Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “parameter compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26
All sourcesNASA NTRSDOE OSTI
NASA NTRS2025

Sealing Europa’s Vents By Vapor Deposition: An Order-of-Magnitude Study

Fractures and vents in the ice crust of Europa, exposing the sub-surface ocean or liquid-water inclusions to the vacuum, might be responsible for the generation of planetary-scale water-vapor plumes. During its passage through the ice, the plume vapor is expected to partially condense on the cold ice walls. Together with other effects (water spillage, compression forces, etc.) this mechanism likely contributes to sealing the vent. In this work, we develop a lumped-parameter model to analyze the sealing timescales associated to water-vapor deposition alone. Neglecting all other possible mechanisms, we find shutting-off times roughly compatible with the 7-hour plume observed in 2012 by the Hubble Space Telescope, suggesting that vapor deposition might have played a major role in sealing the vent. A map of sealing times vs. plume density, mass flow rate and aperture areas is given. Plume quantities from the literature are analyzed and compared to our results. For a given plume density/mass flow rate, small apertures would be sealed quickly by vapor deposition and are thus incompatible with observations.

Europa↗
DOE OSTI2023

Temperature-based reactive flow model for TATB plastic bonded explosives

A new reactive flow model is presented for TATB-based plastic bonded explosives, applicable to shock initiation and detonation problems of differing initial temperature. Temperature disequilibrium is assumed between unreacted explosive, material in the vicinity of compressed defects (called hot spots), and detonation products. The model incorporates temperature-dependent decomposition reaction rates. Arrhenius model parameters were derived from subscale quantum-based molecular dynamics simulations of shock-induced TATB decomposition. Further, a model of detonation carbon aggregation is incorporated, describing the late-time slow release of energy inherent to detonation in TATB-based materials. The predictive ability of the model in the shock initiation regime is tested against recent thin pulse experiments on PBX 9502. Here, the model is found to perform equally well in predicting the size effect curve of ambient, cold, and hot PBX 9502 rate sticks.

Chemistry - Chemical explosives↗
NASA NTRS1991

Compressive testing of filament-wound cylinders

An experimental investigation has been conducted on the compressive buckling and failure of filament-wound circular cylinders. This investigation identifies one of the relationships between structural performance and scale, as well as some of the causes of reduced structural performance in large-scale structures. It is hypothesized that this effect is related to two conditions: first, the number of fiber tow undulations; and second, the percentage of weak interfaces within the structure. The effect of winding pattern and the resulting location of the fiber undulations were studied by varying the winding parameters. Three types of cylinders were manufactured from Amoco T650-35/1908 graphite/epoxy preimpregnated tow with different winding sequences (0/+/-60)s, (+/-30/90)s, and (90/+/-30)s. The (90/+/-30)s cylinders were manufactured with two different winding patterns (distributed and classical) and radius-to-thickness ratios (15 and 55). All cylinders were loaded in compression to failure. Comparisons of the compressive strength and failure modes demonstrate the relationship between the winding parameters, scale, and structural performance of filament-wound composite cylinders.

Jensen, David W.↗
NASA NTRS1995

Sensitivity Analysis of Wing Aeroelastic Responses

Design for prevention of aeroelastic instability (that is, the critical speeds leading to aeroelastic instability lie outside the operating range) is an integral part of the wing design process. Availability of the sensitivity derivatives of the various critical speeds with respect to shape parameters of the wing could be very useful to a designer in the initial design phase, when several design changes are made and the shape of the final configuration is not yet frozen. These derivatives are also indispensable for a gradient-based optimization with aeroelastic constraints. In this study, flutter characteristic of a typical section in subsonic compressible flow is examined using a state-space unsteady aerodynamic representation. The sensitivity of the flutter speed of the typical section with respect to its mass and stiffness parameters, namely, mass ratio, static unbalance, radius of gyration, bending frequency, and torsional frequency is calculated analytically. A strip theory formulation is newly developed to represent the unsteady aerodynamic forces on a wing. This is coupled with an equivalent plate structural model and solved as an eigenvalue problem to determine the critical speed of the wing. Flutter analysis of the wing is also carried out using a lifting-surface subsonic kernel function aerodynamic theory (FAST) and an equivalent plate structural model. Finite element modeling of the wing is done using NASTRAN so that wing structures made of spars and ribs and top and bottom wing skins could be analyzed. The free vibration modes of the wing obtained from NASTRAN are input into FAST to compute the flutter speed. An equivalent plate model which incorporates first-order shear deformation theory is then examined so it can be used to model thick wings, where shear deformations are important. The sensitivity of natural frequencies to changes in shape parameters is obtained using ADIFOR. A simple optimization effort is made towards obtaining a minimum weight design of the wing, subject to flutter constraints, lift requirement constraints for level flight and side constraints on the planform parameters of the wing using the IMSL subroutine NCONG, which uses successive quadratic programming.

