SEARCH · Engineering Papers

Results for “nonlinear elasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 469 records · Page 26

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Strains and tilts on crustal blocks

Geodetic work done over the past century is examined to investigate block motion in areas of intense tectonic deformation, with special attention to geodetic releveling data obtained for Japan. Problems in interpreting strainmeter and tiltmeter to study the behavior of crustal blocks and block boundaries are discussed. Block dimensions of 5 to 50 km seem to occur frequently in regions of intense tectonic activity. Block boundaries are often considerably weaker than contiguous crustal blocks, resulting in a concentration of strains at boundaries and decrease of strains within blocks. Block to block variations in tilt phase and magnitude are observed. There is some evidence that block boundaries may exhibit strain-dependent elastic properties or respond viscoelastically, possibly accounting for the slow transmission of tectonic deformation reported in Japan. If nonlinear behavior is characteristic of regions fragmented by crustal blocks, it will generally not be possible to apply a site correction factor based on the observed distortion of tidal or seismic strains in interpreting secular strains.

Bilham, R. G.↗

NASA NTRS1984

Inviscid fluid in high frequency excitation field

The influence of high frequency excitations (HFE) on a fluid is investigated. The response to these excitations is decomposed in two parts: 'slow' motion, which practically remains unchanged during the vanishingly small period tau, and 'fast' motion whose value during this period is negligible in terms of displacements, but is essential in terms of the kinetic energy. After such a decomposition the 'slow' and 'fast' motions become nonlinearly coupled by the corresponding governing equations. This coupling leads to an 'effective' potential energy which imparts some 'elastic' properties to the fluid and stabilizes laminar flows.

Zak, M.↗

NASA NTRS1987

Nonlinear simulation of a flexible aircraft in maneuvering flight

A mathematical model integrating nonlinear rigid-body flight mechanics and linear aeroelastic dynamics is examined; the equations of motion for an elastic aircraft in accelerated flight are developed using Lagrangian mechanics. This approach is used to construct a simulation model of an F/A-18 (configured with tip missiles) which includes angular/elastic inertial coupling (IC). In general, the elastic modes significantly affected by IC were aerodynamically decoupled from the rest of the model. The affected modes were those which induced changes in total aircraft mass distribution. The elastic effect is noticeable if deformation-induced mass distribution changes are significant with respect to modal mass and modal frequencies. A modal parameter is presented which characterizes the level of IC between elastic momentum and rigid-body angular momentum.

Buttrill, Carey S.↗

NASA NTRS1992

Geometric modeling of inflatable structures for lunar base

A modular inflatable structure consisting of thin, composite membranes is presented for use in a lunar base. Results from a linear elastic analysis of the structure indicate that it is feasible in the lunar environment. Further analysis requires solving nonlinear equations and accurately specifying the geometries of the structural members. A computerized geometric modeling technique, using bicubic Bezier surfaces to generate the geometries of the inflatable structure, was conducted. Simulated results are used to create three-dimensional wire frames and solid renderings of the individual components of the inflatable structure. The component geometries are connected into modules, which are then assembled based upon the desired architecture of the structure.

Nowak, Paul S.↗

NASA NTRS2004

Finite Element Modeling Used to Study Stress Distribution on the Foot

A method to study the stress distribution inside the forefoot during walking was developed at the Cleveland Clinic Foundation by a researcher from the NASA Glenn Research Center. In this method, a semiautomated process was outlined to create a three-dimensional, patient-specific, finite element model (FEM) of the forefoot using magnetic resonance images (MRI). The images were processed in Matlab using the k-nearest neighbor (k-NN) classification algorithm and Sobel edge detection to separate the different tissue types: bone, skin, fat, and muscle. This information was used to create curves and surfaces that were exported to an FEM preprocessor known as Truegrid. In Truegrid, eight-noded or brick elements were created by using surface mapping. The FEM was processed and postprocessed in Abaqus. Material properties of the models were obtained from past experiments such as fat pad confined compression, skin axial and biaxial tests, muscle in vivo compressive tests, and reference literature (bone properties). Nonlinear (hyperelastic) material models were used for the skin (epidermis and dermis), fat, and muscles; and a linear elastic model was used for the bones. Muscle activation during walking yielded uncertainties in the muscle material model since contracted muscles are stiffer than relaxed muscles. These uncertainties were resolved by performing a sensitivity analysis of the muscle material properties. The original properties were multiplied by arbitrary factors of 2, 3, 0.5, and 0.33. The strain and stress distributions, as well as the locations of peak values, were similar in all cases. The peak contact pressure P obtained for each case varied with respect to the applied factor f as follows:

Morales, Nelson↗

NASA NTRS1973

Nonlinear analysis of a shock-loaded membrane.

