amounts of certain low-molecular-weight, thermally stable additives. Useful in preparing void-free polyimide composites from higher flow resins that wet out fibers at lower processing temperatures. Applied to preparing high-temperature polyimide adhesives allowing enhanced wetting of adherends and ultimately better adhesion. Improvement to processing polyimides and potential application for production of films, coatings, adhesives, and composites.

St. Clair, Terry L.↗