Issac, Jason Cherian↗
DOE OSTI2020

H2OI95: A Stand-Alone Fortran Code for Evaluating the IAPWS-95 Equation-of-State Model for Water (Rev. 1)

H2OI95 is a stand-alone Fortran code for evaluating the IAPWS-95 equation-of-state model for the thermodynamic properties of water. It also evaluates the corresponding thermochemical properties of water consistent with the CODATA recommendations. The IAPWS-95 model is based on a model equation for the dimensionless Helmholtz energy for which the primary variables are the inverse reduced temperature (τ = T cr /T ) and reduced density (δ = ρ/ρ cr ). Here T is the absolute temperature (K), ρ is density (kg/m³), and the subscript “ cr ” refers to the critical point of water (647.096 K and 22.064 MPa pressure in this model, for which ρ cr is 322 kg/m³). The code solves four basic types of problems, distinguished by the specified inputs: 1. Temperature (K) and density (ρ kg/m³) or reduced density (δ) 2. Temperature (K) and pressure (MPa). 3. Temperature (K) on the saturation (liquid-vapor equilibrium) curve 4. Pressure (MPa) on the saturation curve. Each type of problem is run using a corresponding input (text) file. All but the first type of problem require iteration. For example, to solve for desired temperature and pressure, the reduced density must be adjusted to give the desired pressure. Iteration is accomplished using the Newton-Raphson method, though the secant method is also used in solving the fourth type of problem. For the last three types of problems, H2OI95 has been used to conduct numerical studies of convergence and the problem of multiple numerical solutions, some of which are not physically valid. Obtaining valid results depends mainly on appropriate choice of starting values for the density. The default values used in H2OI95 appear to consistently lead to generally desired results. With modification (not addressed here), H2OI95 can be used to support SUPCRT92 and similar codes that compute chemical thermodynamic properties of species and reactions over a wide range of temperature and pressure (273.16-1273K and 0-1000 MPa). Version 1.1 of this software calculates an extended set of water properties, including some derivable solely from IAPWS-95, such as the isobaric thermal expansivity and the isothermal compressibility, and still other properties based on supplementary models sanctioned by IAPWS, including the dynamic viscosity, thermal conductivity, surface tension, and static dielectric constant, and various other properties (notably Debye-Hückel parameters) derivable from the dielectric constant and its partial derivatives with respect to temperature and pressure. A coding error in Version 1.0 was identified while testing the implementation of the viscosity model. This error is described in Appendix C. It mainly affects calculation of “higher order” properties such as compressibility and heat capacity near the critical point.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Fiber orientation and porosity in large-format extrusion process: The role of processing parameters

Controlling fiber orientation and porosity in short-fiber thermoplastic composites is important for enhancing mechanical, electrical and thermal properties in large-format additive manufacturing. This study employs a factorial design of experiments (DoE) to assess the effects of nozzle diameter (5.08 mm–10.16 mm), temperature (230–250 °C), and extruder screw speed (150–280 rpm) on flow rate, shear rate, porosity, fiber orientation, fiber length and tensile strength in 20 % carbon fiber-filled acrylonitrile butadiene styrene. ANOVA results show that screw speed significantly impacts flow rate, while nozzle diameter and temperature have lesser effects. Shear rate increases with smaller nozzles and higher speeds. Porosity decreases from 5.58 % with a 10.16 mm nozzle to 3.11 % with a 5.08 mm nozzle at 150 rpm due to increased shear rates, which induce shear thinning, reducing viscosity and facilitating gas escape. Larger nozzles (10.16 mm) produce larger, more heterogeneous pores, while smaller nozzles (5.08 mm) yield smaller, uniform pores. Beads produced with the 5.08 mm nozzle exhibit longer fiber lengths due to reduced residence time, lower shear stress, and better alignment. Fiber orientation improves with smaller nozzles due to higher shear rates but decreases with higher screw speeds (280 rpm) due to shorter residence times. The highest fiber alignment (A xx ∼ 0.65) and low porosity (∼3%) were achieved with a 5.08 mm nozzle at 150 rpm, while equivalent additive manufacturing-compression molding samples exhibited better tensile strength (∼93 MPa) under these conditions. In conclusion, these findings emphasize the importance of optimizing processing parameters to enhance fiber alignment and reduce porosity for improved mechanical performance.

