SEARCH · Engineering Papers

Results for “optimal input design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Guaranteed robustness properties of multivariable, nonlinear, stochastic optimal regulators

The robustness of optimal regulators for nonlinear, deterministic and stochastic, multi-input dynamical systems is studied under the assumption that all state variables can be measured. It is shown that, under mild assumptions, such nonlinear regulators have a guaranteed infinite gain margin; moreover, they have a guaranteed 50 percent gain reduction margin and a 60 degree phase margin, in each feedback channel, provided that the system is linear in the control and the penalty to the control is quadratic, thus extending the well-known properties of LQ regulators to nonlinear optimal designs. These results are also valid for infinite horizon, average cost, stochastic optimal control problems.

Tsitsiklis, J. N.↗

NASA NTRS1984

Guaranteed robustness properties of multivariable nonlinear stochastic optimal regulators

Tsitsiklis, J. N.↗

NASA NTRS2005

The Impact of Model Uncertainty on Spatial Compensation in Structural Acoustic Control

Turbulent boundary layer (TBL) noise is considered a primary contribution to the interior noise present in commercial airliners. There are numerous investigations of interior noise control devoted to aircraft panels; however, practical realization is a potential challenge since physical boundary conditions are uncertain at best. In most prior studies, pinned or clamped boundary conditions were assumed; however, realistic panels likely display a range of boundary conditions between these two limits. Uncertainty in boundary conditions is a challenge for control system designers, both in terms of the compensator implemented and the location of transducers required to achieve the desired control. The impact of model uncertainties, specifically uncertain boundaries, on the selection of transducer locations for structural acoustic control is considered herein. The final goal of this work is the design of an aircraft panel structure that can reduce TBL noise transmission through the use of a completely adaptive, single-input, single-output control system. The feasibility of this goal is demonstrated through the creation of a detailed analytical solution, followed by the implementation of a test model in a transmission loss apparatus. Successfully realizing a control system robust to variations in boundary conditions can lead to the design and implementation of practical adaptive structures that could be used to control the transmission of sound to the interior of aircraft. Results from this research effort indicate it is possible to optimize the design of actuator and sensor location and aperture, minimizing the impact of boundary conditions on the desired structural acoustic control.

Clark, Robert L.↗

NASA NTRS1989

Global sensitivity analysis in control-augmented structural synthesis

In this paper, an integrated approach to structural/control design is proposed in which variables in both the passive (structural) and active (control) disciplines of an optimization process are changed simultaneously. The global sensitivity equation (GSE) method of Sobieszczanski-Sobieski (1988) is used to obtain the behavior sensitivity derivatives necessary for the linear approximations used in the parallel multidisciplinary synthesis problem. The GSE allows for the decoupling of large systems into smaller subsystems and thus makes it possible to determine the local sensitivities of each subsystem's outputs to its inputs and parameters. The advantages in using the GSE method are demonstrated using a finite-element representation of a truss structure equipped with active lateral displacement controllers, which is undergoing forced vibration.

Bloebaum, Christina L.↗

NASA NTRS1994

Software for continuum modeling of controls-structures interactions

It is clear that computer software is needed to assist in the generation of the equations of motion for complex, flexible spacecraft. Daniel Poelaert of ESTEC has developed the software DISTEL with which he has modeled the structural dynamics for different satellites. He is interested in expanding the capabilities of DISTEL to include structural damping and control systems. Unfortunately, the software has not been released. The author has developed similar software, PDEMOD, which has been used to model the Spacecraft control Laboratory Experiment (SCOLE), the Solar Array Flight Experiment (SAFE), the Mini-MAST truss, and the LACE satellite. PDEMOD has been used also for optimal parameter estimation and integrated control-structures design. PDEMOD is also being extended to include structural damping and control systems which are imbedded into the same equations for the structural dynamics. This paper will address the formulation of the equations for the structural dynamics of spacecraft structures which are constructed of a 3-dimensional arrangement of rigid bodies and flexible beam elements. Control system dynamics are imbedded into the same equations so that model order reduction approximations are not necessary. The input data consists of the physical data of the elements and the topological information describing how the elements are connected. PDEMOD accomplishes the following: (1) automatically assembles the equations of motion for the entire structural model; (2) calculates the modal frequencies; (3) calculates the mode shapes; (4) generates perspective views of the mode shapes; and (5) forms selected transfer functions. The software PDEMOD continues to be developed to provide additional features to assist in analyzing and synthesizing control and structural systems for flexible spacecraft.