Results from a computer method for analyzing the unsteady interaction of a fluid stream and a flat circular elastic membrane are presented. The loading on the membrane is assumed to be caused by the firing of a shock tube. The fluid pressures and velocities are determined from a scheme based on the numerical method of characteristics, and the membrane is analyzed using exact relations for membrane strain. The interactive solution is found to give peak stresses 40% lower than a solution which assumes a pressure invariant in space and time.

Madden, R.↗

DOE OSTI2025

Modeling kinetic effects of charged vacancies on electromechanical responses of ferroelectrics: Rayleighian approach

Understanding the time-dependent effects of charged vacancies on the electromechanical responses of materials is at the forefront of research for designing materials exhibiting metal-insulator transitions and memristive behavior. A Rayleighian approach is used to develop a model for studying the nonlinear kinetics of the reaction leading to generation of vacancies and electrons via the dissociation of vacancy-electron pairs. Also, diffusion and elastic effects of charged vacancies are considered to model polarization-electric potential and strain-electric potential hysteresis loops. The model captures multiphysics phenomena by introducing couplings among polarization, the electric potential, stress, strain, and concentrations of charged (multivalent) vacancies and electrons (treated as classical negatively charged particles), where the concentrations can vary due to association-dissociation reactions. A derivation of coupled time-dependent equations based on the Rayleighian approach is presented. Three limiting cases of the governing equations are considered, highlighting the effects of (1) nonlinear reaction kinetics on the generation of charged vacancies and electrons, (2) Vegard's law (i.e., the concentration-dependent local strain) on asymmetric strain-electric potential relations, and (3) coupling between a fast component and the slow component of the net polarization on the polarization-electric-field relations. The Rayleighian approach discussed in this work should pave the way for developing a multiscale modeling framework in a thermodynamically consistent manner while capturing multiphysics phenomena in ferroelectric materials. Published by the American Physical Society 2025

Kumar, Rajeev (ORCID:0000000194943488)↗

DOE OSTI2026

Nonlinear viscoelastic response of silicone additively manufactured direct ink write (DIW) foams under repetitive compression

To investigate dynamic fatigue behavior of foam in military protective applications, such as helmets, additively manufactured (AM) foams were compressively strained into the plateau region using a reduced design of experiments. A simple power law was found to govern the decline in dynamic stiffness (complex modulus) as the foams underwent the purchase order requirement of 10,000 cycles of small deformation in the plateau region. This rate of decline was newly found to correlate with the degree of nonlinearity in the material’s deformation, quantified using total harmonic distortion. Materials with low nonlinearity exhibited relatively stable stiffness across cycles, while those with high nonlinearity experienced greater losses. The observed nonlinearity depended on both applied stress and strain rate. A strong linear correlation (R 2 = 0.78) was identified between second-order nonlinearity and the time-dependent stiffness response. Two lattice structures were examined: face-centered tetragonal (FCT) and simple cubic (SC). The SC material exhibited higher total harmonic distortion (5%) and lower stiffness retention than the FCT (2%). In conclusion, these results suggest that for cyclic compression applications in a wide variety of industries such as packaging, personal protective equipment, or aerospace, selecting materials with lower stress and greater structural uniformity can enhance the stability of dynamic performance.

42 ENGINEERING↗

DOE OSTI2024

The nonlinear mechanics of highly extensible plant epidermal cell walls

Plant epidermal cell walls maintain the mechanical integrity of plants and restrict organ growth. Mechanical analyses can give insights into wall structure and are inputs for mechanobiology models of plant growth. To better understand the intrinsic mechanics of epidermal cell walls and how they may accommodate large deformations during growth, we analyzed a geometrically simple material, onion epidermal strips consisting of only the outer (periclinal) cell wall, ~7 μm thick. With uniaxial stretching by >40%, the wall showed complex three-phase stress–strain responses while cyclic stretching revealed reversible and irreversible deformations and elastic hysteresis. Stretching at varying strain rates and temperatures indicated the wall behaved more like a network of flexible cellulose fibers capable of sliding than a viscoelastic composite with pectin viscosity. We developed an analytic framework to quantify nonlinear wall mechanics in terms of stiffness, deformation, and energy dissipation, finding that the wall stretches by combined elastic and plastic deformation without compromising its stiffness. We also analyzed mechanical changes in slightly dehydrated walls. Their extension became stiffer and more irreversible, highlighting the influence of water on cellulose stiffness and sliding. This study offers insights into the structure and deformation modes of primary cell walls and presents a framework that is also applicable to tissues and whole organs.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS1991