Design of experiments↗
NASA NTRS1992

Buckling behavior of long symmetrically laminated plates subjected to combined loads

A parametric study of the buckling behavior of infinitely long symmetrically laminated anisotropic plates subjected to combined loadings is presented. The loading conditions considered are axial tension and compression, transverse tension and compression, and shear. Results obtained using a special purpose analysis, well suited for parametric studies are presented for clamped and simply supported plates. Moreover, results are presented for some common laminate constructions, and generic buckling design charts are presented for a wide range of parameters. The generic design charts are presented in terms of useful nondimensional parameters, and dependence of the nondimensional parameters on laminate fiber orientation, stacking sequence, and material properties is discussed. An important finding of the study is that the effects of anisotropy are much more pronounced in shear-loaded plates than in compression loaded plates. In addition, the effects of anisotropy on plates subjected to combined loadings are generally manifested as a phase shift of self-similar buckling interaction curves. A practical application of this phase shift is the buckling resistance of long plates can be improved by applying a shear loading with a specific orientation. In all cases considered, it is found that the buckling coefficients of infinitely long plates are independent of the bending stiffness ratio (D sub 11/D sub 22) sup 1/4.

Nemeth, Michael P.↗
NASA NTRS2024

Direct Ink Write 3D Printing of Fully Dense and Functionally Graded Liquid Metal Elastomer Foams

Liquid metal (LM) elastomer composites offer promising potential in soft robotics, wearable electronics, and human-machine interfaces. Direct ink write (DIW) 3D printing offers a versatile manufacturing technique capable of precise control over LM microstructures, yet challenges such as interfilament void formation in multilayer structures impact material performance. Here, a DIW strategy is introduced to control both LM microstructure and material architecture. Investigating three key process parameters–nozzle height, extrusion rate, and nondimensionalized nozzle velocity–it is found that nozzle height and velocity predominantly influence filament geometry. The nozzle height primarily dictates the aspect ratio of the filament and the formation of voids. A threshold print height based on filament geometry is identified; below the height, significant surface roughness occurs, and above the ink fractures, which facilitates the creation of porous structures with tunable stiffness and programmable LM microstructure. These porous architectures exhibit reduced density and enhanced thermal conductivity compared to cast samples. When used as a dielectric in a soft capacitive sensor, they display high sensitivity (gauge factor = 9.0), as permittivity increases with compressive strain. These results demonstrate the capability to simultaneously manipulate LM microstructure and geometric architecture in LM elastomer composites through precise control of print parameters, while maintaining geometric fidelity in the printed design.

Spencer Pak↗
DOE OSTI2022

Non-local large-strain FFT-based formulation and its application to interface-dominated plasticity of nano-metallic laminates

Here, this paper presents a novel formulation and its robust numerical implementation of strain-gradient (SG) crystal plasticity within a large-strain (LS) elasto-viscoplastic (EVP) fast Fourier transform (FFT)-based micromechanical model. The resulting non-local SG-LS-EVPFFT formulation is used to model and understand the process of kink band formation during layer-parallel compression of nano-metallic laminates (NMLs). NMLs are layered composites with nanoscale thicknesses, thus requiring consideration of the interaction between dislocations and interfaces within the micromechanical model. The length-scale parameter of the SG model is calibrated by simulating a double pile-up and comparing predictions to analytical solution. This required new expressions for the defect energy, resulting in more accurate double pile-up predictions. The calibrated SG-LS-EVPFFT model is then used to simulate layer-parallel compression of copper-niobium NML. Formation of kink bands is predicted, and the model is used to rationalize the microscopic mechanisms enabling the formation process. It is found that accumulation of dislocations at interfaces leads to activation of layer-parallel slip, which in turn leads to kink band formation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural characterization and equibiaxial flexural strength of CeO 2 and Ti-doped CeO 2