Taylor, Lawrence W., Jr.↗

NASA NTRS2000

Parametric Model of an Aerospike Rocket Engine

A suite of computer codes was assembled to simulate the performance of an aerospike engine and to generate the engine input for the Program to Optimize Simulated Trajectories. First an engine simulator module was developed that predicts the aerospike engine performance for a given mixture ratio, power level, thrust vectoring level, and altitude. This module was then used to rapidly generate the aerospike engine performance tables for axial thrust, normal thrust, pitching moment, and specific thrust. Parametric engine geometry was defined for use with the engine simulator module. The parametric model was also integrated into the iSIGHT multidisciplinary framework so that alternate designs could be determined. The computer codes were used to support in-house conceptual studies of reusable launch vehicle designs.

Korte, J. J.↗

NASA NTRS2000

Parametric Model of an Aerospike Rocket Engine

A suite of computer codes was assembled to simulate the performance of an aerospike engine and to generate the engine input for the Program to Optimize Simulated Trajectories. First an engine simulator module was developed that predicts the aerospike engine performance for a given mixture ratio, power level, thrust vectoring level, and altitude. This module was then used to rapidly generate the aerospike engine performance tables for axial thrust, normal thrust, pitching moment, and specific thrust. Parametric engine geometry was defined for use with the engine simulator module. The parametric model was also integrated into the iSIGHTI multidisciplinary framework so that alternate designs could be determined. The computer codes were used to support in-house conceptual studies of reusable launch vehicle designs.

Korte, J. J.↗

NASA NTRSDate not supplied

Impact of Handling Qualities on Motor Sizing for Multirotor Aircraft with Urban Air Mobility Missions

Control models of three NASA Urban Air Mobility (UAM) reference vehicles (the quadrotor, octocopter, and Lift+Cruise (LPC)) were created and compared to determine the effect of rotor number and disk loading on control margin and design. The heave and yaw axes demand more actuator usage than the roll and pitch axes. Between heave and yaw, heave was the more demanding of the two because of the dependence of heave on the engine speed controller (ESC). When the feedback gains for all three vehicles were optimized to Level 1 handling qualities (HQs) specifications using CONDUIT, the ESC for the octocopter was the most stable and had the highest rise time (time for the rotor to respond to an input), while the LPC ESC was the least stable and had the smallest rise time. Rise time corresponds to the time required for rotor response. When actuator usage was translated to current margin, torque margin, and power margin, heave was the most demanding axis, followed by yaw, roll, and then pitch for all three vehicles. The results emphasize the importance of an accurate motor model within the control system architecture.

Impact↗

NASA NTRS1989

Determination of design and operation parameters for upper atmospheric research instrumentation to yield optimum resolution with deconvolution, appendix 3

The Always-Convergent Iterative Noise Removal and Deconvolution Method of Ioup is applied as a single-filter in the transform domain to deconvolution with both narrow and wide Gaussian impulse response functions. The wraparound error for both cases is also studied. A method is developed by which one can find the optimum iteration number for single-filter iterative deconvolution of sampled data. The method employs the mean square error (MSE), the square of the difference between the deconvolved result and the input, for optimization. The MSE decreases as the deconvolution iterations proceed, but at the optimum iteration number, the MSE starts to increase. This procedure is repeated for signal-to-noise ratio of 10 to 150. The optimum iteration number and the MSE are plotted vs SNR. By knowing the SNR for a particular experiment, one can find the optimum iteration number and MSE.