Passive dynamic controllers for nonlinear mechanical systems

A methodology for model-independant controller design for controlling large angular motion of multi-body dynamic systems is outlined. The controlled system may consist of rigid and flexible components that undergo large rigid body motion and small elastic deformations. Control forces/torques are applied to drive the system and at the same time suppress the vibration due to flexibility of the components. The proposed controller consists of passive second-order systems which may be designed with little knowledge of the system parameter, even if the controlled system is nonlinear. Under rather general assumptions, the passive design assures that the closed loop system has guaranteed stability properties. Unlike positive real controller design, stabilization can be accomplished without direct velocity feedback. In addition, the second-order passive design allows dynamic feedback controllers with considerable freedom to tune for desired system response, and to avoid actuator saturation. After developing the basic mathematical formulation of the design methodology, simulation results are presented to illustrate the proposed approach to a flexible six-degree-of-freedom manipulator.

Juang, Jer-Nan↗

NASA NTRS1979

Nonlinear effects on composite laminate thermal expansion

Analyses of Graphite/Polyimide laminates shown that the thermomechanical strains cannot be separated into mechanical strain and free thermal expansion strain. Elastic properties and thermal expansion coefficients of unidirectional Graphite/Polyimide specimens were measured as a function of temperature to provide inputs for the analysis. The + or - 45 degrees symmetric Graphite/Polyimide laminates were tested to obtain free thermal expansion coefficients and thermal expansion coefficients under various uniaxial loads. The experimental results demonstrated the effects predicted by the analysis, namely dependence of thermal expansion coefficients on load, and anisotropy of thermal expansion under load. The significance of time dependence on thermal expansion was demonstrated by comparison of measured laminate free expansion coefficients with and without 15 day delay at intermediate temperature.

Hashin, Z.↗

NASA NTRS2000

Nonlinearity and Strain-Rate Dependence in the Deformation Response of Polymer Matrix Composites Modeled

There has been no accurate procedure for modeling the high-speed impact of composite materials, but such an analytical capability will be required in designing reliable lightweight engine-containment systems. The majority of the models in use assume a linear elastic material response that does not vary with strain rate. However, for containment systems, polymer matrix composites incorporating ductile polymers are likely to be used. For such a material, the deformation response is likely to be nonlinear and to vary with strain rate. An analytical model has been developed at the NASA Glenn Research Center at Lewis Field that incorporates both of these features. A set of constitutive equations that was originally developed to analyze the viscoplastic deformation of metals (Ramaswamy-Stouffer equations) was modified to simulate the nonlinear, rate-dependent deformation of polymers. Specifically, the effects of hydrostatic stresses on the inelastic response, which can be significant in polymers, were accounted for by a modification of the definition of the effective stress. The constitutive equations were then incorporated into a composite micromechanics model based on the mechanics of materials theory. This theory predicts the deformation response of a composite material from the properties and behavior of the individual constituents. In this manner, the nonlinear, rate-dependent deformation response of a polymer matrix composite can be predicted.

Goldberg, Robert K.↗

NASA NTRS1978

Tensile and compressive stress-strain behavior of heat treated boron-aluminum

An experimental study was conducted to assess the effects of heat treatment and cyclic mechanical loading on the tensile and compressive stress-strain behavior of six boron-aluminum composites having different laminate orientations and being subjected to different heat treatments. The heat treatments were as-fabricated, T6, and T6N consisting of T6 treatment followed by cryogenic quench in liquid nitrogen prior to testing. All laminates were tested in monotonic and cyclic compression, while the tensile-test data are taken from the literature for comparison purposes. It is shown that the linear elastic range of the T6- and T6N-condition specimens is larger than that of the as-fabricated specimens, and that cyclic loading in tension or compression strain hardens the specimens and extends the linear elastic range. For laminates containing 0-deg plies, the stress-strain behavior upon unloading is found to be nonlinear, whereas the other laminates exhibit a linear behavior upon unloading. Specimens in the T6 and T6N conditions show higher strain hardening than the as-fabricated specimens.