In this study, the synthesis of CeO 2 and titanium dioxide (TiO 2 ) doped CeO 2 (TDC) monoliths are investigated, and their fracture strength is assessed using an equibiaxial flexure testing technique at room temperature. Pellets were synthesized using conventional powder processing and sintering methods to produce the desired characteristics. The TiO 2 dopant concentration was optimized at 0.1 wt % TiO 2 to obtain dense, solid-solution pellets with an enhanced grain microstructure. A ball-on-ring fixture was used to obtain the TRS and Weibull parameters of over 30 pellets for CeO 2 and 0.1 wt % TDC to compare fracture behavior. The TRS of CeO 2 pellets ranged from 88 to 160 MPa and the TRS of 0.1 wt % TDC pellets ranged from 102 to 171 MPa, both being consistent with published values. Weibull parameters, such as characteristic strength and Weibull modulus, were extracted as 129 MPa and 8.5 for CeO 2 and 150 MPa and 9.3 for 0.1 wt % TDC, respectively. Although Hertzian contact damage was observed on compressive surfaces, failure initiation occurred on the tensile surfaces of both types of samples. Fracture surface analysis for CeO 2 indicated a predominantly intergranular fracture while 0.1 wt % TDC had a predominantly transgranular fracture mode. Finally, the TRS of 0.1 wt % TDC resulted in increased Weibull parameters when compared to CeO 2 , indicating sample chemistry and microstructure impact mechanical behavior for these samples.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Using a surrogate-assisted Bayesian framework to calibrate the runoff-generation scheme in the Energy Exascale Earth System Model (E3SM) v1

Abstract. Runoff is a critical component of the terrestrial water cycle, and Earth system models (ESMs) are essential tools to study its spatiotemporal variability. Runoff schemes in ESMs typically include many parameters so that model calibration is necessary to improve the accuracy of simulated runoff. However, runoff calibration at a global scale is challenging because of the high computational cost and the lack of reliable observational datasets. In this study, we calibrated 11 runoff relevant parameters in the Energy Exascale Earth System Model (E3SM) Land Model (ELM) using a surrogate-assisted Bayesian framework. First, the polynomial chaos expansion machinery with Bayesian compressed sensing is used to construct computationally inexpensive surrogate models for ELM-simulated runoff at 0.5∘ × 0.5∘ for 1991–2010. The error metric between the ELM simulations and the benchmark data is selected to construct the surrogates, which facilitates efficient calibration and avoids the more conventional, but challenging, construction of high-dimensional surrogates for the ELM simulated runoff. Second, the Sobol' index sensitivity analysis is performed using the surrogate models to identify the most sensitive parameters, and our results show that, in most regions, ELM-simulated runoff is strongly sensitive to 3 of the 11 uncertain parameters. Third, a Bayesian method is used to infer the optimal values of the most sensitive parameters using an observation-based global runoff dataset as the benchmark. Our results show that model performance is significantly improved with the inferred parameter values. Although the parametric uncertainty of simulated runoff is reduced after the parameter inference, it remains comparable to the multimodel ensemble uncertainty represented by the global hydrological models in ISMIP2a. Additionally, the annual global runoff trend during the simulation period is not well constrained by the inferred parameter values, suggesting the importance of including parametric uncertainty in future runoff projections.

58 GEOSCIENCES↗
DOE OSTI2025

Temperature-based reactive flow model for triaminotrinitrobenzene (TATB) plastic bonded explosives

A new reactive flow model is presented for triaminotrinitrobenzene (TATB)-based plastic bonded explosives, applicable to shock initiation and steady detonation problems of differing initial temperature. Temperature disequilibrium is assumed between unreacted explosive, material in the vicinity of compressed defects (called hot spots), and reaction products. The model incorporates temperature-dependent decomposition reaction rates. Particularly, Arrhenius model parameters were derived from quantum-based molecular dynamics simulations of TATB decomposition. Further, a model of detonation carbon aggregation is incorporated, describing the slow release of energy inherent to detonation in TATB-based materials. Model parameters were calibrated against gas gun shock initiation experiments and steady detonation rate stick tests. The predictive ability of the model in the shock initiation regime is tested against recent thin pulse experiments. The model is found to perform equally well in predicting the size-effect curve of ambient, cold, and hot rate sticks. The present work demonstrates the viability of incorporating results from subscale simulations into a continuum-scale reactive flow model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Diagnostics of Magnetohydrodynamic Modes in the Interstellar Medium through Synchrotron Polarization Statistics