Ioup, George E.↗

NASA NTRS1974

Digital explicit model following with unstable model dynamics

In the optimal regulator formulation of discrete explicit model following the Riccati equation may fail to reach a steady-state value for model dynamics which are not asymptotically stable. Such conditions often arise in aircraft applications when flying quality criteria based on step inputs are used to define the model equations. Mathematical conditions are presented which insure a steady-state value of the model-following gain matrix regardless of the behavior of the underlying Riccati equation. These results are applied to the design of a model-following controller for the lateral motion of a typical fighter aircraft using unstable model equations.

Armstrong, E. S.↗

NASA NTRS1976

Optimal control of a low wing-loading STOL aircraft

Linear optimal quadratic control theory is applied to a low wing-loading STOL aircraft for ride quality and flight path following. Design criteria include minimum rms response to wind turbulence and desired transient response characteristics. Design techniques include proper choosing of design versus evaluation models, choosing appropriate performance index responses, and use of classical evaluation techniques. Results are obtained through a combination of frequency response shaping and gust observation. Effects of control rate and authority saturation are examined with a new rapid calculation of random input describing functions. Parameter sensitivity is also evaluated using a Liapunov type matrix equation.

Cunningham, T. B.↗

NASA NTRS1988

STRUTEX: A prototype knowledge-based system for initially configuring a structure to support point loads in two dimensions

The purpose of this research effort is to investigate the benefits that might be derived from applying artificial intelligence tools in the area of conceptual design. Therefore, the emphasis is on the artificial intelligence aspects of conceptual design rather than structural and optimization aspects. A prototype knowledge-based system, called STRUTEX, was developed to initially configure a structure to support point loads in two dimensions. This system combines numerical and symbolic processing by the computer with interactive problem solving aided by the vision of the user by integrating a knowledge base interface and inference engine, a data base interface, and graphics while keeping the knowledge base and data base files separate. The system writes a file which can be input into a structural synthesis system, which combines structural analysis and optimization.

Rogers, James L.↗

NASA NTRS1976

Formulation of a methodology for power circuit design optimization

A methodology for optimizing power-processor designs is described which achieves optimization with respect to some power-processor characteristic deemed particularly desirable by the designer, such as weight or efficiency. Optimization theory based on Lagrange multipliers is reviewed together with nonlinear programming techniques employing penalty functions. The methodology, the task of which is to minimize an objective function subject to design constraints, is demonstrated with the aid of four examples: optimum-weight core selection for an inductor with a predetermined winding size, optimum-weight inductor design with a given loss constraint, optimum-loss inductor design with a given weight constraint, and a comparison of optimum-weight single- and two-stage input-filter designs with identical loss and other requirement constraints. Closed-form solutions for the first three examples are obtained by applying the Lagrange-multiplier method, but solutions for the last example are found numerically through the use of the sequential unconstrained minimization technique.

Yu, Y.↗

NASA NTRS1993

Surrogates for numerical simulations; optimization of eddy-promoter heat exchangers

Although the advent of fast and inexpensive parallel computers has rendered numerous previously intractable calculations feasible, many numerical simulations remain too resource-intensive to be directly inserted in engineering optimization efforts. An attractive alternative to direct insertion considers models for computational systems: the expensive simulation is evoked only to construct and validate a simplified, input-output model; this simplified input-output model then serves as a simulation surrogate in subsequent engineering optimization studies. A simple 'Bayesian-validated' statistical framework for the construction, validation, and purposive application of static computer simulation surrogates is presented. As an example, dissipation-transport optimization of laminar-flow eddy-promoter heat exchangers are considered: parallel spectral element Navier-Stokes calculations serve to construct and validate surrogates for the flowrate and Nusselt number; these surrogates then represent the originating Navier-Stokes equations in the ensuing design process.