Kennedy, J. M.↗

NASA NTRS1980

Generalized Grueneisen tensor from solid nonlinearity parameters

Anharmonic effects in solids are often described in terms of generalized Grueneisen parameters which measure the strain dependence of the lattice vibrational frequencies. The relationship between these parameters and the solid nonlinearity parameters measured directly in ultrasonic harmonic generation experiments is derived using an approach valid for normal-mode elastic wave propagation in any crystalline direction. The resulting generalized Grueneisen parameters are purely isentropic in contrast to the Brugger-Grueneisen parameters which are of a mixed thermodynamic state. Experimental data comparing the isentropic generalized Grueneisen parameters and the Brugger-Grueneisen parameters are presented.

Cantrell, J. H., Jr.↗

NASA NTRS1983

Development of a simplified analytical method for representing material cyclic response

Development of a simplified method for estimating structural inelastic stress and strain response to cyclic thermal loading is presented. The method assumes that high temperature structural response is the sum of time independent plastic and time dependent elastic/creep components. The local structural stress and strain response predicted by linear elastic analysis is modified by the simplified method to predict the inelastic response. The results with simulations by a nonlinear finite element analysis and used time independent plasticity and unified time dependent material model are compared.

Moreno, V.↗

NASA NTRS1999

A Viscoelastic Hybrid Shell Finite Element

An elastic large displacement thick-shell hybrid finite element is modified to allow for the calculation of viscoelastic stresses. Internal strain variables are introduced at he element's stress nodes and are employed to construct a viscous material model. First order ordinary differential equations relate the internal strain variables to the corresponding elastic strains at the stress nodes. The viscous stresses are computed from the internal strain variables using viscous moduli which are a fraction of the elastic moduli. The energy dissipated by the action of the viscous stresses in included in the mixed variational functional. Nonlinear quasi-static viscous equilibrium equations are then obtained. Previously developed Taylor expansions of the equilibrium equations are modified to include the viscous terms. A predictor-corrector time marching solution algorithm is employed to solve the algebraic-differential equations. The viscous shell element is employed to numerically simulate a stair-step loading and unloading of an aircraft tire in contact with a frictionless surface.

Johnson, Arthur↗

NASA NTRS1993

Inelastic deformation of metal matrix composites

A theoretical model capable of predicting the thermomechanical response of continuously reinforced metal matrix composite laminates subjected to multiaxial loading was developed. A micromechanical model is used in conjunction with nonlinear lamination theory to determine inelastic laminae response. Matrix viscoplasticity, residual stresses, and damage to the fiber/matrix interfacial zone are explicitly included in the model. The representative cell of the micromechanical model is considered to be in a state of generalized plane strain, enabling a quasi two-dimensional analysis to be performed. Constant strain finite elements are formulated with elastic-viscoplastic constitutive equations. Interfacial debonding is incorporated into the model through interface elements based on the interfacial debonding theory originally presented by Needleman, and modified by Tvergaard. Nonlinear interfacial constitutive equations relate interfacial tractions to displacement discontinuities at the interface. Theoretical predictions are compared with the results of an experimental program conducted on silicon carbide/titanium (SiC/Ti) unidirectional, (O4), and angle-ply, (+34)(sub s), tubular specimens. Multiaxial loading included increments of axial tension, compression, torque, and internal pressure. Loadings were chosen in an effort to distinguish inelastic deformation due to damage from matrix plasticity and separate time-dependent effects from time-independent effects. Results show that fiber/matrix debonding is nonuniform throughout the composite and is a major factor in the effective response. Also, significant creep behavior occurs at relatively low applied stress levels at room temperature.

Lissenden, C. J.↗

NASA NTRS1986

Simplified cyclic structural analyses of SSME turbine blades

Anisotropic high-temperature alloys are used to meet the safety and durability requirements of turbine blades for high-pressure turbopumps in reusable space propulsion systems. The applicability to anisotropic components of a simplified inelastic structural analysis procedure developed at the NASA Lewis Research Center is assessed. The procedure uses as input the history of the total strain at the critical crack initiation location computed from elastic finite-element analyses. Cyclic heat transfer and structural analyses are performed for the first stage high-pressure fuel turbopump blade of the space shuttle main engine. The blade alloy is directionally solidified MAR-M 246 (nickel base). The analyses are based on a typical test stand engine cycle. Stress-strain histories for the airfoil critical location are computed using both the MARC nonlinear finite-element computer code and the simplified procedure. Additional cases are analyzed in which the material yield strength is arbitrarily reduced to increase the plastic strains and, therefore, the severity of the problem. Good agreement is shown between the predicted stress-strain solutions from the two methods. The simplified analysis uses about 0.02 percent (5 percent with the required elastic finite-element analyses) of the CPU time used by the nonlinear finite element analysis.

Kaufman, A.↗