One of the biggest challenges in understanding magnetohydrodynamic (MHD) turbulence is identifying the plasma mode components from observational data. Previous studies on synchrotron polarization from the interstellar medium (ISM) suggest that the dominant MHD modes can be identified via statistics of Stokes parameters, which would be crucial for studying various ISM processes such as the scattering and acceleration of cosmic rays, star formation, and dynamo. In this paper, we present a numerical study of the synchrotron polarization analysis (SPA) method through systematic investigation of the statistical properties of the Stokes parameters. We derive the theoretical basis for our method from the fundamental statistics of MHD turbulence, recognizing that the projection of the MHD modes allows us to identify the modes dominating the energy fraction from synchrotron observations. Based on the discovery, we revise the SPA method using synthetic synchrotron polarization observations obtained from 3D ideal MHD simulations with a wide range of plasma parameters and driving mechanisms, and present a modified recipe for mode identification. We propose a classification criterion based on a new SPA+ fitting procedure, which allows us to distinguish between Alfvén mode and compressible/slow mode dominated turbulence. We further propose a new method to identify fast modes by analyzing the asymmetry of the SPA+ signature and establish a new asymmetry parameter to detect the presence of fast mode turbulence. Additionally, we confirm through numerical tests that the identification of the compressible and fast modes is not affected by Faraday rotation in both the emitting plasma and the foreground.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1971

Possible flow regimes of adiabatic one-dimensional compressible fluid flow with friction in convergent and divergent ducts.

An analytical solution for the compressible one-dimensional flow in convergent and divergent ducts with friction is obtained. It is found that a nondimensional parameter, N, can be formed using the friction factor, duct half-angle and the ratio of specific heats of the gas. Seven flow regimes are describable with the solution, based on certain bounds on the magnitude of N. The regimes are discussed and corollary data are presented graphically.

Shouman, A. R.↗
NASA NTRS1975

Advanced beaded and tubular structural panels

A program to develop lightweight beaded and tubular structural panels is described. Applications include external surfaces, where aerodynamically acceptable, and primary structure protected by heat shields. The design configurations were optimized and selected with a computer code which iterates geometric parameters to satisfy strength, stability, and weight constraints. Methods of fabricating these configurations are discussed. Nondestructive testing produced extensive combined compression, shear, and bending test data on local buckling specimens and large panels. The optimized design concepts offer 25 to 30% weight savings compared to conventional stiffened sheet construction.

Musgrove, M. D.↗
NASA NTRS1977

All-tantalum electrolytic capacitor

Device uses single-compression tantalum-to-tantalum seal. Single-compression seal allows better utilization of volume within device. As result of all-tantalum case and lengthened cathode, electrical parameters, particularly equivalent series resistance and capacitance stability, improved over silver-cased capacitor.

Green, G. E., Jr.↗
NASA NTRS1993

Venus bow shocks at unusually large distances from the planet

Recent analysis of data from the Pioneer Venus Orbiter (PVO) has shown that the bow shock often travels to unusually large distances from the planet when the solar wind magnetosonic Mach number is near unity. We suggest that distant bow shocks can be explained as an integral part of the response of the global solar wind/Venus interaction to the anomalous local solar wind conditions that existed during the time of these observations. The lower-than-normal plasma beta and magnetosonic Mach number are in a parameter regime for which the usual fast-mode bow shock close to the planet may not provide the necessary compression and deflection of the solar wind. Using MHD simulations we show that, for these conditions, the usual fast shock is replaced by a bow shock consisting of an intermediate shock near the Sun-Venus line and a fast shock at large distances from the Sun-Venus line. This composite bow shock propagates upstream away from the planet at a low speed and appears to be approaching a new equilibrium stand-off location at a large distance from the planet.

Steinolfson, R. S.↗
NASA NTRS2001

Parametric Data from a Wind Tunnel Test on a Rocket-Based Combined-Cycle Engine Inlet

A 40-percent scale model of the inlet to a rocket-based combined-cycle (RBCC) engine was tested in the NASA Glenn Research Center 1- by 1-Foot Supersonic Wind Tunnel (SWT). The full-scale RBCC engine is scheduled for test in the Hypersonic Tunnel Facility (HTF) at NASA Glenn's Plum Brook Station at Mach 5 and 6. This engine will incorporate the configuration of this inlet model which achieved the best performance during the present experiment. The inlet test was conducted at Mach numbers of 4.0, 5.0, 5.5, and 6.0. The fixed-geometry inlet consists of an 8 deg.. forebody compression plate, boundary layer diverter, and two compressive struts located within 2 parallel sidewalls. These struts extend through the inlet, dividing the flowpath into three channels. Test parameters investigated included strut geometry, boundary layer ingestion, and Reynolds number (Re). Inlet axial pressure distributions and cross-sectional Pitot-pressure surveys at the base of the struts were measured at varying back-pressures. Inlet performance and starting data are presented. The inlet chosen for the RBCC engine self-started at all Mach numbers from 4 to 6. Pitot-pressure contours showed large flow nonuniformity on the body-side of the inlet. The inlet provided adequate pressure recovery and flow quality for the RBCC cycle even with the flow separation.

Fernandez, Rene↗