Patera, Anthony T.↗

NASA NTRS1988

A 1050 K Stirling space engine design

As part of the NASA CSTI High Capacity Power Program on Conversion Systems for Nuclear Applications, Sunpower, Inc. completed for NASA Lewis a reference design of a single-cylinder free-piston Stirling engine that is optimized for the lifetimes and temperatures appropriate for space applications. The NASA effort is part of the overall SP-100 program which is a combined DOD/DOE/NASA project to develop nuclear power for space. Stirling engines have been identified as a growth option for SP-100 offering increased power output and lower system mass and radiator area. Superalloy materials are used in the 1050 K hot end of the engine; the engine temperature ratio is 2.0. The engine design features simplified heat exchangers with heat input by sodium heat pipes, hydrodynamic gas bearings, a permanent magnet linear alternator, and a dynamic balance system. The design shows an efficiency (including the alternator) of 29 percent and a specific mass of 5.7 kg/kW. This design also represents a significant step toward the 1300 K refractory Stirling engine which is another growth option of SP-100.

Penswick, L. Barry↗

NASA NTRS2000

The Dynamic Planner: The Sequencer, Scheduler, and Runway Allocator for Air Traffic Control Automation

The Dynamic Planner (DP) has been designed, implemented, and integrated into the Center-TRACON Automation System (CTAS) to assist Traffic Management Coordinators (TMCs), in real time, with the task of planning and scheduling arrival traffic approximately 35 to 200 nautical miles from the destination airport. The TMC may input to the DP a series of current and future scheduling constraints that reflect the operation and environmental conditions of the airspace. Under these constraints, the DP uses flight plans, track updates, and Estimated Time of Arrival (ETA) predictions to calculate optimal runway assignments and arrival schedules that help ensure an orderly, efficient, and conflict-free flow of traffic into the terminal area. These runway assignments and schedules can be shown directly to controllers or they can be used by other CTAS tools to generate advisories to the controllers. Additionally, the TMC and controllers may override the decisions made by the DP for tactical considerations. The DP will adapt to computations to accommodate these manual inputs.

Wong, Gregory L.↗

NASA NTRS1986

A methodology for designing robust multivariable nonlinear control systems

A new methodology is described for the design of nonlinear dynamic controllers for nonlinear multivariable systems providing guarantees of closed-loop stability, performance, and robustness. The methodology is an extension of the Linear-Quadratic-Gaussian with Loop-Transfer-Recovery (LQG/LTR) methodology for linear systems, thus hinging upon the idea of constructing an approximate inverse operator for the plant. A major feature of the methodology is a unification of both the state-space and input-output formulations. In addition, new results on stability theory, nonlinear state estimation, and optimal nonlinear regulator theory are presented, including the guaranteed global properties of the extended Kalman filter and optimal nonlinear regulators.

Grunberg, D. B.↗

NASA NTRS2001

Spacecraft Formation Flying Maneuvers Using Linear-Quadratic Regulation with No Radial Axis Inputs

Regarding multiple spacecraft formation flying, the observation has been made that control thrust need only be applied coplanar to the local horizon to achieve complete controllability of a two-satellite (leader-follower) formation. A formulation of orbital dynamics using the state of one satellite relative to another is used. Without the need for thrust along the radial (zenith-nadir) axis of the relative reference frame ' propulsion system simplifications and weight reduction may be accomplished. Several linear-quadratic regulators (LQR) are explored and compared based on performance measures likely to be important to many missions, but not directly optimized in the LQR designs. Maneuver simulations are performed using commercial ODE solvers to propagate the Keplerian dynamics of a controlled satellite relative to an uncontrolled leader. These short maneuver simulations demonstrate the capacity of the controller to perform changes from one formation geometry to another. This work focusses on formations in which the controlled satellite has a relative trajectory which projects onto the local horizon of the uncontrolled satellite as a circle. This formation has potential uses for distributed remote sensing systems.

Starin, Scott R.↗